Cutler Hammer, Div of Eaton Corp Molded-Case Circuit Breakers Catalog Page
Molded-Case Circuit Breakers
Replacement Capabilities
3
Accessories
Spacer kit to Vari-Width
(not for use with fixed
mechanisms) catalog
number AMTSK1 for up
to 1.00-inch variation.
Note: This spacer kit is for up to
1.00-inch variation and consists of
multiples of thin spacers to be
used as required. A maximum
of two kits per installation may
be used. Due to the possible
variation in dimensions, hardware
is not supplied. Use standard
1/4–20 bolts.
Ordering Information
●
Complete assembly
not available, order
components parts as listed
on Pages V12-T3-104,
V12-T3-105 and
V12-T3-106
●
Order spacer kits or
door hardware adapter
as required
●
Individual component
parts may be ordered by
catalog number
Flex Shaft
Flex Shaft
The Flex Shaft is an extra
heavy-duty mechanism that
includes a flexible shaft in
various lengths, 3 feet (0.9m)
Flex Shaft Ordering Information (Three-Pole Only)
Flexible Shaft Length in Feet (m)
Breaker
Frame
E125 EHMFS03 EHMFS04 EHMFS05 EHMFS06 — — — —
J250 JHMFS03 JHMFS04 JHMFS05 JHMFS06 JHMFS07 JHMFS08 JHMFS09 JHMFS10
G F0S03C F0S04C F0S05C F0S06C — — — —
F F1S03C F1S04C F1S05C F1S06C F1S07C F1S08C F1S09C F1S10C
F (Dual) F1S03CD F1S04CD F1S05CD F1S06CD F1S07CD F1S08CD F1S09CD F1S10CD
J F2S03C F2S04C F2S05C F2S06C F2S07C F2S08C F2S09C F2S10C
K F3S03C F3S04C F3S05C F3S06C F3S07C F3S08C F3S09C F3S10C
L and MDL — F4S04C F4S05C F4S06C — — — F4S10C
N — F5S04C F5S05C F5S06C — — — F5S10C
R — F6S04 F6S05 F6S06 — — — —
MD — F7S04C F7S05C F7S06C — — — F7S10C
Flex Shaft Accessories
(F- through R-Frame)
NEMA 12 Safety Door
Hardware for Flex Shaft
Handle Length
in Inches (mm)
4.00 (101.6) C361KJ4
6.00 (152.4) C361KJ6
Roller latch
3.00 (0.9) 4.00 (1.2) 5.00 (1.5) 6.00 (1.8) 7.00 (2.1) 8.00 (2.4) 9.00 (2.7) 10.00 (3.0)
Catalog Number
4
Catalog
5
Number
6
C361KR
through 10 feet (3m) for use
with various size enclosures.
The Flex Shaft handle will
accept up to three padlock
shackles, each with a
maximum diameter of
0.375-inch (9.5 mm). Can be
used with Type 1, 3R and 12
fabricated enclosures. An
optional handle is available
for Flex Shaft that is suitable
for use with Type 4 and 4X
environments. Flex Shaft
comes preset from the
factory, requiring only
minor field adjustments
on installation, which
takes about 10 minutes—
123
Notes
1
Type 4/4X handle mechanisms are
available. Add Suffix
catalog number. Add Suffix
catalog number for IEC handle. Add
L (Standard on F, J, K and L) to
Suffix
complete catalog number for 6.00-inch
(152.4 mm) handle. Original narrow
handle design (no
C from catalog number.
Remove
2
When selecting the length of shaft,
ensure minimum bending radius of
4.00 inches (101.6 mm) is maintained to
operate properly. The standard method
of shipment includes the mechanism
preset at the factory; however, minor
field adjustments may be required.
X to complete
I to complete
C suffix) is available.
a significant time savings
compared to installation of
other types of flange handle
mechanisms. The Flex Shaft
mechanism also takes up less
interior enclosure space than
competitive designs and the
handle fits standard flange
cutouts. Flex Shaft handle
can be remotely mounted
from breaker, where an
operator can use it by
“funneling” the cable
through conduit.
Flex Shaft is UL Listed under
File E64983 and meets
CSA requirements.
3
Dual breakers operator available
on F-Frame only.
4
Customer: Consult with box
manufacturer for correct door hardware
and any adapters required for assembly.
5
The 0.25 inch x 0.50 inch (6.35 x 12.7 mm)
standard mill rectangular locking bar is
not supplied with these kits.
6
Third roller latch for use with 4.00- or
6.00-inch (101.6 or 152.4 mm) handle
when 3-point latching is required.
Refer to handle mechanisms in the moldedcase circuit breaker section of Volume 4—
Circuit Protection Catalog, CA08100005E,
Tab 2.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Volume 12—Aftermarket, Renewal Parts and Life Extension Solutions CA08100014E—October 2016 V12-T3-107
22
23
24
25
Loading...