Culligan 01020553, 01020606 User Manual

Download

Page 1

CULLIGAN

Cat. No. 01021161

Rev. A 10/16/08

DCO # 010703

Installation,

Operating and

Service

Instructions

Global Electronic (GBE) Softener & Filter Controller

For Commercial/Industrial Applications

Models from 2008

Printed in USA

Page 2

Read this Manual First

Before you operate the Culligan Global Controller, read this manual to become familiar with the device and its capabilities.

Watch for Special Paragraphs

Please read the special paragraphs in this manual. Examples are shown below.

NOTE A Note provides information or highlights a procedure.

CAUTION

A Caution tells how failing to follow instructions might cause injury or damage the equipment in some way.

About this Manual

Contents

This manual:

• familiarizes the operator with the equipment

• explains installation and setup procedures

• provides basic programming information

• explains the various modes of operation

• gives specifications and troubleshooting information

WARNING! Electrical shock hazard! Unplug the unit before removing the cover or accessing any internal control parts.

WARNING! This device complies with part 15 of the FCC rules subject to the two following conditions: 1) This device may not cause harmful interference 2) this device must accept all interference received including interference that may cause undesired operation.

CAUTION! To reduce the risk of fire, use only No. 26 AWG or larger telecommunicaitons line cord.

This equipment complies with Part 15 of the FCC rules. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Products manufactured and marketed by Culligan International Company (Culligan) and its affiliates are protected by patents issued or pending in the United States and other countries. Culligan reserves the right to change the specifications referred to in this literature at any time, without prior notice. Culligan, AquaSensor, Tripl-Hull, and SoftMinder are trademarks of Culligan International Company or its affiliates.

The product is covered by the following patents: Softener and/or filter: US 5073255, 5273070, 6457698, 4534867: Israel 095754 Sensor option: US 5699272 Other US and foreign patents pending.

i CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 3

Installation,

Operating and

Service

Instructions

CULLIGAN

GLOBAL ELECTRONIC (GBE) SOFTENER & FILTER CONTROLLER

Table of Contents . . . . . . . . . . . . . . . .Page

Important Safety Information ....................................... i

Controller Features ..................................................1-2

Operation ....................................................................3

Installation ...............................................................4-6

Wiring Schematics .................................................7-17

Circuit Board Layout ..............................................7

Transformer ........................................................8-9

Brine Refill Valve ................................................. 10

Communication Cable ......................................... 11

Progressive/ Parallel Flow ...................................12

Alternating ...........................................................13

Flow Meters .........................................................14

Aqua-Sensor ........................................................15

Aux Outputs .........................................................16

Aux Input .............................................................17

Programming .......................................................18-20

Key Pad Operation .............................................19-20

Overview...................................................................21

Commercial Setup .................................................... 22

First Time Setup ..................................................23-27

Customizing the Setup ........................................28-32

Progressive Flow .................................................29

Regeneration .......................................................30

Cycle Times .........................................................31

Regeneration Triggers .........................................32

Installation of Accessories ...................................33-45

Aqua-Sensor ........................................................33

Beeper Mode .......................................................33

Smart brine Tank Sensor ....................................34

Wireless Remote ............................................35-37

Modem ............................................................37-41

Low Meter ............................................................41

Progressive Flow ............................................41-42

Brine Reclaim .................................................42-43

Service Phone Number ......................................44

Auxiliary Boards ..................................................46-48

Manual Regeneration ...............................................49

Manual Cycling ......................................................... 50

System Information .............................................51-52

Error & Alert Codes ..................................................53

Diagnostics / Statistics ........................................54-57

Check Sensors ....................................................55-57

Menu Lockout ........................................................... 58

Menu Flow Chart .................................................59-62

Appendix A - Meter K-Factors ..................................63

Appendix B - Parts & Accessories ..........................64

Appendix C - PLC Output....................................65-68

Appendix D - Control Settings ..................................69

Index .........................................................................70

TABLE OF CONTENTS ii

Page 4

Controller Features

The Culligan Global Electronic control (GBE) primary function is to initiate and control the regeneration process via methods that are most convenient and cost effective for the customer while offering many operational features and benefits. The controller is designed to operate a wide range of existing and new softener and filtration valves.

Take control of your system and your productivity

The Culligan Global Electronic Controller (GBE) is an advanced design engineered to handle regeneration and monitoring of your water treatment equipment. It offers powerful programming options that can be used to operate and monitor any softener or filter system. It also provides sensing capabilities, expanded communications and a multifunction keypad—all in one simple to use unit.

GBE Controller Features

Advanced Lighted OLED Display

•

The user is guided through brightly lit graphical menu screens with clear, multi-line, full text prompts

Membrane Keypad

•

The keypad uses sealed contacts for programming. No buttons to get dirty

Program Beeper

•

Emits an audible beep when keys are depressed to help identify valid (short beep) or invalid (3 short beeps) pushes. Can be enabled or disabled.

Power Source

•

Electrical power required is 24 Volt 50/60 Hz AC current. A UL listed plug-in transformer (120V/24V) is provided.

Time of Day

•

Displays current time of day in either 12-hour or 24 hour format

Real Time Clock with a 5 Year Battery Back-up

•

Keeps accurate time even during a power outage. Updates automatically when the GBE is equipped with optional modem capability

English or Metric Values

•

Displays can be set to either English or Metric

Regeneration Interval

•

Provides the ability to initiate a time clock regeneration based on a number of days (1 to 99) or a specific day of the week.

Regeneration Start Delay

•

Allows a user determined number of hours (0-9) to be set for the purpose of increasing the amount of time between regenerations in a multi unit installation.

Auxiliary Input

•

Capable of accepting a remote signal from a dry contact device such as an operator push button for the purpose of initiating a regeneration sequence

Auxiliary Output on Alarm

•

Capable of sending a signal when an alarm/error is recognized

Expansion Board for Additional Outputs

•

o Control blocking valves o Control external solenoids or chemical feeders

Figure 1

Figure 2

1 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 5

Progressive Flow Trip Point

•

Allows multiple tank systems operating with flow meters to bring tanks on-line or off-line as facility flow demands increase or decrease

Multiple Unit Communication

•

A communication cable interconnects multiple units to operate the controller in the Progressive Flow mode and prohibits them from regenerating at the same time.

Diagnostics

• The user can check the operation of sensors, progressive flow communication, motor positions, or an optional wireless display

Transformer is UL and CUL Listed

• RoHS Compliant

•

Optional GBE Features

Flow Meter/Sensor Input

•

Supports various types of Hall effect flow sensors using a programmable “K” factor to initiate a regeneration sequence

AquaSensor Input

•

Supports the patented digital Culligan AquaSensor technology used to efficiently initiate and control a regeneration sequence

Telephone Modem

•

o Calls in reports on regenerations and alarm conditions o Automatically updates time and date when calling in o Automatically checks for and installs and firmware updates when calling in

Wireless Remote Display

•

Displays the current status of the unit. It can be located up to 200 feet away from the GBE controller (depending on building and interference). The telephone modem can optionally be installed in the remote display

Smart Brine Tank Probe

•

This probe monitors conditions inside the brine tank.

o Predicts when more salt is needed o Detects the presence of a salt bridge o Detects eductor line plugging o Signals brine tank overfilling condition

Controller Features

CONTROLLER FEATURES 2

Page 6

Operation

Modes of Operation

Time Clock

The controller will initiate a regeneration based upon a time schedule of intervals of days (i.e., every 3 days) or on a specific day of week schedule (i.e., Mondays, Wednesdays and Saturdays). Because regeneration will occur at the prescribed schedule regardless of water use, this method is usually the most inefficient method of water softener operation.

Flow Meter/Sensor

When a flow meter or sensor is connected to the controller circuit board, the controller has the ability to measure the amount of water treated and initiate a regeneration sequence based upon the gallon capacity of the water treatment equipment. The controller can delay the regeneration signal until a convenient time of day (known as a delayed regeneration) or act and initiate the regeneration sequence as soon as the signal is received (known as immediate regeneration).

When installing an alternating duplex system (one tank on-line, the other in standby), only one flow measuring device is required to be installed in the common outlet header of the system. Parallel systems (multiple tank systems, all on-line simultaneously) require one flow device for each mineral tank in the system.

This method is a proven, cost effective means to operate a water softening system.

Aqua-Sensor (Softener use only)

The Aqua-Sensor detects when a softener resin bed has reached its point of exhaustion and, as a result, initiate a regeneration sequence. This is the most cost-effective method of operation and may be combined with any of the operational modes previously described.

Progressive Flow

The Progressive Flow mode is used with up to six and as few as two mineral tanks in a system. It allows more than one tank in a system to either be on-line or off-line depending upon the downstream flow demand. If flow demand is greater than the flow capability of the tank on-line, another tank can be brought on-line to help satisfy the excess demand. Once the demand has decreased, the second tank is returned to a standby mode and the system reverts to just one tank on-line providing treated water.

The progressive flow mode of operation relies on a user programmable set point or Trip Point. The Trip Point is a unit of flow (gallons or liters) on a per minute basis. Once attained the trip point will cause the second unit (in multiple resin tank system) to come on-line. Each additional tank in the system will subsequently be brought on-line as multiples of the trip point are attained. (Example: a 3 tank system with a trip point of 50 gpm will bring two tanks on-line once the facility flow demands is equal to or greater than the 50 gpm trip point. Should the flow demand reach 100 gpm or more, the third tank shall be brought on-line.)

Additional tanks shall be returned to stand-by once the facility flow demand is <95% of the trip point for two tank systems, <95% of 2X the trip point for triplex systems and <95% of 3X the trip point for quad systems, and remains there for 60 seconds.

Utilizing the progressive flow feature may allow the owner to use smaller units, resulting in the potential for reduced capital and operation costs.

Differential Pressure (Filters only)

When combined with an optional differential pressure device, the Culligan MVP controller has the ability to initiate a backwashing sequence when the pressure differential across the media bed reaches a preset amount (usually 8 to 10 psi).

3 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 7

Installation

ELECTRICAL INSTALLATION

CAUTION!

Observe the precautions listed below before electrical installation of your GBE controller. Failure to do so may cause permanent damage to the controller.

1. Follow the local electrical code requirements.

2. Be sure electrical power is off and disconnected at the source before completing any wiring/cabling connections.

3. Provide a dedicated 120-volt circuit for the GBE system to ensure maximum electrical protection.

4. DO NOT include the GBE wiring cables in any conduit or raceway containing other 120-volt or higher circuits.

5. Maintain a distance of at least 10 feet between the GBE controller and any electrical distribution panels, raceways carrying 300 volts or more, and electrical motors of 1 horsepower or more.

6. Use the cabling provided. Failure to do so may effect performance of the GBE controller adversely.

Note: One transformer is required for each controller in the system. Do not attempt to operate multiple

controllers without a dedicated transformer for each or your system will experience operational

difficulties.

Installation 4

Page 8

Installation

WIRING PROCEDURES AND DIAGRAMS

Preparation

1. Loosen the screws or latches securing the controller access cover (Figure 3 or 4) on each controller provided.

2. Using a small screwdriver, loosen all the terminal strip binding screws on the main circuit board that do not contain wires by turning counterclockwise until the wire clamp has been fully opened (see Figure 5).

Figure 3

Figure 4

Figure 5

5 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 9

Installation

Cable Routing

All input and output connections to the circuit board are 24 volt or less.

Although the cables do not have to be run in conduit, it is necessary that long runs of cable be supported or protected by strapping them to the equipment piping. If conduit will be used to route the shielded cables, three factors must be considered:

1. DO NOT share the same conduit or raceway with 120 volt or higher circuits.

2. Keep cables at least 6 inches away from 120 volt or higher electrical circuits.

3. GROUND the conduit (if metallic) to a known “earth ground” location.

A series of holes are located on the sides of the controller (see Figure 6 and 7). Strain relief fittings are provided with the controller enclosure for interconnecting wiring. Install the plastic fittings as needed. Remove the compression nut and rubber sleeve from each fitting. Prior to connection of the cable wires to the circuit board, slide the compression nut and sleeve over the cable for the wiring connections. When wiring is completed, apply a small amount of silicone to the rubber sleeve and reassemble. This will assure all wiring is secure and assist in making the tightening of the fitting easier. Insert the plugs provided to block any holes not used for wiring or other accessories.

Right Side View

Left Side View

Brine Reclaim Solenoid (optional)

Input Connection for Flow Sensor

Output Connection for Remote Accessories

Input Connection for Remote Accessories

24 Volt Power Input Connection

Brine Reclaim Solenoid (optional)

Brine Refill Valve

Figure 6 Figure 7

Blocking Solenoid for Alternating Operation

Installation 6

Page 10

Schematic

GBE Circuit Board Layout–Front

OLED Display

Battery CR2032 (Postitive Side Up)

Keypad connector

Figure 8

GBE Circuit Board Layout–Back

Phone line

connection

(optional)

Motor position cable

Multiple unit jumper

Communication cable (optional)

Flow meter cable

(optional)

Smart Brine Tank cable (optional)

External regeneration

signal connection (optional)

Figure 9

7 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Motor

connection

Programmable outputs (optional)

Blocking valve connection (optional)

Data port

Future use

Do not connect anything to these.

Aqua-Sensor cable (optional)

Power cable from transformer

Page 11

Outputs

Schematic

CAUTION Connecting 24V to the 2.5v connection on the circuit board will damage the circuit board.

The circuit board supports four outputs:

• Motor control (DC Motor)

• Blocking valve (Use Aux Out 4)

• Four programmable auxiliary outputs (Aux Out 1 through 4)

• Controller interface (communication between multiple controllers) (RS485).

Note: If you are using Aqua-Sensor, you should run the 2.5v wiring now as the cable is run through the same cord grip.

See page 15 for details.

1. Locate the power cord among the controller parts. It has a white connector on one end and two spade connectors on the other.

2. Locate the cord grip among the parts.

3. To assemble the power cord, first run the cord grip nut over the spade terminal end of the power cord.

4. Next, run the spade terminals through a hole in the side of the controller FROM THE INSIDE. See figure 10.

5. Finally, run the cable through the bottom end of the cord grip, and assemble the grip to the controller wall.

6. Plug the board connector to the board where it says “24v”. The connector has four (4) connections but only two wires are connected. The other end of the power cord (with spade terminals) should be connected to the two 24VAC terminals on the transformer (see figure 12).

DO NOT PLUG THE TRANSFORMER INTO THE WALL UNTIL ALL WIRING IS COMPLETED.

Repeat the process for any additional units in the system.

Schematic 8

Page 12

Schematic

METAL TABS

Connect to white connector on main power cord

If using Aqua-Sensor, plug metal tabs at end of cord into connector

24V Transformer

The GBE control is powered by a 24V/50VA transformer. If there are multiple controls in the system being installed, each control will require its own transformer. It is recommended that the transformer be plugged into a dedicated 120V circuit.

CAUTION Connecting 24V to the 2.5V connection on the circuit board will damage the circuit board

1. Connect one wire from the 24V cable to the outermost 24VAC transformer screw terminal (Reference Figure 12). The other end of the wire should be connected to one of the 24V terminals on the GBE control circuit board (Figure 11) by way of the white connector.

2. Repeat the process for the other 24V power supply wire attaching the second wire to the opposite terminal on the transformer and next to the other wire connected to the 24V pins on the GBE board.

24V Power Connection

Figure 10

Transformer connection

Figure 11

9 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

POWER SUPPLY

ONE transformer is required for each Control

2.5VAC Aqua-Sensor Power Terminals

24VAC Power

Terminals

Figure 12

Page 13

Brine Refill Valve Wiring

Solenoid

Coil

Screw

Plastic

Spacer

2.5VAC

P9 Power

24VAC

Vlv

Aux1

Sol

Aux2

P8P5

Cam

P10

Snsr

Aqua

Meter

Flow

Aux

LCD

TRIM OFF GREEN WIRE

BLACK

WHITE

REFILL SOLENOID VALVE

CIRCUIT BOARD

MVP

*This only applies to Culligan CSM Softeners.

1. Installation of the solenoid coil and connector

Locate the solenoid coil and connector cord. Assemble it

to the brine refill valve as shown in Figure 13.

Schematic

Figure 13

2. Installation of the cord grip

Remove the hole plug from the left side of the MVP

controller enclosure. Locate the cord grip fitting and nut. Assemble them through the open hole and thread the solenoid coil cord through the cord grip fitting as shown in Figure 14. Tighten the cord grip onto the cord.

3. Wiring

Wire the valve to Aux Out 2 as shown in the diagram in

Figure 15. The wires can be trimmed to a suitable length.

Figure 14

Figure 15

Schematic 10

Page 14

Schematic

SO L

Communication Cable - Multiple Units

NOTE: Disregard this information and proceed to flow sensor schematic (optional) information when installing single tank configurations.

Multiple units require a communication cable between each unit. Refer to the table below for the cable type, part number and quantity required. Cables are attached to the RS485 terminal of the circuit board.

Table 2

System Configuration

Duplex Alternating 01016342 1 01016369 2

Duplex Parallel 01016327 1 N/A 0

Triplex Parallel 01016327 2 N/A 0

Duplex Progressive 01016327 1 01016333 2

Triplex Progressive 01016327 2 01016334 3

Multiple units can be set up as progressive flow, alternating or parallel operation. Refer to the instructions and schematics below and on the following pages for connection to the circuit board.

Cable Part Number Qty of Cables

required

“Kit” Part Number Qty of blocking

solenoids used.

Most multiple tank configurations will also require blocking valves (with the exception of the Hi-Flo 3e softener). These are used to hold tanks offline until needed. Based on the chart above, you can determine how many blocking solenoids are used. These solenoids are included in the alternating and progressive flow kits.

Blocking Solenoid Connection (used on Alternating and Progressive flow systems)

The solenoid valve wiring attaches to the Aux Out 4 output connection on the auxiliary circuit board. See Figure 16 .

Figure 16

11 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 15

Progressive Flow or Parallel Flow

To RS 485 Comm Port on GBE Circuit Board, #1

CABLE 01016327

To RS 485 Comm Port on GBE Circuit Board, #2

PARALLEL

Additional communication cable connections are used when there are 3 or more controls. Connect end of 2nd-(01016327) cable to this connector and other end of cable to RS 485 Comm Port on 3rd GBE Circuit Board.

IMPORTANT Setting the Jumpers for Progressive Flow

For progressive flow to operate properly, the first and last units must have the jumpers set to pins 1 and 2 (see figure at right). All middle units should have the jumpers on pins 2 and 3 (see figure at right). The diagram below (figure 17) shows duplex connections. Repeat the connections on any additional systems.

1 2 3

Schematic

Jumper location for first and last units (end units).

Jumper location for middle units.

Jumper

Location

Communication Cable 01016327

To Additional Units (if necessary)

Unit 1 Unit 2

Flow Meter Flow Meter

Figure 17

Progressive/Parallel Communication Cable 01016327

Schematic 12

Page 16

Schematic

To RS 485Comm Port on GBE Ciruit Board, #1

To Flow Meter Connection on GBE Circuit Board.

CABLE 01016342

Flow Meter Connector (from meter).

To Flow Meter Connection

(on GBE Circuit Board).

To RS 485Comm Port on GBE Ciruit Board, #2

DUPLEX ALTERNATING

Duplex Alternating with Meter option

Communication Cable 01016342

Unit 1 Unit 2

Flow meter

Figure 18

For triplex, quad, etc alternating, you must use a meter on each unit and connect the same way as progressive flow.

Duplex Alternating Cable 01016342

13 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 17

(optional)

2535 & 2536

Signet

Black

Shield

Red

Black

Green

Red

Paddle Wheel (optional)

Seametrics

Green

Red

Black

White

SINGLE OR PROGRESSIVE

Bare

Red

Green

Black

Red

Black

Wht/Clear

2" Autrol Turbine Meter

(optional)

Black

White

Red

2"Clack Meter

(optional)

Schematic

Flow Sensor Meter Connections (Optional)

The GBE Controller is capable of detecting the signal from a Hall effect sensor device to provide flow rate information, totalization and volume based regeneration initiation.

There are several different types of flow measuring devices and differences in the wiring of the devices to the GBE circuit board do exist. Refer to the drawings below.

For all but duplex alternating, a meter needs to be connected to each circuit board at the location shown below in the drawing. For duplex alternating meter connection, please refer back to page 13, Duplex Alternating with meter option.

SEE PAGE 41 FOR PROGRAMMING AND PAGE 63 FOR K FACTORS.

Figure 19

Connector 01010255 included with controller

Connector located at end of meter cable

Schematic 14

Page 18

2.5V

METAL TABS Connect to white connector on main power cord

24VAC on TRANSFORMER

Power to circuit

board 2.5VAC

only required

for Aqua-Sensor

installations

Power to circuit board 24V

Schematic

Red

Black

Blue

White

Aqua-Sensor Schematic (Optional)

The Aqua-Sensor device requires a 2.5 VAC power source. This source is provided via two of the posts on the 24VAC/2.5VAC transformer (see figure 20). The two leads from the transformer are run through the same cable grip as the 24VAC and then must be pushed into the white power connector for connection to the 2.5v power pins on the GBE circuit board.

The wire connector from the Aqua-Sensor probe is then routed through the included cable grip and plugged into the Aqua-Sensor terminal on the GBE circuit board. See below.

Aqua-Sensor

If you are going to install an Aqua-Sensor, you can set up the 2.5V power now.

1. Locate the power cord packed with the Aqua-Sensor. It has two spade terminals on one end of the cable and two metal “slip in” tabs on the other.

2. Locate the cord grip.

3. The cable can be run through the cable grip and wall from either end of the cable. Make sure the end with the metal tabs goes INSIDE the controller. The spade terminals should be coming out the top end of the grip.

4. Locate the connector at the end of the power cord. You may have already plugged it into the board.

5. Press the two metal tabs on the end of the power cord into the open slots on the connector. They will connect to the pins labeled “2.5V’ on the Base Board.The other end of the power cord with the spade terminals should be connected to the two 2.5VAC terminals on the transformer (see figure 20).

CAUTION - Verify wiring from terminals to circuit board are correct before applying power to control. 24vac power must not be applied to the 2.5 vac terminals of the circuit board.

2.5V Aqua-Sensor Power Connection

Figure 20

POWER SUPPLY

ONE transformer is required for each Control

15 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

CAUTION

Connecting 24V to the 2.5V connection on the circuit board will damage the circuit board.

Page 19

Schematic

Auxiliary Outputs (Optional)

The Auxiliary Outputs - reference Figure 21) are output triacs that can be programmed to provide power to a “normally open” (normally no power to auxiliary output until power required) or a “normally closed” contact (user choice). These 24VAC outputs can be used for energizing a relay coil only. (2.1 Amp maximum power draw)

Refer to the section on Programming (page 46) for additional information on the uses of this feature.

Figure 21

Schematic 16

Page 20

NC NO

POLE

NC NO

POLE

SOL

Regen Signal

EXTERNAL SOURCE

24V DPDT

RELAY

DUPLEX ALTERNATING WITH EXTERNAL SOURCE

SOL

Communication Cable

01016327

Schematic

Auxiliary Input (Optional)

One auxiliary input is provided for optional signal devices such as remote push buttons, differential pressure switches, hardness monitors, turbid meters, etc. for the purpose of receiving a regeneration signal.

Select an UN-POWERED contact within the remote device that will close when regeneration is desired. The duration of the switch closure can be as low as 0 seconds; 6 seconds is the recommended minimum and default but can be as long as 999 seconds. The contact must automatically open following the start of a regeneration sequence. Connect this contact to the Aux In terminal shown in Figure 22. The illustration below is an example of how to use an external source to initiate regeneration.

Figure 22

17 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 21

Programming

The programming process requires various types of data input. The following information pertains to calculating the softening capacity of the water softening system. Filters do not have a capacity setting so this section can be skipped when programming a filter.

Capacity Settings

The capacity of a water softener is determined by two factors; resin amount and water chemistry.

Single Tank Systems

Normally a single tank system has enough resin capacity to soften water for a minimum period of 24 hours. Time of regeneration is usually set to occur very early in the morning or at a time when no softened water is required. This is because when the softener is regenerating, hard water is typically bypassed through the system and into the facility if a demand for water if present.

If regeneration is desired at a time of day when there is no water usage then the system must have a “reserve” capacity which must last an entire day if the regeneration signal (time clock, Aqua-Sensor and/or meter) occurs at the beginning of the day. Subtract this reserve capacity from the total capacity to determine “capacity to signal”.

Note: If the reserve capacity is more than 1/3 of the total capacity,

a meter system may not reduce salt consumption relative to a timeclock system.

Multiple Tank Systems

Multiple tank systems offer the benefit of continuous soft water supply. When using the Aqua-Sensor to initiate a regeneration sequence, the system capacity may be set for the maximum amount the system is capable of producing. However multiple tank systems using only water meters and or time clock as the basis for regeneration initiation are recommended to be set up with a 10% reserve capacity. The purpose of the reserve capacity in multiple tank systems is to allow for subtle changes in water chemistry. You will be able to get the reserve capacity during programming.

Determining Batch Set Point

To determine the batch set point for programming the Culligan GBE controller, use the following formula:

Total Capacity - Reserve Capacity Gallons = Hardness

The GBE will calculate this for you automatically. you can use the formula above to verify the setting.

For more information on programming multi-tank systems, see page 41.

Programming 18

Page 22

Programming

Program Data Input

There are a couple of items to note that can make the programming of the Culligan GBE control a little easier. They are:

Slew Rates This term refers to the speed at which the display moves through the input of material. For

example, holding down the up arrow key for (5) seconds when inputting minutes for Time of Day will cause the minutes to pass in (10) minute blocks of time. Press the up arrow or down arrow keys for shorter periods (less than 5 seconds) will slow the rate. To move through the programming slowly, do not hold down the up arrow or the down arrow keys.

Beeper A beeper is available to assist the user by providing an audible tone (about 70 decibels) to

signify valid (0ne beep) and invalid (three beeps) key presses. The beeper can be deactivated in the programming mode. (If error occurs, beep will still be ON even if set to “No” programming.)

Programming Mode Timeout

Program Input Acceptance

If there is no keypad activity for a (3) minute period while in the programming mode, the controller will exit the programming mode and return to the main display. Any setting that was changed prior to the control timing out will revert back the original value. Pressing the check mark key saves the setting.

For programming information to be accepted, the check mark key must be depressed prior

to programming mode timeout.

19 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 23

Navigating the Menus and Keypad

system ok

9:17 am 1-17-08

> 1) information

2) bypass

3) regenerate

4) set time and date

1) information

> 2) bypass

3) regenerate

4) set time and date

1) information

2) bypass

> 3) regenerate

4) set time and date

regeneration

off

This is the “home” screen. Press any key except CANCEL (“x”) takes you to the main menu.

This is the main menu. The pointer shows where you are in the menu. The UP and DOWN arrows move thru the menu.

CANCEL button

Pressing the CHECKMARK key selects that item on the menu.

UP button

CHECK MARK or OK button

DOWN button

regeneration

off

regeneration

now

regeneration

> tonite

regeneration

tonite

> 1) information

2) bypass

3) regenerate

4) set time and date

regeneration tonite

9:18 Am 1-17-08

Here we see the current value for “regeneration” is “OFF”. Press the CHECK MARK turns on the pointer symbol. The pointer indicates that you can change the current value using the arrow keys.

The arrow keys allow you to scroll thru the available options.

Pressing the CHECK MARK key to select the new setting. The pointer symbol turns off to show this is the selected value.

Pressing the CANCEL button from inside the menu always takes you one step closer to the “home” screen.

Now we are back to the home screen. Note that the display has changed to show that regeneration is now scheduled for tonight.

Navigating the Menus and Keypad 20

Page 24

Programming

GBE Controller Programming

The programming for the GBE controller is all menu based. There are 5 top level menus with additional options below each. The top 5 are:

1) INFORMATION

2) MANUAL MODE

3) SET DATE / TIME

4) ACCESSORIES

5) ADVANCED SETUP

Here is a brief explanation of what you will find under each menu

1) INFORMATION Selecting this menu item will scroll through the operating information for the unit.

2) MANUAL MODE Use this menu item to initiate a manual regeneration.

3) SET TIME / DATE Use this menu item to make changes to the time and/or date. This is initially done during first time set up and the information is saved in memory even in the event of a power outage.

4) ACCESSORIES Use this menu item to set up any installed accessories. This includes meters, Aqua-Sensor, Smart Brine Tank probe, Modem, Wireless Remote, Aux In and Aux Outs.

5) ADVANCED SETUP This menu item allows customization of the unit. There are 5 sub-menus which offer customization settings.

1) SYSTEM SETUP

This menu allows customization of many of the initial setup information. Water Hardness, Iron,

Salt Type, Resin Volume are among the settings.

2) REGENERATION SETUP

This menu allows customization of the salt dosage, reserve capacity, regeneration time and

regeneration mode.

3) CYCLE TIMES

This menu allows customization of the units cycle times.

4) REGERATION TRIGGER

This menu allows customization of what can trigger regeneration, the regeneration interval,

predict mode and days of regeneration.

5) DIAGNOSTICS

This menu allows diagnostics to be performed on sensors, wireless, progressive flow, motor

control, data port, phone line (modem) and advanced statistics.

21 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 25

Programming

Typical Commercial Setup

Setting up the GBE for a commercial installation requires a few additional steps. Follow the outline below to make sure everything is covered.

1) Run the first time setup (see pages 24 to 27)

2) Set up accessories (see pages 33) This includes:

• Water Meter (remember to set K Factor)

• Aqua-Sensor

• Aux In

• Aux Outs (needed for multi-tank, brine reclaim and refill on 4-cycle valves)

• Smart Brine Tank Sensor

• Wireless Remote

• Modem

• Service Phone

• External Filter

3) You must tell the controller if it is a multi-tank system. This is under Advanced Setup/System Setup (see pages 29). The MultiTank System setting is set to PROG FLOW for ALL multi-tank systems. Trip point settings will determine how unit operates (progressive, parallel or alternating - page 42).

4) If you are using immediate regeneration, you must change the Reserve Capacity setting under Advanced Setup/REGEN SETUP and the REGEN MODE. See pages 30.

5) Set/Review Cycle Times – This is under Advanced Setup/Cylce Times. Especially check the Brine Draw/ Slow Rinse (BD/RINSE) and the Fast Rinse. 5-cycle valves have separate refill. See pages 31.

6) You need to do this setup procedure on each control in the system. You may want to write down the settings you change.

7) Refer to Appendix D for a quick programming chart.

Programming 22

Page 26

First Time Setup Process

First Set-up Procedure

If at any time you need to re-run First Time Setup - refer to instruction on page 58. After completing the plumbing connections to the water softener, follow these steps to turn on and program the softener controller.

STEP 1: Plug in the wall transformer

STEP 2: Perform the on-display “First Time Setup” process (below)

„ Moves up the menu

‰ Moves down the menu

P Changes the display, accept desired change

X Cancel or exit

1. When a new controller is first turned on, the display shows the following:

First Time Setup

Hit Down Arrow

Controller

Remote

Press the down arrow to move tot he next question.

2. Electronic Serial Number

S/N: 00000123

This screen is very important as it shows the electronic ID number of the controller.

Note: If this unit will be installed with a modem, it is required that this electronic ID number is reported back to Culligan on the IQR form.

Press the DOWN arrow button to change the display to read “Set Month”.

3. Set Month

Set Month

Jan

• If the default selection is correct, press the DOWN arrow to accept that value and move to the next

question.

• If the value displayed is NOT correct then press the CHECK MARK button to change the display to

show a “>” symbol next to the displayed value.

23 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 27

First Time Setup Process

Set Month

> FEB

• Once the desired value is displayed accept the value by pressing the “CHECK MARK” button.

Press the DOWN arrow to accept that value and move to the next question.

4. Set Day

Set Day

• The “>” symbol indicates that this value may be changed by pressing the

UP and DOWN arrow buttons. For example, pressing the DOWN arrow while the “>” mark is displayed changes the display from “JAN” to “FEB”.

• If the value displayed is NOT correct, pressing the “CHECK MARK” button will change the display, to show a “>” symbol next to the displayed value. Use the UP or DOWN arrow to change the setting. Once the desired value is displayed, this value can be accepted by pressing the “CHECK MARK” button.

Press the DOWN arrow to accept that value and move to the next question.

5. Set Year

Set Year

2008

Press the DOWN arrow to accept that value and move to the next question.

6. Set 12 Hour or 24 Hour Clock

12 hr or 24 hr clock

Press the DOWN arrow to accept that value and move to the next question.

First Time Setup Process 24

Page 28

First Time Setup Process

7. Set Hour

Set hour

Press the DOWN arrow to accept that value and move to the next question.

8. Set Minute

Set minute

Press the DOWN arrow to accept that value and move to the next question.

9. Set AM or PM

Set am or pm

7:32 am

Press the DOWN arrow to accept that value and move to the next question.

10. Set Valve Type (4-cycle or 5-cycle)

valve type

4-cycle

CSM and Hi-Flo 50 are 4-cycle valves and Hi-Flo 22 and Hi-Flo 3e are 5-cycle valves.

Press the DOWN arrow to accept that value and move to the next question.

25 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 29

First Time Setup Process

11. Set Units (US-inch or metrics)

units

us-inch

Press the DOWN arrow to accept that value and move to the next question.

12. Set Softener or Filter

is this a softener or filter?

softener

Press the DOWN arrow to accept that value and move to the next question.

13. Set Water Hardness

water hardness

10 grains

Press the DOWN arrow to accept that value and move to the next question.

14. Set Softener Resin Volume

resin volume?

1.0 cu-ft

This value is found in the products installation manual in the specification table.

Press the DOWN arrow to accept that value and move to the next question.

First Time Setup Process 26

Page 30

First Time Setup Process

15. Setup is Complete

system ok

7:32 am 2-1-08

The circuit board microprocessor automatically calculates softener capacity. The control then automatically homes. Contact your Culligan Man if the settings need to be customized.

Note: For all commercial applications, you must adjust the cycle times. Most important is refill time. Refer to the Brine System charts in the product’s installation manual for cycle settings.

27 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 31

Customizing the Setup

The controller is designed to simplify the setup and installation process by making some default recommendations during the Initial Setup. The default settings are designed to be appropriate for most common installations.

Default Settings

Downflow Brining

• Standard Mesh Resin

• Blue/Beige Eductor

•

0.45 GPM Brine Flow Control

• 0 PPM Iron

• > 40 psi water pressure1

• NaCl Salt

• Time of Regen = 2:00 AM

• Regen Time = Delayed

• Dosage (calculated)

• Predict Mode ON

• 30% Reserve Capacity

• Time Clock Backup = OFF

• Day-of-week Regen = OFF

• Pre-Rinse Mode = OFF1

•

= these items are changed on the Main Menu / Advanced / System Setup Menu

= these items are changed on the Main Menu / Advanced / Regen Setup Menu

= these items are changed on the Main Menu / Advanced / Regen Trigger Menu

There may be times when the installer would prefer to override the default regeneration selections. See Advanced Setup Menu, Regeneration Setup Menu or Regeneration Trigger Menu for information on changing default selections.

Advanced System Set-up Menu

• Press the UP „ or DOWN ‰ arrow to scroll to menu item

• Press the CHECKMARK P key to select a menu item

• Press the UP „ or DOWN ‰ arrow to change a selection

• Press the CHECKMARK P key to save your selection

Default Values are shown for each selection

system ok

7:32 am 2-1-08

> 5) Adv Setup

> 1) system Setup

Scroll to ADV SETUP and select

Select SYSTEM SETUP

Customizing the Setup 28

Page 32

Customizing the Setup

valve type

4-cycle

resin type

standard

hardness gpg

dial-a

softness a

iron

present 0 ppm

line pressure

above 40 psi

salt type

nacl

The GBE controller can operate several types of valves. Select from 4-CYCLE, 5-CYCLE or GBV. For Softeners: For Filters: CSM and Hi-Flo 50 are 5-CYCLE All are 4-CYCLE Hi-Flo 22 and Hi-Flo 3e are 4-CYCLE

The type of resin changes how the GBE calculates capacity. Select from STANDARD or FINE. Unless you change from the standard Cullex®, leave this at STANDARD.

Enter the water hardness (softeners only). This can be from an onsite test or from a water analysis. Enter in the units shown on screen. For US-INCH, enter the hardness in grains per gallon (gpg).

This does NOT APPLY to commercial valves. Leave this set to A.

Enter the amount of iron present. This value can come from an onsite test or a water analysis. Enter the value in ppm (mg/l).

This setting is either ABOVE or BELOW 40 PSI. If the pressure is below 40 psi, the brine rinse time will be extended. This can be overridden by setting the brine rinse time manually by

going to 5) ADV SETUP, then 3) CYCLE TIMES.

Either standard sodium chloride (NACL) salt or potassium chloride (KCL) salt can be used. The

GBE needs to know which type is being used.

multitank system

single

brine refill flow

0.45 gpm

resin volume

1.00 cu/ft

units

us inch

prerinse mode

off

rinse if no flow

>for 24 hours

rinse for

>5 minutes

Select either SINGLE tank or PROGRESSIVE. Selecting PROGRESSIVE implies a multi-tank system. Please refer to page 41 for details on setting up a multi-tank system.

THIS CAN BE IGNORED FOR COMMERCIAL APPLICATIONS.

Enter the volume of resin in the tank. This information can be found in the product’s installation manual on the specifications page. Enter in the units shown. For US-INCH, enter the value in

cubic feet.

Select either US INCH or METRIC units. This will change the units when entering programming values such as resin volume and flow rates. If you change this to METRIC, please review your

input for accuracy.

Set this to ON or OFF. This setting will tell the unit to rinse to drain at the time intervals and duration set.

IF PRERINSE MODE IS SET TO ON

Select a prerinse time value from 1 to 240 hours. This tells the unit to rinse to drain if no flow is detected for this duration.

Select the number of minutes the unit should rinse to drain when the NO FLOW duration has passed.

This concludes the Advanced System Set-Up Menu. Continue to press the X key to return to the Main Menu.

29 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 33

Customizing the Setup

Regeneration Set-up

• Press the UP „ or DOWN ‰ arrow to scroll to menu item

• Press the CHECKMARK P key to select a menu item

• Press the UP „ or DOWN ‰ arrow to change a selection

• Press the CHECKMARK P key to save your selection

Default Values are shown for each selection

system ok

7:32 am 2-1-08

> 5) Adv Setup

> 2) regen Setup

salt dosage

9.0 lbs

reserve capacity

30%

Time of regen

2:00 AM

regen mode

delayed

Scroll to ADV SETUP and select

Select REGEN SETUP

This value is the salt dosage in pounds (LBS) for US INCH (total number of pounds of salt used per regeneration). The salt dosage contributes to calculating the resin capacity and is also used when a Smart Brine Tank Sensor is installed to help calculate salt usage and salt remaining. The higher the salt dosage the higher the capacity. Refer to the appendix of the unit’s installation manual for information on setting the salt dosage. For example, for a CSM 300-2 (10 ft³ of resin), and a desired capacity of 250,000 grains, the chart in the manual shows the dosage at 102 pounds.

This setting is generally used for a single-delay system. For a multi-tank system, reserve capacity is not necessary and should be set to zero (0). If you do not change this value in a multi-tank system, your unit will regenerate when 30% of the capacity remains.

This setting is used for time clock regeneration. This is the time of day that the unit will regenerate when needed.

Select either DELAYED or IMMEDIATE. For multi-tank systems, this is normally set to

IMMEDIATE. If immediate is selected, be sure to change the Reserve Capacity setting.

Regen lockout

for 0 hours

This concludes the Regeneration Set-Up section. Continue to press the X key until reaching the Main Menu.

Use this setting to prevent back-to-back regenerations on multi-tank systems, if necessary. When one unit is done regenerating, the next regeneration cannot begin until the set amount of time has passed.

Customizing the Setup 30

Page 34

Customizing the Setup

Cycle Times

• Press the UP „ or DOWN ‰ arrow to scroll to menu item

• Press the CHECKMARK P key to select a menu item

• Press the UP „ or DOWN ‰ arrow to change a selection

• Press the CHECKMARK P key to save your selection

Default Values are shown for each selection

system ok

7:32 am 2-1-08

> 5) Adv Setup

> 3) cycle times

cycle times

>use defaults

backwash time

10 minutes

brine draw-rinse

71 minutes

fast rinse

7 minutes

Scroll to ADV SETUP and select

Select CYCLE TIMES

Select either USE DEFAULTS or CUSTOM. When USE DEFAULTS is selected, the program calculates the cycle times based on hardness and resin volume. When CUSTOM is selected, you can set custom cycle times.

Use this setting to adjust the number of minutes for backwash. You generally will not need to change this setting.

For commercial applications, this value can normally be set to 60 minutes. It can be extended if you find the brine is not being rinsed out properly within this time.

This value is calculated for household units. For commercial units, you should adjust this value to 10 minutes, but it is not required.

fill Time

7 minutes

This will only show if you have selected a 5-cycle valve. This is the refill time. This value can be found in the unit’s installation manual. For example, if you have a Hi-Flo 22 WS90 water softener (3 ft³) and you want to set a capacity of 60,000 grains, then using the chart in Appendix A of the Hi-Flo 22 manual show a time setting of 12 minutes.

For a 4-cycle valve, the refill is controlled by AUX OUTPUT 2 and the refill time is set there. See page 46.

This concludes the Cycle Times section. Continue to press the X key to return to the Main Menu.

31 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 35

Customizing the Setup

Regeneration Triggers

• Press the UP „ or DOWN ‰ arrow to scroll to menu item

• Press the CHECKMARK P key to select a menu item

• Press the UP „ or DOWN ‰ arrow to change a selection

• Press the CHECKMARK P key to save your selection

Default Values are shown for each selection

system ok

7:32 am 2-1-08

> 5) Adv Setup

> 4) Regen Trigger

flow meter

can trigger

Aqua sensor

can trigger

regen intervals

number of days: 0

predict mode

off

Scroll to ADV SETUP and select

Select REGEN TRIGGER

This setting requires an optional flow meter (except Hi-Flo 22) or optional Aqua-Sensor. Use this setting to tell the controller whether the optional flow meter or Aqua-Sensor is used to trigger a regeneration. If set to CAN TRIGGER, the flow meter is used to count the gallons of soft water until the batch value is reached, at which time a regeneration is triggered. You can install water meter and use it just to monitor flow rate and total usage, and not use it to trigger the regeneration. An Aqua-Sensor device (softeners) or differential pressure switch (filters) can be used to trigger the regeneration. You can have both the water meter and Aqua-Sensor/differential pressure installed and able to trigger regeneration. Either one can trigger the regeneration and everything is reset when regeneration is complete.

Use this setting if using time clock regeneration only or if you would like to have a time clock backup for the installed trigger device. It is common to set this at 3 days, although not necessary.

The Predict Mode is used in the flow meter mode to determine the optimum regeneration point. Before the regeneration starts, the control will compare the remaining capacity value with the average daily water use. If the average daily water usage is less than the remaining capacity, the controller will wait 24 more hours be3fore regeneration. If the remaining capacity is less than the average daily water usage, the control will initiate regeneration. This works in delay mode only. At any time, if the total capacity value is reached, the control will initiate an immediate regeneration.

regeneration on monday

>off

Use this setting to select the days of the week to regenerate. This is most useful when running the system as time clock only. For commercial multi-tank systems, leave all days to OFF.

regeneration on monday, ...

>off

The program will go through the rest of the days of the week to set regeneration on or off.

This concludes the Regeneration Trigger section. Continue to press the X key to return to the Main Menu.

Customizing the Setup 32

Page 36

Installation of Accessories

Installation of the Aqua-Sensor Probe

After installing the Aqua-Sensor kit 01008779 - CSM, Hi-Flo 50 or the 01018959 - Hi-Flo 22, it is necessary to configure some settings.

The Aqua-Sensor probe should be installed prior to loading the resin in the tank. Run the probe lead through the opening in the top of the tank. Systems with fiberglass tanks will have a tank plug on the cord. Systems with steel tanks require a 3/4” x 1/2” reducing bushing (included in kit) for the cord grip. Run the probe through the bushing prior to inserting into tank. Use a supplied strain relief to run the connector into the controller. Plug the connector into the circuit board at the position labeled Aqua-Sensor. Figure 23.

system ok

7:32 am 2-1-08

> 4) accessories

> 1) aqua sensor

aqua sensor

>installed

From the home screen, press the DOWN arrow to ACCESSORIES. Press the CHECK

MARK button.

From the ACCESSORIES screen, press the CHECK MARK button at AQUA SENSOR.

Press the CHECK MARK button to change AQUA SENSOR setting. Press the UP or

DOWN arrow to change from NOT INSTALLED to INSTALLED. Press the CHECK MARK when the correct AQUA SENSOR mode is displayed.

Figure 23

Connect Aqua-Sensor connector here at lower right corner of circuit board

Beeper Mode

system ok

7:32 am 2-1-08

> 4) accessories

> 2) beeper

beeper mode

>always off

displayed.

Always ON Always Always

Always OFF Never Never

12 hour mode Never Between 8AM-8PM

24 hour mode Never Always

From the home screen, press the DOWN arrow to ACCESSORIES. Press the CHECK

MARK button.

Press the DOWN arrow button to scroll to BEEPER. Press the CHECK MARK button at

BEEPER.

Press the CHECK MARK button to change BEEPER MODE setting. Press the UP or

DOWN arrow to change from ALWAYS OFF, ALWAYS ON, 12 HR WARNINGS OR 24 HR WARNINGS. Press the CHECK MARK when the correct BEEPER MODE is

key Press Beeps Beeps on Alarm

33 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 37

Installation of Accessories

Installing the Smart Brine Tank (SBT Probe) in to the Brine Tank

1. Place the smart brine probe on top of the brine plate as shown in Figure 24 .

2. Loop the two zip ties thru the holes in the probe housing and loop the zip ties around the outside of the brine well as shown

in Figure 25. IMPORTANT! Tighten zip ties securely to prevent movement.

3. Use zip tie to snug the top of the brine tank probe against the top of the brine well.

4. Route the smart brine tank probe cable to an appropriate opening in the valve control housing. Use the strain-relief plug provided with the SBT probe for installation.

5. Plug the SBT probe connector into the circuit board at the position labeled “Brine Tank” - Figure 26.

Figure 24 Figure 25 Figure 26

Installation of the Smart Brine Tank (SBT) Probe

After the Smart Brine Tank Probe is installed, it is necessary to configure some settings.

system ok

7:32 am 2-1-08

> 4) accessories

> 5) sbt sensor

sbt sensor

>installed

brine tank area

>500 sq/in

18 x 38 Brine Tank - 250 sq in 39 x 48 Brine Tank - 1190 sq in 24 x 40 Brine Tank - 450 sq in 42 x 48 Brine Tank - 1380 sq in 24 x 50 Brine Tank - 450 sq in 30 x 50 Brine Tank - 700 sq in

From the home screen, press the DOWN arrow to ACCESSORIES. Press the CHECK

MARK button.

Press the DOWN arrow key to scroll to SBT SENSOR. Press the CHECK MARK button at

SBT SENSOR.

Press the CHECK MARK button to change SBT SENSOR setting. Press the UP or DOWN arrow to change from NOT INSTALLED to INSTALLED. Press the CHECK MARK when the correct SBT SENSOR mode is displayed.

Press the CHECK MARK button to set BRINE TANK AREA setting. Press the UP or

DOWN arrow to change AREA SQ/IN. See chart below for correct BRINE TANK AREA:

Press the CHECK MARK when the correct BRINE TANK AREA is displayed.

salt geometry

>pellet

Press the CHECK MARK button to change SALT GEOMETRY setting. Press the UP or

DOWN arrow to change from PELLET, ROCK OR BRICK. Press the CHECK MARK

when the correct SALT GEOMETRY is displayed.

Installation of Accessories 34

Page 38

Installation of Accessories

Installing the Wireless Remote

Select a location for the wireless remote monitor (Figure 27). The location must be near an electrical outlet. If a modem is

to be used in the remote, then the location should also be near a standard RJ-11 type telephone wall jack.

Use the “Hole Drilling Template” as a guide to drilling two holes to mount the remote monitor. If drilling into wall board,

drill two 5/16” dia holes and insert the plastic drywall anchors into the holes securing them with the two #10 screws provided. If drilling into a solid surface, drill two 7/32” holes into the surface and screw the two #10 screws into the holes. In either case, leave a gap of approximately 3/32” between the head of the screw and the wall.

Caution! Do not touch any surfaces of the circuit board. Electrical static discharges may cause damage to the board. Handle the circuit board by holding only the edges of the circuit board. Keep replacement boards in their special anti-static bags until ready for use. Mishandling of the circuit board will void the warranty.

(Optional) If a modem is to be installed into the remote monitor, refer to page 37 for installation and setup.

Connect the power cord to the bottom of the remote monitor. If a modem is to be used in the remote, plug a standard

telephone extension cord into the bottom of the remote monitor.

Hang the remote monitor on the two screws.

Disconnect power to the softener. Open the control and connect the RF board into the controller circuit board. Make sure

the RF board is fully seated into all of the sockets (Figure 28). Reconnect power.

Install RF board into unit controller. Line up pins in RF board and press firmly into black connectors. Note orientation of RF

board (Figure 28).

Follow the directions on the next page to program BOTH the main and remote monitor units to communicate with each

other. If modem has been installed in the remote, it is also necessary to follow the directions in the next section of this manual to configure the main controller to use the modem in the remote.

5 3/8”

SCREWS

Figure 27a

MODEM CONNECTION

POWER CONNECTION

Figure 27b

Back of GBE Board

RF Board (Note orientation)

Figure 28

35 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 39

Control Valve Set-up

system ok

7:32 am 2-1-08

Installation of Accessories

> 4) accessories

> 6) wireless rem

remote display

>installed

channel #

rf frequency

>915 mhz

From the home screen, press the DOWN arrow to ACCESSORIES. Press the CHECK MARK button.

Press the DOWN arrow to scroll to WIRELESS REM.

Press the CHECK MARK button to change REMOTE DISPLAY setting. Press the UP or DOWN arrow to change from NOT INSTALLED to INSTALLED. Press the CHECK MARK when the correct REMOTE DISPLAY mode is displayed.

Press the CHECK MARK button to change CHANNEL # setting. Press the UP or DOWN arrow to change CHANNEL #. Press the CHECK MARK when the correct CHANNEL# is displayed.

NOTE: The CHANNEL # for the control valve must be the same as the CHANNEL # for the Remote Display.

NOTE: Do not change RF FREQUENCY for North American installations.

Wireless Remote Set-up

system ok

7:32 am 2-1-08

> 4) setup

> 1) RF SETUP

channel #

rf frequency

>915 mhz

Continue to press X to return to Home Screen.

From the home screen, press the DOWN arrow to SETUP. Press the CHECK MARK button.

From the SETUP screen, press the CHECK MARK button at RF SETUP.

Press the CHECK MARK button to change CHANNEL # setting. Press the UP or DOWN arrow to change CHANNEL #. Press the CHECK MARK when the correct CHANNEL# is displayed.

NOTE: The CHANNEL # for the control valve must be the same as the CHANNEL # for the Remote Display.

NOTE: Do not change RF FREQUENCY for North American installations.

Installation of Accessories 36

Page 40

Installation of Accessories

Check Signal Strength

Check the signal strength once the control valve and wireless remote are setup. On the Softener Controller, go to the Main Menu/Advanced setup/Diagnostics/Test Wireless to check signal strength. The signal strength indicator (SSI) will show a value of between 0 and 8. If the SSI is at least 4, then the installation is complete. It the SSI drops below 4, then it may be necessary to select an alternate location for the wireless remote.

system ok

7:32 am 2-1-08

> 5) adv setup

> 5) diagnostics

> 3) test wireless

wireless test

230/230 rssi=8

From the home screen, press the DOWN arrow to ADV SETUP. Press the CHECK MARK button.

Press the DOWN arrow to scroll to DIAGNOSTICS.

Press the DOWN arrow to scroll to TEST WIRELESS.

From the TEST WIRELESS screen, press the CHECK MARK button to test.

Installing the Modem (optional)

Note: The modem can be installed into either the back of the main controller or the back of the remote control board. The functionality of the modem is the same in either installation with the important exception that automatic firmware updating is ONLY available on units which have the modem installed on the main controller.

Before installing the modem into the back of the GBE board or the back of the remote, the GBE circuit board or the

1. remote must first be powered off.

When handling all circuit boards, take care to only touch the edges of the circuit boards – not the metal pins. The

2. electronics on all circuit boards can be damaged by static electricity.

Make sure all of the pins at all four connectors are aligned between the modem board and the main controller board.

3. Make sure that the modem board is fully seated into all four sockets.

When all connections have been made restore power.

37 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 41

Installation of Accessories

Installing in GBE Board

Open the controller cover and locate the modem connection on the back of the board (see figure 29). Insert line modem board (P/N 01020307) into the socket on the back of the board. Make sure that all of the pins in all four connectors are aligned and make sure the modem is fully seated into all of the sockets.

Figure 29

Modem Board

Back of GBE Board

Installing in Remote

Open the remote monitor housing by removing the two screws and squeezing the sides of the monitor housing slightly. Insert the modem board (P/N 01020307) into the socket on the back of the remote board (Figure 30). Make sure that all of the pins in all four connectors are aligned and make sure the modem is fully seated into all of the sockets. Snap the two halves of the

remote housing back together using light finger pressure and insert the two screws.

Figure 30

Modem Board

Back of Remote Circuit Board

Modem Setup - GBE

system ok

7:32 am 2-1-08

Installation of Accessories 38

Page 42

Installation of Accessories

> 4) accessories

MARK button.

From the home screen, press the DOWN arrow to ACCESSORIES. Press the CHECK

> 7) Modem

Telephone modem

>installed

Press the DOWN arrow to scroll to MODEM.

If necessary, press the CHECK MARK button to change TELEPHONE MODEM setting. Press the UP or DOWN arrow to change from NOT INSTALLED to INSTALLED. Press the CHECK MARK when the correct TELEPHONE MODEM mode is displayed.

If necessary, press the CHECK MARK button to change MODEM LOCATION

Modem location

>in main control

Call frequency

>every 10 regens

setting. Press the UP or DOWN arrow to select IN MAIN CONTROL VALVE or IN REMOTE. Press the CHECK MARK when the correct MODEM LOCATION is

displayed.

If necessary, press the CHECK MARK button to change CALL FREQUENCY setting. Press the UP or DOWN arrow to increase or decrease CALL FREQUENCY. Press the CHECK MARK when the desired CALL FREQUENCY is displayed.

The default value of EVERY 10 REGENS can be changed from 1 to 99 successful regenerations. If set to 1, the unit will call in the following morning after each regeneration. The interval can also be set to 0, meaning the unit would NEVER call in, unless there was a problem detected. It is recommended for a typical installation the default value of EVERY 10 REGENS is used.

time zone

Press the CHECK MARK button to change TIME ZONE setting. Press the UP or DOWN arrow to increase or decrease TIME ZONE. Press the CHECK MARK when

>00:00

the correct TIME ZONE is displayed.

When using a modem, the control will occasionally access the internet to synchronize the date and time. In order to do this correctly, the control must be told which time zone it is installed in. The time zone is specified as so many hours ahead or behind GMT time. The “GMT offset” for some common cities are listed below:

GMT Offset

New York -5:00 (and anywhere in EST)

Chicago -6:00 (CST)

Denver -7:00 (MST)

Los Angeles -8:00 (PST)

London 0:00

Paris 0:00

Rome +1:00

39 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 43

Installation of Accessories

dealer id

>00000

Press the CHECK MARK button to change DEALER ID setting. Press the UP or DOWN arrow to increase or decrease each digit of the DEALER ID. Press the CHECK MARK to move to the next digit. Press the CHECK MARK when the correct DEALER ID is displayed. The dealer ID is your dealership’s account number. Enter with

leading zeroes, if necessary.

data phone #

Press the CHECK MARK button to change DATA PHONE # setting. Press the UP or DOWN arrow to increase or decrease each digit of the DATA PHONE #. Press the

>18884137028

CHECK MARK to move to the next digit. Press the CHECK MARK when the correct DATA PHONE # is displayed. Use a local number whenever possible.

It is necessary to provide a telephone number to be called by the unit. Typically, it is desired that the unit call a local access number. These local access numbers, for nearly every area code around the globe, can be found from the www.myculligan.com website at http://www.myculligan.com/technical/tech_ref-gbe-boards.asp. The unit can also be programmed with the default toll-free access number. Use a local number whenever possible.

Test Modem

This menu attempts to send in a “test message”. The screen indicates whether or not this process is successful. Sending a “test message” will also update the time and date on the GBE controller to the correct time. If the modem is installed on the main controller (as opposed to installed in the remote control) then this testing process will also check to see if there is an updated version of firmware available on the Culligan servers.

After conducting a phone line test, it is important to verify that the new time and date settings on the controller are correct. If the new time setting has the incorrect value for the “hours” it is likely that the time zone setting on the control is incorrect. The time zone setting is found under the Main

Menu / Accessories / Modem screen and is displayed in the format of GMT +/- X hours. (See the section of this manual called “Installing the modem”

system ok

7:32 am 2-1-08

> 5) adv setup

> 5) diagnostics

> 5) test phoneline

modem test

emailing now please wait...

From the home screen, press the DOWN arrow to ADV SETUP. Press the CHECK MARK button.

Press the DOWN arrow to scroll to DIAGNOSTICS.

Press the DOWN arrow to scroll to TEST PHONELINE.

From the TEST PHONELINE screen, press the CHECK MARK button to TEST.

Installation of Accessories 40

Page 44

Installation of Accessories

modem email

success

modem test time

set success

modem test

checking for new fw

modem test

no new fw

POSSIBLE RESULTS

CONNECTING AN EXTERNAL FLOW METER

Most metered commercial units require an external flow meter device. this requires an entry in the programming for the meter chosen. The entry is the pulses per gallon, or K Factor. Refer to the table on the page 63 for meter K Factors.

> 4) Accessories

> 9) Flow Meter

From the home screen, press the DOWN arrow to ACCESSORIES. Press the CHECK MARK button.

Press the DOWN arrow key to scroll to FLOW METER and press the CHECK MARK button.

Flow Meter

To change the value, press the CHECK MARK button and then use the UP ARROW or DOWN ARROW keys. Press the CHECK MARK button when done. Note: Hi-Flo 22 is

80.0 Puls/Gal

to be set at 78 puls/Gal.

Press the X key until you return to the main screen.

SETTING UP A MULTI-TANK SYSTEM

A Multi-tank system requires additional programming.

REMINDER: Any additional program changes such as REGEN SETUP, CYCLE TIMES and REGEN TRIGGER must be programmed into each control in the system.

system ok

7:32 am 2-1-08

> 5) adv setup

> 1) system setup

From the home screen, press the DOWN arrow to ACCESSORIES. Press the CHECK MARK button.

Press the DOWN arrow key to scroll to SYSTEM SETUP and press the CHECK MARK button.

41 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 45

Installation of Accessories

multitank system

progressive

prog Flow trip

210 GPM

This setting establishes a flow rate which, when attained, will cause another unit to come on-line until the total flow rate is less than the established trip point for 30 seconds. Should the flow demand exceed the trip point by a rate equal to or greater than two times the trip point, another unit shall be brought on-line (assuming the system has more than two units in total). Each subsequent equivalent increase in flow demand shall continue to bring additional units on line (up to six total units if the flow demand is six times the TRIP amount). Units shall be returned to a stand-by mode in the reverse order as the system flow decreases by a rate equal to or greater than the trip point. Generally, the trip point is the rated continuous flow rate of one unit. These values can be found in the unit’s instruction manual.

NOTE: ALTERNATING OPERATION: To set up the GBE for alternating operation (one on, the rest standby), set the trip point to 999. It is unlikely that the system will reach 999 gallons per minute to bring on an additional unit.

progress flow master

Scroll through the settings until you see MultiTank System. Press the CHECK MARK button and then use the UP ARROW or DOWN ARROW key to change from

SINGLE to PROGRESSIVE flow. Press the CHECK MARK button when done.

NOTE: all multi tank systems are to be set to PROGRESSIVE. See below on adjust-

ments needed for alternating or parellel operation.

Press the CHECK MARK button and then use the UP or DOWN arrow keys to set the progressive flow trip point. Press the CHECK MARK button when done.

In a multi-tank system, one unit must be specified as master. All other units are slaves. For example, in a triplex system, select one unit to be the master and set this setting to MASTER. In the 2nd unit, set this to SLAVE 1. In unit 3, set it to SLAVE 2. You can have up to 5 slaves connected to a master.

NOTE: PARALLEL OPERATION: To set up the GBE for parallel operation (all online), set the trip point to zero (0). As long as the flow is above zero, all units will stay online. You must also set the jumpers as explained on page 12 for progressive flow.

Flow meters are required for progressive flow – one for each unit. See page 14 to set up the meters.

Continue pressing the down key to cycle through the rest of the options (refer to page 29). At the System Setup screen press the “X” key to return to the main screen.

NOTE: You must repeat this programming on all other units in the system. On slave units the PROG FLOW TRIP can be IGNORED; the only trip point recognized is the one set on the master unit.

Brine Reclaim

For brine reclaim, AUX OUT 2 and AUX OUT 3 must be set to open and close the valves to direct the brine. There are 4 things to set for each aux output.

1 – Cycle Type (AUX X CYCLE TYPE) – can be set to NORMALLY ON or NORMALLY OFF. For brine

reclaim, set it to NORMALLY OFF.

2 – Cycle Position (AUX OUT X) – Any cycle position can be selected here. For brine reclaim, we want the

BRINEDRAW POS.

3 – Delay (AUX OUT DELAY) – This is the delay before the OUTPUT is “activated” in minutes. For brine reclaim

we want delay on AUX 3 and no delay on AUX 2.

4 – On time (AUX OUT ON) – This is the number of minutes the OUTPUT is “activated” in minutes. For brine

reclaim, cycle type is NORMALLY OFF so this is the amount of time the Aux contact is on.

Installation of Accessories 42

Page 46

Installation of Accessories

Refer to page 46 for more information on the operation of the Aux Outputs. Refer to the instructions below for step by step setting of these values.

• Press the UP „ or DOWN ‰ arrow to scroll to menu item

• Press the CHECKMARK P key to select a menu item

• Press the UP „ or DOWN ‰ arrow to change a selection

• Press the CHECKMARK P key to save your selection

Default Values are shown for each selection

system ok

7:32 am 2-1-08

> 4) accessories

> 4) aux outputs

> 2) aux out 2

3) aux out 3

aux2 cycle type

normally off

aux out 2

service pos

aux2 out

delay 0 mins

aux2 out

on 0 mins

Scroll to ACCESSORIES and select

Select AUX OUTPUTS

Select AUX OUT 2

Can be set to NORMALLY OFF or NORMALLY ON. For brine reclaim, set to NORMALLY OFF.

This can be set to any cycle. For brine reclaim, change this to BRINEDRAW POS.

This is the activation delay. For brine reclaim, leave at zero (0).

Set this value to the number of minutes needed for aux 2 to be activated. Refer to the brine reclaim manual, 01018946, for recommended settings.

Now set AUX OUT 3

2) aux out 2

> 3) aux out 3

aux3 cycle type

normally off

aux out 3

service pos

43 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Select AUX OUT 3

Can be set to NORMALLY OFF or NORMALLY ON. For brine reclaim, set to NORMALLY OFF.

This can be set to any cycle. For brine reclaim, change this to BRINEDRAW POS.

Page 47

Installation of Accessories

aux3 out

delay 0 mins

aux3 out

on 0 mins

This is the activation delay. For brine reclaim, set this to the same value that AUX2 OUT is set to be ON (last setting on AUX2). This allows AUX3 to turn on immediately after AUX2 turns off.

Set this value to the number of minutes needed for aux 3 to be activated. Refer to the brine reclaim manual, 01018946, for recommended settings.

This concludes setting the AUX OUT values for Brine Reclaim. Press the X key until you return to the Main Menu.

SERVICE PHONE NUMBER

If the Modem is not installed it is possible, in addition to displaying the error message, to display a message that reads “Call Culligan at: XXXXXXXXXX” where the telephone number XXXXXXXXXX can be programmed by the dealership (typically programmed to be the telephone number of the dealership). This number is programmed under the menu: Main Menu / Accessories / Service Phone.

system ok

7:32 am 2-1-08

> 4) accessories

From the home screen, press the DOWN arrow to ACCESSORIES. Press the CHECK MARK button.

> 10) service phone

service phone #

button at SERVICE PHONE.

Press the CHECK MARK button to change SERVICE PHONE # setting. Press the UP or DOWN arrow to increase or decrease each digit of the SERVICE PHONE #. Press the CHECK MARK to move to the next digit. Press the CHECK MARK when the correct SERVICE PHONE # is displayed.

EXTERNAL FILTER

The unit can provide alarm feedback for a sediment or carbon filter installed upstream of the unit. The Auxiliary flow alarm can be used to monitor the flow through this filter.

To use this feature it is necessary to specify the total lifetime totalized flow of the auxiliary filter in either gallons or liters at Main Menu/Accessories/Down Once set, it will begin to track the total gallons through the system flow

meter. Once the total flow reaches the specified lifetime totalized flow, the system will display the error

message “Change Auxiliary Filter” on the main display as well as the remote display and via the telephone modem if these secondary devices are used.

Press the DOWN arrow to scroll to SERVICE PHONE. Press the CHECK MARK

system ok

7:32 am 2-1-08

Note: Once the auxiliary filter has been replaced, the auxiliary filter alarm must be reset by returning to the same menu: Main Menu / Accessories / Auxiliary Flow Alarm.

Installation of Accessories 44

Page 48

Installation of Accessories

From the home screen, press the DOWN arrow to ACCESSORIES. Press the CHECK

> 4) accessories

MARK button.

> 11) ext. filter

external filter alarm

>installed

filter capacity

>10000 gallons

From the ACCESSORIES screen, press the CHECK MARK button at EXT. FILTER.

Press the CHECK MARK button to change EXTERNAL FILTER ALARM setting. Press the UP or DOWN arrow to change from INSTALLED to NOT INSTALLED. Press the CHECK MARK when the correct EXTERNAL FILTER ALARM mode is displayed.

Press the CHECK MARK button to change FILTER CAPACITY setting. Press the UP or DOWN arrow to increase or decrease FILTER CAPACITY. Press the CHECK MARK

when the correct FILTER CAPACITY is displayed.

45 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 49

Delay Minutes

On Minutes

Service

Backwash Brine Draw

Auxiliary Contacts

Auxiliary Board

The auxiliary board comes installed in all commercial equipment. It can control up to four, 24 VAC outputs (max current 2.1 amps output). Aux Output 1 is used to power the 24 VAC drive motor found on all valves. When Aux Output 1 is used for this, then Aux Output 4 is automatically configured to operate a solenoid which can be used for a standby or blocking. Aux Output 4 is powered during all cycles except service, and unpowered during service.

Figure 31

Auxiliary Input

For CSM and Hi-Flo 50 softeners, Aux Output 2 is used to power the refill solenoid. The Aux Output 2 “On” time needs to be set based on the desired salt dosage/capacity as found in the appendix of the unit’s installation manual. See the Aux Output 2 settings for a detailed example.

Each Aux Output has the following settings:

• Cycle Type (AUX X CYCLE TYPE) – Can be set to NORMALLY ON, NORMALLY OFF or REPEAT CYCLE. This means the Output can always be on or always be off until it reaches the chosen cycle position. REPEAT CYCLE allows the output to turn on and off at a set interval during the cycle chosen.

• Cycle Position (AUX OUT X) – Any cycle position can be selected here. This is the cycle position that the AUX OUT is “activated” (turned on or off).

• Delay (AUXX OUT DELAY) – This is the delay before “activating”. You can have the AUX OUT activation delayed a specified number of minutes into the cycle.

• On time (AUXX OUT ON) – This is the number of minutes the AUX OUTPUT is “activated” in minutes. After the specified number of minutes, the OUTPUT is deactivated.

• Off Time (available only when Repeat Cycle is selected for Cycle Type) – This is the number of minutes of Off time during the chosen cycle. The aux output will cycle on and off during the selected cycle.

For example, the chart below shows how the timing would work if the CYCLE TYPE was set to NORMALLY OFF, the CYCLE POSITION was set to BACKWASH, the DELAY minutes greater than zero, and ON minutes greater than zero.

Auxiliary Outputs

Figure 32

Auxiliary Contacts 46

Page 50

Auxiliary Contacts

Aux Output 2 Example

As mentioned above, for CSM and Hi-Flo 50 softeners, this output is used for the refill solenoid. As an example, let’s say we have a CSM-300-2 and we need to set this up for refill minutes. We are looking for a capacity around 250,000 grains (10 lbs/ft³).

According to the chart on page 92 of the CSM installation manual (01016370), we are looking at a salt dosage of 10.2 lbs/ft³ and need to set the ON minutes of AUX2 to 17.

system ok

7:32 am 2-1-08

> 4) accessories

> 4) aux outputs

> 2) aux out 2

3) aux out 3

aux2 cycle type

normally off

aux out 2

service pos

aux2 out

delay 0 mins

Here is how to set this up:

Scroll to ACCESSORIES and select

Scroll to AUX OUTPUTS and select

Scroll to AUX OUT 2 and select

Leave this set at NORMALLY OFF. We want the output to energize (turn on) the refill solenoid

This should be set to SERVICE POS.

No delay is necessary.

aux2 out

on 0 mins

For our example, this would be set to 17.

AUX OUTPUT 3 has the same menu options. Refer to the chart on page 48 for quick reference.

47 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 51

Auxiliary Contacts

system ok

7:32 am 2-1-08

> 4) Accessories

> 3) aux in

4) aux outputs

> 2) aux out#2

3) aux out#3

To use the auxiliary contacts, some configuration settings must be changed.

From the home screen, press the DOWN arrow to ACCESSORIES. Press the CHECK MARK button.

Press the DOWN arrow key to scroll to AUX IN.

(1)

1) aux input

> 6 seconds

AUX OUT 2 and AUX OUT 3 menu selection are the same.

aux 2 Cycle type

> normally off

aux out 2

> service

aux2 out

delay > 0 minutes

aux2 out

on > o Minutes

(“NORMALLY ON” Type) (“REPEAT CYCLE” Type)

aux 2 cycle type

> normally on

aux out 2

> service

aux2 out

delay > 0 minutes

aux2 out

off > o Minutes

aux 2 cycle type

> rep eat cycle

aux out 2

> service

aux2 out

gallons > 0

aux2 out

on 0 minutes

aux2 out

off 0 minutes

Auxiliary Contacts 48

Page 52

Manual Regeneration

Follow the procedure below to initiate a manual regeneration at the control valve or the remote display.

system ok

12:00 am 1-1-08

1) information

> 2) manual mode

3) set date/time

4) Accessories

Press DOWN arrow. Scroll to MANUAL MODE.

Press the CHECK MARK button to select.

Manual Mode

>Regen off

The “REGEN OFF” value is the default setting.

Press the CHECK MARK button to change manual mode setting. Use the UP or DOWN arrow to change the setting. Once the desired value is displayed, this value can be accepted by pressing the “CHECK MARK” button.

Manual Mode

Regen tonite

By selecting the “REGEN TONITE” value the softener will regenerate that night at 2:00 AM (or at the preset regeneration time)

Manual Mode

By selecting the “REGEN NOW” value the softener will begin regeneration immediately.

Regen now

NOTE: In multi-tank systems, the regeration request is sent to the master control and it will allow the unit to regerate at the next availble time.

Press the “CANCEL” button to return to the “home” screen.

49 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 53

Manual Cycling

Manual cycling can be performed when the unit is starting either in SERVICE or while it is already within any portion of the REGENERATION process. If the unit is currently regenerating, the name of the current cycle position and the number of minutes remaining in the current cycle position will be displayed.

system ok

7:32 am 2-1-08

> 5) adv setup

From the home screen, press the DOWN arrow to ADV. SETUP. Press the CHECK MARK button.

> 5) diagnostics

Press the DOWN button to scroll to DIAGNOSTICS. Press the CHECK MARK button at DIAGNOSTICS.

> 5) motor control

Press the DOWN button to scroll to MOTOR CONTROL. Press the CHECK MARK button at MOTOR CONTROL.

If control is not in regeneration, this is shown.

motor at pos s

up: forward

Menu Status

MOTOR AT POS S Motor at service position MOTOR AT POS B Motor at backwash position MOTOR AT POS E Motor at brine draw/slow rinse position MOTOR AT POS F Motor at fast rinse/refill position

To cycle the control valve without stopping press the CHECK button. To stop the motor at the end of each cycle press the UP arrow.

If cycling the control during regeneration, this screen is shown after MOTOR CONTROL.

backwash minutes left: 8

>next cycle

Press the CHECK MARK button to change REGENERATION setting. Press the UP or DOWN arrow to move to NEXT CYCLE, END REGEN NOW or END/CAN- CEL TRIG. Press the CHECK MARK when the correct REGENERATION setting is displayed.

Manual Cycling 50

Page 54

Information

The following information can be displayed at the control valve or remote display.

system ok

12:00 am 1-1-08

Press DOWN arrow

> 1) information

2) manual mode

3) set date/time

4) Accessories

Pressing the CHECK MARK button will change the display to show a “>” symbol next to the displayed value.

Press DOWN arrow to scroll through the “INFORMATION” menu.

salt tank level

Displays salt level and approximate number of days of salt remaining. This screen will only be displayed if a Smart Brine Sensor is connected.

Press DOWN arrow to view next screen.

approx 12 days

salt remaining

remain capacity

80%

remain capacity

870 gallons

current flowrate

0.0 GPM

next regen on

1/8

today’s usage

115 gallons

Displays approximate number of days of salt remaining. This screen will only be displayed if a Smart Brine Tank Sensor is installed.

Press DOWN arrow to view next screen.

Displays the percent softening capacity remaining.

Press DOWN arrow to view next screen.

Displays the remaining softening capacity in gallons.

Press DOWN arrow to view next screen.

Displays the current flow rate.

Press DOWN arrow to view next screen.

Displays the date when the next regeneration will occur (based on average daily water usage).

Press DOWN arrow to view next screen.

Displays today’s water usage.

51 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 55

Information

average daily

275 gallons

Press DOWN arrow to view next screen.

Displays average daily water usage.

Press DOWN arrow to view next screen.

ext filtr cap rem

10,000 gallons

Displays how many gallons remain before the optional filter cartridge needs to be replaced.

Press the “CANCEL” button to return to the “home” screen.

SET DATE/TIME

If the unit loses time for some reason, you can use this setting to reset the correct date and time. Please note that if you have a modem installed and connected to the phone line, the unit will check for the correct time each time it calls in.

To set the date and time:

system ok

7:32 am 2-1-08

> 1) information

> 3) set date/time

set month

set day

set year

clock type

set hour

Scroll to Information and select

Scroll to SET/TIME

Scroll up or down to set month

Scroll up or down to set the date

Scroll up or down to set the year (4-digit)

Choices are 24 HR (00:00 to 23:59) or 12 HR (AM/PM)

Based on choice of CLOCK TYPE, scroll to select the hour

set minutes

daylight savings

Scroll to set minutes

If you observe daylight savings in your area, set to YES.

Press the X key until you return to the Main Menu.

Information 52

Page 56

Error & Alert Codes

When the controller identiﬁes that an error has occurred, it is programmed to take steps to attempt to correct the error on it’s own. If it is unable to correct the problem, the controller will display the message “PROBLEM FOUND”. When an error message is displayed (on either the GBE Controller or the remote display), pressing the “CHECK- MARK” on the keypad will display the detected error condition(s). Some of these messages will also provide additional information to help correct the error.

The following error messages may display on both the GBE controller display as well as the Remote Display (if one is connected:)

If the words “PROBLEM FOUND” appear on the main screen, it indicates that there are one or more errors detected. Pushing the “CHECK MARK” button will display the ﬁrst error present. Pressing the DOWN arrow will show any additional errors present. At the bottom of this list the user can “CLEAR THE ERROR” or “EXIT”. Pressing the “CHECK MARK” button on the “CLEAR THE ERROR” message causes the controller to re-check to see if the error condition still exists, if it still exists, the error will remain displayed on the main screen. If the error no longer exists the main menu will return to displaying “SYSTEM OK”.

Error Description Reason for Error Comment/ Clearing Error Message

POSITION SENSOR ERROR

MOTOR POSITION ERROR

BRINE BLOCKED

REPLACE FILTER MEDIA

REPLACE AUX FILTER MEDIA

CALL CULLIGAN AT XXX-XXX-XXXX

SALT BRIDGING

XX DAYS SALT RE MAINING

AQUA-SENSOR SALT ERROR

NO REMOTE RF SIGNAL

The motor is turning, but the position sensor appears to be incorrect

Motor did not move when it should. No feedback from switches.

The ﬂow rate of brine or water to or from the brine tank is fully or partially blocked

Total gallons thru the unit has exceeded the speciﬁed capacity of the media

Total gallons thru the secondary ﬁlter (i.e. “Big Blue” ﬁlter) has exceeded the speciﬁed capacity of the big blue

This message is displayed if an error has been detected that requires servicing and no modem installed in the system

Brine tank has low concentration of brine Use a tool to break up any salt bridge inside the brine tank

This is a prediction of the number of days until it will be necessary to add salt to the brine tank

Aqua-Sensor did not detect brine during the regeneration cycle

Main board is not receiving a signal from the remote

Check the motor using manual motor control and the position sensors using Main Menu/ Advanced/ Diagnostics Sensors

Use manual motor control to see if motor is actually working and not jammed. Use Diagnostics/ Sensor menu to verify that the optical or mechanical position switches are working

Check brine line for blockages or air leaks. Check eductor and eductor screen for blockages

Replace the media. Reset the media ﬁlter life at Main Menu/ Advanced Setup/Regen Settings/ Media Life

Replace optional ﬁlter cartridge. Reset the aux. Filter media life at Main Menu/ Accessories/ Aux Filter menu

Call the number shown. If possible, place this call using a phone that will allow you to see and enter changes to the main controller if required by the service technician during the call

Salt can be added to the brine tank at any time. It is recommended that the brine tank be ﬁlled to approximately 2/3 full.

Check brine tank - add salt if necessary. Check Z ratio of the AquaSensor at Main Menu/ Advanced / Diagnostics/ Sensors

Remote is off, out of range or on a different channel from the main board. If interference is suspected, try moving the remote closer or switching to a different channel on both the main and remote units

LOW SALT LEVEL

LOW BATTERY

BRINE OVERFILL

NO REFILL

53 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Salt level is low; less than 15 days of salt remaining.

Battery needs replacement. Replace with Panasonic Model# CR 2032 3V battery.

Too much water in brine tank. Plugged drain line ﬂow control (Unit will not draw brine). Slow leak to brine line. Faulty eductor piston Power outage while control was in reﬁll position.

Failure to reﬁll brine tank. Reﬁll restrictor plugged. Air in brine line causes ﬂoat to slam shut.

Contact Culligan dealer for salt deviery or ﬁll brine tank with salt.

Check edorctor; check fro brine draw. Clean drain line ﬂow control. Clean eductor screen and nozzle. Replace ductor piston.

Clean or replace reﬁll restrictor. Verify all tubing connections are properly assembled.

Page 57

Diagnostics

There is a large number of diagnostic menu screens to aid in setup and troubleshooting of the GBE. Below is an overview of the menus.

Advanced Statistics

system ok

7:32 am 2-1-08

> 5) adv setup

> 5) diagnostics

> 1) advanced stat

totalized flow

18203 gallons

current flow rate

5.0 gpm

total regens

regens in last 14 days:

From the home screen, press the DOWN arrow to ADV. SETUP. Press the CHECK MARK button.

Press the DOWN arrow button to scroll to DIAGNOSTICS. Press the CHECK MARK button at DIAGNOSTICS.

From the DIAGNOSTICS screen, press the CHECK MARK button at ADVANCED STAT.

The total number of gallons of soft water since the unit was installed is displayed. Press DOWN arrow to view the next statistic.

The CURRENT FLOW RATE of the unit is displayed. Press DOWN arrow to view the next statistic.

This is the total number of regenerations since the unit was installed Press DOWN arrow to view the next statistic.

This is the number of REGENS IN LAST 14 DAYS of operation. Press DOWN arrow to view the next statistic.

days since last regen:

last regen on:

1/3

last regen trig

flow meter

remaining capacity

613 gallons

total capacity

891 gallons

This is the number of DAYS SINCE LAST REGENERATION of unit. Press DOWN arrow to view the next statistic.

This is the date of last regeneration of unit (January 3). Press DOWN arrow to view the next statistic.

This shows what device triggered the last regeneration. Press DOWN arrow to view the next statistic.

This shows the REMAINING CAPACITY of the unit in gallons. Press DOWN arrow to view the next statistic.

This shows the TOTAL CAPACITY of the unit in gallons. Press DOWN arrow to view the next statistic.

Diagnostics 54

Page 58

Diagnostics

fw110lt01

This shows the latest firmware version of unit. Press DOWN arrow to view the next statistic.

may 9 2008

s/n: 00001078

last power up

01-01-08 12:01 pm

This shows the serial number of circuit board. Press DOWN arrow to view the next statistic.

The date and time showed here is when the unit last was powered up. This can be helpful if there was a power outage to see how long the unit has been on.

Check Sensors - Main Board, Flow meter, and/or Aqua-Sensor.

system ok

7:32 am 2-1-08

> 5) adv setup

> 5) diagnostics

From the home screen, press the DOWN arrow to ADV. SETUP. Press the CHECK MARK button.

Press the DOWN arrow to scroll to DIAGNOSTICS. Press the CHECK MARK button at DIAGNOSTICS.

> 2) check sensors

main board position sensor

home: off Pos: off

Press the DOWN arrow to scroll to CHECK SENSORS. Press the CHECK MARK button at CHECK SENSORS.

MAIN BOARD POSITION: Position of Home & Program switches. Press DOWN arrow to view

the next statistic.

Cycle Home Switch Program Switch

Service Off Off Backwash On On Brine Draw/Slow Rinse On Off Fast rinse/Refill On On

flow meter

7 puls/sec

aquasensor supply voltage

2.5vac: pass

FLOW METER: Current pulses per second. (K-Factor) - refer to page 63 to varify correct reading. Press DOWN arrow to view the next statistic.

AQUASENSOR SUPPLY VOLTAGE: This will be either PASS or FAIL. If this reading is FAIL, check the Aqua-Sensor connection to the circuit board and to the power supply. Press DOWN arrow to view the next statistic.

55 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 59

Diagnostics

aquasensor

zratio 1.075

zminimum 1.070

0.75% increase

AQUASENSOR: Troubleshooting statistics.

Z-Ratio (impedance ratio) - Number calculated by microprocessor on measured voltage

•

values that are converted to a digital representation. This is the value that the control monitors in order to determine need for regeneration and salt rinse-out.

Z-Minimum (minimum impedance ratio) - Reference point that the Z-ratio is

•

compared to, in order to initiate a regeneration. This number is reset after every successful regeneration.

Increase Percent (impedance ratio increase) - During service, this number

• represents the percent increase or z-ratio over z-minimum. A regeneration is initiated when it reaches 7.5% or more for at least 6 minutes.

Press DOWN arrow to view the next statistic.

sbt sensor

salometer=op

salt level=op

fr1=bl fr2=op

SBT SENSOR: Smart Brine Tank Probe troubleshooting statistics.

The SBT probe has four sensors within it. The Check sensor screen displays the current status (opened = “OP”, or blocked =“BL”) for all four sensors. The expected outputs from the SBT probe inside the brine tank are shown in Table 1 below while the expected outputs from an SBT probe “in air” are shown in the Table 2.

Table 1 - Expected Readings on the Sensor/Diagnostic screen when the SBT probe is installed inside the brine tank

displays “BL” displays “OP”

Salometer

Salt Level

Brine at least 1 inch above the salt plate.

Normal Operation .– Salt level greater than 8”

Salt level less than 8” above the salt plate

above the salt plate

Flow Rate #1

Water level in brine tank is below salt plate Water level is brine tank is more than 1”

above salt plate

Flow Rate #2

Water level is brine tank is more than 1” above

Water level in brine tank is below salt plate

salt plate

Table 2 - Expected Readings from the SBT probe when the probe is just sitting in “air” (ie not installed in the brine tank)

Normally Probe Inverted

Salometer

Salt Level

Flow Rate #1

Flow Rate #2

“OP” “BL”

“OP” “OP”

“BL” “OP”

“OP” “BL”

Diagnostics 56

Page 60

Diagnostics

SBT AVG T3: In addition to these four sensors, the SBT probe takes a measurement

sbt avg t3

30 seconds

a new T3 average number. During each subsequent regeneration, the new T3 is compared to the average T3 number. If the new T3 exceeds the average T3 by more than 50% then the system will display a “Brine Line Blockage – Check Brine Line” error message. The average T3 value is displayed on the diagnostic screen after the SBT sensor screen.

sbt last t3

30 seconds

Test Wireless: See page 37.

Test Progressive Flow:

during each regeneration cycle called “T3”. This measurement varies from system to system, but is typically between 10 and 60 seconds for a system. When the SBT is turned from UNINSTALLED to INSTALLED on the Accessories menu, the average value of T3 is erased and the system will use the next three regeneration cycles to compute

Press DOWN arrow to view the next statistic.

SBT LAST T3: Smart Brine Tank Probe troubleshooting statistics. This is the last T3 valve recorded by the probe. Press DOWN arrow to view the next statistic.

system ok

7:32 am 2-1-08

> 5) advanced setup

> 5) Diagnostics

> 4) Test Progressive Flow

Progressive Test

1:0000, 2:0000

3:0000, 4:0000

5:0000, Tx: 0000

Motor Control

Use Data Port

Scroll to ADVANCED SETUP and select

Scroll to DIAGNOSTICS and select

Scroll to TEST PROGRESSIVE FLOW and Select

The progressive test screen will show the data packet transmissions from the Master (Tx) and which slaves are recieving (1,2,3,4 and/or 5). For example, in a triple system, if the transmission from the master (Tx) is 0085, then you should see 1:0085 and 2:0085. 3,4, and 5 will remain all zeros since no other slaves are connected.

See page 50

See Appendix C, page 65

Test phone line

Test wc app

57 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

See page 40

IGNORE THIS

Page 61

Menu Lockout and Menu Default

Menu Lockout

It is possible to lock the keypad of the GBE controller so that users will only have access to the INFORMATION, MANUAL MODE, and SET DATE/TIME menu screens. The system can be locked by pushing the up and down arrow keys simultaneously and holding them down for 10 seconds. Repeating this process will unlock the keypad.

Menu Default

Below is the procedure to default the board to factory settings and begin the FIRST TIME SETUP.

1. Power down the control.

2. Press and hold “UP” and “CANCEL” buttons.

3. Power up the control while continuing to hold “UP” and “CANCEL” buttons. for at least 5 seconds

4. Release “UP” and “CANCEL” buttons. (display should be blank - if not go back to step 1)

5. Power down the control.

6. Power up the control again. You should see the display light up for 2 seconds and then show FIRST TIME SETUP.

7. Follow FIRST TIME SETUP process on page 23.

Menu Lockout and Menu Default 58

Page 62

Menu Overview

Continued on page 61

59 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 63

Menu Overview

Menu Overview 60

Page 64

Menu Overview

Continued from page 59

61 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 65

Menu Overview

Menu Overview 62

Page 66

Appendix A

Clack

Flow Device K-Factor Data

Autotrol

Signet/ Seametrics

Meter Type Installation Fitting

Type (if applicable)

Hi-Flo 22 Integral 78 295.2

Clack Brass Tee 1.5” 0.75 to 75 37 140

Clack Stainless Steel Tee 2.0” 1.5 to 150 20 75.7

Autotrol Plastic Body w/SS ends 1.5” 7 to 250 15 56.8

Autotrol Plastic Body w/SS ends 2” 7 - 250 15 56.8

SeaMetrics

Paddlewheel

Type K Copper Tee

Signet

Paddlewheel

(Blue Nut)

Type L Copper Tee

-Sch 40 Copper Pipe

-Sch 40 Bronze Pipe

-Sch 40 Brass Pipe Weldolet

All 2” 3.1 - 195.8 18 58.1

All 3” 6.6 - 440.6 11 41.6

All 4” 11.74 - 783.2 6.5 24.6

Sch. 80 PVC Tee

Sch. 40

Galvanized Tee

Sch. 40 Steel

Pipe Saddle

Sch. 80 PVC

Saddle

Brazolet

-Sch 40 Steel Pipe

Pipe Size Flow Range

(Gal. Per Min.)

1” 0.6 - 42 352.4 1333.8

1.25” 1.2 - 77 177.2 670.7

1.5” 1.6 - 106 117.9 446.3

2” 2.7 - 179 66.7 252.5

2.5” 3.8 - 256 43.0 162.8

3” 6.0 - 401 26.7 102.1

1” 0.7 - 44 213.0 806.2

1.25” 1.2 - 80 127.7 483.3

1.5” 1.7 - 110 94.4 357.3

2” 2.8 - 184 58.4 221

1” 0.7 - 48 256.4 970.5

1.25” 1.1 - 75 176.4 667.7

1.5” 1.6 - 107 115.7 437.9

2” 2.8 - 187 63.4 240

1” 0.8 - 51 241.6 914.5

1.25” 1.2 - 78 170.9 646.9

1.5” 1.7 - 110 112.0 423.9

2” 2.9 - 192 61.7 235.5

2.5” 4.5 - 298 37.6 142.3

3” 6.9 - 460 23.2 87.8

4” 11.9 - 793 13.3 50.3

2.5” 3.9 - 256 43.0 162.8

3”` 6.0 - 401 26.7 101.1

4” 10.5 - 701 15.0 56.8

2.5” 4.0 - 264 37.6 142.3

3” 6.2 - 411 24.3 92

4” 10.8 - 716 13.9 52.6

K-Factor -

Gallons

K-Factor -

Liters

63 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 67

GBE Controller Parts & Accessories List

Part Number Item

Complete Controls

01020677 GBE Controller Complete for CSM, HF50 Softener

GBE Controller Complete for CSM, HF42, HF50 Filter

Hi-Flo 22 Softener Control Valve with GBE Controller

Hi-Flo 22 Filter Control Valve with GBE Controller

HF3e Conversion Kit – 2”

HF3e Conversion Kit – 1-1/2”

Accessories and Replacement Parts

01020745 Replacement GBE Board

01020497 Replacement Key pad

01020748 Auxiliary Board

01020747 Modem Board

01020750 RF Board

01020553 Remote Display - Complete

0101 Transformer

01020447 Smart Brine Tank Accessory

01008779 Aqua-Sensor – Steel Tank

01018959 Aqua-Sensor – Fiberglass Tank

CR 2032 Battery

Cables and Kits

01016327 Communication Cable

01016342 Communication Cable – Duplex Alternating

01016333 Duplex Progressive Kit

01016334 Triplex Progressive Kit

01016369 Duplex Alternating Kit

0102 SBT Extension Cable, 20ft

0102 PLC-USB Communication Cable w/CD

0102 PLC-RS485 Communication Cable

0102 PLC-RS232 Communication Cable

Appendix B

Appendix B 64

Page 68

Appendix C

Culligan GBE Controller – Data Port Output

The GBE controller is used to control water softeners, filters and commercial RO systems. This controller has the ability to provide “status messages” to a customer’s equipment using RS-232 and RS-485 communication protocols. These protocols are commonly used to send information from the GBE to either a customer’s PC or to a building management system or programmable logic controller (PLC). The information is “one-way” in that the GBE can send this information out, but the GBE cannot receive or respond to any commands sent into the communication port. The GBE sends a “status message” every 10 minutes. The information is send as a short text (ASCII), comma separated string of letters and numbers.

The information contained in the “status message” depends upon what type of equipment is being controlled by the GBE.

Single Water Softener or Filter controlled by GBE:

The format of the “status message” is: CULL,A,B,C,D,E,F

Example: CULL,52754,57.2,1,911,0x0000,1

Where the values for the fields A thru F are as follows:

A = total gallons since new B = current flow rate in gallons per minute (57.2 means 57.2 gallons per minute ) C = Current Status Indicator (0 = initialization, 1=service, 2=prerinse, 3=regen, 4= standby) D = capacity remaining in gallons E = Error Flag (see below) F = 1

Error Bit Meaning

0 Internal Valve Leak 1 Salt Bridging Detected 2 Brine Line Blocked 3 Brine Tank Overfill Error 4 Replace Media Filter 5 No RF Remote Signal 6 AquaSensor Salt Error (possibly low salt or failed eduction) 7 Motor Homing Error 8 Motor Position Sensor Error 9 Low Salt Level in Brine Tank 10 (not used) 11 AquaSensor Probe Fault (probe has failed, not plugged in or AquaSensor transformer failed) 12 Less than 14 Days Salt

The error flag is sent as a hexadecimal number in the format 0xWXYZ as follows:

W X Y Z

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

65 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 69

Appendix C

Each error bit is either ‘0’ meaning that this error is NOT present, or ‘1’ meaning that this error IS present. Each of the four-bit sections (W, X, Y and Z) are then combined into a four digit binary word which is converted to a hexadecimal digit.

As an example, if there are no errors present, then the value would be 0x0000.

If there were a ‘Replace Media Filter’, ‘Aquasensor Salt Err’ and ‘Motor Position Sensor Error’ present then bits 4, 6 and 8 would be set to ‘1’ respectively and all other bits would be ‘0’.

W X Y Z

Error Bits

Binary

hexadecimal

Error Flag

*note that the first two characters of the error flag are always “0x” to signify that this is a hexadecimal number ** In hexadecimal, the number 4 bit equals 1, the number 5 bit equals 2, the number 6 bit equals 4, and the number 7 bit equals 8. Therefore, when you add the #4 bit value to the #1 bit value, you get 5.

So the value of the error flag would be 0x0150 if these three errors were present.

NOTE: If the GBE is controlling a Filter (instead of a water softener) then the above message definitions are identical, but that error flags 1,2,3,6,9 and 11 will always be zero for a filter)

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

0 0 0 0 0 0 0 1 0 1 0 1 0 0 0 0

0 1 5** 0

0x0150

Progressive Flow System of Water Softeners controlled by GBE:

The format of the “status message” for a progressive flow network consists of a series of individual lines of information, one line for each of the gbe controlled softeners. For example, in a triplex progressive flow network, every 10 minutes, the data port on the master unit will send out the following three lines of information:

CULL,A1,B1,C1,D1,E1,1 CULL,A2,B2,C2,D2,E2,2 CULL,A3,B3,C3,D3,E3,3

example: CULL,52754,3.7,1,9110,0x0000,1 CULL,42674,3.5,1,4321,0x0000,2 CULL,10204,0.0,4,5444,0x0000,3

The ‘1’ at the end of the first line indicates that this line is the status for the Master unit in the progressive flow network. The ‘2’ and ‘3’ on the subsequent lines indicate that this data is for slave unit #1 and slave unit #2 respectively. The information contained on each line is of the same format as described in the Single softener section above.

Electrical Connections

The Culligan Data Cable Connector is terminated with a D-sub9 style female termination. The customer must provide the following pin connections:

Appendix B 66

Page 70

Appendix C

Pin Function

3 (input) TD (data coming FROM the GBE board) 2 (output) RD (this line is required even though no data is sent TO the GBE board) 7 (input) RTS 8 (output) CTS 5 (signal gnd) GND

The data coming from the GBE board is at the following conditions:

Bits Per Second: 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control: None

The following style data cables are available from Culligan:

Cable P/N: xxxxxxxx 9-pin female RS-232 output

Cable P/N: xxxxxxxx 9-pin female RS-485 output

Cable P/N: xxxxxxxx USB style output cable - comes with CD-ROM which includes

device drivers for Microsoft Windows VISTA, XP, and Windows 2000 operating systems

Test Data Port

Once your cables are set up, you can test your connection using the Windows’ Hyperterminal program. This program is generally found under Start/All Programs/Accessories/Communications/

Hyperterminal

When you open Hyperterminal it will ask you to create a name for the connection. Enter any name you choose and click OK.

Next you are asked to select a COM port. From the drop down list, pick the COM port with the highest number and click OK.

Next you are asked to set the properties for this COM port. They should be set as shown.

After you click OK, Hyperterminal is ready to accept data.

67 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 71

Return to the GBE controller and press the Down Arrow to enter the Menu.

Using the down arrow, scroll down to number 5, Advanced Setup, and press the checkmark.

Using the down arrow, scroll to number 5, Diagnostics, and press the checkmark.

Scroll to number 6, Use Data Port. When you press the checkmark, the GBE controller will send a test message to the Hyperterminal screen. It will look similar to this:

If you do not see the report, check your settings and make sure

Appendix C

*** MINI REPORT ***

SN = 00001078 Date = 9/4/8 Time = 14:02 Total = 28696 GAL regen 14d = 0 trigger = Power Outage type = softener hardness units = US Hardness = 25 grains Resin = 1.00 cu/ft avg mon = 710 GAL avg tue = 937 GAL avg wed = 1201 GAL avg thr = 839 GAL avg fri = 1364 GAL avg sat = 85 GAL avg sun gal = 710 GAL bw time = 10 min BD rinse = 71 min F rinse = 10 min

Fill = 441 sec Dosage = 9.0 LBS DAS = A Iron = 0 PPM Pressure = HIGH Salt type = NaCl Resin type = std BF Flow control = 0.45 GPM Eductor Flow control = 32.0 Reserve capacity = 25 % flow meter trig = yes aquasensor trig = yes regen interval = 7 predict mode = no day of week mode = none brine type = Downflow pre-rinse mode = yes prerinse after 24 hours prerinse for 5 mins units = US A/S = not installed SBT = inst

the cables are firmly connected. If you still don’t see the report, try some of the other COM ports.

Every 10 minutes you should see a status message on the screen that will look similar to this:

CULL,52754,57.2,1,911,0x0000,1

This message was described at the beginning of this Appendix.

Appendix C 68

Page 72

Appendix D

69 CULLIGAN GLOBAL ELECTRONIC CONTROLLER

Page 73

Index

Accessories 33-45 Alternating 3, 11, 13-14, 17, 22, 42, 64 Aqua-Sensor 3, 7, 8, 15, 21-22, 33, 53, 64 Auxiliary Board 46-47 Auxiliary Outputs 2, 11, 16, 43, 46-48 Beeper 1, 19, 33 Brine Reclaim 2, 22, 43 Brine Refill 6, 10, 22, 27, 31, 47-48, 50, 55 Cable 6, 7, 9, 11, 12, 13, 15, 17, 64 Check Sensors 55-57 Clock 52 Communication Cable, 6, 7, 11, 12, 13, 17, 64 Customizing the setup 28-34 Cycle Times 21-22, 27, 31-32, 42 Data Phone Number 44 Diagnostics 2, 21, 27, 40, 50, 54-57 Error Codes 53 Features 1-2 First Time Setup 22,23-27,58 Flow Meters 1, 3, 7, 12-14, 18, 22, 32, 41, 42, 55, 63 Information 51-52 Installation - Electrical 4-17 Jumper 12 Keypad - Beeper 1, 19, 33 Keypad - Lockout 58 Keypad 1, 7, 19, 20, 58, 64 K-Factors 1, 22, 41, 63 Manual Cycling 50 Manual Regeneration 49 Menu Lockout 58 Metric 30 Modem 2, 21-22, 23, 35, 37-41, 53, 64 Multi-Tank Systems 42 Outputs 2, 11, 16, 43, 46-48 Parallel 11, 12, 22, 42 Parts List 64 Phone Number 40, 44 PLC Output 65 Programming 18-58 Progressive Flow 2, 3, 11, 12, 13, 21, 22, 29, 41-42, 64 Pulses per gallon 41 Quick Reference 70 Reclaim 2, 22, 43 Refill 6, 10, 22, 27, 31, 47-48, 50, 55 Regeneration 30-31 Remote 2, 21, 22, 35-37, 38, 39, 53, 64 Reserve Capacity 30 SBT 2, 21-22, 51 Sensors 55-57 Service Phone Number 44 Setup - Advanced 28-30 Setup - Commercial 22

Setup - Customizing 28-34 Setup - Cycle Times 31 Setup - First Time 23-27 Setup - Multi-Tank Systems 42 Setup - Regeneration 30-31 Setup - Reneration Triggers 21, 32 Setup - Wireless Remote 36-37 Smart Brine Tank 2, 21-22, 51 Statistics 54 Time Clock 3 Time Zone 39 Transformer 4, 8-9, 15, 64 Triggers 21, 32 Units of Measure 30 Wireless Remote 2, 21, 22, 35-37, 38, 39, 53, 64

Index 70

Page 74

This page contains materials and DCO information.

IT DOES NOT PRINT AS PART OF THE DOCUMENT!

VENDOR MUST SUBMIT A MATERIAL CERTIFICATE OF COMPLIANCE WITH EACH SHIPMENT.

Materials & Description: Global Electronic (GBE) Softener & Filter Controller IO Guide

PN 01021161

Size: 8.5” x 11”

Color: Black Ink, 2 sided

Stock: Front (2 sided) & Back (Blank) Covers on 110# White Index

Inside on 20# white

Other: Collate

Tape Bind, Black Down the 11” left side

3 Hole Drill

LET CHANGE BY APRVD DCO DATE

A NEW ART CREATED BSM KR 010703 08/13/08

A1 Revisions BSM KR 010703 09/04/08

A2 Revisions BSM KR 010703 09/18/08

A3 Revisions BSM KR 010703 09/25/08

A4 Minor revisions BSM KR 010703 10/02/08

A5 Minor revisions BSM KR 010703 10/15/08

A6 Minor revision BSM KR 010703 10/16/08

Culligan 01020553, 01020606 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual