Curtis WF-037a User Manual

Scouting Camera
User’s Manual
Model: WF-037a
Open view image with major parts indication
Bottom view
Attention.
The software CD-ROM packaged with the camera is designed for PC’s only. Playing this CD-ROM on a stereo or CD player may cause damage to it.
This camera is a precision electronic device. Do not attempt to service this camera yourself, as opening or removing covers may expose you to dangerous voltage points or other risks.
Please use the lens cloth to clear the lens and do not touch the lens with fingers.
Getting to know your Scouting Camera
1. Package contents.
Please check if the following items are in the package when purchasing this product.
CDROM (Contented with Ulead PE 8 and driver)
User Manual.
1.5M USB cable.
1.5M TV out cable for TV (RCA Jack).
Strap.
Installation.
1. Preparation.
CDROM – Contains Scouting Camera driver and application program.
USB cable – Comes with product.
TV out cable – Comes with product.
Battery – 6 Alkaline batteri es, size C
2. Software installation.
Unplug the USB cable from PC.
Insert the CDROM in CD driver of your PC.
The auto-run program will execute.
Follow the instructions shown on screen from your
PC to completely install the driver and application program.
Restart windows.
Successful installation will create “Ulead Photo
Explorer” icon on you desktop.
Power off the unit.
Connect your camera to the PC by the USB cable,
the PC will recognize the new device and set UP the configuration of the PC automatically.
A new disk will be found under My Computer.
¾ If your computer dosen’t run automatically, please
click “Start” button and choose “Run”, and then browse the CD drive and click “Setup”.
¾ Operation manual of Ulead Photo Explorer is
contained on the provided CDROM.
3. Battery and SD memory card installation.
Open the front cover.
Slide the power switch to OFF.
Open the battery door.
Put the battery with correct directions.
Close the battery door .
¾ Alkaline batteries should be used and please make
sure the batteries polarity is correct.
An image to shown how to locate the battery
Push the SD memory card in to the SD card slot till the end and in the correct direction as shown.
To remove the SD memory card by press the SD card to the end, the SD memory will eject from the SD card slot.
Slide the power switch to on.

An image to show how to locate the SD card

4. Memory Options.
You Scouting camera is comes 16MB built in flash memory, the camera is also equipped with an expendable media card slot capable accepting up to 512M SD memory card (sold separately), With no memory card inserted into the slot, the camera will use the built in 16MB memory, If a SD memory card is inserted into the slot then the camera will bypass the built in memory and utilize the compact flash memory. The front counter display will show the number of images on the built in memory unless the expansion card is inserted at which point the counter will only show the number of images o the expansion card.
¾ The camera should be in the OFF position when
adding or removing the memory cards.
¾ SD memory cards must be clean (not images from
other sources), if you are using the SD memory card from other cameras, please make sure the format
the SD card prior use in Scouting Camera. New cards are good to use straight from the package.
Display, Controls and Programming.
1. Status Icons on TFT display.
Time out: To set the time amount of time the camera will sleep between PIR triggering.
Auto Flash: If the brightness is lower then EV 12. the unit will turn on the flash lighting automatically.
Capture mode: It shown the capture mode that you have selected.
o 1P: Single image capturing per PIR triggering. o 2P: Two images continuous capturing per PIR
triggering.
o 3P: Three images continuous capturing per PIR
triggering.
o Video: Taking 10 seconds video per PIR
triggering.
Resolution: It shown the resolution selection that you have selected. o 1600 x 1200 2.0M: Select this option to capture
Loading...
+ 25 hidden pages