CYBEX 11070-999 H, Eagle 11070 Owner's And Service Manual

Cybex Eagle® Arm Curl

Owner’s and Service Manual

Strength Systems

Part Number 11070-999 H

www.cybexinternational.com

Cybex Eagle® Arm Curl

Owner’s and Service Manual

Strength Systems

Part Number 11070-999 H

Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.
Eagle® and its mark are registered trademarks of Cybex International, Inc.

DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual. We reserve the right to
revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such
revisions or changes.

© Copyright 2010, Cybex International, Inc. All rights reserved.
Printed in the United States of America.

10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX [phone]
www.cybexinternational.com • [e-mail] • 11070-999 H • March 2010

Table of Contents

1 Safety

Safety. . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Warning/Caution Decals . . . . . . . . . . . 1-2

Regular Maintenance Activities . . . . . . 1-5

Using Proper Form . . . . . . . . . . . . . . . 1-5

2 Exercises

General Exercise Guidelines . . . . . . . . 2-1

3 Customer Service

Contacting Service. . . . . . . . . . . . . . . . 3-1

Ordering parts . . . . . . . . . . . . . . . . . . . 3-1

Return Material Authorization (RMA). . 3-1

Damaged Parts . . . . . . . . . . . . . . . . . . 3-2

4 Assembly

Assembly . . . . . . . . . . . . . . . . . . . . . . . 4-1

5 Maintenance

Daily Procedures . . . . . . . . . . . . . . . . . 5-1

Weekly Procedures . . . . . . . . . . . . . . . 5-4

Yearly Procedures . . . . . . . . . . . . . . . . 5-6

Environment. . . . . . . . . . . . . . . . . . . . . 5-7

Storage . . . . . . . . . . . . . . . . . . . . . . . . 5-7

6 Service

Parts Lists . . . . . . . . . . . . . . . . . . . . . . 6-4

Exploded-View Diagram . . . . . . . . . . . 6-5

Page i

Cybex Eagle 11070 Arm Curl Owner’s Manual

1 - Safety

Safety

Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper operation of the

equipment and review all labels.

WARNING: Serious injury could occur if these safety precautions are not observed:

User Safety Precautions

Obtain a medical exam prior to beginning an exercise program.•
Read and understand warning labels and user manual prior to exercising. Obtain instruction •

prior to use.
Keep body and clothing free from and clear of all moving parts.•
Inspect machine prior to use. • DO NOT use if it appears damaged or inoperable.
DO NOT • attempt to fi x a broken or jammed machine. Notify fl oor staff.
Use the machine only for the intended use. • DO NOT modify the machine.
Be sure that the weight pin is completely inserted. Use only the pin provided by the manufacturer. •

If unsure seek assistance.
Never pin the weights in an elevated position. • DO NOT use the machine if found in this condition.

See assistance from fl oor staff.
Children must not be allowed near these machines. Teenagers must be supervised.•

DO NOT• use if guards are missing or damaged.
DO NOT • use dumbbells or other incremental weights, except those provided by the manufacturer.

Inspect all cables and belts and connections prior to use. • DO NOT use if any components are worn, frayed or
damaged.

DO NOT• remove any labeling from equipment. Replace any damaged labels.
Stop exercising if you feel faint, dizzy or experience pain at any time while exercising and consult your •

physician.

Facility Safety Precautions

Read the Owner’s Manual carefully before assembling, servicing or using the equipment. •
Securely anchor each machine to the fl oor using the anchor holes provided in each machine.•

NOTE: Cybex is not responsible for the actual anchoring of equipment. Consult with a professional

contractor.

NOTE: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8” grade 2 bolts or better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any

leg or frame not in contact with surface using fl at washers.

Safety

Page 1-1

Cybex Eagle 11070 Arm Curl Owner’s Manual

Make sure that each machine is set up and operated on a solid level surface. • Do not install equipment on an
uneven surface.

Make sure that all users are properly trained on how to use the equipment.•
Make sure there is enough room for safe access and operation of the equipment. •
Perform regular maintenance checks on the equipment. Also pay close attention to all areas most susceptible to wear, •

including (but not limited to) cables, pulleys, belts and grips.
Immediately replace worn or damaged components. If unable to immediately replace worn or damaged components •

then remove from service until the repair is made.
Use only Cybex supplied components to maintain/repair the equipment.•
Keep a repair log of all maintenance activities.•
Inspect all cables and belts and connections prior to use. • DO NOT use if any components are worn, frayed or

damaged.

NOTE: It is the sole responsibility of the user/owner or facility operator to ensure that regular maintenance is performed.

Safety Guidelines And Practices

Cybex recommends that all fi tness equipment be used in a supervised area. It is recommended that the equipment be
located in an access controlled area. Control is the responsibility of the owner. The extent of control is at the discretion of
the owner.

It is the responsibility of the purchaser/user of Cybex products to read and understand the owner’s manual, and warning
labels; as well as instruct all individuals, whether end users or supervising personnel, on proper usage of the equipment.

PROPER USAGE:

Use machine only as described in the manual. Failing to follow proper instructions may result in injury.
Do Not Lean Against or Pull On the framework, weight stack, or any component, whether machine is at rest or in use.

Inappropriate or improper use may result in injury to users or third parties (bystanders).
Do not use machine if it is not located on a solid level surface or is improperly installed.
Provide an adequate safety perimeter between the machine, walls and other equipment to ensure that the facility has the

proper clearance for usage and training.

SECURING EQUIPMENT:

The machine has holes in the feet, which allow for ease in anchoring to the fl oor. Cybex strongly recommends that,
to eliminate rocking, tipping or falling over due to incorrect usage and misuse, equipment be secured to a solid, level
surface.

1. The solid, level surface should not deviate more than 1/8” over a 10’ distance or as defi ned and required by local
building and architectural codes.

2. Anchoring of equipment must be completed by a qualifi ed licensed contractor.

Safety
Page 1-2

Cybex Eagle 11070 Arm Curl Owner’s Manual

3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when anchoring the
equipment to the fl oor.

4. Due to the wide variation of fl ooring on which machines may be anchored or installed, verify anchoring method and
anchoring fasteners with a qualifi ed and licensed contractor.

5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position..

6. Do not use machine until it is properly anchored.
MAINTENANCE:

Preventative maintenance allows proper equipment operation and reduces the risk of injury. Perform the maintenance
requirements as specifi ed in the manual.

STANDARD COMPLIANCE:

Cybex products meet or exceed applicable ASTM and EN Standards.

Warning/Caution Decals

Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
Caution decals indicate a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury.
The warning and caution decals are shown on the following page. The diagrams following the decals show where each

decal is located.

Safety

Page 1-3

Cybex Eagle 11070 Arm Curl Owner’s Manual

A

Seat may fall if
improperly engaged.

Verify seat is secure

B

before exercising to
avoid injury.

CAUTION

4520-362-4

C

Keep away from moving
parts. Failure to do so could
result in personal injury.

CAUTION

8500-026-4

Safety
Page 1-4

4605-381-4 A

Cybex Eagle 11070 Arm Curl Owner’s Manual

Arm Curl - 11070

C

C

DESCRIPTION PART NO.

Warning DecalA. ..................4605-381-4

Caution DecalB. ...................4520-362-4

Caution DecalC. ...................8500-026-4

A

B

Safety

Page 1-5

Cybex Eagle 11070 Arm Curl Owner’s Manual

Regular Maintenance Activities

Preventative maintenance activities must be performed to maintain normal operation of your equipment.
Keeping a log sheet of all maintenance actions will assist you in staying current with all preventative
maintenance activities. The preventative maintenance actions are described in detail in Chapter 5.
Briefl y, they include:

Daily

1. Clean upholstery.

2. Clean back panel.
Weekly

1. Inspect all nuts and bolts for looseness. Tighten as required.

2. Inspect all cables and belts for damage or wear (see Chapter 5). If a cable or belt is worn or

damaged, immediately discontinue use until cable or belt has been replaced.

3. Check for worn handles, worn snap links, and worn warning labeling. Replace all worn parts

immediately.

4. Inspect for loose or worn grips. Replace all loose or worn grips immediately.

5. Inspect weight stacks for proper alignment and operation. Correct all improper alignment and

operation issues immediately.

6. Lubricate guide rods using automotive engine oil only.
Yearly

1. Replace all cables and belts at least annually.

Using Proper Form

Before working out, read and understand the exercises located on the placard and in Chapter 2.

Safety
Page 1-6

Cybex Eagle 11070 Arm Curl Owner’s Manual

2 - Exercise

Intended Use

The intended use of this equipment is to aid or
improve general physical fi tness and exercise.
For Commercial use.

Instructions

Read and understand all instructions and warnings
prior to using this machine. See Chapter 1, Safety in
the Eagle Owner’s Manual or consult with fl oor staff.

START

MUSCLES USED

Biceps Brachii, Brachialis,

Brachioradialis

FINISH

NOTE: Motion Developed: Elbow Flexion

NOTE: All adjustment points on the machine have yellow handles or knobs.
NOTE: See next page for “Set Up” and “Movement”.
NOTE: Do not turn knob when weight stack is elevated

Exercise
Page 2-1

Cybex Eagle 11070 Arm Curl Owner’s Manual

Set Up

1. Adjust seat height so that your arms are straight and fully supported by the pad.

2. Adjust chest pad so that the elbows align with the axis of rotation.

3. Grasp handles.
Movement

1. Pull the handles up towards your shoulders.

Exercise
Page 2-2

Cybex Eagle 11070 Arm Curl Owner’s Manual

3 - Customer Service

Contacting Service

Hours of phone service are Monday through Friday from 8:30 to 6:00 p.m. Eastern Standard Time.
For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239.
For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300

or fax [phone].

Find information on the web at www.cybexintl.com or by e-mail at [e-mail].

Ordering Parts

Fax order to 508-533-5183. To speak with a customer service representative, call 888-462-9239 (for customers
living within the USA) or 508-533-4300 (for customers outside the USA). You may also contact us through e-mail
at [e-mail]

Having the following information ready when calling will assist our Cybex representatives in serving you.

Unit Serial Number

•

Product Name•

The unit serial number and product name can be found on the serial number decal. See Chapter 6 for exact
location of serial number decal.

Part Description•
Part Number•

Part descriptions and part numbers are located in Chapter 6 of this manual.

Shipping Address

•

Contact Name•

Return Material Authorization (RMA)

In addition to your shipping address and contact name, your account number is helpful but not required.
The Return Material Authorization (RMA) system outlines the procedures to follow when returning

material for placement, repair or credit. The system assures that returned materials are properly handled and
analyzed. Follow the following procedures carefully.

Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will request a RMA
from Cybex, if applicable. Under no circumstances will defective parts or equipment be accepted by Cybex without
proper RMA and an Automated Return Service (ARS) label.

Customer

Service

Page 3-1

Cybex Eagle 11070 Arm Curl Owner’s Manual

1. Call the Customer Service Hot Line listed above for the return of any item that is defective.

2. Provide the technician with a detailed description of the problem you are having or the defect in the
item you wish to return.

3. Provide the model and serial number of your Cybex equipment.

4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for
evaluation and repair or replacement. The technician will assign you a RMA number and will send
you an ARS label. The ARS label and the RMA numbers must be clearly displayed on the outside
of the package that contains the item(s) to be returned. Include the description of the problem, the
serial number of the equipment and the name and address of the owner in the package along with
the part(s).

5. Forward the package through UPS to Cybex.

Attn: Customer Service Department
Cybex International, Inc.
1975 24th Ave SW

Owatonna, MN 55060

NOTE: Merchandise returned without an RMA number on the outside of the package or shipments sent

COD will not be accepted by the Cybex receiving department.

Damaged Parts

Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility
of the carrier (UPS, Federal Express, trucking companies, etc.)

Apparent Damage - Upon receipt of your shipment, check all items carefully. Any damage seen with a
visual check must be noted on the freight bill and signed by the carrier’s agent. Failure to do so will result
in the carriers refusal to honor your damage claim. The carrier will provide you with the required forms for
fi ling such claims.

Concealed Damage - Damage not seen with a visual check upon receipt of a shipment but
notices later must be reported to the carrier as soon as possible. Upon discovery of the
damage, a written or phone request to the carrier asking them to perform an inspection of the materials
must be made within ten days of the delivery date. Keep all shipping containers and packing materials as
they will be needed in the inspection process. The carrier will provide you with an inspection report and
the necessary forms for fi ling a concealed damage claim.
Concealed damage claim is the carrier’s responsibility.

Customer
Service
Page 3-2

Cybex Eagle 11070 Arm Curl Owner’s Manual

4 - Assembly

TOOLS REQUIRED

7/32” Allen wrench•
3/4” Allen wrench•
9/16” Wrench •
3/4” Socket or wrench•
External snap ring pliers•
Phillips screwdriver•
Medium weight automotive engine oil•
Torque Wrench •

NOTE: Two people will be required for this procedure.
NOTE: It is the responsibility of the facility owner/owner of the equipment to ensure that there

is appropriate clearance around each machine to allow for safe use and passage.

1. Read and understand all instructions thoroughly before starting any of the
procedures listed on this instruction sheet.

2. Verify you have received the appropriate confi guration.

Verify that you received the correct color machine that you ordered.A.
Verify you received weight plates and weight plate decals.B.
Verify you received the Cybex Eagle Arm Curl Owner’s Manual.C.
Verify you received the warranty sheet. D.

3. Move to desired location.

Note the diminsions of the machine:A.
idle - 58 L x 41 W x 58 H inches

147.32 L x 104.14 W x 147.32 H cm
in use - 58 L x 41 W x 58 H inches

147.32 L x 104.14 W x 147.32 H cm
Machine Weight (with weight stack) - 501 lbs. (227.24 kg)

Determine if you can move your machine through the required doorway(s).B.
If the machine fi ts through the doorway(s), move machine to desired location and skip to step 5. C.
If weight stacks need to be installed proceed to step 6.D.
If the machine does not fi t through the door-way(s) then see step 4. E.

4. Doorway Instructions.

NOTE: If your machine fi ts through the doorway then skip step 4. If your machine does not fi t through

the doorway then perform step 4.

Carefully remove each (standard) cone-shaped shipping support using a 3/4” socket or wrench.A.

Assembly

Page 4-1

Cybex Eagle 11070 Arm Curl Owner’s Manual

With an assistant, carefully remove the six Button Head B.
Socket Cap Screws (BHSCS) securing the two halves of
the frame. See Figure 1.

Carefully move each half through the door-way to the C.
desired location.

With an assistant, carefully attach each half together D.
using the six BHSCS removed in step 4B. See Figure 1.

Continue on with step 5B.E.

5. Remove shipping feet and remove the back shrouds.

Carefully remove each (standard) cone-shaped A.
shipping support (using a 3/4” socket or wrench).

Carefully place rubber feet (supplied with machine) B.
on each foot of the frame.

Cut shipping tie securing top weight.C.
Lift top weight and turn the Increment Weight Adjusting D.

Knob to select all 15 lbs.
Remove the three Phillips head screws securing the E.

top (back) shroud and carefully remove the shroud.
See Figure 2.

Locknut (4)

BHSCS (4)

Locknut (2)

BHSCS (2)

Figure 1

Phillips Head
Screw (3)

Figure 2

Loosen bottom two screws shown in Figure 3. F.

NOTE: Do not remove the bottom two screws.

Remove the top two screws securing the back shroud G.
assembly. See Figure 4.

Carefully slide rear shroud assembly upward and remove.H.

6. Install the weight stack.

Note how the increment weights are installed.A.
With an assistant holding the increment weights, move B.

the adjusting knob to 0 lbs. and remove all six increment
weights (three each side).

Using an external snap ring pliers, remove the upper C.
snap ring from one of the guide rods and carefully
lower the guide rod. See Figure 5.

Remove lower snap ring and wave washer from the D.
guide rod. Repeat steps 6C and 6D to remove both
snap rings from other guide rod.

If possible, lean guide rods outward, away from machine E.
in order to provide the most room for installing weight
plates.

Screw

Figure 3

Screw

Figure 4

Upper snap ring

Frame

Wave washer

Slide top weight up and out of machine and carefully F.
set it aside.

Assembly
Page 4-2

Lower snap ring

Guide rod

Figure 5

Cybex Eagle 11070 Arm Curl Owner’s Manual

Wipe guide rods clean over entire length. Lubricate with light coating of medium weight automotive engine oil.G.
Carefully install each weight plate one at a time. H. NOTE: When installing weight plates, position plates so wide

edges of bushing face upward and narrow edges of bushing face downward. See Figures 6A and 6B.

CORRECT

WIDE bushing

edge faces

upward

Figure 6A Figure 6B

Slide top weight onto guide rods.I.
Place lower snap ring and wave washer onto guide rod (about 3” from the top end of guide rod).J.
Raise guide rod up through mounting hole and install the upper snap ring.K.
Lower guide rod and secure lower snap ring. L.

Repeat steps 6J - 6L for the other guide rod.

7. Belt Routing.

Verify belt is routed through top of pulley bracket A.
and then route end of belt down to the top weight.

Slide belt through slot in belt clamp.B.
Verify the belt clamp on the top weight is positioned C.

properly with the top pulley. NOTE: The belt must

have a straight path from the pulley to the belt clamp.
See Figure 7. NOTE: Figure 7 shows the top view,
looking from the top pulley down to the top plate.
Slide belt through slot in belt clamp.

Verify belt and insert are installed properly, D.
as shown in Figure 8A. NOTE: Do not install

the insert backwards as shown in Figure 8B.

WRONG

NARROW

bushing edge

NOTE: The narrow bushing

edge must face downward.

Belt

Top Pulley

Insert

Increment Weight
Adjusting Knob

Figure 7

Correct belt routing Wrong belt routing

Insert

Belt

Insert

Set Screw

Belt

Stem

Figure 8A Figure 8B

Stem

Assembly

Page 4-3

Cybex Eagle 11070 Arm Curl Owner’s Manual

Pull belt tight and secure belt to clamp with the two E.
set screws. NOTE: Torque set screws 300-350 in./lbs.
See Figure 9.

Belt

Belt clamp
insert

Place weight stack pin in each plate to verify proper installation.F.
Without selecting any resistance, lift top weight up and down G.

(simulating normal operation).
Have an assistant verify that the belt is moving smoothly and is H.

routed straight from the top pulley bracket to the
top weight belt clamp.

Reinstall the six increment weights that were removed I.
in step 6B. See Figure 10.

Turn the Increment Weight Adjusting Kob to select all J.
15 lbs.

8. Install back shrouds.

Carefully place shroud assembly back into position A.
on the two bottom screws. See Figure 11.

Install the top two screws securing the back shroud B.
assembly. See Figure 12.

Install the three Phillips head screws securing the C.
top (back) shroud. See Figure 13.

Belt clamp

Set screw

Figure 9

Grooves

Increment Weights

Figure 10

Figure 11

Figure 12

Screw

Screw

Phillips Head
Screw (3)

Assembly
Page 4-4

Figure 13

Cybex Eagle 11070 Arm Curl Owner’s Manual

180

81.0

144.0

135.0

126.0

117.0

10

8.0

200

99.0

90.0

300

280

260

240

220

320

340

153.0

180.0

360

171.0

162.0

400

380

20

9.0

72.0

63.0

54.0

45.0

36.0

40

18.0

140

120

100

80

60

160

9. Install weight plate decals.

NOTE: You have the option to use pounds, kilograms or both.

Slowly and carefully peel off back side of decal. See A.
Figure 14. NOTE: When peeling off back cover, make

sure that the decals remain attached to the front sticker.

Align holes in decal with appropriate holes in weight B.
stack. NOTE: Do not allow the adhesive to touch

weight stack at this time.

Insert a guide pin through each hole of the template. C.

NOTE: A guide pin can be anything that fi ts through the
weight stack hole, such as a weight stack selector pin.

Carefully align decal and rub it onto weight plates. D.
Carefully remove front side, leaving decals adhering E.

to weight plates. See Figure 15.

NOTE: It is important that you perform regular inspection

and maintenance activities on your equipment. See
the CYBEX Eagle Owner’s Manual for inspection and
maintenance activities. If you do not have a CYBEX
Eagle Owner’s Manual or if you have any questions
or concerns, call CYBEX Customer Relations at
888-462-9239.

10. Verify proper operation

11. Anchor machine to the fl oor.

Front

Back

Figure 14

Guide Rod

Weight Stack

Kilograms

Pounds

Figure 15

Securely anchor machine to the fl oor using the anchor holes provided in each machine. A.

NOTE: Cybex is not responsible for the actual anchoring of equipment. Consult with a professional contractor.
NOTE: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8” grade 2 bolts or better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or frame not

in contact with surface using fl at washers.

Assembly

Page 4-5

Cybex Eagle 11070 Arm Curl Owner’s Manual

This page intentionally left blank.

Assembly
Page 4-6

Cybex Eagle 11070 Arm Curl Owner’s Manual

Chapter 5 - Maintenance

All preventive maintenance activities must be performed on a regular basis. Performing
routine preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex
Strength Systems equipment.

NOTE: Cybex is not responsible for performing regular inspection and maintenance actions
for your machines. Instruct all personnel in equipment inspection and maintenance
actions and also in accident reporting/recording. Cybex phone representatives are
available to answer any questions or concerns that you may have.

NOTE: All inspections and
repairs must be
performed by trained
service personnel only.

Cybex will void warranty if
non-Cybex replacement parts
are used.

Daily Procedures

1. Upholstery - Wipe down all upholstery as per the recommendations listed below for light

soiling and more difficult stains.
Light Soiling

• A solution of 10% household liquid dish soap with warm water applied with a soft damp
cloth.

• If necessary, a solution of liquid cleanser and water applied with a soft bristle brush.
Wipe away the residue with a water dampened cloth.

Maintenance

Page 5-1

Cybex Eagle 11070 Arm Curl Owner’s Manual

More Difficult Stains

• Dampen a soft white cloth with a solution of 10% household bleach (sodium hypochlorite), 90%
water. Rub gently. Rinse with a water dampened cloth to remove bleach concentration.

• The same procedure can be used with full strength household bleach, if necessary.

• Allow bleach to puddle on the affected area or apply with a soaked cloth for approximately 30 minutes.
Rinse with a water dampened cloth to remove any remaining bleach concentration.

Alternative Method for Difficult Stains

• Dampen a soft white cloth with rubbing alcohol and rub gently. Rinse with a water dampened cloth to
remove any remaining rubbing alcohol concentration.

NOTE: To restore luster, a light coat of spray furniture wax can be used. Apply for 30 seconds and
follow with a light buffing using a clean white cloth.

Please Review Carefully
When using strong cleaning agents such as rubbing alcohol or bleach, it is advisable to first test in an

inconspicuous area. Other cleaning agents may contain harsh or unknown solvents and are subject to
formula changes by the product manufacturer without notice. Should you desire to use other cleaning
agents, carefully try them in an inconspicuous area to determine potential damage to the material.
Never use harsh solvents or cleaners which are intended for industrial applications. To clean stained or
soiled areas, a soft white cloth is recommended. Avoid use of paper towels.

Cleaning products may be harmful/irritating to your skin, eyes, etc. Use protective gloves and eye
protection. Do not inhale or swallow any cleaning product. Protect surrounding area/clothing from
exposure. Use in a well ventilated area. Follow all product manufacturer’s warnings. CYBEX and its
vendors cannot be held responsible for damage or injuries resulting from the use or misuse of cleaning
products.

2. Frames - Wipe down all frames using a mild solution of warm water and car wash soap. Be sure to dry
thoroughly. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these
could scratch or damage the equipment.

3. Chrome - Clean chrome tubes, first using chrome polish and then using a car wax seal. Neutral
cleaners with a pH between 5.5 and 8.5 are recommended. Be sure to dry thoroughly. AVOID acid or
chlorine based cleaners and also cleaners containing abrasives as these could scratch or damage the
equipment.

Maintenance
Page 5-2

Cybex Eagle 11070 Arm Curl Owner’s Manual

4. Guidelines for cleaning front panel:

• Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing.

• Follow up the application with warm water rinse.

• Don’t use abrasives or high alkaline cleaners.

• Don’t leave cleaners on for long periods, wash immediately.

• Don’t apply cleaners in direct sunlight or at elevated temperatures.

• Don’t use scrapers, squeegees or razors.

• Don’t clean with gasoline.

Compatible Cleaners and Detergents:

• Formula 409

• Top Job

• Joy

• Palmolive

• Windex with Ammonia D

To Minimize Fine or Hairline Scratches:

Mild automotive polish applied and removed with a soft, clean cloth will help fill scratches.

Suggested Polishes:

• Johnson Paste Wax

• Mirror Glaze #10 Plastic Polish (by Mirror Bright Polish Co.)

• Novus Plastics Polish #1, #2 (by Novus Inc.)

Maintenance

Page 5-3

Cybex Eagle 11070 Arm Curl Owner’s Manual

Weekly Procedures

1. Check all nuts and bolts for looseness. Tighten as required.

2. Inspect all belts (entire length) for any

non-uniformity and wear.

Immediately replace belt if any of the following conditions are present:

Maintenance
Page 5-4

Cybex Eagle 11070 Arm Curl Owner’s Manual

3. Some machines use cables in addition to belts. Inspect all cables for wear or damage and proper
tension. When inspecting cables, run your fingers on the cable, paying particular attention to bends

in the cable and attachment points.

Replace all worn cables immediately. The following conditions may indicate a worn

cable:

• A tear or crack in the cable sheath that exposes the cable. See Figure 1.

Figure 1

• A kink in the cable. See Figure 2.

Figure 2

• A curled sheath. See Figure 3.

Figure 3

• “Necking”, a stretched cable sheath. See Figure 4.

Figure 4

Maintenance

Page 5-5

Cybex Eagle 11070 Arm Curl Owner’s Manual

4. Inspect bars and handles for wear, paying particular attention to tab area connecting
points.

Replace all worn handles immediately.

5. Inspect snap links for proper latching (indicates wear).

Replace all worn snap links immediately.

6

. Inspect for loose or worn grips.

Replace all loose or worn grips immediately.

7. Inspect all labeling for readability. This includes instructional placards, warning and caution decals.

Replace all worn labeling immediately.

8.

Inspect all weight stacks for proper alignment and operation.

Correct all improper alignment and operation issues immediately.

9. Wipe Weight Stack Guide Rods clean over entire length. Lubricate with a light coat of medium

weight automotive engine oil.

Yearly Procedures

1. Replace all belts and cables at least annually.

Maintenance
Page 5-6

Cybex Eagle 11070 Arm Curl Owner’s Manual

Environment

Static Electricity - Depending upon where you live, you may experience dry air, causing a common experience of
static electricity. This may be especially true in the winter time. You may notice a static build-up just by walking across a
carpet and then touching a metal object. The same can hold true while working out on your unit. You may experience a
shock due to the build-up of static electricity on your body and the discharge path of the unit. If you experience this type
of situation, you may want to increase the humidity to a comfortable level through the use of a humidifier.

Humidity - The unit is designed to function normally in an environment with a relative humidity range of 30% to 75%.

NOTE: Do not install or use the unit in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor
pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the electronics as
well as other parts of the machine.

Temperature - The unit is designed to function normally in an environment with an ambient
temperature range of 50

Storage

o

F (10o C) to 104o F (40o C) degrees.

Humidity - The unit can be shipped and stored in an environment with a relative humidity range of 10% to 90%.

NOTE: Do not store the unit in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor pool or
outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the electronics as
well as other parts of the machine.

Temperature - The unit can be shipped and stored in an environment with an ambient temperature range of 32
and 140

o

F (60o C) degrees.

o

F (0o C)

Maintenance

Page 5-7

Cybex Eagle 11070 Arm Curl Owner’s Manual

Maintenance
Page 5-8

Cybex Eagle 11070 Arm Curl Owner’s Manual

6 - Service

Please refer to the next several pages for parts lists, exploded-view diagrams.

NOTE: All inspections
and repairs must be
performed by trained
service personnel only.

Cybex will void warranty if
non-Cybex replacement parts
are used.

Service

Page 6-1

Cybex Eagle 11070 Arm Curl Owner’s Manual

This page intentionally left blank

Service
Page 6-2

Cybex Eagle 11070 Arm Curl Owner’s Manual

ARM CURL

PRODUCT NO. 11070

D

L

B

E

H

K

O

C

I

NOTE: See exploded-view diagram for location of J (serial number decal) and N.

F

G

A

DESCRIPTION PART NO.

A. Caution Decal ...................... 4520-362

B. Caution Decal ...................... 8500-026

C. Warning Decal ..................... 4605-381

D. Placard Decal .......................11070-610

E. Eagle Plaque ........................11040-789

F. Arm Pads w/Wear Pad .........4800-119

G. Seat Pad .............................. 4800-172

DESCRIPTION PART NO.

H. Chest Pad ..................... 4800-164

I. Grip ................................ 4605-504

J. Serial Number Decal

K. Wear Cover (Item F) ...... 4800-122

L. Belt .95” ......................... GB000202

M. Weight Selector Pin ...... BH030207

N. Cybex Decal .................. 3900-441

O. Increment Weight Decal. 11000-407

Service

Page 6-3

Cybex Eagle 11070 Arm Curl Owner’s Manual

ITEM QTY PART NO. DESCRIPTION

1 2 11070-340 BUMPER
2 2 08229 PIN,DETENT
3 1 11040-301 CLAMP BLOCK INSERT
4 2 11040-440 KNOB
5 2 11040-750 EXT INC WT CHANNEL
6 2 11040-754 EXTRUDED GUARD
7 2 11040-751 EXT INC WT CHANNEL
8 1 11040-771 COVER, TOP
9 1 11040-768 COVER, TOP
10 2 11040-776 CHASSIS
11 2 11040-777 TRAY, BOTTOM
12 1 11040-775 COVER, PULLEY
13 1 11040-760 PANEL, SHROUD BACK
14 2 11040-762 PANEL, SHROUD FRONT
15 1 11040-560 DECAL, WEIGHT PLATE (10 - 290)
16 1 11050-205 LINK
17 4 11050-375 PIVOT PIN
18 1 11070-200 SEAT FRAME
19 1 11070-201 SEAT BOTTOM LINK
20 1 11070-202 SEAT BOTTOM
21 1 11070-203 INPUT ARM
22 1 11070-204 WEIGHT FRAME
23 2 11070-205 PIVOT HANDLE
24 1 11070-207 CUSHION TUBE
25 1 11070-332 COUNTERWEIGHT
26 1 11070-610-X* PLACARD, EAGLE ARM CURL
27 1 11070-999-X* INSTALLATION INSTRUCTIONS
28 2 11090-359 WT ROD .625 DIA x 42.25
29 1 11090-369 SHAFT, PIVOT
30 4 11090-392 FOOT COVER
31 1 3900-441 DECAL, CYBEX INTERNATIONAL
32 1 4605-381-X* WARNING LABEL
33 1 11100-400 ROTATION DECAL
34 1 4505-331 BUMPER, 1.50 DIA
35 1 4520-362-X* DECAL, CAUTION
36 1 4535-201 PIVOT ARM
37 2 4535-327 PIN, LONG PIVOT
38 1 4535-328 PIN, SHORT PIVOT
39 2 4535-330 TUBE, PIVOT, HANDLE
40 1 4605-511 INSERT,PLASTIC 5.94
41 1 51198 WARRANTY BOOKLET (NOT SHOWN)
42 1 5227-337 DECAL, ADJUSTING
43 2 8500-026-X* DECAL, CAUTION
44 6 BR030214 RETAINING RING, .625 DIA
45 2 BS070201 COM SPRING .56 x .66 1.50 LG
46 1 CM000211 DECAL, PATENT PENDING
47 1 EZ000006-1 GAS SPRING 250N
48 2 FB030232 BEARING, RADIAL 17 mm EXT RACE
49 10 FB130205 BRG,FLG .62 x .75 .38 LG
50 8 FB130207 BRG FLG 17mm X 19mm X 25mm

*Language Key

ITEM QTY PART NO. DESCRIPTION

51 64” GB000202 BELT .95 WIDE
52 2 GP000209 PULLEY ASSEMBLY-3.50
53 3 HC700415 BHSCS .375-16 X .75
54 12 HC700417 BHSCS .375-16 X 1.00
55 2 HC700428 BHSCS .375-16 X 2.25
56 4 HC700432 BHSCS .375-16 X 2.75
57 10 HF540200 GROMMET, NYLON
58 2 HN-60065 NUT, HEX SELF- LOCKING .312-18 BLK
ZINC
59 8 HN704901 LOCKNUT, .375-16 NYLON
60 2 HP286716 GROOVE PIN, .188 X .750
61 9 HS347600 WASHER, SAE .375
62 1 HS347702 WASHER, FLAT .387 ID x 1.753 OD X .06
THK
63 2 HS407100 WASHER, SPRING .650 ID x .790 OD x
.062 THK
64 4 HT102214 PHIL, HEX, WASHER HD, TYPE 23,
10-24
65 18 HT542514 PN HD PHIL SC # 8 X .625 BLK
66 2 HX-60184 BALL STUD, .312 - 18 UNC x 10 mm
67 2 HY740000 SET SCREW
68 10 JC700412 BHSCS .375-16 X .50
69 4 JC700420 BHSCS .375-16 X 1.25
70 2 JS407100 BUSHING .625 MACHINERY
71 1 PN660200 INSERT, PLASTIC 1.00 DIA-11 GA
72 1 PP090206 INSERT, PLASTIC 2.00 x 3.00 x 11 GA
73 1 PP090210 INSERT, PL 2.00 SQ X 10-14 GA
74 1 PP090211 INSERT, PL 1.50 SQ X 10-14 GA
75 2 PR060005 BUMPER, WEIGHT
76 2 4605-504 GRIP 1.38 OD X .96 ID
77 1 PR060006 BUMPER, RECESS
78 2 PR250203 STRIP, FOAM .12 X .25 X ROLL
79 1 11000-394 DECAL, INDICATOR
80 1 11070-337 DECAL, SEAT ADJUSTING
81 8 JS347400 LOCKWASHER, INT TOOTH .375
82 1 HT512517 TAP SC 10-24 X 1.00 TYPE WB PN HD
PHIL BLK
83 1 11040-789 EAGLE PLAQUE
84 4 HN575100 LOCKNUT .190-No 10-24
85 4 HT572512 TAP SC NO. 10-24 X .50 PN HD PHIL
86 1 4800-172 SEAT PAD
87 1 4800-164 CHSET PAD
88 2 4800-119 ARM PAD W/WEAR PAD
89 2 4800-122 WEAR PAD COVER
90 1 13000-402 MOUNT, WATER BOTTLE HOLDER
91 1 13000-400 HOLDER, WATER BOTTLE
92 1 HT552515 TAP SC NO 8-16X.75
93 2 HT512517 TAP SC 10-24 X 1.00 TYPE WB
94 1 11000-407-X* DECAL, INCREMENT WARNING
95 2 JC620410 BHSCS .250-20 X .375
96 1 11040-790 DECAL, MADE IN USA

1-German
2-French
3-Spanish
English
6-Japanese
7-Swedish
8-Russian

Service
Page 6-4

Cybex Eagle 11070 Arm Curl Owner’s Manual

2

ARM CURL MAIN ASSEMBLY DETAIL

39

23

76

49

54

36

37

54

49

49

54

38

44

40

1

95

88

49

70

73

60

1

43

49

33

49

69

68

54

89

95

48

62

54

34

53

21

29

42

25

59

67

3

52

59

52

55

22

59

90

9

50

19

58

4

47

16

66

45

50

72

2

45

30

86

81

58

74

20

81

54

77

82

66

18

81

56

4

17

61

68

79

68

61

2

71

80

53

17

87

24

64

30

54

46

93

59

30

Service

Page 6-5

Cybex Eagle 11070 Arm Curl Owner’s Manual

SHROUD AND GUIDE ROD ASSEMBLY DETAIL

85

83

26

12

8

65

9

84

63

44

65

78

44

51

31

5

28

7

94

14

6

75

28

13

7

96

6

65

11

65

32

14

5

75

65

11

65

Service
Page 6-6

Cybex Eagle 11070 Arm Curl Owner’s Manual

BELT ROUTING DETAIL

51

Service

Page 6-7

Cybex Eagle 11070 Arm Curl Owner’s Manual

ARM CURL TOP WEIGHT ASSEMBLY

ITEM QTY PART NO. DESCRIPTION

1 1 11040-366 Top Weight Assembly, Molded
2 1 11040-367 Hub, Molded
3 2 11040-369 Rod, Linkage
4 2 11040-370 Pin
5 1 11040-427 Rod
6 1 11040-426 Stem
7 1 11040-424 Cover Plate
8 1 11040-416 Cover, Top Weight
9 1 11040-425 Knob
10 1 BH030207 Pin, Weight Selector
11 1 4700-250 Lifting Post 10
12 4 BR030209 External Retaining Ring .188
13 2 BR030220 Internal Retaining Ring 1.250
14 1 HP016820 Cotter Pin .125 X 1.25
15 1 HP266765 Roll Pin, .125 X .938

23

22

8

ITEM QTY PART NO. DESCRIPTION

16 2 HS720004 Felt Washer, .641 1.250 .125 T
17 4 HT562715 Tap SC NO 10 x .750 F Phil
18 4 HT582510 Tap SC NO 10 x .375 PN HD Phil
19 2 11040-409 Molded Bumper Pad
20 12 11040-572 Guard, Increment Weight
21 6 11040-573 Weight Increment
22 1 11040-216 Belt Clamp
23 1 11040-301 Clamp Block Insert
24 1 11040-428 Adjustment Decal
25 1 11040-429 Rotation Decal
26 1 HT552512 Screw, Pan HD Phil HD Self
Tapping 8-16 x .50, Type WB
27 3 HY740000 Set Screw
28 9 4000C101 Weight Stack Plate
29 1 4701-011 Weight Pack (Not Shown)

27

TOURQUE SET SCREWS
300-350 IN./LBS

12

2

3

12

14

13

16

1

4

21

3

4

5

15

26

6

24

20

17

NOTE: Increment weights are located

7

18

10

9

25

in the increment weight channel.

19

11

See main assembly.

Service
Page 6-8

28

10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX [phone]

www.cybexinternational.com • [e-mail]