CyberLink Area-51 m5700 User Manual

i -1

Notice

The information in this user’s manual is subject to change without notice.

THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS OR

OMISSIONS CONTAINED IN THIS MANUAL AND SHALL NOT BE LIABLE FOR ANY

CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM THE PERFORMANCE

OR USE OF THIS MANUAL.



The information in this user’s manual is protected by copyright laws. No part of this

manual may be photocopied or reproduced in any form without prior written

authorization from the copyright owners.

Copyright March, 2005

All rights reserved.

Microsoft and Windows are registered trademarks of Microsoft Corporation. DOS,
Windows 95/98/ME/2000/NT/XP are trademarks of Microsoft Corporation.

Product names mentioned herein may be trademarks and/or registered trademarks of
their respective owners/companies.

The software described in this manual is delivered under a license agreement. The
software may be used or copied only in accordance with the terms of the agreement.

This product incorporates copyright protection technology that is protected by U.S.
patents and other intellectual property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.

Rev 1.0

i -2

TABLE OF CONTENTS

PREFACE

Symbols and Conventions

Protecting Your Computer - Avoid Abusive Handling and Adverse

Environments

Chapter Summaries

1. GETTING TO KNOW THE BASICS

Performance Features (1-2,3)

System at a Glance (1-4)

Top View (1-4,5,6)

Front and Rear Views (1-7,8)

Side Views (1-9,10)

Bottom View (1-11,12)

AC Adapter (1-13)

LED Status Indicators (1-14)

Keyboard Features (1-15)

Function (Quick) Keys (1-15)

Windows Keys (1-16)

Embedded Numeric Keypad (1-16)

Touch Pad (1-17)

Graphic Subsystem (1-18)

Adjusting the Display Brightness (1-18)

Extending the Life of the TFT Display Panel (1-18)

Opening and Closing the Display Panel (1-19)

Audio Subsystem (1-20)

Adjusting the Volume in Windows (1-20)

Voice Recording (1-20)

Modem and Modem Settings (1-21)

Ethernet Adapter (1-22)

2. BIOS SETUP AND SECURITY

Entering the BIOS Setup Screen (2-3)

Leaving the BIOS Setup Screen (2-3)

BIOS Action Keys (2-3)

i -3

Modifying the BIOS Settings (2-4)

Main Setup (2-4)

Advance Setup (2-4,5)

Security Setup (2-5,6)

Power Setup (2-7)

Boot Setup (2-8)

Exit Setup (2-9)

3. BATTERY POWER & POWER MANAGEMENT

The Battery Pack (3-2)

Lithium-Ion Battery Technology (3-2)

Battery Low-Power Warning (3-3)

Installing and Removing the Battery Pack (3-4,5)

Charging the Battery and Charging Time (3-5)

Checking the Battery Level (3-6)

Prolonging the Battery’s Life and Usage Cycles (3-6)

Using Windows Power Options (3-7)

Windows’ Power Schemes (3-7,8)

Suspend Modes (3-9,10)

Power Button Action (3-11)

Low Battery Warning (3-12)

Power Manual Quick Access (3-13)

4. UPGRADING YOUR COMPUTER

Upgrading the Hard Disk Drive (4-2,3,4,5)

Upgrading the System Memory (4-6,7,8,9)

Installing a Mini PCI Card to the System (4-10,11,12)

5. TROUBLESHOOTING

First Step (5-2,3)

Audio Problems (5-4)

Hard Disk Problems (5-5,6)

Optical Drive Problems (5-7)

Display Problems (5-8)

Keyboard and Mouse Problems (5-9)

CMOS Battery Problems (5-10)

Memory Problems (5-11)

i -4

Modem Problems (5-12)

Network Adapter / Ethernet Problems (5-13)

Express Card Problems (5-14)

Performance Problems (5-15)

Firewire (IEEE1394) and USB2.0 Problems (5-16)

APPENDIX A Product Specification

APPENDIX B Agency Regulatory Notices

APPENDIX C CyberLink Power Cinema Guide

Preface

Using This Manual

This User’s Manual contains general information about the hardware
and software setup, troubleshooting, and technical specifications of
the notebook computer.

Symbols and Conventions

The following conventions and symbols are used in this manual:

 When keys are to be pressed at the same time, a plus (+)

symbol is used. For instance, Fn+F7 means holding Fn and F7
keys at the same time.

 When a series of clicking actions is needed in a Windows O/S,

the [ ] and > symbols are used. For instance, [Start > Settings >
Control Panel > Display] means clicking the Start icon first, then
the Settings, then the Control Panel, then the Display icon.

 When you need to make a selection with the touch pad (or

mouse), you will be asked to ’select’ or ‘click’ or ‘double-click’,
‘right-click’ the item.

Note: Text in this format and symbol represents specific instructions, commentary,

sidelights, or any additional information or notes that you should be aware of.

Warning: Text in this format and symbol means that failure to comply with the given

instructions or information could result in damage to your computer or could cause

bodily harm or loss of life.

i -5

i -6

Protecting Your Computer - Avoid Abusive Handling and

Adverse Environments

Following the advice below will help ensure that you get the most out

of your investment.

Your computer will serve you well if you take good care of it.

 Do not expose the computer to direct sunlight or place it near

sources of heat.

 Do not subject it to temperatures below 0

o

C (32oF) or above

35

o

C (95oF).

 Do not expose the computer to magnetic fields.

 Do not expose the computer to moisture or rain.

 Do not spill water or liquid on the computer.

 Do not subject the computer to adverse shock and vibration.

 Do not expose the computer to dust and dirt.

 Do not place objects on top of the computer to avoid damaging

the computer.

 Do not place the computer on rocky surfaces.

Here are some ways of taking care of your AC adapter.

 Do not connect the adapter to any devices other than your

computer.

 Do not let water get into the adapter.

 Do not block the ventilation airway of the adapter.

 Keep the adapter in a cool and ventilated place.

 Do not step on the power cord or place heavy objects on top of

it.

 Carefully tuck away the power cord and any cables away from

pedestrian traffic.

 When unplugging the power cord, do not pull on the cord itself;

pull on the plug instead.

i -7

 Keep the adapter away from children.

 The total ampere ratings of the equipment plugged in should

not exceed the ampere rating of the cord if you are using an

extension cord.

 The total current rating of all equipment plugged into a single

wall outlet should not exceed the fuse rating.

 Do not connect another AC adapter to your notebook. This

Notebook uses exclusively the AC adapter: Lishin

LSE0202B2090

(90W), Lishin LSE0202C2090 (90W), Lishin LSE0202D2090 (90W), Liteon

PA-1900-05 (90W), Liteon PA-1900-06 (90W), Liteon PA-1121-22 (120W),

Lishin 0227A20120 (120W).

When cleaning the computer, observe these steps:

1. Power off the computer and remove the battery pack.

2. Disconnect the AC adapter.

3. Use a soft cloth dampened with water. Do not use liquid or

aerosol cleaners.

Contact tech support or see your service technician if any of the

following occurs:

 Computer has been dropped or the body has been damaged.

 Liquid has been spilled into the product.

 The computer does not operate normally.

Cleaning the Ventilation Grills:

It is suggested that you clean the ventilation grills regularly to maintain

optimal thermal regulation of the notebook. To do this, you may use a

soft brush or a vacuum cleaner (with appropriate head adapter) to

remove the dust buildup on the ventilation grills.

i -8

Chapter Summaries

The following is a summary of the available chapters and appendices
in this manual.

Chapter 1: Getting to Know the Basics
In this chapter, you will learn the basic operations and features of
your computer. It gives you a general understanding of the
components of your computer.

Chapter 2: BIOS Setup / Security
In this chapter, you will learn how to change various firmware
settings and what the settings mean. Also, you will learn how to take
advantage of the built-in security feature provided by the BIOS.

Chapter 3: Battery Power & Power Management
In this chapter, you will learn the fundamentals of power
management and how to use them to achieve longer battery life.

Chapter 4: Upgrading Your Computer
In this chapter, you will learn how to upgrade the system memory and
the hard disk drive, and how to install a wireless mini PCI card.

Chapter 5: Troubleshooting
In this chapter, you will learn how to solve common hardware and
software problems.

Appendix A: Product Specification
In this section, you will find a list of the computer’s system
specifications.

Appendix B: Agency Regulatory Notices
In this section, you will find the general electro-magnetic and safety
regulatory information.

Appendix C: Agency Regulatory Notices
In this section, you will find the cyberlink power cinema guide
information.

Ŷ chapter 1 getting to know the basics

1-1

CHAPTERź ONE

GETTING TO KNOW THE BASICS

This chapter introduces the features and

components of the computer.

Ŷ chapter 1 getting to know the basics

1-2

Performance Features



High-Performance Processor

The notebook PC is equipped with a powerful Mobile Intel
Pentium M processor of the latest sub-micron process,
processor technologies, and high bus bandwidths.



Advanced Graphic Engine

The system is assembled with high-performance nVidia GFX
6800 with 256MB DDR. The PCI-Express high-end graphics
engine offers excellent graphics performance for the most
demanding professionals or gamers. The advanced graphics
chip also incorporates a hardware-based motion-compensation
engine, which gives you smooth MPEG video playback. DirectX
9 graphics capability also adds realism to PC games.



LCD Display

The computer is equipped with a wide 17-inch TFT
high-resolution display panel for clear text and brilliant colors.



Expandability

The system offers upgradeable hard disk drive slots and dual
DDRII SDRAM sockets for expansion. This allows the user to
easily increase the storage and system memory capacities as
the need arises.



Built-in Multiple Card Reader

There is a built-in 4-in-1 card reader to access many of the
portable media formats (SD Card, MS Card, MMC Card, and
MS-Pro Card).



Ethernet Port

The system provides a built-in gigabit Ethernet network adapter
for high bandwidth network connection.

Ŷ chapter 1 getting to know the basics

1-3



Firewire (IEEE1394 / 1394a) and USB2.0 ports

In addition to a full array of built-in I/O por

ts, the computer offers

IEEE1394 for ultra high-speed connection to high bandwidth
digital video devices and USB2.0 ports to connect to any
USB-based peripheral devices.



Wireless LAN

The optional internal Wireless LAN module allows your
notebook to connect wirelessly to other 802.11-enabled
systems, devices, or a network.





Built-in Audio Subwoofer

The optional subwoofer gives you enhanced low-frequency

response for audio enjoyment.





Ŷ chapter 1 getting to know the basics

System At A Glance

Top View

1. LCD Latch

The LCD latches lock / unlock the LCD panel.

1-4

Ŷ chapter 1 getting to know the basics

1-5

2. LCD Display

The panel is where the system content is displayed.

3. Keyboard

The keyboard is used to enter data. It has an embedded numeric
keypad and cursor control keys. (See Keyboard Section for
details.)

4. Built-in Microphone

The built-in microphone records sound.

5. Touch Pad

The touch pad is a built-in pointing device with functions similar to
a mouse.

6. Touch Pad Disable / Enable Button

The button enables or disables Touch Pad function.

7. Built-in Stereo Speakers

The built-in speakers output the sound in stereo.

8. Power / Suspend Button

The power/suspend button turns the notebook on and off and it
also acts as a system suspend key. Press momentarily to turn on
the system. Press and hold for at least 4 seconds to turn off the
system. How this key behaves can be defined in the [Start >
Settings > Control Panel > Power Options > Advanced] menu.
Press the power / suspend button again to return from the suspend
mode. (See Chapter 3 for more details on system suspend
function.)

9. LED Status Indicator

The LED Status indicators reveal the status of these functions:
Numeric keypad, cap lock, scroll lock, WLAN module enabling and

Ŷ chapter 1 getting to know the basics

disabling and also the ODD and HDD activities. (See the LED
Status Indicator Section for details.)
The LED Status indicators also reveal the status of the system
power state and battery-charging state. See the LED Status
Indicator Section for details.

10. Silent Mode Button

Pressing the key enables the system to lower its power usage;
therefore the fan speed is reduced to achieve the lowest operating
noise.
You may need to go to BIOS Setup to enable Silent Mode for this
button. See Chapter 2 for details.

11. Outlook Express Quick Key

Pressing the button launches Outlook Express in Windows.

12. Internet Explorer Quick Key

Pressing the button launches Internet Explorer in Windows.

13. Power Cinema Multimedia Player Launch Key (Optional)

The key allows you to watch movies files, listen to music, or view
photos in the optical drive or hard disk drive without having to boot
to Windows.
Or it is a Windows media player launch function instead if you do
not have Linux software.

Note: The way the Power Cinema software works is that when the quick key is

pressed (when the system is in Power-Off mode), the system boots to a

Linux-based O/S and media player application in a separate hard drive partition.

1-6

Ŷ chapter 1 getting to know the basics

Front and Rear Views

Warning: Do not place any heavy objects on the top of the notebook. This may

damage the display.

1. Wireless On/Off Switch

Use the Switch to disable or enable the Wireless function.

2. Consumer IR Receiver

This is where the input from the Remote Control is received.

3. Modem Port

This is where you plug the phone jack (RJ-11) for fax/modem

functions.

4. Battery Pack

The battery pack is a built-in power source for the notebook.

5. Ventilation Grill

The fan grill is where air is exchanged to dissipate the internal heat.

Do not block this airway completely.

1-7

Ŷ chapter 1 getting to know the basics

1-8

6. DVI-I Port

The DVI-I video output port is for connecting the external LCD

monitor or projector.

7. TV (S-Video) Port

The S-Video port permits you to redirect the screen output to a

television set or any analog video playback device. This TV Port is

copyright protected; when a DVD movie is played, the output is

scrambled to prevent analog recording.

Ŷ chapter 1 getting to know the basics

Side Views

Warning: Do not place any heavy objects on the top of the notebook. This may

damage the display.

1. Audio Volume Dial

Use the volume dial to control the loudness of the speakers.

2. Stereo Headphone / SPDIF-out Jack

The stereo headphone jack (3.5-mm diameter) is where you

connect the headphones or external speakers. Alternatively, you

may connect the SPDIF output to an external DTS, AC3, or PCM

sound processor / decoder in your home stereo system.

3. Microphone Jack

The microphone jack (3.5-mm diameter) is where you connect a

microphone.

1-9

4. Optical Drive and Disk Eject Button and Manual Eject Key

Ŷ chapter 1 getting to know the basics

1-10

Hole

If your computer comes with the Combo drive, DVD-RW,

DVD+RW, or DVD-Dual drive, you may save data onto a CD-R /

CD-RW or DVD RW disc. Press the eject button to eject the disk

tray. The manual eject keyhole allows you to manually eject a

jammed disk.

5. USB2.0 Port (x1)

The Universal Serial Bus (USB2.0-compliant) port allows you to

connect a wide variety of devices to your computer at a rate of up

to 480 Mbps. This port conforms to the latest USB2.0

plug-and-play standards.

6. Power Jack (DC-in)

The DC-out jack of the AC Adapter connects here and powers the

computer.

7. Kensington Lock Key Hole

A Kensington-type security lock latches to this keyhole for

anti-theft purposes.

8. Ethernet / LAN Port

The port connects to a network hub via the RJ-45 cable and also

conforms to 10/100Base-TX transmission protocol.

9. 4-in-1 Card Reader

The 4-in-1 Card Reader supports SD Card, MS Card, MMC

Card, and MS-Pro Card.

10. Firewire / IEEE1394 / 1394a Port

This is a high-speed serial data port. You may connect any

Firewire-ready device to this port.

Ŷ chapter 1 getting to know the basics

11. USB2.0 Port (x3)

The Universal Serial Bus (USB2.0-compliant) port allows you to

connect a wide variety of devices to your computer at a rate of up

to 480 Mbps. This port conforms to the latest USB2.0

plug-and-play standards.

12. Express Card Slot (Type II)

The slot is where the Express Card (Type II) is inserted.

Note:

For safety consideration, please insert the dummy card when not using the

Express card.

1-11

Ŷ chapter 1 getting to know the basics

Bottom View

1. Battery Pack and Battery Latch

The battery pack is a built-in power source for the notebook. Slide
the battery latch to release the battery pack.

1-12

Ŷ chapter 1 getting to know the basics

2. Hard Disk Drive Cover

The system’s hard disk drive is located under the cover. The HDD

can be upgraded to a larger capacity. (See Chapter 4 for

instructions on an HDD upgrade.)

3. System Device Cover

The system’s processor with cooler assembly, Wireless LAN

module and DDR memory module are located under the case

cover. The system memory can be upgraded to a larger capacity.

(See Chapter 4 for instructions on a memory upgrade.)

4. Audio Subwoofer

The built-in audio subwoofer gives you enhanced bass response.

5. Ventilation Grill

The fan grill is where air is exchanged to dissipate the internal heat.

Do not block this airway completely.

Warning: Do not block the Fan Grill outlet. Place the machine on hard surfaces

only. The bottom case may get very hot.

1-13

Ŷ chapter 1 getting to know the basics

AC Adapter

1. DC-out Connector

The DC-out connector docks to the power jack (DC-in) on the
computer.

2. Adapter

The adapter converts alternating current into constant DC voltage
for the computer.

3. AC Plug

The AC plug plugs to the AC wall outlet.

1-14

Warning: Make sure you are using a standard 3-prong AC wall socket with a

ground pin. If not, you may feel a slight tingling sensation on any of the computer’s

metal parts such as the I/O ports. This is caused by leakage current when the AC

adapter is not properly grounded (via the ground pin). However, the amount of

leakage current is within the safety regulation and is not harmful to the human body.

Ŷ chapter 1 getting to know the basics

LED Status Indicator

The LED Status Indicator displays the operating status of your
notebook. When a certain function is enabled, an LED will light up.
The following section describes its indication.

System & Power Status Indicators

LED Graphic

Symbol

Indication

Blue light indicates the system is ON.

Blue light indicates the WLAN module is
active.

Blinking blue light indicates the notebook
is in suspend mode.

Blinking orange light indicates the battery
is being charged.

Blinking red light indicates the battery level
is low.

Blue light indicates the hard drive and/or
optical drive is being accessed.

Blue light indicates the numeric keypad is
activated.

Blue light indicates the cap-lock is
activated.

Blue light indicates the scroll-lock is
activated.

Blue light indicates the Silent Mode is
enabled.

1-15

Ŷ chapter 1 getting to know the basics

Keyboard Features

Function Keys (Quick Keys)

Graphic Symbol Action System Control

Fn + F1 Enters Suspend Mode.

Fn + F3 Turns the battery warning beep

off or on.

Fn + F4 Changes Display Mode:

LCD-only, CRT-only and
LCD&CRT.

Fn + F5 Turns Speaker Volume up.

Fn + F6 Turns Speaker Volume down.

Fn + F7 Increases Display Brightness.

Fn + F8 Decreases Display Brightness.

Fn + F10 Press Fn+F10 to enter the

Turbo Mode. The CPU speed
will increase by 10%.

Press Fn+F10 again to exit the
Turbo Mode. The CPU speed

will return to normal.
Fn + Num
Lock

Enables the embedded keypad

to work in numeric mode. The

keys act like numeric keypads

in a calculator. Use this mode

when you need to do a lot of

numeric data entry. An

alternative would be to connect

an external numeric keypad.
Fn + Scroll
Lock

Press the Scroll Lock key and

then press Ĺor Ļto move one

line up or down.

For various system controls, press the Fn (Function) key and the Fx key
simultaneously.

1-16

Ŷ chapter 1 getting to know the basics

Windows Keys

Your keyboard also has two Windows keys:

1. Start Key

This key allows you to pull up the Windows Start Menu at the

bottom of the taskbar.

2. Application Menu Key

This key brings up the popup menu for the application, similar

to a click of the right mouse button.

Embedded Numeric Keypad

Press Fn+NumLock to enable the embedded numeric keypad. The

numbers are printed in the upper right corner of a key, in a color

different from the normal characters. This key pad is complete with

arithmetic operators (+, -, * , /).

Press Fn+NumLock to revert to normal character keys.

789

456

123

*

-

+

.

/

0

Enter

Num
Lk

1-17

Ŷ chapter 1 getting to know the basics

1-18

Touch Pad

The built-in touch pad, which is a PS/2-compatible pointing device,
senses movement on its surface. As you move your fingertip on the
surface of the pad, the cursor responds accordingly.

The following items teach you how to use the touch pad:

1. Move your finger across the touch pad to move the cursor.

2. Press buttons to select or execute functions. These two buttons
are similar to the left and right buttons on a mouse. Tapping on the
touch pad twice is similar to clicking the left button of a mouse.

Function Left Button Right

Button

Equivalent Tapping Action

Execution Click twice

quickly

Tap twice (at the same speed as
double-clicking

the mouse button)
Selection Click once Tap once
Drag Click and hold

to drag the
cursor

Tap twice quickly and on the

second tap hold finger to the touch

pad to drag the cursor
Access
Context Menu

Click once

Move One
Page Up or
Down

Tips on Using the Touch Pad:

1. The double-click speed is timed. If you double-click too slowly,
your notebook responds as if you single-clicked twice.

2. Keep your fingers dry and clean when using the touch pad. Also
keep the surface of touch pad clean and dry to prolong its life.

3. The touch pad is sensitive to finger movements. Hence, the
lighter the touch, the better the response. Heavy touch does not
produce a better response.

Ŷ chapter 1 getting to know the basics

Graphic Subsystem

Your computer uses a high performance 17-inch active matrix TFT
panel with high resolution and multi-million colors for comfortable
viewing. The nVidia NV42M video graphics accelerator, which is
Microsoft DirectX 9-compatible, performs graphics rendering at a
lighting-fast speed.

Adjusting the Display Brightness

The notebook uses special key combinations, called hot keys, to
control brightness.
Press Fn+F7 to increase the brightness.
Press Fn+F8 to decrease the brightness.

Note: To maximize your battery operating time, set the brightness to the lowest

comfortable setting, so that the internal backlight uses less power.

1-19

Extending the Life of the TFT Display Device

Observe the following guidelines to maximize the life of the
backlight in the display.

1. Set the brightness to the lowest comfortable setting
(Fn+F8).

2. When working at your desk, connect your notebook to an
external monitor and disable the internal display Fn+ F4.

3. Do not disable the suspend time-outs.

4. If you are using AC power and have no external monitor
attached, change to suspend mode when not in use.

Ŷ chapter 1 getting to know the basics

Opening and Closing the Display Panel

To open the display, push the LCD latch inwardly and lift up the lid.
Then tilt it to a comfortable viewing position.

To close the display cover, fold it down gently until the LCD latches
click into place.

Warning: To avoid damaging the display, do not slam it when closing. Do not

place any object on top of the computer when the display is closed

1-20

Ŷ chapter 1 getting to know the basics

1-21

Audio Subsystem

Your computer’s audio subsystem is Sound Blaster Pro-compatible.

Adjusting the Volume Manually

To increase the volume, press Fn+F5.

To decrease the volume, press Fn+F6.

Adjusting the Audio Volume in Windows

1. Click the speaker symbol in the task tray in Windows.

2. Drag the volume control bar up or down to adjust the volume.

3. To temporarily silence the speaker without changing the volume

setting, click Mute.

Voice Recording

A built-in microphone allows you to record sound. You will need to

use audio processing software to enable the built-in microphone.

For example, you may use Microsoft Sound Recorder.

Ŷ chapter 1 getting to know the basics

Modem

Your computer comes with a 56K V.92 internal fax/modem and a phone
jack (RJ-11), which is located on the left side of your computer.
Use a telephone cable to connect the computer to the telephone wall
outlet.

Connecting the Modem

1. Plug one end of the phone line into the modem port located on
the rear side of the computer. (For EMI compliance, you need to clip
the included EMI CORE to the phone line.)

2. Plug the other end of the line into the analog phone wall outlet.

Depending on where your computer is used, you may need to change
settings in the modem. Correct settings will allow you to maintain a stable
connection in a country with a telecommunication system that may be
different to others.

To change the modem setting, do the following:

1. Go to [Start > Settings > Control Panel] and double-click on the
Modem Settings icon. You will see a similar dialog box.

2. Click on the pull-down menu and select the country where it is

1-22

Ŷ chapter 1 getting to know the basics

1-23

applicable. Click on OK to exit.

Ŷ chapter 1 getting to know the basics

Ethernet

Your computer is equipped with a 100/1000Base-TX Fast Ethernet

network adapter. Connect the active LAN cable to the RJ-45 LAN port

located on the left side of the computer. This allows you to access and

transmit data in the local area network.

Connecting to the Network

Use the Unshielded Twisted Pair (UTP) Ethernet cable only.

1. Insert one end of the UTP cable into the network connector

until the connector snaps securely into the receptacle.

2. Either connect the other end of the cable to an RJ-45 jack

wall outlet or to an RJ-45 port on a UTP concentrator or hub in the

network.

Cabling Restriction for Networks

The following restrictions should be observed for

100/1000BASE-TX networks:

 The maximum cable run length is 100 meters(m) (328

feet[ft]).

 For 100/1000-Mbps operations, use Category 5 wiring and

connections.

Note: Consult the Windows manual and / or Novell Netware user’s guide for the

software installation, configuration, and operation of the network.

1-24

Ŷ chapter 2 bios setup and security feature

2-1

CHAPTERź TWO

BIOS SETUP AND SECURITY FEATURE

In this chapter, you will learn how to enter the
BIOS Setup Menu and manipulate various
hardware control settings. You will also learn how
to use the built-in security features.

Ŷ chapter 2 bios setup and security feature

2-2

The Setup Utility is a hardware configuration program built into your

computer’s BIOS (Basic Input/Output System). It runs and maintains

a variety of hardware functions. It is a menu-driven software, which

allows you to easily configure and change the settings.

The BIOS contains manufacture’s default settings for the computer’s

standard operations. However, there are occasions when you may be

required to modify the default settings in the BIOS. For example, you

may need to configure the BIOS power management (APM) settings

if you are using DOS, or non-Windows operating system.

The BIOS allows you to set up passwords to limit access to users.

This is an important feature because a great deal of vital information

is carried within the computer nowadays. Unauthorized access can

be prevented. Later in this chapter, you will learn how to use this

security feature.

Ŷ chapter 2 bios setup and security feature

Entering the BIOS Setup Screen

First turn on the power. When the BIOS performs the POST
(Power-On Self Test), press F2 key quickly to activate the AMI BIOS
Setup Utility.

Note: You may need to press F2 key fairly quickly. Once the system begins to load

Windows, you may have to retry by cycle-power on again

Leaving the BIOS Setup Screen

When you have finished modifying the BIOS settings, exit the BIOS. It
takes a few seconds to record changes in the CMOS.

BIOS Action Keys

Function Key Command Description

ESC Exit

Leaves a sub-menu to return to the
previous menu OR exits the BIOS setup
while saving changes.

Enter Go to Sub Screen Shows the Sub Menu

F1 General Help Shows the Help Screen

F10 Save and Exit

Saves changes and reboots the
computer.

<Tab> Select a field Selects the next field.

Ĺ Select an item Selects the next upper item.

Ļ Select an item Selects the next lower item.

- Lower value Selects the next value within a field.

+ Higher value Selects the next value within a field.

2-3

Ŷ chapter 2 bios setup and security feature

Modifying the BIOS Settings

The AMIBIOS setup main menu is subdivided into sub-menus. Each
menu item is described in this section.

Main Setup

Under this menu, you may change time/date and view basic
processor and system memory information.

Item Selections /

Sub-menu

Description

Date N/A Type in the current date, in MM/DD/YY

format.

Time N/A Type in the current date, in HH:MM:SS

format.

Advanced Setup

ŹIDE Configuration

Item Selections /

Sub-menu

Description

Secondary
IDE
Master

ATAPI CDROM The secondary master controls the

ATAPI CD-ROM drive.

Note: The sub-menu is not selectable. Press enter to view information of the storage

device.

2-4

Ŷ chapter 2 bios setup and security feature

2-5

Item Selections /

Sub-menu

Description

Remote
Control

Enable
Disable

Enable or Disabled the remote control IR
port

CPU
Execute-D
isable-Bit

Enable/Disable When enabled the CPU will provide the

system with protection from viruses that

use the over run buffer vulnerability.
LCD Panel
power
Saving

Enable/Disable When enabled dims the LCD in long

batter life mode to conserver power.

Security Setup

ŹBoot Settings Configuration

Item Selections /

Sub-menu

Description

Change
Supervisor
Password

N/A Install or Change the Password

Change
User
Password

N/A Install or Change the Password

Clear User
Password

N/A Install or Change the Password

Using Password Protection

Two Levels of Password Protection are available. The BIOS provides
both a Supervisor and a User password. If you try to activate both
passwords, the Supervisor password must be set first.

Ŷ chapter 2 bios setup and security feature

The passwords activate two different levels of protection:

1. System always asks for password every time it is powered on.

2. System asks for password only when you attempt to enter BIOS
utility.
The passwords are encrypted and stored in NVRAM. Make sure you
write them down or memorize them. If you lost the passwords, the
computer may need to be sent back to the factory or to an authorized
service dealer to reset the passwords.

Power Setup

Item Selections /

Sub-menu

Description

Long Battery
Life Mode

Enable
Disable

[When enabled, maximum battery
life can be achieved. The processor
performance is lowered.

Note: The Suspend Mode selection in BIOS only applies to older Windows version

(such as Windows 3.1 or Windows 95 or NT4) or non-Windows operating system. In

Windows ME / 98SE / 2000 / XP, suspend mode and settings are determined by

settings in the Power Options Properties (Start > Control Panel > Power Options).

2-6

Ŷ chapter 2 bios setup and security feature

Boot Setup

Item Selections /

Sub-menu

Description

Quiet Boot Disabled

Enabled

When Enabled, the system will display

OEM logo instead of the POST

messages.

When Disabled, the system will display

POST messages (i.e. devices

information.)

ŹBoot Device Priority

Item Selections /

Sub-menu

Description

1st Boot
Device

Set the type of device for the 1st drive

BIOS attempts to boot from. If Realtek

Boot Agent is selected, system will

attempt to load boot sector from the

Ethernet port.

2nd Boot
Device

Set the type of device for the 2nd drive

BIOS attempts to boot from.

3rd Boot
Device

Set the type of device for the 3rd drive

BIOS attempts to boot from.

4th Boot
Device

Removable Dev.
CD/DVD
Hard Drive

Realtek Boot
Agent
Disabled

Set the type of device for the 4th drive

BIOS attempts to boot from.

Note: If you select Realtek Boot Agent, the system will attempt to boot from the

network.

Note: When the BIOS performs POST, you may also press F12 Key to enable the

Boot Device selection menu. You may choose CD/DVD, Hard Drive, or Realtek Boot

Agent as the first storage device to boot from. If you have already connected a USB

Floppy Disk Drive before powering up, it will appear as a Removable Device in the Boot

Device selection menu

2-7

Ŷ chapter 2 bios setup and security feature

2-8

Exit Setup

Item Selections /

Sub-menu

Description

Saves
Changes and
Exit

N/A After you have completed the BIOS

settings, select this item to save all
settings, exit BIOS Setup utility, and
reboot. New system settings will take
effect on next power-up. F10 key can be
used for this operation.

Discard
Changes

N/A Discards changes done so far to any of

the setup questions.

Load Optimal
Defaults

N/A Load Optimal Default value for all the

setup questions. F9 key can be used for
this operation.

Ŷ chapter 3 battery power & power management

3-1

CHAPTERź THREE

BATTERY POWER & POWER

MANAGEMENT

In this chapter, you will learn the fundamentals of
power management and how to use it to achieve
longer battery life.

Ŷ chapter 3 battery power & power management

In this chapter, you will learn how to operate your notebook on

battery power, how to handle and maintain the battery pack, and learn

about the system’s power saving features.

The TFT display, central processor, and hard disk drive are the major

hardware subsystems that consume the most power. Power

management dictates how these key components should behave to

conserve power. For example, you can have the system turn off its

display after 2 minutes of inactivity to save power. Efficient power

management can help you work longer sessions before having to

recharge the battery.

The Battery Pack

Lithium-Ion Battery

Your notebook uses an eight-cell Lithium-Ion battery pack that

provides power when you don’t have access to an AC outlet.

Note: It is necessary that you charge the battery pack for at least 6 hours

before using it for the first time.

Note: In the Standby Suspend mode, a fully charged battery loses its power

in roughly 1/2 day or less. When not being used, the battery’s power will

deplete in 1-2 months.

3-2

Ŷ chapter 3 battery power & power management

Battery Low-Power Warning

1. Low Battery Warning

Low battery condition occurs when battery power is reduced

to 6%. The red battery status LED indicator blinks and the

system beeps once every 16 seconds or so.

2. Very Low Battery Warning

Very Low battery condition occurs at 3% power remaining.

The red battery status LED indicator blinks and the system

beeps at 4-second intervals.

When the notebook warns you of its low battery condition, you

will have about 3-5 minutes to save your current work.

Warning:

Do not expose battery packs to temperatures below 0 degrees

Celsius (32 degree F) or above 60 degrees C (140F). This may adversely

affect the battery pack.

3-3

Note:

Press Fn+F3 to turn off the battery warning beep.

Ŷ chapter 3 battery power & power management

Installing and Removing the Battery Pack

To Remove the Battery Pack:

1. Place the notebook bottom-side up on a flat and secure

surface.

2. Push the latch and pull the battery’s hard case away from

the notebook.

3-4

Ŷ chapter 3 battery power & power management

To Install the Battery Pack:

1. Place the notebook bottom-side up on a flat and secure

surface.

2. Carefully insert the battery pack into the battery

compartment of the notebook.

Charging the Battery and Charging Time

To charge the battery, while the battery pack is in the notebook,

plug the AC adapter into the notebook and an electrical outlet.

The charging time is approximately 4-6 hours when the notebook

is turned off and approximately 6-10 hours when the notebook is

turned on.

When the battery is fully charged, the battery charge indicator

becomes dark.

Note: If the system runs at heavy loading or in a high temperature environment,

the battery may not be fully charged. You need to continue to charge it with the AC

adapter plugged in until the charging LED turns dark.

3-5

Ŷ chapter 3 battery power & power management

Checking the Battery Level

You can check the remaining battery power in the Windows battery
status indicator, which is located at the lower right-hand corner of
the task bar. (If you do not see a battery or AC-in icon on the task
tray, go to the Power Options Properties box and click on the
Advanced tab. Check off ``Always show icon on the task bar``.)
Alternatively, you can access the power meter by clicking the
Power Options icon in the Windows Control Panel.

Prolonging the Battery’s Life and Usage Cycles

There are things you can do to prolong the use of the battery.

 Use the AC adapter wherever an AC wall outlet is available.
This will ensure uninterrupted computing.

 Purchase an additional battery pack.
 Store the battery pack in room temperature. Higher

temperatures tend to deplete the battery’s power faster.
 Make good use of the power management function. Save To
Disk (Hibernate) saves the most energy by storing current system
contents in a hard disk space reserved for this function.
 The life expectancy of the battery is approximately 300
recharges.
 See the notices section in the beginning of the user manual on
how to care of the battery pack.

3-6

Note: Read the section Protecting Your Notebook in the beginning of this manual

for tips about how to maintain the battery pack.

Note: To achieve optimal battery performance, you may need to do a battery

calibration at a 3-month interval. To do this:

1. Fully charge the battery.

2. Then discharge the battery by entering the BIOS setup screen. (Press F2

key as soon as you turn on the computer. And let it remain at the setup screen

until the battery runs out.

3. Fully charge the battery again.

Ŷ chapter 3 battery power & power management

3-7

Using Windows Power Options

Windows Power Management provides basic power saving

features. In the Windows Power Options Properties [Start >

Settings > Control Panel > Power Options] dialogue box, you may

enter time-out values for the display and hard disk drive. Windows

power manager saves power by turning off the hard drive after 1

minute of inactivity, for example.

Windows’ Power Schemes

The power management control panel in Windows XP, known

as Power Schemes, is designed to provide the user with an

easy-to-use interface. The Power Schemes tab can be found

in the Power Options Properties panel that is accessible via

the control panel window.

Schemes are easy to understand, based on notebook usage

scenarios, and control not only processor power usage but

other system peripherals as well.

Go to [Start > Settings > Control Panel] and double-click the

Power Options icon.

Always on mode puts the processor into maximum

performance mode, which provides no power saving. The

other schemes control processor performance based on

demand. For example, Max Battery mode lowers the

processor’s speed and voltage to conserve power as much as

possible.

Ŷ chapter 3 battery power & power management

In this dialog box, you can manually set the LCD and hard

drive’s time-out values in the Plugged in column and in the

Running on batteries column. Lower time-out values will save

more battery power.

Note: Also consult the Windows user guide for more information on how to

use Windows power management functions.

Note: Actual dialogue box may appear slightly different from what is shown

above.

3-8

Ŷ chapter 3 battery power & power management

3-9

Suspend Mode

Standby Suspend

The system automatically enters this mode after a period of

inactivity, which is set in the Power Schemes dialog box. In

Standby mode, hardware devices, such as the display panel

and hard disk, are turned off to conserve energy.

Hibernate Suspend

In this mode, all system data is saved in the hard disk before

powering down. When this mode is activated, all system state

and contents are saved to the hard disk drive after a period of

inactivity defined by the user. No power or very little power is

drawn from the battery module under this mode.

However, depending on how much RAM has been installed

on your computer, the amount of time the system requires to

restore all its previous contents can range from 5 to 20

seconds.

For Windows 2000 / XP users, hibernation is handled by the

operating system; therefore, no special disk partition or disk

file is necessary.

If you wish to activate Hibernate mode, you need to enable

Hibernate Support in the Hibernate tab of the Power Options

menu.

Ŷ chapter 3 battery power & power management

Note: Do not install or remove the memory module when the system is in

the suspend mode.

Note: Actual dialogue box may appear different from what is shown above.

3-10

Ŷ chapter 3 battery power & power management

Power Button Action

The notebook PC’s power button can be set to turn off the
system or activate the suspend mode.

Go to [Start > Settings > Control Panel > Power Options] and
click on the Advanced tab. In the pull-down menu, select how
you wish the power button to work as.

Note: Actual dialogue box may appear different from what is shown above.

Warning: In the When I close the lid of my portable computer pull-down

menu, DO NOT select Do nothing – otherwise the system will still run at high

speed while the processor’s fan grill is fully blocked by the closed LCD panel.

The heat will damage the LCD panel.

3-11

Ŷ chapter 3 battery power & power management

Low Battery Warning

You can define when and how the system warns you of its

battery-low condition.

Go to the Alarms tab in the Power Options Properties box. If

you wish to hear audible beeps, click on the Alarm Action

button and put a check on Sound Alarm.

Note: Consult the Windows user guide for more information on how to use

Windows power management functions.

Note: Actual dialogue box may appear different from what is shown above.

3-12

Ŷ chapter 3 battery power & power management

3-13

Ŷ chapter 3 battery power & power management

Power Menu Quick Access

Instead of making specific selections in the Power Options

Properties box, you can quickly and easily specify which

pre-set power saving function you desire by clicking on the

Battery icon at the lower right-hand corner of the task bar. (If

you do not see a battery or AC-in icon, go to the Power

Options Properties box and click on the Advanced tab. Check

off ``Always show icon on the task bar``.) Select Max Battery if

you want the system to enter suspend mode more often. Or,

select Always On if your notebook PC is plugged into an AC

power source.

Note: Actual dialogue box may appear different from what is shown above.

3-14

Ŷ chapter 4 upgrading your computer

CHAPTERź FOUR

UPGRADING YOUR COMPUTER

In this chapter, you will learn how to upgrade the
DRAM and hard disk drive, and how to install the
optional wireless LAN mini PCI.

Warning: We strongly recommend you contact Alienware when

upgrading your system. When upgrading, please turn off the

power, and disconnect the LAN and Modem cable first for your

safety. After the upgrade is complete, please remember to

screw all the screws before turning on the system.

4-1

Ŷ chapter 4 upgrading your computer

Upgrading the Hard Disk Drive

Replacing the original drive with one of larger capacity can increase

the hard drive capacity of your computer. The computer uses a 9.5

mm (height), 2.5-inch Serial ATA type hard disk.

Be sure to make a backup copy of all your data before attempting this

operation.

Warning: A hard drive upgrade is a delicate process. Please observe the following

instructions carefully or have a qualified technician install it for you. Damages due to

mishandling of this procedure are NOT covered by the manufacturer's warranty.

Warning: Apply care when handling the hard disk.

 Do not drop or apply any shock.

 Do not press on the cover.

 Do not touch the connector with your fingertips.

 Mishandling of the hard drive can result in permanent loss of data. Make a

backup copy of the drive‘s content before you remove it.

4-2

Note: Certain models that come with the IBM-brand hard drive emit a clattering sound

when they are being rattled. This is a normal condition.

Ŷ chapter 4 upgrading your computer

Upgrading the Hard Disk Drive

To replace the hard disk drive, do the following:

1. Turn OFF the computer. Unhook the AC cord and all

cables/devices attached to the notebook. Remove the battery.

2. Place your hand on a large metal object momentarily to

discharge any static electricity.

3. Locate and remove two Screw A’s.

4. Remove HDD Cover.

5. Locate and remove two Screw B’s.

4-3

Ŷ chapter 4 upgrading your computer

6. Push the HDD module to the right and separate it from the

connector. Lift the module away from the bay.

7. Locate and remove 4 Screw C’s from the HDD module.

Remove the metal case.

8. Re-attach the metal cover to the new hard drive and

tighten 4 Screw C’s. Note the green PC board of the hard disk

drive is facing against the metal case.

9. Re-attach the HDD module to the HDD connector. And

re-attach 2 Screw B’s.

4-4

Ŷ chapter 4 upgrading your computer

4-5

10. Put the HDD cover back and re-attach 2 Screw A’s.

Congratulations! You have now completed the hard drive upgrade.

When you boot up the PC, you may need to create a primary HDD

partition and reformat the new drive and re-install the O/S, drivers,

and all the necessary applications.

Ŷ chapter 4 upgrading your computer

Upgrading the System Memory

Many applications will generally run faster when the computer’s

dynamic memory capacity is increased. The computer provides two

DDR2 memory sockets, located underneath the System Device

Cover. You can increase the amount of memory by replacing the

existing one with a dual inline memory module (commonly known as

SO-DIMM) of a higher capacity. The SO-DIMM can be 128MB,

256MB, 512MB, or 1024MB in capacity. The SO-DIMM is of type

DDR2 SDRAM, has 200 pins and runs on 2.5V. The SO-DIMM should

be PC2 3200 or PC2 4200 compliant.

4-6

Warning: A memory upgrade is a delicate process. Please observe the following

instructions carefully or have a qualified technician install it for you. Damages due to

mishandling of this procedure are NOT covered by the manufacturer's warranty.

Warning: Changing memory while your computer is in suspend or power-saving

mode may cause permanent damage to the hardware. Make sure you turn off the

power and unplug the AC cord before proceeding with a memory upgrade.

Warning: You should only use the DIMM module that is approved by Alienware;

otherwise the system may become unstable.

Ŷ chapter 4 upgrading your computer

Installing a memory module (DIMM) into the system

To install the DIMM, do the following:

1. Power OFF the notebook. Unplug the AC cord and all

cables/devices attached to the notebook. Remove the battery.

2. Place your hand on a large metal object momentarily to

discharge any static electricity. Place the notebook on a flat

surface and fully close the LCD lid.

3. Locate and remove 6 Screw C’s on the System Device

Cover.

Screw C x4

S crew C x 2

System
Device Cover

4. Remove the System Device Cover. The DIMM socket is now
seen as shown below.

4-7

Ŷ chapter 4 upgrading your computer

Dual DDR
DIMM Sockets

5. If you need to remove an old DIMM from the socket, press

out on the latches located on both edges of the socket at the same

time. The DIMM should pop up to an angle of 30 degree (see

diagram below). Pull the DIMM module out of the memory socket.

Store away the DIMM for the future use.

6. Install the new DIMM module into the memory socket.
The DIMM will only fit in one orientation. Insert the DIMM at an
angle of approximately 30 degrees into the empty memory socket.
Then press it firmly so that the contact edge is driven into the
receiving socket.

4-8

Ŷ chapter 4 upgrading your computer

Notch

7. Pivot the DIMM until the latches on both sides of the
socket snap into place.

Note: Notice the notch on the DIMM. The notches should fit nicely with the socket.

8. Put the System Device Cover back and tighten 6 Screw
C’s.

Congratulations! You have just completed the memory upgrade.
When you boot up the computer, you should expect to see an
increase in DRAM capacity.

Note: Your computer has been tested with a wide range of DIMM on the market.

However, not all memory modules are compatible. Check with your system vendor

for a list of compatible DIMM for your computer.

4-9

Ŷ chapter 4 upgrading your computer

Adding a Mini-PCI Type Wireless LAN Card
(Optional Device)

Your computer comes with a unique Mini PCI Card socket, which is
located next to the DRAM socket and underneath the WLAN Module
Cover. The socket allows the computer to add unique features such
as wireless LAN (IEEE802.11x). Ask an Alienware customer service
agent on the availability of the mini PCI card.

Warning: Installing a mini PCI card is a delicate process. Please observe the

following instructions carefully or have a qualified technician install it for you. Damages

due to mishandling of this procedure are NOT covered by the manufacturer's warranty.

Warning: Installing the mini PCI card while your computer is in suspend or

power-saving mode may cause permanent damage to the hardware. Make sure you

turn off the power and unplug the AC cord before proceeding with a memory upgrade.

4-10

Ŷ chapter 4 upgrading your computer

Installing a Mini PCI Card into the System

To install a new Mini PCI card, do the following:

1. Follow steps in the previous section, Installing a memory

module (DIMM) into the system, to access the Mini PCI Socket.

Mini PCI
Soc ket

Antenna Cable
with Connector

2. The mini PCI card will only fit in one direction. Align the

small notch in the module with the socket on the connector and

insert the card at an angle of approximately 30 degrees into the

empty socket. Then press it firmly so that the contact edge is

driven into the receiving socket. Pivot the mini PCI card until the

latches on both sides of the socket snap into place.

4-11

Ŷ chapter 4 upgrading your computer

Note: If you want to remove a mini PCI card from the socket, press out on the

latches located on both edges of the socket at the same time. The card should pop

up to an angle of 30 degree.

3. Locate 2 antenna cables with connectors. Snap the cable

onto the golden connector on the Mini PCI Wireless LAN card.

(Note: The connectors are fairly small! This may take some

maneuvering. You may want to connect the antenna cables before

inserting the wireless card into the socket. )

Mini PCI
Socket

Mini PC

I

Wireless
Card

Connectors

4. Replace the System Device Cover and 6 Screw C’s.

Congratulations! You have now completed the mini PCI card

installation. During the next time the system boots to Windows, the

system will prompt for driver location. Insert the Factory CD-ROM

and point to the directory where the Wireless LAN driver can be

found. In addition to installing the driver, you may also need to run

a Setup.exe program to install the card’s utility applications before

it is fully operational.

4-12

Ŷ chapter 5 troubleshooting

5-1

CHAPTERź FIVE

TROUBLESHOOTING

In this chapter, you will learn how to solve

common hardware and software problems.

Ŷ chapter 5 troubleshooting

5-2

Your computer has been fully tested and complies with the system

specifications before shipping. However, incorrect operations and/or

mishandling may cause problems.

This chapter provides a reference for identifying and correcting

common hardware and software problems that you may encounter.

When you encounter a problem, you should first try to go through the

recommendations in this chapter. Instead of returning the computer

and waiting for repair, you may easily solve the problems by

considering the following scenarios and possible solutions. If the error

continues, contact your reseller for service information.

Before taking further actions, consider the following

suggestions:

 Check to see if the problem persists when all the external

devices are removed.

 Check to see that the green light indicator on the AC adapter

is lit.

 Check to see the power cord is properly plugged to the wall

outlet and to the computer.

 Check to see the power indicator of the computer is on.

 Check to see if your keyboard is operational by pressing and

holding any key.

 Check for any incorrect or loose cable connections. Make

sure the latches on the connectors latch securely on to the receptor

end.

 Be sure you have not performed an incorrect setting on the

Ŷ chapter 5 troubleshooting

5-3

hardware devices in the BIOS Setup utility. A faulty setting may

cause the system to misbehave. If you are not sure of the changes

you made, try to restore all the settings to factory defaults.

 Be sure all the device drivers are installed properly. For

example, without the audio driver properly installed, the speakers

and microphone will not work.

 If external devices such as an USB camera, scanner, or

printer do not function correctly when connected to the system, it is

usually the device’s own problem. Consult the device’s

manufacturer first.

 Some software programs, which have not gone through

rigorous coding and testing, may cause problems during your

routine use. Consult the software vendor for problem solving.

 Legacy peripheral are not plug-and-play capable. You need to

restart the system with these devices powered up and connected

first.

 Be sure to go to BIOS SETUP and load DEFAULT SETTING

after BIOS re-flash.

 Be sure the Quick Key Lockout Switch on the bottom of the

computer is not engaged; otherwise, the quick keys will not work.

Ŷ chapter 5 troubleshooting

5-4

Audio Problems

No speaker output -

 Turn up the volume dial located at the right edge of the

computer. See Chapter 1 for its location.

 Software volume control is turned down in Microsoft

Sound System or is muted. Double-click the speaker icon on the

lower right corner of the taskbar to see if the speaker has been

muted or turned down all the way.

 Most audio problems are software-related. If your

computer worked before, chances are software may have been

set incorrectly.

 Go to [Start > Settings > Control Panel] and double-click

the Sounds and Audio Devices icon. In the Audio page, make

sure that Vinyl AC’97 Audio (WAVE) is the default playback

device.

Sound cannot be recorded -

 Double-click the speaker icon on the lower right corner of

the taskbar to see if the microphone has been muted.

1. Click Options and select Properties.

2. Select Recording and click the OK button.

3. After Click OK button, the recording volume control panel

will appear.

 Go to [Start > Settings > Control Panel] and double-click

the Multimedia icon (or Sounds and Audio Devices icon). In the

Volume or Audio page, make sure that Vinyl AC’97 Audio

(WAVE) is the default recording device.

Ŷ chapter 5 troubleshooting

5-5

Hard Disk Problems

The hard disk drive does not work or is not recognizable -

 If you had just performed a hard disk upgrade, make sure

the hard drive connector is not loose and the hard disk drive is

also correctly seated. Remove it and reinsert it firmly, and

restart your PC. (Refer to Chapter 4 for details.)

 The new HDD may need to be partitioned and

reformatted. O/S and drivers will need to be re-installed as well.

 Check the hard disk indicator LED. When you access a

file, the LED lamp should light up momentarily.

 The new HDD may be defective or is not compatible.

 If your computer has been subjected to static electricity or

physical shock, you may have damaged the disk drive.

The hard drive is making abnormal whining noises -

 You should back up your files as soon as possible.

 Make sure the source of noise is indeed from the hard

drive and not the fan or other devices.

The hard disk drive has reached its capacity -

 Run Disk Cleanup utility in Windows. [Start > All

Programs > Accessories > System Tools > Disk Cleanup] The

system will prompt you for what to do.

 Archive files or programs that you no longer use by

moving them to an alternative storage medium (floppy disk,

optical record-able disk, etc.) or uninstall programs that you no

longer use.

 Many browsers store files in the hard drive as a cache to

speed up the performance. Check the program’s Online Help for

Ŷ chapter 5 troubleshooting

5-6

instructions on decreasing the cache size or on removing

temporary Internet files.

 Empty the Recycle Bin to create more disk space. When

you delete files, Windows saves them to the Recycle Bin.

The hard disk takes longer to read a file -

 If you have been using the drive for a period, the files may

be fragmented. Go to [Start > Programs > Accessories >

System Tools > Disk Defragmenter] to perform a disk

defragmentation. This operation may take a while.

 Interrupt requests or problems with other hardware

devices may have occupied the CPU and therefore slow down

the system performance.

The files are corrupted -

 Run the Error-checking utility in Windows to check the

HDD. Double-click My Computer. Right-click C: and select

Properties. Click Check Now in Error-checking in Tools.

Ŷ chapter 5 troubleshooting

5-7

Optical Drive Problems

The optical drive does not work -

 Try rebooting the system.

 The disk is damaged or files are not readable.

 After you have inserted a CD-ROM disk, it may take a

moment before you can access its content.

The drive does not read any disks -

 The CD may not be properly seated in the tray. Make sure

the disk is firmly seated onto the spindle.

 The disk is damaged or not readable.

The disk cannot be ejected -

 Normally, it takes a few seconds to eject the disk.

 If the disk cannot be ejected, it may be mechanically

jammed. Straighten out a paper clip and insert it to a tiny hole

next to the eject button. This should reject the disk tray. If not,

return the unit for repair. Do not forcefully pull on the disk tray.

The Combo or DVD RW drive (optional device) cannot

record -

 You need to purchase and install a burner utility program

to record files to a blank media.

Ŷ chapter 5 troubleshooting

5-8

Display Problems

The display panel is blank when the system is turned on -

 Make sure the computer is not in the Standby or

Hibernate suspend modes. The display is turned off to conserve

energy in these modes.

The screen is difficult to read -

 The display resolution should be set to at least 1024x768

for optimal viewing.

1. Go to [Start > Settings > Control Panel] and double-click

the Display icon.

2. Under the Settings page, set the screen resolution to at

least 1024x768 and choose at least 256 colors.

The screen flickers -

 It is normal if the display flickers a few times during

shutting down or powering up.

Ŷ chapter 5 troubleshooting

5-9

Keyboard and Mouse Problems

The built-in touch pad performs erratically -

 Make sure there is no excess perspiration or humidity on

your hand when using the touch pad. Keep the surface of the

touch pad clean and dry.

 Do not rest your palm or wrist on the surface of the touch

pad while typing or using the touch pad.

The built-in keyboard accepts no input -

 If you are connecting an external keyboard to the system,

the built-in keyboard may not work.

 Try restarting the system.

The characters on the screen repeat while I type.

 You may be holding the keys down too long while you’re

typing.

 Keep the keyboard clean. Dust and dirt under the keys

could cause them to stick.

 Configure the keyboard to wait longer before the auto

repeat feature starts. To adjust this feature, go to [Start >

Settings > Control Panel], and double-click the Keyboard icon. A

dialogue box shows up with the adjustable settings for the

keyboard.

Ŷ chapter 5 troubleshooting

5-10

CMOS Battery Problem

A message “CMOS Checksum Failure” displays during the

booting process or the time (clock) resets when booting -

 Try to reboot the system.

 If the message “CMOS Checksum Failure” appears

during the booting procedure even after rebooting, it may

indicate failure of the CMOS battery. If so, you need to replace

the battery. This battery normally lasts two to five years. The

battery is of type CR2032 (3V). You may replace it by yourself.

The battery is located under the System Device Cover on the

bottom of the notebook. See Chapter 4 for more details.

Ŷ chapter 5 troubleshooting

5-11

Memory Problems

The POST does not show an increased memory capacity

when you have already installed additional memory -

 Certain brands of memory modules may not be

compatible with your system. You should ask tech support for a

list of compatible DIMM.

 The memory module may not be installed properly. Go

back to Chapter 4 to review the details of this operation.

 The memory module may be defective.

The O/S issues an insufficient memory error message

during operation -

 This is often a software or Windows-related problem. A

program is draining the memory resources.

 Close the application programs you’re not using and

restart the system.

 You need to install additional memory module. For

instructions, go to Chapter 4 Upgrading Your Computer.

Ŷ chapter 5 troubleshooting

5-12

Modem Problems

The built-in modem does not respond -

 Make sure the modem driver is loaded properly.

 Go to [Start > Settings > Control Panel > Phone and

Modem Options] and go to the Modems tab. Make sure

SmartLink 56K Voice Modem or Uniwill V.92 Modem is listed.

Otherwise, click the Add button to add the modem drive, which

is located in the factory CD-ROM (or floppy diskette).

 Go to [Start > Settings > Control Panel > System] and

click the Device Manager button in the Hardware page to check

for a possible resource or driver conflict. See Windows on-line

help or manual for how to handle such problems.

 Make sure the phone line, which the computer is

connected to, is working.

Connection difficulties -

 Be sure to disable Call Waiting on the phone line.

 Be sure to have the correct country setting where your

computer is used. [Start > Settings > Control Panel > Modem

Settings > Configuration] In the Country/Area pull-down menu,

select the appropriate country setting.

 Excessive line noise might cause the connection to be

dropped. To check this, put the regular phone handset on the

line and place a phone call. If you do hear abnormal noise, try to

make the modem connection with a different line or contact your

local telephony company for service.

 Make sure the cable connection is firm.

 Try a different receiver number and see if the problem

persists.

Ŷ chapter 5 troubleshooting

5-13

Network Adapter / Ethernet Problems

The Ethernet adapter does not work -

 Go to [Start > Settings > Control Panel > System >

Hardware > Device Manager]. Double-click on Network

Adapters and check if Realtek RTL8139/810x Family Fast

Ethernet NIC appears as one of the adapters. If it does not exist,

Windows has not detected the Realtek RTL8139/810x Family

Fast Ethernet NIC or the device driver has not been installed

properly. If there is a yellow mark or red cross on the network

adapter, it may be a device or resource conflict. Replace or

update the device driver from the factory CD-ROM disk or

consult the Windows manual on how to solve the resource

conflict problem.

 Make sure the physical connections on both ends of the

cable are good.

 The hub or concentrator may not be working properly.

Check to see if other workstations connected to the same hub or

concentrator are working.

The Ethernet adapter does not appear to operate in the

100Mbps transmission mode -

 Make sure the hub you are using supports 100Mbps

operation.

 Make sure that your RJ-45 cable meets the 100Base-TX

requirements.

 Make sure the Ethernet cable is connected to the hub

socket that supports 100Base-TX mode. The hub may have

both 100Base-TX and 100Base-T sockets.

Ŷ chapter 5 troubleshooting

ExpressCard Problems

5-14

Note: Some systems may not have the PC Card Slot option.

ExpressCards do not function-

 Make sure you have properly installed the driver for the
card.
 Consult the card’s manual or contact the vendor for
troubleshooting.

The ExpressCards cannot be recognized -

 Windows NT4.0 does not support ExpressCards function.
You may need an external program for this.
 Make sure the card is fully inserted; the outer end of the
card should be even with the edge of the computer.

 Remove and insert the ExpressCards again.
 Make sure there is no IRQ conflict with the card. See

Windows on-line help for solving IRQ conflicts.

 Reboot the computer and see if the problem persists.
 The card may be defective. Try the card on another

system, if possible.

Windows crashes or freezes when you remove the
ExpressCards

Make sure you have stopped the ExpressCards before
removing it. Double-click the Safely Remove Hardware icon at
the lower right corner of the task bar and select the card you
wish to stop. When you click <Close>, Windows will prompt you
to remove the card in a few seconds.

Ŷ chapter 5 troubleshooting

5-15

Performance Problems

The computer becomes hot -

 In a 35

o

C environment, certain areas of the computer’s

back case are expected to reach 50 degrees.

 Make sure the air vents are not blocked.
 If the fan does not seem to be working at high

temperatures (50 degrees Celsius and up), contact the service
center.
 Certain programs that are processor-intensive may
increase the computer temperature to a degree where the
computer automatically slows down its CPU clock to protect
itself from thermal damage.

The program appears stopped or runs very slowly -

 Press CTRL+ALT+DEL to see if an application is still
responding.

 Restart the computer.
 This may be normal for Windows when it is processing

other CPU-intensive programs in the background or when the
system is accessing slow-speed devices such the floppy disk
drive.
 You may be running too many applications. Try to close
some applications or increase system memory for higher
performance.
 The processor may have been overheated due to the
system’s inability to regulate its internal heat. Make sure the
computer’s ventilation grills are not blocked.

Ŷ chapter 5 troubleshooting

5-16

Firewire (IEEE1394) and USB2.0 Problems

The USB device does not work -

 Windows NT 4.0 does not support USB protocols

 Check the settings in the Windows Control Panel.

 Make sure you have installed the necessary device

drivers.

 Contact the device vendor for additional support.

The IEEE1394 port does not work -

 Go to [Start > Settings > Control Panel > System >

Hardware > Device Manager]. You should see an entry which

reads “Texas Instrument OHCI Compliant IEEE 1394 Host

Controllers”. If it does not exist, Windows has not detected the

host controller or the device driver has not been installed

properly. If there is a yellow mark or red cross on the 1394 host

controller, it may be a device or resource conflict. Replace or

update the device driver from the factory CD-ROM disk or

consult the Windows manual on how to solve the resource

conflict problem.

 Make sure the cable is fully connected.

 Make sure you have installed the necessary device

drivers.

 Contact the device vendor for additional support.

Ŷ appendix A product specification

A

-1

APPENDIXź A

PRODUCT SPECIFICATION

Ŷ appendix A product specification

ź Processor and Core Logic

A

-2

 Mobile Intel Pentium M (Dothan), up to 2.13GHz,

2 MB L2 cache or

 Mobile Intel Celeron M, up to 1.60GHz, 1MB L2

cache
Intel Alviso 915PM + ICH6-M (FW82801FBM) chipset with
audio, modem, and USB2.0 controllers integrated
533 MHz (Pentium M) / 400 (Celeron M) Front Side Bus
400/533 MHz DDR2 interface

ź

System Memory

DDR2 SDRAM 400/533MHz, PC2700 compatible
128 / 256 / 512 / 1024MB, 2.5-Volt 64-bit bus
Two 200-pin DIMM sockets, Max 2 GB

ź

Display

 17-inch (1920x1200) WUXGA TFT display with

24-bit colors or

 17-inch (1440x900) WXGA+ TFT display with

24-bit colors

 nVidia NV42M (with 256MB frame buffer)
PCI Express bus architecture graphics capability
Hardware Motion Compensation and IDCT Supported for
MPEG1/2 Playback
DirectX compatible

(Integrated with graphic accelerator)

 Processor

 Core Logic

 Memory Type
 Default
 Memory

Expansion

 LCD Panel

 Graphic

Accelerator

 Graphic Bus
 Motion

Playback

 Other

Features

 S-Video

TV-out Encoder

Ŷ appendix A product specification

ź Audio

A

-3

Intel (ICH6M) integrated audio controller

Realtek ALC880

DirectSound 3D, EAX 1.0 & 2.0 compatible

A3D, I3DL2 compatible

AC97 V2.3 compatible

7.1 Multi-channel compatible (through S/PDIF)

Supports Azalia standard

2 Stereo Speakers with 1 Subwoofer

ź

Modem

Intel (ICH6M) integrated Modem Controller with MDC card,
Azalia standard support

ź

Wireless LAN

Intel PRO/Wireless 2200, MiniPCI Interface
IEEE802.11 B&G

ź

LAN / Ethernet

Realtek 8110 Ethernet function for

10/100/1000Base-TX network standards
Windows 2000 / XP Plug and Play compatible
Automatic Jam and auto-negotiation for flow control
Auto Negotiation and Parallel detection for automatic speed
selection (IEEE 802.3u)
High performance 32-bit PCI bus master architecture with
integrated DMA controller for low CPU and bus utilization
Remote Wake-up Scheme supported
Hot Insertion supported

 Chipset
 Audio Codec
 Sound

Capabilities

 Chipset

 Transmission

Rate

 Chipset

 PnP Function

 Flow Control
 Speed

Selection

 Other

Features

 Module
 Transmission

Protocol

Ŷ appendix A product specification

ź Firewire IEEE1394(a)

TI TSB43AB22A IEEE1394 OHCI Host Controller and
Up to 400 Mbps
Expandable up to 63 devices in chains

A

-4

ź

Storage

2.5-inch format hard disk drive

5.25-inch format (12.7mm height) fixed module

(Optional Purchase)

5.25-inch format (12.7mm height) fixed module

(Optional Purchase)

ź

Keyboard & Touch pad

88-key QWERTY keyboard with embedded numeric

keypad and Windows keys, 19.05mm Pitch

Built-in Touch Pad with Disable / Enable Touch Pad

button

ź

Express Card & Multiple Card Reader

(PC Card), (Card Reader)

Card TYPE II, Hot insertion and removal supported

Multimedia Card (MMC), Secure Digital Card (SD),

Memory Stick (MS), and MS Pro Card

 Hard Drive
 Combo Drive

 DVDrR/rRW

or DVD-Dual or
DVD-Multi
Standards

 Keyboard

 Touch pad

 Chipset

 Capabilities

 Chipset
 Express Card

 4-in-1 Card

Reader Format
Support

Ŷ appendix A product specification

ź Ports and Connectors

One Microphone-in jack
One Headphone / SPDIF jack
One Firewire (IEEE1394) host connector
Four USB2.0-compliant connectors
One standard network Ethernet connector (RJ-45)
One modem / phone connector (RJ11)
One S-video (TV-out) output connector
One DC-in connector
One DVI-I video connector
One 4-in-1 Card Reader slot
One PC Card Slot (type II)
One Consumer IR Lens/receiver
One VR Dial for audio/speaker volume

A

-5

ź

Battery Pack / AC Adapter

Li-ion 8-Cell pack, 14.8V x 4400 mAH

Low battery state with low battery warning beep
Uniwill SmartPower III Power Management

Smart Battery Compliant; low battery warning beep
Long Battery Life Mode and Silent Mode
Auto sensing AC-in 100~240V, DC-out 20V, 120W or 90W

 Mic-In Port
 Audio-Out / SPDIF
 Firewire
 USB2.0 Port
 Ethernet
 Modem
 S-Video
 Power-In
 DVI-I Port
 Card Reader
 PC Card Slot
 CIR Port
 VR Dial

 Primary

Battery Pack

 Feature

 Adapter

AC-Input /
DC-Output

Ŷ appendix A product specification

ź BIOS

AMI PnP BIOS
Power On Self Test
DRAM auto-detection, auto-sizing
L2 Cache auto-detection
Hard disk type auto-detection
APM 1.2 (Advanced Power Management) &
ACPI 2.0 (Advanced Configuration Power Interface)
Two Level Password Protections
32bit access, Ultra DMA, PIO5 Mode support
Multi-boot capability

Compatible with Microsoft Windows 2000 / XP / DOS

A

-6

ź

Physical Specification

408 (W) x 289 (D) x 25-38.1 (H) mm

8.8 lbs / 4 KG (with 17”LCD, DVD-ROM Drive, and 8-cell
battery pack)
Operating Temperature: 5 to 30

o

C (41 to 86oF)

Operating Humidity: 20 to 80 percent RH (5 to 35

o

C)

Storage Temperature: -15 to 50

o

C (-5 to 122oF)

 PnP Function
 Self Test
 Auto

Detection

 Power

Management

 Security
 Other

Features

 O/S

 Dimension
 Weigh t

 Environmental

Limits

Ŷ appendix B agency regulatory notices

B-1

APPENDIXź B

AGENCY REGULATORY NOTICES

Ŷ appendix B agency regulatory notices

B-2

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and the receiver.
 Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

 Consult the dealer or an experienced radio or television technician for

help.

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

"Alienware declare that M-5700 series (with wireless card: Intel
WM3B2200BG) is limited in CH1~CH11 by specified firmware controlled in
USA."

Ŷ appendix B agency regulatory notices

B-3

As long as conduction above is met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed (for Notebook).

IMPORTANT NOTE: In the event that these conditions can not be met

(for
example certain laptop configurations or co-location with another
transmitter), then the FCC authorization is no longer considered valid and
the FCC ID

can not

be used on the final product. In these circumstances,
the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

The final end product must be labeled in a visible area with the following:
“Contains TX FCC ID: PD9WM3B2200BG

Manual Information That Must be Included

The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module in the users manual of
the end product which integrate this module.

The users manual for OEM integrators must include the following information
in a prominent location “ IMPORTANT NOTE: To comply with FCC RF
exposure compliance requirements. The antenna must not be co-located or
operating in conjunction with any other antenna or transmitter.

Modifications

The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by the Manufacture may
void the user’s authority to operate the equipment.

Connections to Peripheral Devices

Connections to this device must be made with shielded cables with metallic
RFI/EMI connector hoods to maintain compliance with FCC Rules and
Regulations.

Declaration of Conformity

This device complies with Part 15( CLASS B

)/68 the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Ŷ appendix B agency regulatory notices

B-4

European Notice

Products with the CE Marking comply with both the EMC Directive
(89/336/EEC) and the Low Voltage Directive (73/23/EEC) and R&TTE
Directive (1999/5/EC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the following
European Norms:

 EN55022 : 1998+A1: 2000+A2: 2003, CLASS B
 EN61000-3-2 : 2000
 EN61000-3-3 : 1995+A1: 2001
 EN55024 : 1998+A1 : 2001+A1: 2003
 IEC61000-4-2: 2001
 IEC61000-4-3:2002+A1:2002
 IEC61000-4-4:1995+A1:2000+A2:2001
 IEC61000-4-5:2001
 IEC61000-4-6:2001
 IEC61000-4-8:2001
 IEC61000-4-11:2001
 EN50082 (IEC801-2, IEC801-3, IEC801-4) Electro-magnetic

Immunity

 EN 300 328-2, EN 300 328-1, EN 301 489-1, EN 301 489-17 (ETSI

300 328, ETSI 301 489) Electro-magnetic Compatibility and Radio
Spectrum Matter.

 TBR21 ( ETSI TBR21) Terminal Equipment.
 EN60950 (IEC950) I.T.E. Product Safety

Canadian Notice

This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the radio interference
regulations of the Canadian Department of Communications.

Le present appareil numerique nemet pas de bruits radioelectriques
depassant les limites applicables aux appareils numeriques de Classe B
prescrites dans le reglement sur le brouillage radioelectrique edicte par le
Ministere des Communications du Canada.

Power Cord Requirement

The power cord supplied with the AC adapter should match the plug and
voltage requirements for your local area. Regulatory approval for the AC
adapter has been obtained using the power cord for the local area. However,
if you travel to a different area and need to connect to a different outlet or
voltage, you should use one of the power cords listed below. To purchase a

Ŷ appendix B agency regulatory notices

B-5

power cord (including one for a country not listed below) or a replacement ac
adapter, contact your local dealer.

U.S. and Canada

 The cord set must be UL-Listed and CSA-Certified or C-UL Listed.
 The minimum specifications for the flexible cord are (1) No. 18 AWG,

(2) Type SJ, and (3) 3-conductor.

 The cord set must have a rated current capacity of at least 10 A.
 The attachment plug must be an earth-grounding type with a NEMA

5-15P (15A, 125V) or NEMA 6-15P (15 A, 250V) configuration.

Japan

 All components of the cord set (cord, connector, and plug) must bear

a `PSE` mark and registration number in accordance with the
Japanese Dentori Law.

 The minimum specification for the flexible cord are: (1) 0.75 mm

2

conductors, (2) Type VCT or VCTF, and (3) 3-conductor.

 The cord set must have minimum rated current capacity of 7 A.
 The attachment plug must be a two-pole, grounded type with a

Japanese Industrial Standard C8303 (15 A, 125 VAC) configuration.

Other Countries

 The cord set fittings must bear the certification mark of the agency

responsible for evaluation in a specific country. Acceptable agencies
are:

BSI (UK)
OVE (Australia)
CEBEC (Belgium)
SEMKO (Sweden)
FIMKO (Finland)
DEMKO (Denmark)
NEMKO (Norway)
SETI (Finland)
EANSW (Australia)
SEV (Switzerland)
IMQ (Italy)
UTE (France)
CCC (China)
PSB (Singapore)
PSE (Japan)
BSMI (Taiwan)
B (Polish)
VDE (Germany)

Ŷ appendix B agency regulatory notices

B-6

SASO (Saudi Arabia)

 The flexible cord must be of a HAR (harmonized) type HO5VV-F

3-conductor cord with a minimum conductor size of 0.03 square
inches.

 The minimum specification for the flexible cord for Class II product are:

(1) 2X0.75 mm

2

conductors, (2) 2-conductor cord.

 The cord set must have a current capacity of at least 10 A and a

nominal voltage rating of 125 / 250 VAC.

CAUTION: MODEL M-5700 series IS DESIGNED TO USE WITH THE
FLLOWING AC ADAPTER MODEL ONLY
Manufacture: LITE-ON ELECTRONICS, INC.; LI SHIN INTERNATIONAL
ENTERPRISE CORP.
Model:, PA-1121-22 (120W), 0227A20120 (120W)

Telephone lines requirement

 The appropriate utilization of 26AWG telephone line cord on unit.
CAUTION: Always disconnect all telephone lines from the wall outlet before
servicing or disassembling this equipment.
CAUTION: To reduce the risk of fire, use only No. 26AWG or larger
telecommunication line cord.

Battery Pack Safety

 The battery pack is intended to use only with this notebook.
 Do not disassemble the pack.
 Do not dispose of the battery pack in fire or water.
 To avoid risk of fire, burns, or damage to your battery pack, do not allow

a metal object to touch the battery contacts.

 Handle a damaged or leaking battery with extreme care. If you come in

contact with the electrolyte, wash the exposed area with soap and water.
If it contacts the eye, flush the eye with water for 15 minutes and seek
medical attention.

 Do not charge the battery pack if the ambient temperature exceeds 45

(113 ).

 To obtain a replacement battery, contact your local dealer.
 Do not expose the battery pack to high storage temperatures (above 60

, 140 ).

 When discarding a battery pack, contact your local waste disposal

provider regarding local restrictions on the disposal or recycling of
batteries.

 Use only supplied AC Adapter for charging.

Ŷ appendix B agency regulatory notices

B-7

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions or local
laws.

VORSICHT! Explisionsgefahr bei unsachgernazen Austausch der Batterie.
Ersatz nur durch denselben oder einem vom Hersteller empfohlenem
ahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des
Herstellers.

Laser Safety

The optical drive used with this computer is certified as a Class 1 laser device
according to the U.S. Department of Health and Human Services (DHHS)
Radiation Performance Standard and International Standards IEC 825 / IEC
825-1 (EN60825 / EN60825-1). The device is not considered harmful, but the
following precautions are recommended:

 Do not open the unit.
 Avoid direct exposure to the laser beam.
 If the unit requires service, contact an authorized service center.
 Ensure proper use by reading and following the instructions carefully.
 Do not attempt to make any adjustment of the unit.

CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASSE 1
LASERSCHUTZKLASSE 1 PRODUKT

Warning!

Do not attempt to disassemble the cabinet containing the laser. The laser
beam used in this product is harmful to the eyes. The use of optical
instruments, such as magnifying lenses, with this product increase the
potential hazard to your eyes. For your safety, have this equipment serviced
only by an authorized service provider.

Lithium battery warning / Bridge battery warning

This computer contains a lithium battery to power the clock and calendar
circuitry.

Ŷ appendix B agency regulatory notices

CAUTION: Danger of explosion if battery is replaced incorrectly. Replace only
with the same or equivalent type recommended by the manufacturer. Discard
used batteries according to the manufacturer’s instructions.

ATTENTION: Il y a danger d’xplosion s’il y a remplacement incorrect de la
batterie. Remplacer uniquement avcc unc batterie du meme type ou d’un
type recommande par le constructer. Mettre au rebut les batteries usagees
conformement aux instructions du fabricant.

VORSICHT! Explosionsgefahr bei unsachgemBen Austausch der Batterie
Ersatz nur durch denselben oder einem vom Hersteller empfohlenem
ahnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des
Herstellers.

Der Arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 betragt 70dB
(A) oder weniger.

Zum Netzanschlua dieses Gerates ist eine geprufte Leitung zu verwenden.
Fur einen Nennstrom bis 6A und einem Gerategewicht groBer 3kg ist eine
Leitung nicht leichter als (1)H05VV-F, 3G, 0.75mm

2

(2)2X0.75 mm

2

conductors

einzusetzen.

Die Steckdose muB nahe dem Gerat angebracht und leicht zuganglich
sein.

CAUTION!
T his pa rt is h ot. B e C arefu l.
VORSICHT!
Di ese Flache wird sehr heiss.

When you see this symbol, be careful as this spot may be very hot.

B-8

Ŷ CyberLink Power Cinema Guide

APPENDIXź C

CyberLink Power Cinema Guide

Ŷ CyberLink Power Cinema Guide

Copyright and Disclaimer

All rights reserved. No part of this publication may be reproduced,

stored in a retrieval system, or transmitted in any form or by any

means electronic, mechanical, photocopying, recording, or

otherwise without the prior written permission of CyberLink

Corporation.

To the extent allowed by law, POWERCINEMA IS PROVIDED

“AS IS”, WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESS OR IMPLIED, INCLUDING WITHOUT

LIMITATION ANY WARRANTY FOR INFORMATION,

SERVICES, OR PRODUCTS PROVIDED THROUGH OR IN

CONNECTION WITH POWERCINEMA AND ANY IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE, EXPECTATION OF PRIVACY, OR

NONINFRINGEMENT.

BY USING THIS SOFTWARE, YOU AGREE THAT

CYBERLINK WILL NOT BE LIABLE FOR ANY DIRECT,

INDIRECT, OR CONSEQUENTIAL LOSS ARISING FROM

THE USE OF THIS SOFTWARE OR MATERIALS

CONTAINED EITHER IN THIS PACKAGE.

The terms and conditions here under shall be governed and

construed in accordance with the laws of Taiwan.

Ŷ CyberLink Power Cinema Guide

PowerCinema is a registered trademark along with other company

and product names mentioned in this publication, used for

identification purposes and remain the exclusive property of their

respective owners.

Ŷ CyberLink Power Cinema Guide

International

Headquarters

Mailing Address

CyberLink Corporation

15F, #100, Min Chuan Road, Hsin Tian City

Taipei County, Taiwan, R.O.C.

Web Site

www.gocyberlink.com

Phone Numbers

Telephone: [phone]

Fax: [phone]

Copyright © 1999-2005 CyberLink Corporation