Culligan 7850W, 7850, 7850S User Manual

INS115D

OWNER’S MANUAL

Model Numbers 7850, 7850S, 7850W

U.S. Patent Des. 385,338 Other Foreign and Domestic Patents Pending

INS115D

HELPLINE: 1-800-BUY-MOEN

PRODUCT FEATURES

Newly styled handle and spout receptor

Electronic

filter life indicator

Filtered

water

button

Filtered

water outlet

Stream & Spray

Actuating Buttons

Packed with deck plate or single hole deck ring

Easy to replace water filter integrated in pullout spout

➤

INS115D

HELPLINE: 1-800-BUY-MOEN

WELCOME TO MOEN

Congratulations! You’ve purchased the revolutionary PureTouch

Filtering Faucet System. This faucet is the first of its kind and is designed to provide great tasting, cleaner water with just one touch. To get the most enjoyment from your Moen PureTouch Filtering System, please read all installation and operating instructions carefully. With simple care and maintenance, the PureTouch Filtering Faucet System will provide many years of reliable performance. If you should have any questions, please call us toll-free at 1-800-BUY-MOEN.

TABLE OF CONTENTS

Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Water Filtration Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Parts Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Battery and Upper Housing Replacement . . . . . . . . . . . . . . .11

Filter Replacement Instructions . . . . . . . . . . . . . . . . . . . . . . . .13

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

WATER FILTRATION SAFEGUARDS

Your Moen PureTouch®Filtering Faucet System integrates carbon block filtration technology designed by Culligan International into a faucet spout. This technology is fast and effective at reducing or removing contaminants commonly found in water and is certified by NSF. The PureTouch Filtering Faucet System and installation must comply with State and Local laws and regulations. To ensure optimal operation of your new Moen faucet, please read the following safeguards carefully.

MicroTech™ Filter Cartridges

•MicroTech filter cartridges will reduce : Chlorine, Taste and Odor (MicroTech 5000, 3000, 1000) Lead (MicroTech 5000, 3000) Cysts (Cryptosporidium, Giardia)(MicroTech 5000)*

* The contaminants removed or reduced by this filter are not necessarily in your water.

• Do not use with water that is microbiologically unsafe or of unknown

quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

•MicroTech filter cartridges are designed for replacement after

dispensing 200 gallons of filtered water (approximately 3 months). Water conditions and usage may affect filter life.

• The electronic indicator will signal when filter replacement is

necessary (see page 13).

• Use only MicroTech filter cartridges with the PureTouch Filtering

Faucet System.

• Filter flow rate = .4-.5 gpm at rated pressure (20psi minimum - 125psi

maximum).

Water Temperature

• Minimum/Maximum faucet operating temperature = 40° - 150°F.

• CAUTION: Do not filter water above 100° F.

MicroTech Filter Flushing Instructions

• New MicroTech Filter Cartridge: Allow cold water to run through a

new filter for 5 minutes to flush out any loose carbon particles. Once these small black specks are washed out the filter is ready for use.

• Daily Use: Allow cold water to run through the filter for 10-15 seconds

prior to first use. If the filter has not been used for two days, run cold water through the filter for 60 seconds prior to the first use.

Questions

• If you have any questions please call our toll-free helpline,

1-800-BUY-MOEN. Monday through Friday 8:00 a.m. to 8:00 p.m.,

Saturday 8:00 a.m. to 6:30 p.m.

HELPLINE: 1-800-BUY-MOEN

INS115D

HELPLINE: 1-800-BUY-MOEN

PAR TS DESCRIPTION• DESCRIPTION DES PIÈCES • DESCRIPTIÓN DE PIEZAS



ENGLISH

FRANÇAIS

ESPAÑOL

Solid Handle Body

Corps de poignée solide

Cuerpo de Manija Sólido

Set Screw

Vis de blocage

Tornillo Opresor

Plug Button

Bouton de bouchage

Batón Tapón

Dome

Dôme

Cúpula

Cartridge Screw

Vis de cartouche

Tornillo del Cartucho

Handle Adapter

Adaptateur de poignée

Adaptador del Monomando

Handle Connector

Raccord de poignée

Conector del Monomando

Pivot Retainer

Bague de retenue de pivot

Retenedor de Pivote

Wave Spring Washer

Rondelle élastique ondulée

Arandela de Resorte en Onda

Pivot Stop

Arrêt de pivot

Parada Pivote

Retainer Nut

Écrou de retenue

Tuerca Retenedora

Bearing Washer

Rondelle de roulement

Arandela de Présion

Retainer Clip

Bride

Presilla Retenedora

1225 Cartridge

Cartouche 1225

Cartucho 1225

Spout Receptor

Récepteur de bec

Receptor del surtidor

Hose Connection

Raccord de tuyau

Conexión de Manguera

Screen Washer

Rondelle filtre

Arandela de Malla

Quarter Turn Connector

Raccord de quart de tour

Conector de un Cuarto de Vuelta

Pull-out Spout

Bec rétractable

Surtidor portátil

Upper Housing Unit

Boîtier supérieur

Unidad del cárter superior

Filter Outlet Nut

Écrou de sortie de filtre

Tuerca de la Salida del Filtro

Aerator

Aérateur

Aireador

Filter Cover

Couvercle de filtre

Cubierta del Filtro

Threaded Discharge Tube

Tuyau de décharge fileté

Tubo de descarga Roscado

Supply Tubes (2)

Tuyau d’alimentation (2)

Tubos de Alimentación

Deck Plate

Plaque de comptoir

Placa de Cubierta

Deck Ring

Anneau de comptoir

Anillo de Cubierta

Ring Gasket

Joint annulaire plat

Empaque

1/2" Threaded Fitting (2)

Raccord fileté de 1/2 po (2)

Montaje Roscado de 13mm (2)

Support Plate

with gasket

Plaque de soutien avec bague

d'etanchéité

Placa de Soporte

con Empaque

Mounting Bracket

Support de fixation

Soporte de Montaje

Medium Mounting Nut

Écrou moyen de montage

Tuerca de Montaje Mediana

Spout Hose

Tuyau de bec

Manguera del surtidor

Counter Weight

Contrepoids

Contrapso

Mounting Tool

Outil de montage

Herramienta de Montaje

Filter (not shown)

Filtre (non illustré)

Filtro (no se muestra)

Large Mounting Nut (2)

(not shown)

Gros écrou de montage (2)

(non illustré)

Tuerca de Montaje Grande (2)

(no se muestra)

Washer

Rondelle

Arandela

Wand Appliance

Dispositivo del rociador

Appareil de filtration

HELPLINE: 1-800-BUY-MOEN

INSTALLATION INSTRUCTIONS

CAUTION: Always turn water supplies OFF before removing existing faucet. Turn

faucet on to relieve water pressure and to ensure water is completely off.

OLD FAUCET REMOVAL: Your old faucet may attach in a number of different ways depending on the brand. To remove, reverse steps in installation instruction sheet of old faucet, follow instructions in a DIY type of book or follow instructions listed below.

After years of use, you may need to use a penetrating oil spray on the faucet mounting hardware to help loosen corrosion and assist in removing the faucet connections.

Disconnect water supply lines from faucet supply lines. Remove mounting hardware using a basin wrench or channel lock pliers. Lift out faucet. Thoroughly clean and dry the mounting surface after removal of old faucet.

INSTALLING PURETOUCH® FILTERING FAUCET SYSTEM

Helpful Tools: Phillips screwdriver, adjustable wrench (2)

CAUTION: Do not use with portable washing devices, i.e. dishwashers, washing machines.

NOTE: Do not bend supply tubes until instructed in step 5.

1. Place screen washer (17) in hose connection (16) and attach to pull-out spout (19). A few threads on the quarter turn connector (18) will be showing.

2. With the spout receptor (15) facing directly forward and threaded discharge tube (24) in back, feed small end of hose (34) down through spout receptor. When encountering resistance, feed the hose through with a push/pull motion. Set aside faucet assembly.

Depending on your sink configuration, you have the option to install your faucet with a deck plate (27) or a round deck ring (28). NOTE: Never use deck plate

(27) and deck ring (28) together on one sink.

3a.FOR INSTALLATION USING DECK PLATE.

Install faucet through deck holes (threaded shank (24) to back). Center faucet on sink with support plate (31) oriented in sink holes. Position spout to the side to keep faucet from tilting forward. Go to step 4b for installation of mounting bracket (32).

(1)

(2)

(3a)

INS115D

(3a)

3b.FOR INSTALLATION USING SMALL ROUND DECK

RING. Place round deck gasket (29) under the small round deck ring (28). Place deck ring over hose (34) and supply tubes (26) of faucet assembly.

4. For both installations, align the faucet assembly with

the threaded discharge tube (24) in the back. Align tabs on faucet to holes in deck plate (27) or deck ring (28). Place assembly down through sink while pushing assembly toward back of sink as far as possible.

5. A groove in the treaded discharge tube (24) indicates the

minimum amount of thread lenght which must be exposed for proper attachment of mounting nut (33) and hose.

5a. FOR INSTALLATION WHERE THE DECK IS LESS

THAN 7/8”, install mounting bracket (32) (open side up) by hooking around supply tubes, as shown, and sliding up and onto threaded discharge tube (24).

Mounting bracket (32) can be easily installed onto threaded discharge tube by gently pulling the supply tubes forward away from the discharge tube, making sure not to kink the tubing. Install and HAND TIGHTEN medium mounting nut (33).

5b.FOR INSTALLATION WHERE THE DECK IS

GREATER THAN 7/8”, turn the mounting

bracket over (open side down). Install and HAND TIGHTEN medium mounting nut (33). Be sure the faucet is aligned properly with threaded discharge tube directly in back.

6. Rotate the spout receptor (15) to the

left and right, noting where it stops. Faucet should extend to the left and right from center equally. To readjust, untighten medium mounting nut (33) then move spout receptor to desired rotation. Hand tighten medium mounting nut.

Check movement of hose before final tightening of nuts. If hose does not move freely, gently bend the supply tubes (26) out. Do not kink supply tubes. Tighten mounting nut (33) with the tool (36) provided. Use heavy duty screwdriver through the holes in the bottom of the tool to tighten faucet securely. Recheck for alignment, be sure that the faucet is centered properly on the sink and that it does not shift position when the spout is moved from side to side.

7. Assemble hose (34) to threaded discharge tube (24) and

tighten with adjustable wrench.

(3b)

(5a)

(<7/8”)

(5b)

(>7/8”)

(7)

➤

SINK

INS115D

HELPLINE: 1-800-BUY-MOEN

INS115D

HELPLINE: 1-800-BUY-MOEN

8. Counterweight (35) is designed to snap together onto the

spout hose. To disassemble counterweight, depress tabs and pull halves apart, or pry halves apart with flat-head screwdriver. Assemble counter weight at the bottom of the spout hose loop. Align tabs on each half of the counterweight with the slots on the other half of the counterweight. Squeeze halves together until they snaptogether. Counter weight should not slide on the hose..

CAUTION: Severe bends of the supply tubes may cause crimping. Restricted water flow could result.

9. CAREFULLY bend the supply tubes

and align with water supply lines. DO NOT KINK SUPPLY TUBES. Connect your water supply lines to threaded fittings (30) (using large nuts (38) if necessary). Hot water supply tube is the longer tube (on left). Hold threaded fitting with a wrench to prevent twisting and collapse of the copper tube while tightening with another wrench.

10.Pull pullout spout in and out to check for free movement of hose. If needed,

adjust the placement of weight to aid the clearance of the hose.

11.Faucet flushing is required before installation is complete. (See below)

LINE FLUSHING INSTRUCTIONS

IMPORTANT: Pipe chips, sand, stones and other solids found in new and renovated plumbing can damage the sealing surfaces of the filter cartridge and cause a leak. To avoid damage, DO NOT TURN ON SUPPLY VALVES until instructed below.

1. Pull hose out of spout receptor, tie a cloth around the hose to keep it from

slipping back into the spout receptor.

2. Unscrew the hose from the bottom of the quarter turn connector (18) and

remove screen washer. Turn on supply valves. Direct hose into sink, then turn the faucet on in the full cold position (handle pointing to the right) to turn on the cold water supply for 3-5 minutes.

3. Leaving the handle in the open position, turn to the full hot position (handle

pointing to the left) and turn on the hot water supply for 3-5 minutes.

4. Place handle in the closed position. Remove the quarter turn connector (18)

from pullout spout and reassemble with screen washer to hose. Do not reassemble pullout spout to quarter turn connector since MicroTech filter installation is required. Check under the sink for system leaks.

(9)

INS115D

HELPLINE: 1-800-BUY-MOEN

MICROTECH™ FILTER INSTALLATION

NOTE: Faucet will not operate in any mode without filter. Filter should be left in protective bag until ready for installation. The MicroTech™ filter is a high performance carbon block filter developed specially for the PureTouch Filtering Faucet System. Once the filter is installed in the pullout spout, it should not be

removed until it is to be replaced. The electronic module keeps track of the amount of filter life remaining and will signal you when the filter change is necessary. If a partially used filter is removed and reinstalled, the electronic indicator will automatically reset and will not accurately reflect filter life remaining.

Use only MicroTech filter cartridges with the PureTouch Filtering Faucet System

1. Remove the filter cover by lifting it up and away from the pullout spout body.

2. Insert the new filter by aligning the outlet tubes on the filter with the inlet ports of the spout body and gently pressing in and down. Upon successful installation of the filter cartridge, the filter life indicator will beep three times and reset automatically. (Do not remove the filter

until it is to be replaced.)

3. Reinstall the filter cover by positioning the alignment tab with the corresponding notch in the main pullout spout body and gently pushing in and down.

4. Attach the pullout spout to the hose by aligning the dots on the quarter turn connector (18) and the spout. Push the quarter turn connector onto the spout assembly and turn it clockwise, locking it in place.

5. Allow cold water to run through the new filter for 5 minutes to flush out any loose carbon particles. (See page 9 for filtered water mode.) Once these small black particles are washed out the filter is ready for use.

The PureTouch System installation is now complete. Please read carefully the operation instructions to ensure optimal performance.

CARE AND MAINTENANCE

All that is needed to clean your faucet is a soft damp cloth. Moen does not recommend the use of scour pads, cleansers or chemicals. The abrasive nature of these substances could damage the faucet’s finish. A non abrasive car wax will help to protect the finish. DO NOT PLACE WAND APPLIANCE IN DISHWASHER.

ALIGN

DOTS

(2)

(3)

(4)

INS115D

HELPLINE: 1-800-BUY-MOEN

OPERATING INSTRUCTIONS

Controlling The Water

The PureTouch System has three options for water delivery; unfiltered stream, unfiltered spray and filtered water.

The spray and stream actuating buttons are on the sides of the pullout spout, the filtered water button is located on the front of the spout.

Stream/Spray flow rate = 2.2gpm maximum at 60psi / 2.5gpm maximum at 80psi.

STREAM MODE

: Unfiltered water in regular

stream flow.

When the water is turned on at the faucet, the spout will always begin operating in the regular stream mode.

SPRA

Y MODE: Unfiltered water in a wide

pattern.

If a wide spray mode is desired, push the spray button while the water is on. To return to stream mode, push the stream button.

FIL

TERED WATER MODE: Filtered water

dispensed through the separate filtered water outlet.

Pressing the front filtered water button will divert water through the filter and dispense filtered water from a separate outlet. The only way to exit the filter mode is to shut the faucet off.

CAUTION: Only filter cold water. Do not filter water above 100° F.

Electronic Indicator

The electronic indicator provides the following visual and audible feedback on the filtering system:

• Successful installation of a new filter (audible & visual)

• Percent of filter life remaining (visual)

• Filter is actively filtering water (visual)

• Low filter warning (audible & visual)

• Depleted filter warning (audible & visual)

• Low battery warning (audible & visual) The electronic indicator is powered by a replaceable, standard 3V lithium watch battery (2032) designed to last several years.

Cont’d

INS115D

HELPLINE: 1-800-BUY-MOEN

OPERATING INSTRUCTIONS

Electronic Indicator cont’d

Successful Installation of a new Filter

When the depleted filter is replaced with a new filter three beeps are sounded and the 100% filter life is displayed momentarily. The new filter has been successfully installed and the electronic indicator has reset.

Percent of Filter Life Remaining

As the filter is used the indicator counts down to zero from 100%. The percentage remaining is displayed when water is being filtered. Additionally, the filter status can be checked without the faucet being turned on by momentarily pressing the filter button.

Filter is Actively Filtering Water

The water drop icon cycles when water is being filtered.

Low Filter Warning

There are two low filter warnings; one at 5% remaining filter life and 1% remaining life. When the remaining filter life reaches 5% the low filter icon blinks and three beeps are sounded when the filter button is depressed. At 1% or less the low filter icon blinks and beeps are sounded every 5 seconds while water is being filtered indicating it is time to change the filter.

Depleted Filter Warning

When the filter life remaining reaches 0%, the depleted filter icon blinks and beeps are continuously sounded while water is being filtered. The filter mode should not be used until a new filter is installed.

Low Battery Warning

The electronic indicator is powered by a standard 3V lithium watch battery designed to last several years under normal usage. When a low battery condition is detected the low battery icon blinks and beeps are sounded while water is being filtered indicating it is time to change the battery.

Low filter

icon

OPERATING INSTRUCTIONS

Helpful Tools: large flat tip screwdriver, small Phillips screwdriver (#1)

Battery and Upper Housing Replacement

1. With faucet off, push filtered water button and

record percentage of remaining usable filter life. When battery is changed, filter life indicator automatically resets to 100%. Record here _____

2. Remove pullout spout (19) from receptor (15)

and tie a dish towel around the hose to keep it from slipping back into the spout receptor.

3. Disconnect the quarter turn connector (18) from

spout by turning it counterclockwise one quarter turn. The quarter turn connector will remain attached to the hose.

4. Remove filter cover by lifting up and away from

main spout assembly. Remove filter cartridge from main spout assembly by lifting from the inlet tube, using same up and away motion. NOTE: Excess water may dribble from cartridge and valving. Dry pullout spout with towel to prevent electronics from becoming wet.

5. With large flat screwdriver or dime, unscrew

(counterclockwise) and remove filter outlet nut (21).

6. With Phillips screwdriver unscrew (counterclockwise)

and remove two short lower housing screws. Carefully remove lower housing cover.

7. Unscrew (counterclockwise) and remove three

upper housing screws. Carefully lift upper housing cover off of wand appliance leaving rubber button covers in place.

8. Battery should now be exposed on upper side

of spout. Remove old battery from battery compartment and dispose of properly.

9. Install new 2032 battery with positive side

(+) up. When battery is properly installed, filter life indicator will light momentarily. Activate electronic indicator by pressing filtered water button to ensure proper battery installation. Display should be visible.

10.Reinstall upper housing cover by carefully aligning

over button covers.

cont’d

HELPLINE: 1-800-BUY-MOEN

(3)

(4)

(1)

(5 & 14)

(7 & 11)

(7 & 10)

(6 & 12)

FILTER COVER

LONG SCREW

ELECTRONIC

INDICATOR

FILTERED

WATER

BUTTON

UPPER HOUSING

SCREWS

(6 & 13)

INS115D

HELPLINE: 1-800-BUY-MOEN

OPERATING INSTRUCTIONS

Battery Replacement cont’d

NOTE: When reinstalling screws and filter outlet nut, insert into hole, turn counter clockwise with screwdriver until a click is felt then turn clockwise until snug. DO NOT OVERTIGHTEN!

11. Reinstall 2 short and 1 long upper housing screws until snug. Refer to picture

(7&11) on previous page for placement of long screw. DO NOT OVERTIGHTEN!

NOTE: To assist in aligning lower housing, press side buttons slightly while sliding housing in place.

12. Reinstall lower housing by carefully aligning over button covers.

13. Reinstall two short lower housing screws until snug. DO NOT OVERTIGHTEN!

14. Reinstall filter outlet nut (21) with flat screwdriver. DO NOT OVERTIGHTEN!

15. Insert filter by aligning outlet tubes with inlet ports on main pullout spout

assembly and gently pushing in and down. Upon successful installation of filter cartridge, pullout spout will emit a series of three beeps and filter life indicator will reset automatically.

16. Reinstall filter cover by positioning alignment

tab over corresponding notch in main pullout spout assembly and gently pushing in and down.

17. Reattach quarter turn connector (18) to pullout

spout (19) aligning the dots on the quarter turn connector and the spout. Push the quarter turn connector onto the spout assembly and turn it clockwise, locking it in place. Return spout to the receptor.

18. If new filter was not installed at battery change, refer

to remaining filter life previously recorded at beginning of battery replacement. Subtract recorded number in step 1 from the 100% displayed. The difference represents the display setting at which the current filter will need replacement. Filter may not perform as desired after this calculation percentage.

Example: Remaining filter life prior to battery change equals 30%.

Subtract 30% from 100% (100 - 30 = 70).

Filter will need to be changed when indicator reads 70%.

(8)

(16)

(17)

ALIGN

DOTS

INS115D

HELPLINE: 1-800-BUY-MOEN

FILTER REPLACEMENT

MicroTech™ replacement filter cartridges may be purchased at the same location as the faucet. For the dealer nearest you, call 1-800-BUY-MOEN. Use only MicroTech filter cartridges with the PureTouch

Filtering Faucet System.

Do not remove the filter until it is to be replaced.

1. Remove pullout spout (19) from receptor (15)

and tie a dish towel around the hose to keep it from slipping back into the spout receptor.

2. Disconnect the quarter turn connector (18) from

pullout spout by turning it counterclockwise one quarter turn. Quarter turn connector will remain on the hose.

3. Remove the filter cover by lifting it up and away

from the pullout spout assembly. Remove the filter by lifting it up and away from the pullout spout assembly. NOTE: Excess water may dribble from cartridge and valving.

4. Using soft towel or cloth, wipe excess water

from wand appliance.

5 Insert the new filter by aligning the two outlet

tubes on the filter with the two inlet ports of the spout body and gently pressing in and down. Upon successful installation of the filter cartridge, the pullout spout will beep three times and the filter life indicator will reset automatically.

6. Reinstall the filter cover by positioning the

alignment tab with the corresponding notch in the main pullout spout body and gently pushing in and down.

7. Reattach the filtering pullout spout to the hose

by aligning the dots on the quarter turn connector (18) and the pullout spout (19). Push the quarter turn connector onto the pullout spout assembly and turn it clockwise locking it in place.

8. Allow water to run through the new filter for 5

minutes to flush out any loose carbon particles. After these small black particles are washed out the filter is ready to be used.

ALIGN DOTS

(7)

(6)

(3)

(2)

FILTER COVER

TROUBLESHOOTING

PROBLEM: Water drips from hose and quarter turn connection. SOLUTION: Make sure screen washer (17) is in place.

PROBLEM: Slow or uneven water flow in unfiltered modes. SOLUTION: The screen washer has become clogged. Ensure faucet handle is in a

closed position. Remove pullout spout from receptor and tie a rag around the hose to keep it from slipping back into the spout receptor. Disconnect the quarter turn connector (18) from hose connection (16). Remove screen washer (17) from hose connection. Clean screen washer with a toothbrush and rinse.

PROBLEM: Reversed Hot & Cold positions. SOLUTION: HELPFUL HINTS: IT IS NOT NECESSARY TO SHUT OFF WATER.

SUPPLIES. HANDLE SCREW REQUIRES A 7/64” HEX KEY WRENCH.

1. Remove plug button (3) from the handle by prying the button upwards from the bottom center. If a tool is required, use something which will not scratch the handle. Remove set screw (2), handle body (1), dome (4), cartridge screw (5), handle adapter (6) and handle connector (7).

2. Turn cartridge stem around so that the notch is turned one half turn or 180°.

3. Reinstall as follows: Be sure retainer clip (13) is present on cartridge stem and raised edge of pivot stop (10) faces front. Note orientation of handle adapter & connector assembly

(6 & 7) in the exploded view. Completely turn cartridge screw (5) to prevent unwanted closure of faucet. Thread on dome clockwise until hand tight. Reinstall handle body (1), set screw (2) and plug button (3).

PROBLEM: Pullout hose does not move freely. SOLUTION: Gently bend supply tubes away from the hose. DO NOT KINK

SUPPLY TUBES.

PROBLEM: Slow or uneven water flow in filtered mode. SOLUTION: Filter outlet nut (21) may be clogged.

1). Remove filter outlet nut, flush out carbon particles.

2). Filter cartridge may be clogged with captured contaminants. Replace filter cartridge. If problem persists call Moen Helpline at 1-800-BUY-MOEN

PROBLEM: Water drains from sides of pullout spout when water is on. SOLUTION: Filter may be cracked. Replace filter.

PROBLEM: Electronic display doesn’t function. SOLUTION: Replace battery.

INS115D

HELPLINE: 1-800-BUY-MOEN

➤

TURN STEM

1/2 TURN

NOTCHED

FLAT

ON STEM

➤

+ 33 hidden pages