Curtis PL4210A-2 User Manual

Contents

 Introduction

 Warning

 Caution

 Main Unit Description

 Remote Control

 OSD basic adjustment

 Specification

 Trouble Shooting

Introduction

Thank you very much for your purchase of

normal color TV and PC monitor. To enjoy your

read this manual carefully and keep it handy for ready reference.

INSTALLATION

Locate the TV in a room where direct light does not strike the screen. Total darkness or

a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is

recommended for comfortable viewing.

Allow enough space between the receiver and the wall to permit ventilation.

Avoid excessively warm locations to prevent possible damage to the cabinet or

premature component failure.

This TV can be connected to AC100-240V~ 50/60HZ.

Do not install the TV in a location near heat sources such as radiator, air ducts, direct

our product of PDP TV. It serves as a

TV to the full from the very beginning,

sunlight, or in a place somewhere like close compartment and close area. Do not cover

the ventilation openings when using the TV.

The indicator light will last about 30 seconds to go out after cutting off the electricity,

during this period, you cannot repower it on until the indicator light goes out, thanks a

lot for your attention!

Warning

RISK OF ELECTRIC SHOCK

CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER- SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended t

of electric shock, do not disassemble this equipment by

anyone except a qualified service personnel.

CAUTION

DO NOT OPEN

o alert the user to avoid the risk

This symbol is intended to alert the user to the presence

of important operation and maintenance instructions in

the literature accompanying the equipment.

Caution

High voltages are used in the operation of this product.

- Do not

open the product's casing. Refer servicing

to qualified service personnel .

Caution

To prevent fire or electrical shock hazard, Do not expose

the main unit to moisture.

Caution

Do not drop or push objects into the television cabinet

slots or openings. Never spill any kind of liquid on the

television receiver.

Caution

Avoid exposing the main unit to direct sunlight and other

directly on other products which give off heat. E. g. video

cassette players, Audio amplifiers. Do not block the

ventilation holes in the back cover. Ventilation is essential

to prevent failure of electrical component. Do not squash

power supply cord under the main

sources of heat. Do not stand the television receiver

unit or other heavy objects.

Caution

Never stand on, lean on, push suddenly the product

or its stand. You should Pay special attention to

children.

Caution

Do not place the main unit on an unstable cart stand,

shelf or table. Serious injury to an individual, and

damage to the television, may result if it should fall.

Caution

When the product is not used for an extended period

of time, it is advisable to disconnect the AC power

cord from the AC outlet.

Caution

The PDP panel used in this product is made of glass.

Therefore, it can break when the product is dropped

or applied with impact. Be careful not to be injured

by broken glass pieces in case the PDP panel breaks.

Main unit description

Control Panel Button Function

VOL+ : Volume up. VOL- : Volume down. CH+: TV channel up. CH- : TV channel down. MENU : Press to select the main menu. TV/AV : Select the input signal.

POWER : Switch on when in

standby mode or enter the standby mode.

TV Terminal Connections

1. HDMI1 input terminal.

2. HDMI2 input terminal.

3. HDMI3 input terminal.

4. VGA input terminal.

5. PC audio input terminal.

6. VIDEO2 input terminal.

7. AUDIO2 input terminal.

8. Component input terminal.

9. VIDEO1 input terminal.

10. AUDIO1 input terminal.

11. TV antenna

12. USB input terminal˄RQO\IRUXSJUDGHVRIW˅

Power Input Configuration



AC POWER

Locations of wall mout, power and terminals

NOTE

●The TV dose not support wake sleep

● It supports must more than 2 GB It supports FAT/FAT32 document. The max FAT

document is 4GB and the max FAT32 document is 2TB.

Remote control

POWER: Power on/off button, press once to turn the TV on and

press again to turn the TV off.

MUTE: Press this button FREEZE˖Press this key to hold the picture

SLEEP: Set the sleep timer.

ASPECT: Press to

Enter electronic program guide

EPG˖

CC: Press this key to select the CC Mode. Three CC Mode are

available including On, CC on mute and off

AUTO: Adjust the picture automatically in pc mode.

PMODE: Select picture mode.

SMODE: Select sound mode.

MTS/AUDIO: When stereo program is received, press this key to

switch sound system between mono and stereo.

When SAP program is received, press this button to switch

sound system between mono and SAP

When stereo and SAP program is received, press this key to

switch among mono, stereo and SAP.

Press this key to show the list of audio languages available for

the current channel in ATSC

SOURCE: Press to change signal source.

MENU: Press this button to enter the main menu.

EXIT: Exit the OSD (On-screen display).

ENTER: Enter the selected option or perform the selected

operation.

0-9: Select and switch to a channel using 0 - 9.

Switch the program digit.

-/--:

: Switch back and front between the current and previous channels.

CH+/CH-: Change the channel.

VOL+/VOL-: Adjust the volume.

INFO: Display some information of current program in TV mode.

FAV: Switch between custom set " Favorite List"

F.LIST: Switch between custom set "Favorite List"

C.LIST: Press this key to display the channel list in TV mode

to mute or restore sound.

adjust picture ratio.

OSD basic adjustment

Installation Guide

Press MENU button to display the MAIN OSD MENU;

. Press ◄ / ►button to select the MENU you want;Press ENTER button to enter the sub menu;

. Press ▼ / ▲ button to select the option and then press ◄ / ► to adjust the value in the sub

menu;

. You can press MENU button to go back to the upper menu or EXIT button to close the OSD.

PICTURE

Press ENTER when the Picture Settings item is highlighted. Then you will go to the

sub-menu as following.

Press ▼ / ▲ to select the desired menu item. Press ENTER to proceed if necessary.

◄ / ► to to adjust the item the desired level.

Press

When you have changed the settings, you can exit from the menu by pressing MENU.

Picture Settings

Press ▼ / ▲ button to select Picture Settings, then press ◄ / ► button to adjust. Only in

the User mode, the detail options as following can be adjusted.

. Press ▼ / ▲ button to select Brightness,then press ◄ / ► button to adjust.

. Press ▼ / ▲ button to select Contrast,then press ◄ / ► button to adjust.

. Press ▼ / ▲ button to select Colort,then press ◄ / ► button to adjust.

. Press ▼ / ▲ button to select Sharpness,then press ◄ / ► button to adjust.

. Press ▼ / ▲ button to select Tint,then press ◄ / ► button to adjust.

Screen Settings

.Press ENTER when the Screen Settings item is highlighted. Then you will go to the

sub-menu as following.

.Press to select the desired menu item. Press ENTER to ▼ / ▲ proceed if necessary.

.Press ◄ / ► to adjust the item to the desired level.

.When you have changed the settings, you can exit from the menu by pressing MENU.

Screen Size

Press ▼ / ▲ button to select Screen Size, then press ◄ / ► button to adjust.

Auto Wide

Press ▼ / ▲ button to select the item Auto Wide, then press ENTER button to adjust. It

can set the picture to fit the screen automatically. When the Auto Wide is selected, the

symbol will show as following:

PC Settings

Note : The pc settings only in pc mode

.Press ENTER when the PC Settings item is highlighted. Then you will go the sub-menu as

following.

.Press to select the desired menu item. Press ENTER to ▼ / ▲ proceed if necessary.

.Press ◄ / ► to adjust the item to the desired level.

.When you have changed the settings, you can exit from the menu by pressing MENU.

Press ▼ / ▲ button to select Auto Adjust, then press ENTER button to start auto

adjusting.

Press ▼ / ▲ button to select Horizontal Position,then press ◄ / ► button to adjust.

Press ▼ / ▲ button to select Vertical Position, then press ◄ / ► button to adjust.

Press ▼ / ▲ button to select Clock, then press ◄ / ► button to adjust.

Press ▼ / ▲ button to select Phase, then press ◄ / ► button to adjust.

Press ▼ / ▲ button to select Reset, then press ENTER button to reset the options above.

Color Temperatur

Press ENTER when the Color Temperature item is highlighted. Then press ◄ / ► button

to adjust.

Advanced Picture Settings

Dynamic Contrast

Press ▼ / ▲ button to select the item Dynamic Contrast, then press ◄ / ► button to

adjust. it can adjust the contrast

Film Mode

Press ▼ / ▲ button to select the item Film Mode, then press ◄ / ► button to adjust.

Noise Reduction

Press ▼ / ▲ button to select the item Noise Reduction, then press ◄ / ► button to adjust.

MPEG Noise Reduction

Press ▼ / ▲ button to select the item MPEG Noise Reduction, then press ◄ / ► button to

adjust. It can improve the quality of the pictures by reducing the block noise.

SOUND

Sound Settings

Press ENTER when the Sound Settings item is highlighted. Then you will go to the

sub-menu as following.

Press ▼ / ▲ to select the desired menu item. Press ENTER to proceed if necessary.

Press e/f to to adjust the item the desired level.

When you have changed the settings, you can exit from the menu by pressing MENU.

Bass

Press ▼ / ▲ button to select the item Bass,then press ◄ / ► button to adjust.

Treble

Press ▼ / ▲ button to select the item Treble,then press ◄ / ► button to adjust.

Balance

Press ▼ / ▲ button to select the item Balance,then press ◄ / ► button to adjust.

Surround Mode

Press ▼ / ▲ button to select the item Surround Mode, then press ENTER button to adjust.

Analog Sound

Press ▼ / ▲ button to select the item Preferred Analog Sound, then press ◄ / ► button to

select the prefer audio

Digital Sound

Press ▼ / ▲ button to select the item Preferred Digital Sound, then press ◄ / ► button to

select the prefer audio

Other Settings

AVL

Press ▼ / ▲ button to select the item AVL, then press ◄ / ► button to select ON or OFF.

Auto Volume Level

Speaker

Press ▼ / ▲ button to select the item Speaker, then press ◄ / ► button to select ON or

OFF. If set it Off, the speaker will be mute.

Equalizer Mode

Press ▼ / ▲ button to select the item Equalizer Mode, then press ◄ / ► button

desired mode.

CHANNEL MENU

Note: This menu is only shown when the input source is TV .

Channel List

Press ▼ / ▲ button to select Channel List , then press enter scan the Channel List.

If you select the press enter button to option “In Channel List” On, the channel label

will display in the list

Favorite List

Press ▼ / ▲ button to select Favorite List , then press ENTER button to scan the Favorite

Channel List.

Channel Setting

Press ▼ / ▲ button to select Manual Channel Setting , then press ENTER button to set

the value in the sub menu.

Channel Number

Press ▼ / ▲ button to select Channel Number , then press ◄ / ► button to select the

Channel Number.

In Channel List

Press ▼ / ▲ button to select In Channel List, then press ENTER button to Add or Delete

the current channel in the channel list.

&KDQQHO/DEHO

Press ▼ / ▲ button to select Channel Label, then press◄ / ► button to set the channel

lable., and press ENTER button to edit next lable.

Favorite Channel

Press ▼ / ▲ button to select Favorite Channel, then press ENTER button to Add or Delete

the current channel in Favorite Channel list.

Signal Type

Press ▼ / ▲ button to select Signal Type, then press button e/f” to select the type

you want to set.There are two selections: Air and Cable.

Auto Channel Search

Press ▼ / ▲ button to select Auto Channel Search, then press ENTER button to search

channel. A Channel Search Menu will appear as below.IF you stop search ,press menu

key.

PARENTAL CONTROL

Input password to enter, default password is “0000”.

V-CHIP

Press ▼ / ▲ button to select V-CHIP, then press ENTER button to adjust. A Sub Menu

Will appear as below.

+ 44 hidden pages