CURTIS MWC529 User Manual
WATER COOLER
INSTRUCTION MANUAL
MODEL: MWC529
ELECTRICAL SAFETY
When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire,
electric shock, and injury to person or property. Read all instructions before using any appliance.
- Do not let hot water touch bare skin. Keep combustible materials such as furniture, bedding, pillows, clothes, and/or paper away from the back of the unit.
- Do not operate this, or any other appliance with a damaged cord. No other appliance should be plugged
into the same outlet. Be sure that the plug is fully inserted into receptacle.
- Do not run cord over carpeting or other heat . Do not cover the cord. Keep cord away from traffic radiator
areas, and do not submerge in water.
- We do not recommend the use of an extension cord as it may overheat and cause a risk of fire. If you
must use an extension cord, use no. 14 AWG minimum size and rated not less than 1875 watts.
- Unplug the water dispenser before cleaning or making repairs.
- Do not plug your water dispenser into the power outlet or turn the power switches on, when the water
dispenser is empty.
- Exercise caution and use reasonnable supervision when appliance is used by or near children.
- Do not use your water dispenser outdoors. Place the water dispenser away from direct sunlight and make
sure that there is at least 4 inches of space between the back of you unit and the wall.
Keep a miminum distance of 2 inches on each side of your unit free.
UNPACKING YOUR WATER DISPENSER
1- Remove the water dispenser from the cardboard box with
out turning it upside down, or laying it on its side.
a- Remove the strapping.
b- Open the box.
4- Remove the styrofoam packing inserts from the box.
d- Pull the water dispenser straight up from the box.
e- Remove the plastic bag.
The refrigeration compressor has very sensitive mounts inside
of its welded shell in order to provide quiet running. Improper
handling may damage the compressor.
2- Wipe it clean if necessary.
3- Find a location for your cater dispenser that is protected from direct sunlight and other sources of heat.
Place the water dispenser on a level surface. Make sure that there is at least 4 inches of space between
the back of you water dispenser and the wall. Keep a minimum distance of 2 inches on each side of you
water dispenser free;
4- Do not plug your water dispenser into the power outlet yet ! Read the instructions first.
This water dispenser is for indoor use only
Room temperature shuld no exceed 97°F / 36° C.
1
GETTING TO KNOW YOUR WATER DISPENSER
Cooling tank for the cold water, made of stainless steel.
For the hot water there is a stainless steel heavy duty hot water tanks with
an external heater. It is suitable for mineral water.
Thermostat on the rear panel.
Two switches on the rear panel : one for the hot water, one for the cold water.
All water ways are made from stainless steel
Refrigeration compressor is quiet and durable.
The power cord has a grounded plug. Please make sure that your outlet
is properly grounded.
Integrated No-Spill system for added hygiene and convenience.
There are two high-flow taps on the front. The tap handles are color-coded.
Red is for hot, blue for cold water.
The hot water tap handle has a child resistant hot water guard. To operate it, squeeze
the handle and locking device together and then push them down
Easy to clean deep drip tray
PREPARING YOU WATER DISPENSER
1- Make sure that the water dispenser is not plugged into the electrical outlet.
2- Hold the water bottle vertically and upside down and place the water bottle
into the no-spill bottle receptacle. Apply slight pressure in order to pierce the
bottle cap with the spigot. It is no advisable to make any adjustments to the
thermostat setting before the water dispenser and bottled water are warmed
up to normal room temperature. This unit accepts two, three or five gallon
water bottles.
3- Open the two taps to let air out , until the water starts to flow. When
this happens, release the buttons.
4- Plug the water dispenser into a grounded power outlet and turn the
power switches on.
5- If the water dispenser is brought in from outside in the winter time, give it
few hours to warm up to room temperature before plugging it in. The
thermostat setting may be affected by coldness of the water dispenser itself
or the bottled water.
- The refrigeration thermostat is factory set between 7°C and 8°C (44.6°F and 46.4° F).
- The hot water thermostat is factory set between 88°C adn 89°C (190.4°F and 192.1°F).
- Before the water dispenser leaves the factory, the thermostat is set properly. It is not advisable to adjust
the thermostat when using the water dispenser.
▌
▼
PLACE
BOTTLE
VERTICALLY
STRAIGHT
NOTE :
When your water dispense is in operation there is a small amount of water in the water passage between
the water tanks and the taps.This water is not controlled by the cold or hot temperature settings. We recommend that in order to fully enjoy the desired water setting, you should eliminate this small amount, 200ml
- 400ml (6.76 fl .oz-13.52 fl .oz) using a small glass container.
2
Loading...