CyberResearch CPGN CQ-30-X, CPGN CQ-26-X, CPGN C2-30-X, CPGN PE-29-X User Manual

Download

CPGN CQ-30-X

3.0 MHz Intel® Core™2 Quad

CPGN CQ-26-X

2.6 MHz Intel® Core™2 Quad

CPGN C2-30-X

3.0 MHz Intel® Core™2 Duo

CPGN PE-29-X

2.9 MHz Pentium® Dual Core

CPGN CPU Card

with with with with

No part of this manual may be reproduced without permission.

25 Business Park Drive, Branford, CT 06405

203-643-5000 (9

USER’S MANUAL

VERSION 1.0 • June 2011

CyberResearch, Inc.

www.cyberresearch.com

AM - 5PM EST) FAX: 203-643-5001

CPGN CPU Card

Revision

Date Version Changes

14 June, 2011 1.0

CPGN CPU Card

June, 2011

The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of CyberResearch, Inc.

In no event will CyberResearch, Inc. be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of CyberResearch, Inc.

Trademarks

“CyberResearch®” is a trademark of CyberResearch, Inc. Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

NOTICE

CyberResearch, Inc. does not authorize any CyberResearch product for use in life support systems, medical equipment, and/or medical devices without the written approval of the President of CyberResearch, Inc. Life support devices and systems are devices or systems which are intended for surgical implantation into the body, or to support or sustain life and whose failure to perform can be reasonably expected to result in injury. Other medical equipment includes devices used for monitoring, data acquisition, modification, or notification purposes in relation to life support, life sustaining, or vital statistic recording. CyberResearch products are not designed with the components required, are not subject to the testing required, and are not submitted to the certification required to ensure a level of reliability appropriate for the treatment and diagnosis of humans.

Table of Contents

1 INTRODUCTION........................................................................................................ 13

1.1 INTRODUCTION......................................................................................................... 14

1.2 BENEFITS ................................................................................................................. 14

1.3 FEATURES ................................................................................................................14

1.4 CONNECTORS ........................................................................................................... 15

1.5 DIMENSIONS............................................................................................................. 16

1.6 DATA FLOW ............................................................................................................. 17

1.7 TECHNICAL SPECIFICATIONS.................................................................................... 18

2 PACKING LIST........................................................................................................... 20

2.1 ANTI-STATIC PRECAUTIONS ..................................................................................... 21

2.2 UNPACKING PRECAUTIONS ...................................................................................... 21

2.3 PACKING LIST .......................................................................................................... 22

3 CONNECTORS ........................................................................................................... 24

3.1 PERIPHERAL INTERFACE CONNECTORS .................................................................... 25

3.1.1 Layout .............................................................................................................. 25

3.1.2 Peripheral Interface Connectors ..................................................................... 25

3.1.3 External Interface Panel Connectors............................................................... 26

3.2 INTERNAL PERIPHERAL CONNECTORS...................................................................... 26

3.2.1 ATX Power Control Connector........................................................................ 26

3.2.2 Audio Kit Connector ........................................................................................ 27

3.2.3 Battery Connector............................................................................................ 28

3.2.4 CPU Fan Connector ........................................................................................ 29

3.2.5 CPU Power Input Connector........................................................................... 29

3.2.6 DVI Connector................................................................................................. 30

3.2.7 Digital I/O Connector...................................................................................... 31

3.2.8 Floppy Disk Connector.................................................................................... 32

3.2.9 Front Panel Connector .................................................................................... 34

3.2.10 Infrared Interface Connector......................................................................... 35

3.2.11 Keyboard Connector...................................................................................... 35

CPGN CPU Card

3.2.12 Memory Slot................................................................................................... 36

3.2.13 IDE Connector............................................................................................... 37

3.2.14 Parallel Port Connector ................................................................................ 38

3.2.15 SATA Drive Connectors................................................................................. 39

3.2.16 Serial Port Connector.................................................................................... 40

3.2.17 SPI Flash Connector...................................................................................... 41

3.2.18 USB Connectors............................................................................................. 42

3.3 EXTERNAL PERIPHERAL INTERFACE CONNECTOR PANEL ........................................ 42

3.3.1 Keyboard/Mouse Connector............................................................................ 43

3.3.2 LAN Connector ................................................................................................ 44

3.3.3 USB Connector ................................................................................................ 44

3.3.4 VGA Connector................................................................................................ 45

4 INSTALLATION......................................................................................................... 46

4.1 ANTI-STATIC PRECAUTIONS ..................................................................................... 47

4.2 INSTALLATION CONSIDERATIONS............................................................................. 47

4.3 BASIC INSTALLATION............................................................................................... 48

4.3.1 CPU Installation.............................................................................................. 49

4.3.2 DIMM Installation ........................................................................................... 51

4.3.3 Backplane Installation ..................................................................................... 52

4.3.4 CPU Card Installation..................................................................................... 53

4.4 JUMPER SETTINGS .................................................................................................... 53

4.4.1 Clear CMOS Jumper........................................................................................ 54

4.5 INTERNAL PERIPHERAL DEVICE CONNECTIONS........................................................ 54

4.5.1 SATA Drive Connection................................................................................... 54

4.5.2 USB Cable (Dual Port) with Slot Bracket ....................................................... 56

4.6 EXTERNAL PERIPHERAL INTERFACE CONNECTION................................................... 57

4.6.1 LAN Connection............................................................................................... 57

4.6.2 USB Device Connection................................................................................... 58

4.6.3 VGA Monitor Connection ................................................................................ 59

4.7 SOFTWARE INSTALLATION ....................................................................................... 60

5 BIOS.............................................................................................................................. 63

5.1 INTRODUCTION......................................................................................................... 64

5.1.1 Starting Setup................................................................................................... 64

5.1.2 Using Setup...................................................................................................... 64

5.1.3 Getting Help..................................................................................................... 65

5.1.4 Unable to Reboot after Configuration Changes.............................................. 65

5.1.5 BIOS Menu Bar................................................................................................ 65

5.2 MAIN........................................................................................................................ 66

5.3 ADVANCED .............................................................................................................. 67

5.3.1 CPU Configuration.......................................................................................... 68

5.3.2 IDE Configuration ........................................................................................... 69

5.3.2.1 IDE Master, IDE Slave ............................................................................. 71

5.3.3 Floppy Configuration....................................................................................... 75

5.3.4 Super IO Configuration.................................................................................... 76

5.3.5 Hardware Health Configuration...................................................................... 80

5.3.6 Power Configuration ....................................................................................... 83

5.3.6.1 ACPI Settings............................................................................................ 83

5.3.6.2 APM Configuration .................................................................................. 84

5.3.7 Remote Access Configuration.......................................................................... 86

5.3.8 USB Configuration........................................................................................... 88

5.4 PCI/PNP................................................................................................................... 90

5.5 BOOT........................................................................................................................ 93

5.5.1 Boot Settings Configuration............................................................................. 93

5.5.2 Boot Device Priority ........................................................................................ 95

5.5.3 Hard Disk Drives............................................................................................. 96

5.5.4 Removable Drives............................................................................................ 96

CD/DVD Drives........................................................................................................ 97

5.6 SECURITY................................................................................................................. 97

5.7 CHIPSET ................................................................................................................... 98

5.7.1 Northbridge Configuration.............................................................................. 99

5.7.1.1 Video Function Configuration................................................................ 101

5.7.2 Southbridge Configuration ............................................................................ 101

5.8 EXIT....................................................................................................................... 102

A BIOS OPTIONS........................................................................................................ 104

B TERMINOLOGY...................................................................................................... 108

C WATCHDOG TIMER ............................................................................................. 112

D DIGITAL I/O INTERFACE.................................................................................... 115

CPGN CPU Card

D.1 INTRODUCTION...................................................................................................... 116

D.2 DIO CONNECTOR PINOUTS ................................................................................... 116

D.3 ASSEMBLY LANGUAGE EXAMPLE ......................................................................... 116

E HAZARDOUS MATERIALS DISCLOSURE....................................................... 117

E.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS

ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY..................................... 118

List of Figures

Figure 1-1: CPGN CPU C a rd (SBC)............................................................................................14

Figure 1-2: Connectors ...............................................................................................................15

Figure 1-3: Dimensions (m m) .....................................................................................................16

Figure 1-4: Data Flow Diagram...................................................................................................17

Figure 3-1: Connectors and Jumpers........................................................................................25

Figure 3-2: ATX Power Supply Enable Connector Location ...................................................27

Figure 3-3: Audio Kit Connecto r L ocation................................................................................28

Figure 3-4: Battery Connector Lo catio n....................................................................................28

Figure 3-5: CPU Fan Conn ecto r L o c atio n .................................................................................29

Figure 3-6: CPU Power Input Connector Location...................................................................30

Figure 3-7: DVI Connector Locatio n ..........................................................................................31

Figure 3-8: Digital I/O Connector Lo catio ns.............................................................................32

Figure 3-9: Floppy Drive Connector Location ..........................................................................33

Figure 3-10: Front Panel Con n ecto r L o c atio n ..........................................................................34

Figure 3-11: Infrared Connector Locatio n.................................................................................35

Figure 3-12: Keyboard Connector Location..............................................................................36

Figure 3-13: Memory Card S lo t L o catio n ..................................................................................37

Figure 3-14: IDE Connector Location........................................................................................37

Figure 3-15: Parallel Port Connector L o c atio n .........................................................................39

Figure 3-16: SATA Drive Connector Lo catio n ..........................................................................40

Figure 3-17: Serial Port Connector Location............................................................................40

Figure 3-18: SPI Flash Connector..............................................................................................41

Figure 3-19: USB Connector Pinout Locations ........................................................................42

Figure 3-20: External Peripheral Interface Connector .............................................................43

Figure 3-21: PS/2 Pinout and Configuration.............................................................................43

Figure 3-22: VGA Connector ......................................................................................................45

Figure 4-1: Intel LGA775 Socket ................................................................................................49

Figure 4-2: Remove Protective Cover .......................................................................................50

Figure 4-3: CPU Socket Load P late ............................................................................................50

Figure 4-4: Insert the Socket LGA775 CPU...............................................................................51

Figure 4-5: DIMM Installation......................................................................................................52

CPGN CPU Card

Figure 4-6: Clear BIOS Jumper Lo catio n ..................................................................................54

Figure 4-7: SATA Drive Cable C o n nection................................................................................55

Figure 4-8: SATA Power D riv e C o n n ectio n...............................................................................56

Figure 4-9: Dual USB Cable C o n n ection...................................................................................57

Figure 4-10: LAN Connection.....................................................................................................58

Figure 4-11: USB Device Connection........................................................................................59

Figure 4-12: VGA Connector ......................................................................................................60

Figure 4-13: Introduction Screen...............................................................................................61

Figure 4-14: Available Drivers....................................................................................................61

Figure 4-15: Choose drivers to install.......................................................................................62

List of Tables

Table 1-1: Technical Specifications...........................................................................................19

Table 2-1: Packing List................................................................................................................23

Table 3–1: Internal Peripheral Connectors ...............................................................................26

Table 3–2: External Peripheral Connectors..............................................................................26

Table 3-3: ATX Power Supply Enable Connector Pinouts.......................................................27

Table 3-4: Audio Kit Connector Pinouts....................................................................................28

Table 3-5: Battery Connector Pinouts.......................................................................................29

Table 3-6: CPU Fan Connector Pinouts.....................................................................................29

Table 3-7: CPU Power Input Connector Pinouts ......................................................................30

Table 3-8: DVI Connector Pinouts..............................................................................................31

Table 3-9: Digital I/O Connector Pinouts ...................................................................................32

Table 3-10: Floppy Drive Connector Pinouts............................................................................33

Table 3-11: Front Panel Connector Pinouts..............................................................................34

Table 3-12: Infrared Connector Pinouts....................................................................................35

Table 3-13: Keyboard Connector Pinouts.................................................................................36

Table 3-14: IDE Connector Pinouts............................................................................................38

Table 3-15: Parallel Port Connector Pinouts.............................................................................39

Table 3-16: Serial Port Connector Pinouts................................................................................41

Table 3-17: SPI Flash Connector................................................................................................41

Table 3-18: USB Port Connector Pinouts..................................................................................42

Table 3-19: Keyboard Connector Pinouts.................................................................................44

Table 3-20: LAN Pinouts.............................................................................................................44

Table 3-21: USB Port Pinouts.....................................................................................................45

Table 3-22: VGA Connector Pinouts..........................................................................................45

Table 4-1: Jumpers......................................................................................................................53

Table 4-2: Clear BIOS Jumper Settin g s.....................................................................................54

Table 5-1: BIOS Navigation K e y s...............................................................................................65

CPGN CPU Card

BIOS Menus

BIOS Menu 1: Main......................................................................................................................66

BIOS Menu 2: Advan ced.............................................................................................................68

BIOS Menu 3: CPU C o nfiguration..............................................................................................68

BIOS Menu 4: IDE Co n fig u r atio n................................................................................................69

BIOS Menu 5: IDE Master and ID E Slave Configuration..........................................................71

BIOS Menu 6: IDE Master and ID E Slave Configuration..........................................................76

BIOS Menu 7: Super IO Configuration.......................................................................................77

BIOS Menu 8: Hardwa re Health Configuration.........................................................................80

BIOS Menu 9: ACPI C o nfiguration.............................................................................................83

BIOS Menu 10: ACPI S e ttings....................................................................................................83

BIOS Menu 11: APM C onfiguration............................................................................................84

BIOS Menu 12: Remote Access Configuration.........................................................................86

BIOS Menu 13: USB C o n f ig u ration............................................................................................89

BIOS Menu 14: PCI/Pn P Configuration......................................................................................91

BIOS Menu 15: Boot....................................................................................................................93

BIOS Menu 16: Boot S ettings Configuration............................................................................93

BIOS Menu 17: Boot De v ice Priority Settings...........................................................................95

BIOS Menu 18: Hard Disk D r iv es ...............................................................................................96

BIOS Menu 19: Remo v a b le D riv es.............................................................................................96

BIOS Menu 20: CD/DV D Drives..................................................................................................97

BIOS Menu 21: Security..............................................................................................................97

BIOS Menu 22: Chipset...............................................................................................................99

BIOS Menu 23:Northbrid g e Chipset Configuration..................................................................99

BIOS Menu 24:Northbrid g e Chipset Configuration................................................................101

BIOS Menu 25: Southb rid g e Chipset Configuration..............................................................102

BIOS Menu 26: Exit....................................................................................................................103

Chapter

1 Introduction

CPGN CPU Card

1.1 IIntroduction

1.2 BBenefits

1.3 FFeatures

Figure 1-1: CPGN CPU Card (SBC)

The CPGNis a PCIMG 1.0 CPU card with a 800/1066/1333 MHz front side bus (depending on the CPU chosen). The LGA775 socket accepts Intel® Core™2 Duo/Quad/Extreme processors and Pentium two DDR3 DIMMs up to 2.0 GB each (4.0 GB total). The CPGN includes VGA video output and an optional DVI output. Expansion cards may be added to the expansion card slots on the backplane. Other features include floppy disk connector, IDE connector, 4 x SATA, dual Gigabit LAN, digital I/O, two serial ports, one parallel port and seven USB ports.

Some of the CPGN CPU card’s benefits include:

 Powerful graphics  Staying connected with both wired LAN connections  Speedy running of multiple programs and applications

Some of the CPGN motherboard features are listed below:

dual-core processors. The card supports

 PCIMG 1.0  RoHS compliant  LGA775 CPU socket

 Supports two DDR3 DIMMs

1.4 CConnectors

 Two Gigabit Ethernet connectors  Four SATA connectors  High Definition audio connects to an optional audio kit

The connectors on the CPGN are shown in the figure below.

Figure 1-2: Connectors

CPGN CPU Card

1.5 DDimensions

The main dimensions of the CPGN are shown in the diagram below.

Figure 1-3: Dimensions (mm)

1.6 DData Flow

852HFigure 1-4 shows the data flow between the system chipset, the CPU and other

components installed on the motherboard.

Figure 1-4: Data Flow Diagram

CPGN CPU Card

1.7 TTechnical Specifications

Specification

CPGN Form Factor CPUs Supported

Front Side Bus (FSB) Northbridge Chipset Integrated Graphics

Memory Southbridge Chipset BIOS Digital I/O Ethernet Controllers Super I/O Controller Watchdog Timer Audio Connectors Keyboard/Mouse Serial Ports USB 2.0/1.1 ports Floppy Disk Drives IDE Serial ATA

CPGN technical specifications are shown below.

PCIMG 1.0 Socket LGA775 Intel® Core™2 Duo/Quad/E xtrem e ,

Pentium Dual Core, Celeron 800/1066/1333 MHz Intel® G41 VGA

DVI Two DDR3 modules up to 2 GB each (4 GB total) Intel® ICH7 AMI BIOS 8-bit, 4-bit input/4-bit output Dual Realtek RTL8111CP iTE IT8718F Software programmable supports 1~255 sec. system reset One internal audio connector One external PS/2, one internal pin header Two RS-232 COM connectors Six internal via pin header. One external One floppy disk drive (FDD) connector One IDE connector Four independent SATA channels with 3.0 Gb/s data

transfer rates

Environmental and Power Specifications

Power Supply Power Consumption

Operating temperature

Humidity Physical Specifications Dimensions Gross Weight

Table 1-1: Technical Specifications

ATX supported 5 V @ 7.13 A

12 V @ 0.27 A 5VBS @ 0.11 A Vcore @ 3.02 A 3D Mark2001SE with Intel® Core™2 Duo E8500

3.16GHz and two 2GB DDR3 modules 0ºC ~ 60ºC( 32°F ~ 140°F), requires cooler and

silicone heat sink paste 5% ~ 95% (noncondensing)

338 mm x 122 mm

1.1 kg

CPGN CPU Card

Chapter

2 Packing List

2.1 AAnti-static Precautions

WARNING!

2.2 UUnpacking Precautions

Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user.

Make sure to adhere to the following guidelines:

 Wear an anti-static wristband: Wearing an anti-static wristband can prevent

electrostatic discharge.

 Self-grounding: Touch a grounded conductor every few minutes to

discharge any excess static buildup.

 Use an anti-static pad: When configuring any circuit board, place it on an

anti-static mat.

 Only handle the edges of the PCB: Don't touch the surface of the

motherboard. Hold the motherboard by the edges when handling.

When the CPGN is unpacked, please do the following:

 Follow the antistatic guidelines above.  Make sure the packing box is facing upwards when opening.  Make sure all the packing list items are present.

CPGN CPU Card

2.3 PPacking List

NOTE:

Quantity

Part Number or Description

Image

The CPGN is shipped with the following components:

1 Error! Unknown document property

If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact your CyberResearch applications engineer or email sales@cyberresearch.com.

name.

1 Dual DB-9 cable (with end plate)

4 SATA cable

1 Keyboard and mouse Y cable

1 Dual USB cable (with end plate)

1 IO-KIT (with end plate)

1 Mini jumper pack (2.0mm)

Quantity

Part Number or Description

Image

1 Drivers and Utility Disk

Table 2-1: Packing List

CPGN CPU Card

Chapter

3 Connectors

3.1 PPeripheral Interface Connectors

3.1.1 LLayout

3.1.2 PPeripheral Interface Connectors

Connector

Type

Label

This chapter details all the jumpers and connectors.

The figure below shows all the connectors and jumpers.

Figure 3-1: Connectors and Jumpers

The table below lists all the connectors on the board.

ATX Power Control Connector 3-pin wafer (1x3) ATXCTL1 Audio Kit Connector 9-pin header J_AUDIO1 Battery Connector 2-pin wafer (1x2) BAT1 CPU Fan Connector 4-pin header CPU_FAN1 CPU Power Input Connector 4-pin connector CPU12V1 DVI Connector 26-pin header DVI1 Digital I/O Connector 10-pin header DIO1 Floppy Disk Connector 34-pin header FDD1 Front Panel Connector 14-pin header F_PANEL1

CPGN CPU Card

Connector

Type

Label

3.1.3 EExternal Interface Panel Connectors

Connector

Type

Label

3.2 IInternal Peripheral Connectors

3.2.1 AATX Power Control Connector

CN Label:

ATXCTL1

Infrared Interface Connector 5-pin header (1x5) IR1 Keyboard Connector 5-pin header (1x5) KB1 Memory Slot DIMM slot DIMM1, DIMM2 IDE Connector 40-pin box header PIDE1 Parallel Port Connector 26-pin box header LPT1 SATA Drive Connectors 7-pin SATA drive

connectors Serial Port Connector 10-pin box header COM1, COM2 SPI Flash Connector 8-pin header JSPI1 USB Connectors 8-pin header USB12, USB34,

Table 3–1: Internal Peripheral Connectors

The table below lists the connectors on the external I/O panel.

Keyboard/Mouse Connector PS/2 KB_MS1 LAN Connector RJ-45 LAN1, LAN2 USB Connector USB port USB_C1

SATA1, SATA2, SATA3, SATA4

USB56

VGA Connector 15-pin Female VGA1

Table 3–2: External Peripheral Connectors

The section describes all of the connectors on the CPGN.

CN Type: CN Location: CN Pinouts:

3.2.2 AAudio Kit Connector

CN Label:

J_AUDIO1 CN Type: CN Location: CN Pinouts:

3-pin wafer (1x3) See Figure 3-2 See Table 3-3

The connector is for enabling an ATX power supply. When connected to the power supply, the power can be turned on and off with the front panel switch.

Figure 3-2: ATX Power Supply Enable Connector Location

Pin Description

1 GND 2 ATX_ON 3 5VSB

Table 3-3: ATX Power Supply Enable Connector Pinouts

9-pin header See Figure 3-3 See Table 3-4

This connector connects to an external audio kit.

CPGN CPU Card

3.2.3 BBattery Connector

CN Label:

BAT1 CN Type: CN Location: CN Pinouts:

Figure 3-3: Audio Kit Connector Location

Pin Description Pin Description

1 SYNC 2 BITCLK 3 SDOUT 4 PCBEEP 5 SDIN 6 RST# 7 VCC 8 GND 9 +12 V

Table 3-4: Audio Kit Connector Pinouts

2-pin wafer (1x2) See Figure 3-4 See Table 3-5

This is connected to the system battery. The battery provides power to the system clock to retain the time when power is turned off.

Figure 3-4: Battery Connector Location

Pin Description

1 Battery+

3.2.4 CCPU Fan Connector

CN Label:

CPU_FAN1 CN Type: CN Location: CN Pinouts:

3.2.5 CCPU Power Input Connector

CN Label:

CPU12V1 CN Type:

Pin Description

2 Ground

Table 3-5: Battery Connector Pinouts

4-pin header See Figure 3-5 See Table 3-6

The fan connector attaches to a CPU cooling fan.

Figure 3-5: CPU Fan Connector Location

Pin Description

1 GND 2 +12 V 3 Rotation signal 4 Control

Table 3-6: CPU Fan Connector Pinouts

4-pin connector

CPGN CPU Card

CN Location: CN Pinouts:

3.2.6 DDVI Connector

CN Label:

DVI1 CN Type: CN Location: CN Pinouts:

See Figure 3-6 See Table 3-7

The CPU power input connector provides power to the CPU.

Figure 3-6: CPU Power Input Connector Location

Pin Description

1 GND 2 GND 3 12 V 4 12 V

Table 3-7: CPU Power Input Connector Pinouts

26-pin header See Figure 3-7 See Table 3-8

The DVI connector connects to a monitor that supports DVI video input.

3.2.7 DDigital I/O Connector

CN Label:

DIO1 CN Type: CN Location: CN Pinouts:

Figure 3-7: DVI Connector Location

Pin Description Pin Description

1 Data 2- 14 +5 V Power 2 Data 2+ 15 GND 3 GND 16 Hot Plug Detect 4 N/C 17 Data05 N/C 18 Data 0+ 6 DDC Clock 19 GND 7 DDC Data 20 N/C 8 N/C 21 N/C 9 Data 1- 22 GND 10 Data 1+ 23 Clock+ 11 GND 24 Clock12 N/C 25 GND 13 N/C 26

Table 3-8: DVI Connector Pinouts

10-pin header See Figure 3-8 See Table 3-9

CPGN CPU Card

3.2.8 FFloppy Disk Connector

CN Label:

FDD1 CN Type: CN Location: CN Pinouts:

The digital I/O connector provides programmable input and output for external devices. The digital I/O provides 4-bit output and 4-bit input.

Figure 3-8: Digital I/O Connector Locations

Pin Description Pin Description

1 GND 2 VCC 3 Output 3 4 Output 2 5 Output 1 6 Output 0 7 Input 3 8 Input 2 9 Input 1 10 Input 0

Table 3-9: Digital I/O Connector Pinouts

34-pin header See Figure 3-9 See Table 3-10

The floppy disk connector is connected to a floppy disk drive.

Figure 3-9: Floppy Drive Connector Location

Pin Description Pin Description

1 GND 2 REDUCE WRITE 3 GND 4 N/C 5 N/C 6 N/C 7 GND 8 INDEX# 9 GND 10 MOTOR ENABLE A# 11 GND 12 DRIVE SELECT B# 13 GND 14 DRIVE SELECT A# 15 GND 16 MOTOR ENABLE B# 17 GND 18 DIRECTION# 19 GND 20 STEP# 21 GND 22 WRITE DATA# 23 GND 24 WRITE GATE# 25 GND 26 TRACK 0# 27 GND 28 WRITE PROTECT# 29 GND 30 READ DATA# 31 GND 32 SIDE 1 SELECT# 33 GND 34 DISK CHANGE#

Table 3-10: Floppy Drive Connector Pinouts

CPGN CPU Card

3.2.9 FFront Panel Connector

CN Label:

F_PANEL1 CN Type: CN Location: CN Pinouts:

14-pin header See Figure 3-10 See Table 3-11

The front panel connector connects to the indicator LEDs and buttons on the computer's front panel.

Figure 3-10: Front Panel Connector Location

Pin Description Pin Description

1 Power LED+ 2 Speaker+ 3 N/C 4 N/C 5 Power LED- 6 N/C 7 Power button+ 8 Speaker9 Power button- 10 N/C 11 HDD LED+ 12 Reset+ 13 HDD LED- 14 Reset-

Table 3-11: Front Panel Connector Pinouts

3.2.10 IInfrared Interface Connector

CN Label:

IR1 CN Type: CN Location: CN Pinouts:

3.2.11 KKeyboard Connector

CN Label:

KB1 CN Type: CN Location: CN Pinouts:

5-pin header (1x5) See Figure 3-11 See Table 3-12

The infrared connector attaches to an infrared receiver for use with remote controls.

Figure 3-11: Infrared Connector Location

Pin Description

1 VCC 2 NC 3 IR-RX 4 GND 5 IR-TX

Table 3-12: Infrared Connector Pinouts

5-pin header (1x5) See Figure 3-12 See Table 3-13

CPGN CPU Card

3.2.12 MMemory Slot

CN Label:

DIMM1, DIMM2 CN Type: CN Location:

The keyboard connector can be used to install a PS/2 keyboard.

Figure 3-12: Keyboard Connector Location

Pin Description

1 KEYBOARD CLOCK 2 KEYBOARD DATA 3 N/C 4 GROUND 5 VCC

Table 3-13: Keyboard Connector Pinouts

DIMM slot See Figure 3-13791H

The DIMM slots are for DIMM memory modules.

3.2.13 IIDE Connector

CN Label:

PIDE1 CN Type: CN Location: CN Pinouts:

Figure 3-13: Memory Card Slot Location

40-pin box header See Figure 3-14 See Table 3-14

Connects to IDE hard drives and optical drives.

Figure 3-14: IDE Connector Location

Pin Description Pin Description

1 RESET# 2 GROUND

CPGN CPU Card

3.2.14 PParallel Port Connector

CN Label:

LPT1 CN Type: CN Location: CN Pinouts:

Pin Description Pin Description

3 DATA 7 4 DATA 8 5 DATA 6 6 DATA 9 7 DATA 5 8 DATA 10 9 DATA 4 10 DATA 11 11 DATA 3 12 DATA 12 13 DATA 2 14 DATA 13 15 DATA 1 16 DATA 14 17 DATA 0 18 DATA 15 19 GROUND 20 N/C 21 IDE DRQ 22 GROUND 23 IOW# 24 GROUND 25 IOR# 26 GROUND 27 IDE CHRDY 28 GROUND 29 IDE DACK 30 GROUND–DEFAULT 31 INTERRUPT 32 N/C 33 SA1 34 N/C 35 SA0 36 SA2 37 HDC CS0# 38 HDC CS1# 39 HDD ACTIVE# 40 GROUND

Table 3-14: IDE Connector Pinouts

26-pin box header See Figure 3-15 See Table 3-15

The parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer.

3.2.15 SSATA Drive Connectors

CN Label:

SATA1, SATA2, SATA3, SATA4 CN Type: CN Location:

Figure 3-15: Parallel Port Connector Location

Pin Description Pin Description

1 STROBE# 14 AUTO FORM FEED# 2 DATA0 15 ERROR# 3 DATA1 16 INITIALIZE# 4 DATA2 17 PRINTER SELECT LN# 5 DATA3 18 GROUND 6 DATA4 19 GROUND 7 DATA5 20 GROUND 8 DATA6 21 GROUND 9 DATA7 22 GROUND 10 ACKNOWLEDGE 23 GROUND 11 BUSY 24 GROUND 12 PAPER EMPTY 25 GROUND 13 PRINTER SELECT

Table 3-15: Parallel Port Connector Pinouts

The SATA drive connectors can be connected to SATA drives.

7-pin SATA drive connectors See Figure 3-16

CPGN CPU Card

3.2.16 SSerial Port Connector

CN Label:

COM1, COM2 CN Type: CN Location: CN Pinouts:

Figure 3-16: SATA Drive Connector Location

10-pin box header See Figure 3-17 See Table 3-16

This connector provides RS-232 communications.

Figure 3-17: Serial Port Connector Location

Pin Description

1 Data Carrier Direct (DCD) 2 Receive Data (RXD)

3.2.17 SSPI Flash Connector

CN Label:

JSPI1 CN Type: CN Location: CN Pinouts:

Pin Description

3 Transmit Data (TXD) 4 Data Terminal Ready (DTR) 5 Ground (GND) 6 Data Set Ready (DSR) 7 Request To Send (RTS) 8 Clear To Send (CTS) 9 Ring Indicator (RI) 10 NC

Table 3-16: Serial Port Connector Pinouts

8-pin header See Figure 3-18 See Table 3-17

The 8-pin SPI Flash connector is used to flash the BIOS.

Figure 3-18: SPI Flash Connector

Pin Description Pin Description

1 VCC 2 GND 3 CS# 4 CLOCK 5 SO 6 SI 7 NC 8 NC

Table 3-17: SPI Flash Connector

CPGN CPU Card

3.2.18 UUSB Connectors

CN Label:

USB12, USB34, USB56 CN Type: CN Location: CN Pinouts:

3.3 EExternal Peripheral Interface Connector Panel

8-pin header See Figure 3-19 See Table 3-18

The USB connectors connect to USB devices. Each pin header provides two USB ports.

Figure 3-19: USB Connector Pinout Locations

Pin Description Pin Description

1 VCC 2 GND 3 DATA1- 4 DATA2+ 5 DATA1+ 6 DATA27 GND 8 VCC

Table 3-18: USB Port Connector Pinouts

The figure below shows the external peripheral interface connector (EPIC) panel. The EPIC panel consists of the following:

3.3.1 KKeyboard/Mouse Connector

CN Label:

KB_MS1 CN Type: CN Location: CN Pinouts:

Figure 3-20: External Peripheral Interface Connector

PS/2 See Figure 3-201 See Table 3-19

The keyboard and mouse connector is a standard PS/2 connector.

Figure 3-21: PS/2 Pinout and Configuration

Pin Description

1 KB DATA 2 MS DATA 3 GND 4 VCC 5 KB CLOCK

CPGN CPU Card

3.3.2 LLAN Connector

CN Label:

LAN1, LAN2 CN Type: CN Location: CN Pinouts:

3.3.3 UUSB Connector

CN Label:

USB_C1 CN Type: CN Location: CN Pinouts:

Pin Description

6 MS CLOCK

Table 3-19: Keyboard Connector Pinouts

RJ-45 See Figure 3-20 See Table 3-20

The LAN connector connects to a local network.

Pin Description Pin Description

1 TXA+ 5 TXC2 TXA- 6 TXB3 TXB+ 7 TXD+ 4 TXC+ 8 TXD-

Table 3-20: LAN Pinouts

USB port See Figure 3-20 See Table 3-21

The USB connector can be connected to a USB device.

Pin Description Pin Description

1 5 V 2 5 V 3 DATA- 4 DATA5 DATA+ 6 DATA+

3.3.4 VVGA Connector

CN Label:

VGA1 CN Type: CN Location: CN Pinouts:

Pin Description Pin Description

7 GND 8 GND

Table 3-21: USB Port Pinouts

15-pin Female See Figure 3-20 See Figure 3-22 and Table 3-22

The VGA connector connects to a monitor that accepts a standard VGA input.

Figure 3-22: VGA Connector

Pin Description Pin Description

1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VCC / NC 10 GND 11 NC 12 DDC DAT 13 HSYNC 14 VSYNC 15 DDCCLK

Table 3-22: VGA Connector Pinouts

CPGN CPU Card

Chapter

4 Installation

4.1 AAnti-static Precautions

WARNING:

4.2 IInstallation Considerations

NOTE:

Failure to take ESD precautions during the installation of the CPGN may result in permanent damage to the CPGN and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components, including the CPGN. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the CPGN or any other electrical component is handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

 Self-grounding: Before handling the board, touch any grounded conducting

material. During the time the board is handled, frequently touch any conducting materials that are connected to the ground.

 Use an anti-static pad: When configuring the CPGN, place it on an

antic-static pad. This reduces the possibility of ESD damaging the CPGN.

 Only handle the edges of the PCB: When handling the PCB, hold the PCB

by the edges.

The following installation notices and installation considerations should be read and understood before installation. All installation notices must be strictly adhered to. Failing to adhere to these precautions may lead to severe damage and injury to the person performing the installation.

CPGN CPU Card

WARNING:

4.3 BBasic Installation

The installation instructions described in this manual should be carefully followed in order to prevent damage to the components and injury to the user.

Before and during the installation please DO the following:

 Read the user manual:

• The user manual provides a complete description of the CPGN

installation instructions and configuration options.

 Wear an electrostatic discharge cuff (ESD):

• Electronic components are easily damaged by ESD. Wearing an ESD

cuff removes ESD from the body and helps prevent ESD damage.

 Place the CPGN on an antistatic pad:

• When installing or configuring the motherboard, place it on an antistatic

pad. This helps to prevent potential ESD damage.

 Turn all power to the CPGN off:

• When working with the CPGN, make sure that it is disconnected from all

power supplies and that no electricity is being fed into the system.

Before and during the installation of the CPGN DO NOT:

 Remove any of the stickers on the PCB board. These stickers are required for

warranty validation.

 Use the product before verifying all the cables and power connectors are

properly connected.

 Allow screws to come in contact with the PCB circuit, connector pins, or its

components.

This section outlines the parts that must be installed for the system to function correctly.

4.3.1 CCPU Installation

NOTE:

WARNING:

To enable Hyper-Threading, the CPU and chipset must both support it.

CPUs are expensive and sensitive components. When installing the CPU please be careful not to damage it in any way. Make sure the CPU is installed properly and ensure the correct cooling kit is properly installed.

The LGA775 socket is shown in Figure 4-1.

Figure 4-1: Intel LGA775 Socket

To install the CPU, follow the steps below.

DO NOT touch the pins at the bottom of the CPU. When handling the CPU, only hold it on the sides.

CPGN CPU Card

Step 1:

Step 2:

Step 3:

Step 4:

Remove the protective cover. The black protective cover can be removed by

pulling up on the tab labeled "Remove". See Figure 4-2.

Figure 4-2: Remove Protective Cover

Open the socket. Disengage the load lever by pressing the lever down and

slightly outward to clear the retention tab. Fully open the lever, then open the load plate. See Figure 4-3.

Figure 4-3: CPU Socket Load Plate

Inspect the CPU socket. Make sure there are no bent pins and make sure the

socket contacts are free of foreign material. If any debris is found, remove it with compressed air.

Orient the CPU properly. The contact array should be facing the CPU socket.

Step 5:

Step 6:

Step 7:

Step 8:

Step 9:

4.3.2 DDIMM Installation

Correctly position the CPU. Match the Pin 1 mark with the cut edge on the

CPU socket.

Align the CPU pins. Locate pin 1 and the two orientation notches on the CPU.

Carefully match the two orientation notches on the CPU with the socket alignment keys.

Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are

properly aligned, the CPU should slide into the CPU socket smoothly. See

Figure 4-4.

Figure 4-4: Insert the Socket LGA775 CPU

Close the CPU socket. Close the load plate and engage the load lever by

pushing it back to its original position. There will be some resistance, but will not require extreme pressure.

Connect the 12 V power to the board. Connect the 12 V power from the

power supply to the board. Step 0:

To install a DIMM, please follow the steps below and refer to Figure 4-5.

CPGN CPU Card

Step 1:

Step 2:

Step 3:

Step 4:

4.3.3 BBackplane Installation

Figure 4-5: DIMM Installation

Open the DIMM socket handles. Open the two handles outwards as far as they can. See Figure 4-5.

Align the DIMM with the socket. Align the DIMM so the notch on the memory

lines up with the notch on the memory socket. See Figure 4-5.

Insert the DIMM. Once aligned, press down until the DIMM is properly seated.

Clip the two handles into place. See Figure 4-5.

Removing a DIMM. To remove a DIMM, push both handles outward. The

memory module is ejected by a mechanism in the socket.Step 0:

Before the CPGN can be installed into the chassis, a backplane must first be installed. Please refer to the installation instructions that came with the backplane and the chassis to see how to install the backplane into the chassis.

NOTE:

4.3.4 CCPU Card Installation

4.4 JJumper Settings

NOTE:

Description

Label

Type

CyberResearch has a wide range of backplanes available. Please contact your CyberResearch® applications engineer or visit the CyberResearch website at www.cyberrsearch.com about the available backplanes.

to find out more

To install the CPGN CPU card onto the backplane, carefully align the CPU card interface connectors with the corresponding socket on the backplane. To do this, please refer to the reference material that came with the backplane. Next, secure the CPU card to the chassis. To do this, please refer to the reference material that came with the chassis.

A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper.

The CPGN includes one jumper shown in Table 4-1.

Clear CMOS jumper J_CMOS1 3-pin header

Table 4-1: Jumpers

CPGN CPU Card

4.4.1 CClear CMOS Jumper

Jumper Label:

J_CMOS1 Jumper Type: Jumper Settings: Jumper Location:

4.5 IInternal Peripheral Device Connections

4.5.1 SSATA Drive Connection

Step 1:

3-pin header See Table 4-2 See Figure 4-6

To reset the BIOS, move the jumper to the "Clear BIOS" position for 3 seconds or more, and then move back to the default position.

Pin Description

1-2 Normal 2-3 Clear BIOS

Table 4-2: Clear BIOS Jumper Settings

Figure 4-6: Clear BIOS Jumper Location

This section outlines the installation of peripheral devices to the onboard connectors.

The CPGN is shipped with two SATA drive cables and one SATA drive power cable. To connect the SATA drives to the connectors, please follow the steps below.

Locate the connectors. The locations of the SATA drive connectors are shown

in Chapter 3.

Step 2:

Insert the cable connector. Press the clip on the connector at the end of the

Step 3:

Step 1:

Figure 4-7: SATA Drive Cable Connection

SATA cable and insert the cable connector into the on-board SATA drive connector. See Figure 4-7.

Connect the cable to the SATA disk. Connect the connector on the other end

of the cable to the connector at the back of the SATA drive. See Figure 4-7

Connect the SATA power cable. Connect the SATA power connector to the

back of the SATA drive. See Figure 4-7. Step 0:

CPGN CPU Card

4.5.2 UUSB Cable (Dual Port) with Slot Bracket

Step 1:

WARNING:

Step 2:

Step 3:

Figure 4-8: SATA Power Drive Connection

The CPGN is shipped with a dual port USB 2.0 cable. To connect the USB cable connector, please follow the steps below.

Locate the connectors. The locations of the USB connectors are shown in

Chapter 3.

If the USB pins are not properly aligned, the USB device can burn out.

Align the connectors. The cable has two connectors. Correctly align pin 1on

each cable connector with pin 1 on the CPGN USB connector.

Insert the cable connectors. Once the cable connectors are properly aligned

with the USB connectors on the CPGN, connect the cable connectors to the on-board connectors. See Figure 4-9.

Step 4:

4.6 EExternal Peripheral Interface Connection

4.6.1 LLAN Connection

Figure 4-9: Dual USB Cable Connection

Attach the bracket to the chassis. The USB 2.0 connectors are attached to a

bracket. To secure the bracket to the chassis please refer to the installation instructions that came with the chassis.Step 0:

This section describes connecting devices to the external connectors on the CPGN.

There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection to an external network. To connect a LAN cable with an RJ-45 connector, please follow the instructions below.

CPGN CPU Card

Step 1:

Step 2:

Step 3:

4.6.2 UUSB Device Connection

Step 1:

Step 2:

Locate the RJ-45 connectors. The locations of the USB connectors are shown

in Chapter 4.

Align the connectors. Align the RJ-45 connector on the LAN cable with one of

the RJ-45 connectors on the CPGN. See Figure 4-10.

Figure 4-10: LAN Connection

Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN

cable RJ-45 connector into the on-board RJ-45 connector. Step 0:

There are two external USB 2.0 connectors. Both connectors are perpendicular to the CPGN. To connect a USB 2.0 or USB 1.1 device, please follow the instructions below.

Located the USB connectors. The locations of the USB connectors are shown

in Chapter 4.

Align the connectors. Align the USB device connector with one of the

connectors on the CPGN. See Figure 4-11

Figure 4-11: USB Device Connection

Step 3:

4.6.3 VVGA Monitor Connection

Step 1:

Step 2:

Step 3:

Insert the device connector. Once aligned, gently insert the USB device

connector into the on-board connector. Step 0:

The CPGN has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the CPGN, please follow the instructions below.

Locate the female DB-15 connector. The location of the female DB-15

connector is shown in Chapter 3.

Align the VGA connector. Align the male DB-15 connector on the VGA screen

cable with the female DB-15 connector on the external peripheral interface.

Insert the VGA connector. Once the connectors are properly aligned with the

insert the male connector from the VGA screen into the female connector on the CPGN. See Figure 4-12.

CPGN CPU Card

Step 4:

4.7 SSoftware Installation

Step 1:

NOTE:

Figure 4-12: VGA Connector

Secure the connector. Secure the DB-15 VGA connector from the VGA

monitor to the external interface by tightening the two retention screws on either side of the connector. Step 0:

All the drivers for the CPGN are on the CD or DVD that came with the system. To install the drivers, please follow the steps below.

Insert the disk into a drive connected to the system.

If the installation program doesn't start automatically: Click "Start->My Computer-> Drive->autorun.exe"

Step 2:

The disc main menu appears. Select Software/drivers.

Step 3:

Figure 4-13: Introduction Screen

A new screen with a list of available drivers appears (Figure 4-14).

Figure 4-14: Available Drivers

CPGN CPU Card

Step 4:

Install all of the necessary drivers in this menu. Step 0:

Figure 4-15: Choose drivers to install

Chapter

5 BIOS

CPGN CPU Card

5.1 IIntroduction

5.1.1 SStarting Setup

5.1.2 UUsing Setup

Key

Function

The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed.

The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways.

1. Press the D

2. Press the D appears on the screen. 0.

If the message disappears before the D again.

Use the arrow keys to highlight items, press ENTER to select, use the Page Up and Page Down keys to change entries, press F1 for help and press E are shown in.

Up arrow Mo ve to previous item Down arrow Move to next item Left arrow Move to the item on the left hand side

ELETE key as soon as the system is turned on or ELETE key when the “Press Del to enter SETUP” message

ELETE key is pressed, restart the computer and try

SC to quit. Navigation keys

Right arrow Move to the item on the right hand side Esc key Main Menu – Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu --

Exit current page and return to Main Menu Page Up key Increase the numeric value or make changes Page Dn key Decrease the numeric value or make changes F1 key General help, only for Status Page Setup Menu and

Option Page Setup Menu

Key

Function

5.1.3 GGetting Help

5.1.4 UUnable to Reboot after Configuration Changes

5.1.5 BBIOS Menu Bar

F2 /F3 key Change color from total 16 colors. F2 to select color

forward. F10 key Save all the CM OS changes, only for M ain Menu

Table 5-1: BIOS Navigation Keys

When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press E or the F1 key again.

If the computer cannot boot after changes to the system configuration is made, CMOS defaults. Use the jumper described in Chapter 5.

The menu bar on top of the BIOS screen has the following main items:

 Main – Changes the basic system configuration.  Advanced – Changes the advanced system settings.  PCIPnP – Changes the advanced PCI/PnP Settings  Boot – Changes the system boot configuration.  Security – Sets User and Supervisor Passwords.  Chipset – Changes the chipset settings.

 Power – Changes power management settings.  Exit – Selects exit options and loads default settings

The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above.

CPGN CPU Card

5.2 MMain

System Overview

The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

System Overview ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ AMIBIOS Version :08.00.15 Build Date :07/08/09 ID: :B153MT11

Processor Type :Intel® Core™2 CPU E8400 @ 3.00GHz Speed :3000MHz Count :1

System Memory Size :2014MB

System Time [14:20:27] System Time [Tue 010/08/2009]

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 1: Main



The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed. The items shown in the system overview include:

 AMI BIOS: Displays auto-detected BIOS information

• Version: Current BIOS version

• Build Date: Date the current BIOS version was made

• ID: Installed BIOS ID

 Processor: Displays auto-detected CPU specifications

• Type: Names the currently installed processor

• Speed: Lists the processor speed

• Count: The number of CPUs on the motherboard

 System Memory: Displays the auto-detected system memory.

• Size: Lists memory size

The System Overview field also has two user configurable fields:

System Time [xx:xx:xx]

System Date [xx/xx/xx]

5.3 AAdvanced

WARNING!



Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.



Use the System Date option to set the system date. Manually enter the day, month and year.

Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus:

Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.

 CPU Configuration (see Section 5.3.1)  IDE Configuration (see Section 5.3.2)  Floppy Configuration (see Section 5.3.3)  Super IO Configuration (see Section 5.3.3)  Hardware Health Configuration (see Section 5.3.5)  Power Configuration (see Section  Remote Access Configuration (see Section 5.3.7)  USB Configuration (see Section 5.3.8)

)

CPGN CPU Card

5.3.1 CCPU Configuration

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Advanced Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below sections may cause system to malfunction

> CPU Configuration > IDE Configuration > SuperIO Configuration > Hardware Health Configuration > Power Configuration > Remote Access Configuration > USB Configuration

BIOS Menu 2: Advanced

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications and configure the CPU.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Configure Advanced CPU Settings Module Version:3F.15 ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Manufacturer :Intel® Intel® Core™2 Quad CPU Q9300 @ 2.50GHz Frequency :2.50GHz FSB Speed :1333MHz

Cache L1 :128KB Cache L2 :6144KB

Ratio Actual Value:7.5

BIOS Menu 3: CPU Configuration

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

The CPU Configuration menu (BIOS Menu 3) lists the following CPU details:

 Manufacturer: Lists the name of the CPU manufacturer  Brand String: Lists the brand name of the CPU being used

 Frequency: Lists the CPU processing speed

5.3.2 IIDE Configuration

ATA/IDE Configurations [Compatible]

 FSB Speed: Lists the FSB speed  Cache L1: Lists the CPU L1 cache size  Cache L2: Lists the CPU L2 cache size

Use the IDE Configuration menu (BIOS Menu 4) to change and/or set the configuration of the IDE devices installed in the system.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

IDE Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ ATA/IDE Configuration [Enhanced] Configure SATA as [IDE] Configure SATA Channels [Before PATA]

> Primary IDE Master : [Not Detected] > Primary IDE Slave : [Not Detected] > Secondary IDE Master : [Not Detected] > Secondary IDE Slave : [Not Detected] > Third IDE Master : [Not Detected] > Third IDE Slave : [Not Detected]

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 4: IDE Configuration



Use the ATA/IDE Configurations option to configure the ATA/IDE controller.



Disabled Disables the on-board ATA/IDE controller.



Compatible Configures the on-board ATA/IDE controller to be in

compatible mode. In this mode, a SATA channel will replace one of the IDE channels. This mode supports up to 4 storage devices.

CPGN CPU Card

Configure SATA as [IDE]

Configure SATA Channels [Behind PATA]

IDE Master and IDE Slave



Enhanced DEFAULT Configures the on-board ATA/IDE controller to be in

Enhanced mode. In this mode, IDE channels and SATA channels are separated. This mode supports up to 6 storage devices. Some legacy OS do not support this mode.



Use the Configure SATA as option to configure SATA devices as normal IDE devices.



IDE DEFAULT Configures SATA devices as normal IDE device.



Use the Configure SATA Channels option to determine how SATA channels and PATA channels are ordered.



Before PATA Puts SATA channels before PATA channels.



Behind PATA DEFAULT Puts SATA channels behind PATA channels.



When entering setup, BIOS automatically detects the presence of IDE devices. BIOS displays the status of the automatically detected IDE devices. The following IDE devices are detected and are shown in the IDE Configuration menu:

 Primary IDE Master  Primary IDE Slave  Secondary IDE Master  Secondary IDE Slave  Third IDE Master  Third IDE Slave

The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the IDE devices installed in the system. If an IDE device is detected and one of the above listed four BIOS configuration options are selected, the IDE configuration options shown in Section 5.3.2.1 appear.

5.3.2.1 IIDE Master, IDE Slave

Auto-Detected Drive Parameters

Use the IDE Master and IDE Slave configuration menu to view both primary and secondary IDE device details and configure the IDE devices connected to the system.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Primary IDE Master ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Device :Not Detected

Type [Auto] LBA/Large Mode [Auto] Block (Multi-Sector Transfer) [Auto] PIO Mode [Auto] DMA Mode [Auto] S.M.A.R.T. [Auto] 32Bit Data Transfer [Enabled]

BIOS Menu 5: IDE Ma s te r and IDE Slave Configuration

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit



The “grayed-out” items in the left frame are IDE disk drive parameters automatically detected from the firmware of the selected IDE disk drive. The drive parameters are listed as follows:

 Device: Lists the device type (e.g. hard disk, CD-ROM etc.)  Type: Indicates the type of devices a user can manually select  Vendor: Lists the device manufacturer  Size: List the storage capacity of the device.  LBA Mode: Indicates whether the LBA (Logical Block Addressing) is a

method of addressing data on a disk drive is supported or not.

 Block Mode: Block mode boosts IDE drive performance by increasing the

amount of data transferred. Only 512 bytes of data can be transferred per interrupt if block mode is not used. Block mode allows transfers of up to 64 KB per interrupt.

 PIO Mode: Indicates the PIO mode of the installed device.

CPGN CPU Card

Type [Auto]

LBA/Large Mode [Auto]

 Async DMA: Indicates the highest Asynchronous DMA Mode that is

supported.

 Ultra DMA: Indicates the highest Synchronous DMA Mode that is supported.  S.M.A.R.T.: Indicates whether or not the Self-Monitoring Analysis and

Reporting Technology protocol is supported.

 32Bit Data Transfer: Enables 32-bit data transfer.



Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from after the Power-On Self-Test (POST) is comp lete.



Not Installed BIOS is prevented from searching for an IDE disk

drive on the specified channel.



Auto DEFAULT The BIOS automatically detects the IDE disk drive

type attached to the specified channel. This setting should be used if an IDE hard disk drive is attached to the specified channel.



CD/DVD The CD/DVD option specifies that an IDE CD-ROM

drive is attached to the specified IDE channel. The BIOS does not attempt to search for other types of IDE disk drives on the specified channel.



ARMD This option specifies an ATAPI Removable Media

Device. These include, but are not limited to: ZIP LS-120



Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the maximum drive capacity is 137 GB.



Disabled BIOS is prevented from using the LBA mode control on

the specified channel.



Block (Multi Sector Transfer) [Auto]

PIO Mode [Auto]

Auto DEFAULT BIOS auto detects the LBA mode control on the specified

channel.



Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect if the device supports multi-sector transfers.



Disabled BIOS is prevented from using Multi-Sector Transfer on

the specified channel. The data to and from the device occurs one sector at a time.



Auto DEFAULT BIOS auto detects Multi-Sector Transfer support on the

drive on the specified channel. If supported the data transfer to and from the device occurs multiple sectors at a time.



Use the PIO Mode option to select the IDE PIO (Programmable I / O) mode program ti ming cycles between the IDE drive and the programmable IDE controller. As the PIO mode increases, the cycle time decreases.



Auto DEFAULT BIOS auto detects the PIO mode. Use this value if the IDE disk

drive support cannot be determined.



0 PIO mode 0 selected with a maximum transfer rate of 3.3 MB/s



1 PIO mode 1 selected with a maximum transfer rate of 5.2 MB/s



2 PIO mode 2 selected with a maximum transfer rate of 8.3 MB/s



3 PIO mode 3 selected with a maximum transfer rate of 11.1 MB/s



4 PIO mode 4 selected with a maximum transfer rate of 16.6 MB/s

(This setting generally works with all hard disk drives manufactured after 1999. For other disk drives, such as IDE CD-ROM drives, check the specifications of the drive.)

CPGN CPU Card

DMA Mode [Auto]



Use the DMA Mode BIOS selection to adjust the DMA mode options.



Auto DEFAULT BIOS auto detects the DM A mode. Use this value if the IDE

disk drive support cannot be determined.



SWDMA0 Single Word DMA mode 0 selected with a maximum data

transfer rate of 2.1 MB/s



SWDMA1 Single Word DMA mode 1 selected with a maximum data

transfer rate of 4.2 MB/s



SWDMA2 Single Word DMA mode 2 selected with a maximum data

transfer rate of 8.3 MB/s



MWDMA0 Multi Word DMA mode 0 selected with a maximum data

transfer rate of 4.2 MB/s



MWDMA1 Multi Word DMA mode 1 selected with a maximum data

transfer rate of 13.3 MB/s



MWDMA2 Multi Word DMA mode 2 selected with a maximum data

transfer rate of 16.6 MB/s



UDMA0 Ultra DMA mode 0 selected with a maximum data transfer

rate of 16.6 MB/s



UDMA1 Ultra DMA mode 1 selected with a maximum data transfer

rate of 25 MB/s



UDMA2 Ultra DMA mode 2 selected with a maximum data transfer

rate of 33.3 MB/s



UDMA3 Ultra DMA mode 3 selected with a maximum data transfer

rate of 44 MB/s (To use this mode, it is required that an 80-conductor ATA cable is used.)



UDMA4 Ultra DMA mode 4 selected with a maximum data transfer

rate of 66.6 MB/s (To use this mode, it is required that an 80-conductor ATA cable is used.)



S.M.A.R.T [Auto]

32Bit Data Transfer [Enabled]

5.3.3 FFloppy Configuration

UDMA5 Ultra DMA mode 5 selected with a maximum data transfer

rate of 99.9 MB/s (To use this mode, it is required that an 80-conductor ATA cable is used.)



Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and Reporting Technology (SMART) on the drive on the specified channel. S.M.A.R.T predicts impending drive failures. The S.M.A.R.T BIOS option enables or disables this function.



Auto DEFAULT BIOS auto detects HDD SMART support.



Disabled Prevents BIOS from using the HDD SMART feature.



Enabled Allows BIOS to use the HDD SMART feature



Use the 32Bit Data Transfer BIOS option to enables or disable 32-bit data transfers.



Disabled Prevents the BIOS from using 32-bit data transfers.



Enabled DEFAULT Allows BIOS to use 32-bit data transfers on supported

Use the Floppy Configuration menu to configure the floppy disk drive connected to the system.

hard disk drives.

CPGN CPU Card

Floppy A/B

5.3.4 SSuper IO Configuration

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Power Exit

Floppy Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Floppy A [Disabled]

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 6: IDE Master and IDE Slave Configuration



Use the Floppy A/B option to configure the floppy disk drive. Options are listed below:

 Disabled  1.44 MB 3 1/2’

Use the Super IO Configuration menu (BIOS Menu 7) to set or change the configurations for the FDD controllers, parallel ports and serial ports.

BIOS SETUP UTILITY

Parallel Port Address [Disabled]

Parallel Port Mode [Normal]

Main Advanced PCIPNP Boot Security Chipset Exit

Super I/O Chipset ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Parallel Port Address [378]

Parallel Port Mode [Normal] Parallel Port IRQ [IRQ7]

Serial Port1 Address [3F8/IRQ4]

Serial Port1 Mode [Normal]

Serial Port2 Address [2F8/IRQ3]

Serial Port2 Mode [Normal]

BIOS Menu 7: Super IO Configuration



Use the Parallel Port Address option to select the parallel port base address.

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit



Disabled DEFAULT No base address is assigned to the Parallel Port



378 Parallel Port I/O port address is 378



278 Parallel Port I/O port address is 278



3BC Parallel Port I/O port address is 3BC



Use the Parallel Port Mode option to select the mode the parallel port operates in.



Normal DEFAULT The normal parallel port mode is the standard mode

for parallel port operation.



Bi-directional Parallel port outputs are 8-bits long. Inputs are

accomplished by reading 4 of the 8 bits on the status register.

CPGN CPU Card

Parallel Port IRQ [IRQ7]

Serial Port1 Address [3F8/IRQ4]



EPP The parallel port operates in the enhanced parallel

port mode (EPP). The EPP mode supports bi-directional communication between the system and the parallel port device and the transmission rates between the two are much faster than the Normal mode.



ECP+EPP The parallel port operates in the extended

capabilities port (ECP) mode. The ECP mode supports bi-directional communication between the system and the parallel port device and the transmission rates between the two are much faster than the Normal mode

The parallel port is also be compatible with EPP devices described above



Use the Parallel Port IRQ selection to set the parallel port interrupt address.



IRQ5 IRQ5 is assigned as the parallel port interrupt address



IRQ7 DEFAULT IRQ7 is assigned as the parallel port interrupt address



Use the Serial Port1 Address option to select the Serial Port 1 base address.



Disabled No base address is assigned to Serial Port 1



3F8/IRQ4 DEFAULT Serial Port 1 I/O port address is 3F8 and the interrupt

address is IRQ4



3E8/IRQ4 Serial Port 1 I/O port address is 3E8 and the interrupt

address is IRQ4



2E8/IRQ3 Serial Port 1 I/O port address is 2E8 and the interrupt

address is IRQ3



Serial Port1 Mode [Normal]

Serial Port2 Address [2F8/IRQ3]

Serial Port2 Mode [Normal]

Use the Serial Port1 Mode option to select the transmitting and receiving mode for the first serial port.



Normal DEFAULT Serial Port 1 mode is normal



IrDA Serial Port 1 mode is IrDA



ASK IR Serial Port 1 mode is ASK IR



Use the Serial Port2 Address option to select the Serial Port 2 base address.



Disabled No base address is assigned to Serial Port 2



2F8/IRQ3 DEFAULT Serial Port 2 I/O port address is 3F8 and the interrupt

address is IRQ3



3E8/IRQ4 Serial Port 2 I/O port address is 3E8 and the interrupt

address is IRQ4



2E8/IRQ3 Serial Port 2 I/O port address is 2E8 and the interrupt

address is IRQ3



Use the Serial Port2 Mode option to select the Serial Port2 operational mode.



Normal DEFAULT Serial Port 2 mode is normal



IrDA Serial Port 2 mode is IrDA



ASK IR Serial Port 2 mode is ASK IR

CPGN CPU Card

5.3.5 HHardware Health Configuration

Mode Setting [Full On Mode]

The Hardware Health Configuration menu (BIOS Menu 8) shows the operating temperature, fan speeds and system voltages.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Hardware Health Event Monitoring ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ CPU_FAN Mode Setting [Full On Mode]

CPU Temperature :30ºC/86ºF System Temperature :33ºC/91ºF

CPU Fan Speed :1735 RPM

CPU Core :1.216 V

1.125V :1.136 V

3.3V :3.296 V

5.0V :4.945 V

12.V :11.840 V

1.5V :1.520V

1.8V :1.920 V 5V Dual :4.945 V VBAT :3.056 V

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 8: Hardware Health Configuration



Use the Mode Setting option to configure the fan.



Full On Mode DEFAULT Fan is on all the time



Automatic mode The fan adjusts its speed using these settings:

Temp. Limit of OFF Temp. Limit of Start Fan Start PWM Slope PWM 1



PWM Manual mode The fan spins at the speed set in:

Fan PWM control

Temp. Limit of OFF [000]

WARNING:

Temp. Limit of Start [020]

WARNING:

Start PWM [070]

Slope PWM [1 PWM]



CPU failure can result if this value is set too high

The fan will turn off if the temperature falls below this value.

 Minimum Value: 0°C  Maximum Value: 127°C



CPU failure can result if this value is set too high

When the fan is off, it will only start when the temperature exceeds this setting.

 Minimum Value: 0°C  Maximum Value: 127°C



This is the initial speed of the fan when it first starts spinning.

 PWM Minimum Mode: 0  PWM Maximum Mode: 127



A bigger value will increase the fan speed in big amounts. A smaller value will increase the speed more gradually.

 0 PWM  1 PWM  2 PWM

CPGN CPU Card

CPU Fan PWM Control [070]

Hardware Health Monitoring

 4 PWM  8 PWM  16 PWM  32 PWM  64 PWM



This value specifies the speed of the fan.

 PWM Minimum Mode: 0  PWM Maximum Mode: 127



The following system parameters and values are shown. The system parameters that are monitored are:

 System Temperatures:

• CPU Temperature

• System Temperature

 Fan Speeds:

• CPU Fan Speed

• SYS Fan Speed

 Voltages:

• CPU Core

• +1.125 V

• +3.3 V

• +5 V

• +12 V

• +1.5 V

• +1.8 V

• 5V Dual

• VBAT

5.3.6 PPower Configuration

5.3.6.1 AACPI Settings

Use the Power Configuration menu (BIOS Menu 10) configures the Advanced Configuration and Power Interface (ACPI) and Power Management (APM) options.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Select AT/ATX Power [ATX Power] ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ > ACPI Configuration > APM Configuration

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 9: ACPI Configuration

Use the General ACPI Settings menu (BIOS Menu 10) to select the ACPI state when the system is suspended.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Power Exit

ACPI Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Suspend mode [S1 (POS)]

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 10: ACPI Settings

CPGN CPU Card

Suspend Mode [S1(POS)]

5.3.6.2 AAPM Configuration

Restore on AC Power Loss [Last State]



Use the Suspend Mode option to specify the sleep state the system enters when it is not being used.



S1 (POS) DEFAULT The system enters S1 (POS) sleep state. The system

appears off. The CPU is stopped; RAM is refreshed; the system is running in a low power mode.

The APM Configuration menu (BIOS Menu 11) allows the advanced power management options to be configured.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Power Exit

APM Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Restore on AC Power Loss [Last State] Power Button Mode [On/Off]

Advanced Resume Event Controls Resume on Keyboard/Mouse [Disabled] Resume On Ring [Disabled] Resume on PCI Express Wake [Disabled] Resume on RTC Alarm [Disabled]

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 11: APM Configuration



Use the Restore on AC Power Loss BIOS option to specify what state the system returns to if there is a sudden loss of power to the system.



Power Off The system remains turned off



Power On The system turns on



Last State DEFAULT The system returns to its previous state. If it was on, it

turns itself on. If it was off, it remains off.



Resume on Keyboard/Mouse [Disabled]

Resume on Ring [Disabled]

Resume on PCI-Express WAKE# [Enabled]

Resume On RTC Alarm [Disabled]

Use the Resume on Keyboard/Mouse BIOS option to enable activity on either the keyboard or mouse to rouse the system from a suspend or standby state. That is, the system is roused when the mouse is moved or a button on the keyboard is pressed.



Disabled DEFAULT Wake event not generated by activity on the

keyboard or mouse



Resume On KeyBoard



Resume On Mouse



Enabled Wake event generated by activity on the keyboard



Use the Resume on Ring BIOS option to enable activity on the RI (ring in) modem line to

Wake event generated by activity on the keyboard

Wake event generated by activity on the mouse

or mouse

rouse the system from a suspend or standby state. That is, the system will be roused by an incoming call on a modem.



Disabled DEFAULT Wake event not generated by an incom ing call



Enabled Wake event generated by an incoming call



The Resume on PCI-Express WAKE# BIOS option specifies if the system is roused from a suspended or standby state when there is activity on the PCI-Express bus.



Disabled Wake event not generated by PCI-Express activity



Enabled DEFAULT Wake event generated by PCI-Express activity



Use the Resume On RTC Alarm option to specify the time the system should be roused from a suspended state.

CPGN CPU Card

5.3.7 RRemote Access Configuration

Remote Access [Disabled]



Disabled DEFAULT The real time clock (RTC) cannot generate a wake

event



Enabled If selected, the following appears with values that

can be selected: RTC Alarm Date (Days) System Time After setting the alarm, the computer turns itself on

from a suspend state when the alarm goes off.

Use the Remote Access Configuration menu (BIOS Menu 12) to configure remote access parameters. The Remote Access Configuration is an AMIBIOS feature and allows a remote host running a terminal program to display and configure the BIOS settings.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Configure Remote Access type and parameters ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Remote Access [Disabled]

Serial port number [COM1] Base Address, IRQ [3F8H, 4] Serial Port Mode [115200 8,n,1] Redirection After BIOS POST [Always] Terminal Type [ANSI]

BIOS Menu 12: Remote Access Configuration



Use the Remote Access option to enable or disable access to the remote functionalities

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

of the system.



Disabled DEFAULT Remote access is disabled.



Serial Port Number [COM1]

Base Address, IRQ [2F8h,3]

Serial Port Mode [115200 8,n,1]

Enabled Remote access configuration options shown

below appear: Serial Port Number Serial Port Mode Flow Control Redirection after BIOS POST Terminal Type These configuration options are discussed below.



Use the Serial Port Number option to select the serial port used for remote access.



COM1 DEFAULT System is remotely accessed through COM1



COM2 System is rem otely accessed through COM 2

NOTE: Make sure the selected COM port is enabled through the Super I/O configuration

menu.



The Base Address, IRQ option cannot be configured and only shows the interrupt address of the serial port listed above.



Use the Serial Port Mode option to select baud rate through which the console redirection is made. The following configuration options are available

 115200 8,n,1 D  57600 8,n,1  38400 8,n,1  19200 8,n,1  09600 8,n,1

EFAULT

CPGN CPU Card

NOTE:

Redirection After BIOS POST [Always]

Terminal Type [ANSI]

5.3.8 UUSB Configuration

Identical baud rate setting musts be set on the host (a management computer running a terminal software) and the slave



Use the Redirection After BIOS POST option to specify when console redirection should occur.



Disabled The console is not redirected after POST



Boot Loader Redirection is active during POST and during Boot

Loader



Always DEFAULT Redirection is always active (Some OSes may not



Use the Terminal Type BIOS option to specify the remote terminal type.



ANSI DEFAULT The target terminal type is ANSI



VT100 The target terminal type is VT100



VT-UTF8 The target terminal type is VT-UTF8

Use the USB Configuration menu (BIOS Menu 13) to read USB configuration information and configure the USB settings.

work if set to Always)

BIOS SETUP UTILITY

USB Configuration

USB Devices Enabled

USB Function [Enabled]

USB 2.0 Controller [Enabled]

Main Advanced PCIPNP Boot Security Chipset Exit

USB Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Module Version – 2.24.3-13.4

USB Devices Enabled: None

USB Function [Enabled] USB 2.0 Controller [Enabled] Legacy USB Support [Enabled] USB 2.0 Controller Mode [HiSpeed]

BIOS Menu 13: USB Configuration



The USB Configuration field shows the system USB configuration. The items listed are:

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

 Module Version: x.xxxxx.xxxxx



The USB Devices Enabled field lists the USB devices that are enabled on the system



Use the USB Function BIOS option to enable or disable USB function support.



Disabled USB function support disabled



Enabled DEFAULT USB function support enabled



Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller



Disabled USB 2.0 controller disabled



Enabled DEFAULT USB 2.0 controller enabled

CPGN CPU Card

Legacy USB Support [Enabled]

USB2.0 Controller Mode [HiSpeed]

5.4 PPCI/PnP

WARNING!



Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there is no USB driver loaded onto the system.



Disabled Legacy USB support disabled



Enabled DEFAULT Legacy USB support enabled



Auto Legacy USB support disabled if no USB devices are

connected



Use the USB2.0 Controller Mode option to set the speed of the USB2.0 controller.



FullSpeed The controller is capable of operating at 12 Mb/s



HiSpeed DEFAULT The controller is capable of operating at 480 M b /s

Use the PCI/PnP menu (BIOS Menu 14) to configure advanced PCI and PnP settings.

Setting wrong values for the BIOS selections in the PCIPnP BIOS menu may cause the system to malfunction.

BIOS SETUP UTILITY

IRQ# [Available]

Main Advanced PCIPNP Boot Security Chipset Exit

Advanced PCI/PnP Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below sections may cause system to malfunction IRQ3 [Reserved] IRQ4 [Reserved] IRQ5 [Available] IRQ7 [Available] IRQ9 [Available] IRQ10 [Available] IRQ11 [Available] IRQ14 [Available] IRQ15 [Available]

DMA Channel 0 [Available] DMA Channel 1 [Available] DMA Channel 3 [Available] DMA Channel 5 [Available] DMA Channel 6 [Available] DMA Channel 7 [Available]

Reserved Memory Size [Disabled]

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 14: PCI/PnP Configuration



Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral device.



Available DEFAULT The specified IRQ is available to be used by

PCI/PnP devices



Reserved The specified IRQ is reserved for use by Legacy ISA

devices

Available IRQ addresses are:

 IRQ3  IRQ4  IRQ5  IRQ7  IRQ9

CPGN CPU Card

DMA Channel# [Available]

Reserved Memory Size [Disabled]

 IRQ10  IRQ 11  IRQ 14  IRQ 15



Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device.



Available DEFAULT The specified DMA is available to be used by

PCI/PnP devices



Reserved The specified DMA is reserved for use by Legacy

ISA devices

Available DMA Channels are:

 DM Channel 0  DM Channel 1  DM Channel 3  DM Channel 5  DM Channel 6  DM Channel 7



Use the Reserved Memory Size BIOS option to specify the amount of memory that should be reserved for legacy ISA devices.



Disabled DEFAULT No memo ry block reserved for legacy ISA devices



16K 16 KB reserved for legacy ISA devices



32K 32 KB reserved for legacy ISA devices



64K 54 KB reserved for legacy ISA devices

5.5 BBoot

5.5.1 BBoot Settings Configuration

Use the Boot menu (BIOS Menu 15) to configure system boot options.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Boot Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ > Boot Settings Configuration

> Boot Device Priority > Hard Disk Drives > CD/DVD Drives > Removable Drives

BIOS Menu 15: Boot

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

Use the Boot Settings Configuration menu (BIOS Menu 16) to configure advanced system boot options.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Boot Settings Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Quick Boot [Enabled] Quiet Boot [Enabled] AddOn ROM Display Mode [Force BIOS] Bootup Num-Lock [On] Boot From LAN Support [Disabled]

BIOS Menu 16: Boot Settings Configuration

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

CPGN CPU Card

Quick Boot [Enabled]

Quiet Boot [Disabled]

AddOn ROM Display Mode [Force BIOS]

Bootup Num-Lock [On]



Use the Quick Boot BIOS option to make the computer speed up the boot process.



Disabled No POST procedures are skipped



Enabled DEFAULT Some POST procedures are skipped to decrease

the system boot time



Use the Quiet Boot BIOS option to select the screen display when the system boots.



Disabled DEFAULT Normal POST messages displayed



Enabled OEM Logo displayed instead of POST messages



Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed.



Force BIOS DEFAULT The system forces third party BIOS to display

during system boot.



Keep Current The system displays normal information during

system boot.



Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be modified during boot up.



Off Does not enable the keyboard Number Lock automatically. To

use the 10-keys on the keyboard, press the Number Lock key located on the upper left-hand corner of the 10-key pad. The Number Lock LED on the keyboard lights up when the Number Lock is engaged.



Boot From LAN Support [Disabled]

5.5.2 BBoot Device Priority

On DEFAULT Allows the Number Lock on the keyboard to be enabled

automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit.



Use the BOOT From LAN Support option to enable the system to be booted from a remote system.



Disabled DEFAULT Cannot be booted from a remote system through the

LAN



Enabled DEFAULT Can be booted from a remote system through the

LAN

Use the Boot Device Priority menu (BIOS Menu 17) to specify the boot sequence from the available devices. The drive sequence also depends on the boot sequence in the individual device section.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Boot Device Priority ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ > 1st Boot Device [1st Boot Device] > 2nd Boot Device [2nd Boot Device] > 3rd Boot Device [3rd Boot Device]

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 17: Boot Device Priority Settings

CPGN CPU Card

5.5.3 HHard Disk Drives

5.5.4 RRemovable Drives

Use the Hard Disk Drives menu to specify the boot sequence of the available HDDs. Only installed hard drives are shown.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Hard Disk Drives ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ > 1st Drive [Hard Drive 1] > 2nd Drive [Hard Drive 2] > 3rd Drive [Hard Drive 3]

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 18: Hard Disk Drives

Use the Removable Drives menu (BIOS Menu 19) to specify the boot sequence of the removable drives. Only connected drives are shown.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Hard Disk Drives ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ > 1st Drive [Removable Drive 1] > 2nd Drive [Removable Drive 2] > 3rd Drive [Removable Drive 3]

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 19: Removable Drives

CD/DVD Drives

5.6 SSecurity

Use the CD/DVD Drives menu to specify the boot sequence of the available CD/DVD drives.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Hard Disk Drives ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ > 1st Drive [CD/DVD 1] > 2nd Drive [CD/DVD 2] > 3rd Drive [CD/DVD 3]

 Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

BIOS Menu 20: CD/DVD Drives

Use the Security menu (BIOS Menu 21) to set system and user passwords.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Security Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Supervisor Password :Not Installed User Password :Not Installed

Change Supervisor Password Change User Password

BIOS Menu 21: Security

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

CPGN CPU Card

Change Supervisor Password

Change User Password

Clear User Password

Boot Sector Virus Protection [Disabled]

5.7 CChipset

WARNING!



Use the Change Supervisor Password to set or change a supervisor password. The default for this option is Not Installed. If a supervisor password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change Supervisor Password.



Use the Change User Password to set or change a user password. The default for this option is Not Installed. If a user password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change User Password.



Use the Clear User Password to clear a user’s password. The default for this option is Not Installed. If a user password must be cleared, use this option.



Use the Boot Sector Virus Protection to enable or disable boot sector protection.



Disabled DEFAULT Disables the boot sector virus protection



Enabled Enables the boot sector virus protection

Use the Chipset menu (BIOS Menu 22) to access the Northbridge and Southbridge configuration menus

Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.

BIOS SETUP UTILITY

5.7.1 NNorthbridge Configuration

Memory Remap Feature [Enabled]

Main Advanced PCIPNP Boot Security Chipset Exit

Advanced Chipset Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below section may cause system to malfunction.

> Northbridge Configuration > Southbridge Configuration

BIOS Menu 22: Chipset

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

Use the Northbridge Chipset Configuration menu (BIOS Menu 23) to configure the Northbridge chipset.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Northbridge Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Memory Remap Feature [Enabled] PCI MMIO Allocation: 4GB to 3072MB Memory Hole [Disabled]

Initate Graphic Adapter [PCI/IGD] IDG Graphics Mode Select [Enabled, 32MB]

> Video Function Configuration

BIOS Menu 23:Northbridge Chipset Configuration



Use the Memory Remap Feature option to allow the overlapped PCI memory above the

 Select Screen

↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit

total physical memory to be remapped.

CPGN CPU Card

Memory Hole [Disabled]

Initiate Graphic Adapter

IGD Graphics Mode Select [Enable, 32 MB]



Enabled DEFAULT Overlapped PCI memory can be remapped



Disabled Overlapped PCI memory cannot be remapped



Use the Memory Hole option to reserve memory space between 15 MB and 16 MB for ISA expansion cards that require a specified area of memory to work properly. If an older ISA expansion card is used, please refer to the documentation that came with the card to see if it is necessary to reserve the space.



Disabled DEFAULT Memory is not reserved for ISA expansion cards



15 MB–16 MB Between 15 MB and 16 MB of memory is reserved

for ISA expansion cards



Use the Initiate Graphic Adapter option to select the graphics controller used as the primary boot device. Select either an integrated graphics controller (IGD) or a combination of PCI graphics controller, a PCI express (PEG) controller or an IGD. Configuration options are listed below:

 IGD  PCI/IGD D



Use the IGD Graphic Mode Select option to specify the amount of system memory that can be used by the internal graphics device.



Disable

EFAULT



Enable, 32 MB DEFAULT 32 MB of memory used by internal graphics device



Enable, 64 MB 64 MB of memory used by internal graphics device



Enable, 128 MB 128 MB of memory used by internal graphics device

CyberResearch CPGN CQ-30-X, CPGN CQ-26-X, CPGN C2-30-X, CPGN PE-29-X User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual