Page 1
3-in-1 Stainless Five Burner Gas Grill
ASSEMBLY IN STRUC TIONS
Model GAS9556AS / GAS9556ASO
Page 2
ASSEMBLY INSTRUCTIONS:
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR GRILL.
WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN AS SEM BLING THIS UNIT.
The following tools are required to assemble this Cuisinart 5 Burner Gas Grill:
• Phillips Screwdriver
• Pliers or Wrench
PARTS LIST:
1
1 Front Right Leg
2
1 Front Panel
3
1 Front Left Leg
4
1 Side Panel
5
1 Left Side Panel
6
1 Cart Brace
7
1 Cart Base
8
1 Left Rear Leg
9
1 Back Panel
10
1 Right Rear Leg
11
1 Side Burner Grate
12
5 Heat Tents
13
1 Side Burner Knob
14
1 Right Side Control Panel
15
1 Grease Cup
16
1 Warming Rack
17
1 Heat Shield
18
1 Right Side Table
19
1 Left Side Table
20
1 Grill Body
21
1 Left Side Control Panel
22
4 Casters
23
3 Cooking Grates
24
1 Grease Tray
25
1 Griddle
26
1 Smoke Tube
27
2 Griddle Hooks
28
28
1 Bar
Note: Most hardware is pre-attached to the grill. You may need to loosen some screws
partially while others may need to be removed in order to assemble parts. The screws that
you remove will be re-used so don’t misplace this hardware.
Extra screws are included in a small bag with the owners manual.
1
Page 3
20
15
25
21
19
18
16
23
12
8
26
10
14
13
11
22
17
27
5
3
9
2
7
6
28
1
24
4
2
Page 4
Step 1
FRONT PANEL
• Loosen 6 screws
3-4 turns
• Do not remove
screws
• Attach FRONT
PANEL using
2
keyholes
• Tighten 6 screws
1
NOTE: Before tightening keyhole
screws, make sure panels are aligned.
2
3
Step 2
• Loosen 3 screws
• Attach SIDE
PANEL
• Tighten 3 screws
on SIDE PANEL
4
SIDE PANEL
4
4
1
2
3
3
Page 5
1 2 3
5
LEFT
SIDE
PANEL
Step 3
• Loosen 2 screws
• Attach LEFT
SIDE PANEL
• Tighten 2 screws
on LEFT SIDE
PANEL
5
5
CART BRACE
6
1 2 3
Step 4
• Remove 6 screws.
5
• Attach CART
BRACE.
• Tighten two
screws on CART
BRACE.
6
6
Remove 2 screws
Remove 2 screws
4
Page 6
Step 5
• Attach CART BASE
7
• Make sure TANK
• BRACKETS are on this
end. (See drawing below)
• Tighten 4 screws
(Removed from Step 4)
TANK BRACKETS
4
1
2
3
CART BASE
7
Tighten 4 screws
Step 6
• Loosen 6 screws
• Attach BACK
PANEL
• Tighten 4 screws
• Remove 6 screws
9
8
Remove 2 screws
BACK PANEL
9
Remove 2 screws
10
Remove 2 screws
5
Page 7
Step 7
• Attach CART
7
BASE to back
legs
7
LEFT
SIDE
PANEL
CART BASE
• Tighten 4 screws
(Removed from
Step 6)
Screws removed
Step 8
from Step 6
5
8
9
• Attach LEFT SIDE
PANEL and
CART BRACE
5
6
CART BRACE
10
• Tighten 4 screws
6
Page 8
Step 9
• Lock CASTERS
• Attach CASTERS
to legs
CASTERS
unlocked
Step 10
• Attach GRIDDLE
HOOKS to LEFT
SIDE PANEL
5
GRIDDLE
HOOKS
7
6
3
9
locked
• NOTE: Washer
and nut used to
attach GRIDDLE
HOOKS go on the
back side of LEFT
SIDE PANEL.
7
LEFT
SIDE
PANEL
Page 9
TOP VIEW
Step 11a
6
Loosen bottom screws
CART BASE
• Loosen 2 bottom
screws
6
BAR
Tighten screw Tighten screw
CART BASE
Step 11b
• Install BAR
• Tighten 2 screws
8
Page 10
Step 12
• Set GRILL BODY
on cart
GRILL BODY
Step 13
• Remove 3 screws
• Align GRILL
BODY to cart
• Rotate CART
BRACKETS
upwards and
tighten 4 screws
Remove screw
GRILL BODY
CART BRACKETS
GRILL BODY
Tighten screws
Remove screw
Remove
screw
Align Panels
9
9
Page 11
GRILL BODY
Step 14
Remove
screw
Remove screw
Remove screw
• Remove 3 screws
• Align GRILL
BODY to cart
CART BRACKETS
• Rotate CART
BRACKETS
upwards and
tighten 4 screws
GRILL BODY
Tighten screws
Remove
screw
and
washer
LEFT SIDE
TABLE
RIGHT SIDE
TABLE
Remove
screw
and
washer
Step 15
• Remove 3 screws
and washers
RIGHT SIDE
CONTROL
PANEL
Remove
screw
10
Page 12
Step 16
• Loosen 4 screws
• Attach parts and
tighten screws
LEFT SIDE
CONTROL PANEL
RIGHT SIDE
CONTROL PANEL
Align
edges
Step 17
• Loosen 4 screws
• Attach LEFT SIDE
TABLE using
keyholes
• Do not tighten
screws at this
point in time
LEFT SIDE TABLE
Loosen 4 screws
RIGHT SIDE TABLE
LEFT
SIDE
TABLE
11
Page 13
Step 18
• Install screw and
tighten. (screw
was removed in
Step 13)
Align Panels
Step 19
• Install screw and
washer. (screw
and washer were
removed in step
15) Do not tighten
screw at this time.
• Make sure panels
are aligned
• Tighten 5 screws
from Step 17 & 19
12
Page 14
Step 20
• Loosen 4 screws.
• Attach RIGHT
SIDE TABLE
using keyholes.
Do not tighten
4 screws at this
time.
Loosen 4 screws
RIGHT
SIDE
TABLE
Step 21
• Install screw and
tighten (screw was
removed in step
14)
13
Page 15
Align Panels
Step 22
• Install screw and
washer (screw
and washer were
removed in step
15) Do not tighten
screw at this time.
• Make sure panels
are aligned and
tighten 5 screws
from Step 20 & 22
Step 23
• Install screw (removed in step 15)
4
14
Page 16
Step 24a
• Remove WING
NUT and remove
burner. Install
SIDE BURNER
VALVE in control
panel
• Rotate valve and
tighten 2 screws
to lock into place
(see diagram step
24b below)
SIDE BURNER
VALVE
BURNER VENTURI
WING
NUT
• Install burner and
make sure
BURNER
VENTURI ts over
VALVE NOZZLE
• Tighten WING
NUT
Step 24b
• Install SIDE
BURNER KNOB
VALVE
NOZZLE
BEZEL
KEY HOLES
SIDE BURNER
KNOB
15
SIDE BURNER
VALVE STEM
Page 17
SIDE
BURNER
WIRE CLIP
Step 25a
• Attach WIRE CLIP
to side burner
SIDE BURNER
VALVE
SIDE
BURNER
WIRE CLIP
Step 25b
SIDE BURNER
VALVE
16
Page 18
Step 26
• Attach IGNITOR
WIRE to ELECTRODE
ELECTRODE
IGNITER WIRE
Step 27
• Install SIDE
BURNER GRATE
SIDE BURNER
GRATE
17
Page 19
HEAT SHIELD
Step 28
• Loosen 2 screws
• Attach HEAT
SHIELD and
tighten screws
GREASE TRAY
GREASE CUP
Step 29
• Install GREASE
TRAY and
GREASE CUP
through back of
grill
18
Page 20
Step 30
• Install HEAT
TENTS,COOKING
GRATES and
WARMING
RACK
WARMING RACK
COOKING GRATES
HEAT TENTS
Step 31
• Store GRIDDLE
on GRIDDLE
HOOKS
• Store SMOKE
TUBE
SMOKE TUBE
STORAGE
GRIDDLE STORAGE
19
Page 21
Model GAS9556AS Assembled
AI9556AS/ASO
1118
©2018 The Boltz Group LLC
Addison, Texas 75001 U.S.A
Assembly Instructions for Model
GAS9556AS / GAS9556ASO
Loading...