Cuisinart BFP-703C User Manual

INSTRUCTION

BOOKLET

MARTPOWER

UET

Blender/

Food Processor

BFP-703C

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic safety precautions should always be followed, including the following:

1. READ ALL INSTRUCTIONS

BEFORE USING.

2. To protect against the risk of electrical shock, do not put motor base of SmartPower Duet

appliance in water or other liquid.

3. Close supervision is necessary when any appliance is used by or near children. Cuisinart does not recommend the use of this appliance by children.

4. Always unplug from outlet when not in use, before putting on or taking off parts, and before cleaning or removing contents from blender jar or food processor work bowl.

WARNING: Never put hands into the blender jar/food processor work bowl or container or handle the blades with appliance plugged in.

5. Avoid contact with moving parts.

6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to nearest Cuisinart service facility for examination, repair, and/or mechanical or electrical adjustment.

7. The use of attachments, other than those recommended by Cuisinart, including canning or ordinary jars not recommended or sold by Cuisinart, may cause fire, electrical shock, or risk of injury to persons.

8. Do not use outdoors.

9. Do not let cord hang over edge of counter or table or touch hot surfaces, which could damage the cord.

10. Keep hands and utensils out of

jar/food processor work bowl during use to reduce the risk of severe injury to persons or damage to blender itself. A

rubber or plastic spatula may be used but must be used only when the blender is turned OFF.

11. When motor base is in ON mode, and LED lights are flashing or glowing, do not touch cutting assembly, interfere with blade movement or remove blender Jar cover. Accidentally touching a speed button may activate the blender.

12. BLADES ARE VERY SHARP.

HANDLE CAREFULLY. Store out of reach of children.

13. To reduce the risk of injury, never place chopping blade/cutting assembly on base without the blender jar or food processor work bowl properly attached.

14. Always operate blender or food processor with the cover in place.

15. Never leave your blender or food processor unattended while running.

16. When blending HOT liquids in blender jar, remove measured pour lid (center piece of cover) to allow steam to escape.

17. Twist on locking ring firmly. Injury can result if moving blades accidentally become exposed.

18. Do not use an extension cord with this unit. Doing so may result

in fire, electrical shock, or personal injury.

19. Regarding your cord set: A

longer cord has been provided so that you will have flexibility in positioning your Cuisinart

SmartPower Duet

Blender/Food Processor near an electrical outlet. Exercise care when using the longer cord to avoid entangling or tripping over the cord. The longer cord should be arranged so that it will not drape over the counter or tabletop, where it can be pulled on by children or tripped over. Excess cord should be stored in the cord storage area at the back of the blender base to avoid injury caused by the longer cord.

20. Be certain the food processor cover is securely locked in place before operating appliance. Never operate without the cover locked securely in place.

21. Do not attempt to defeat the

food processor cover interlock mechanism.

22. Never feed food into processor by hand. Always use the food pusher.

23. Make sure the blade or disc has come to a full stop before removing cover.

24. This food processor attachment is to be used only with Cuisinart

SPB-7 series blenders. Do not use with any other manufacturer's blender base.

This appliance is intended for household use only.

25. Wash the blender jar, food processor work bowl, food processor chopping blade, locking ring, and covers before first use.

26. WARNING: TO REDUCE

THE RISK OF ELECTRICAL SHOCK OR FIRE, DO NOT REMOVE THE BASE PANEL. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE ONLY BY AUTHORIZED PERSONNEL.

SAVE THESE INSTRUCTIONS

FOR HOUSEHOLD USE ONLY

NOTICE:

This appliance has a polarized plug (one prong is wider than the other). To reduce the risk of electric shock, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.

Maximum rating of 350 watts is based on the jar attachment that draws the greatest power. Other recommended attachments may draw significantly less power.

UNPACKING INSTRUCTIONS

Place the gift box containing your Cuisinart

SmartPower Duet® on a flat, sturdy surface before unpacking. Remove instruction booklet and other printed materials from top of corrugated insert. Next, remove the top corrugated insert. Carefully lift blender base from box and set aside. Carefully remove slicing/shredding disc as it is very sharp. Remove food processor accessory. Remove the lower corrugated insert containing the blender jar assembly. Be careful not to tip the jar when removing. Remove any additional literature from the box. To assemble the blender, follow the “Assembly” instructions on page 4 of this instruction booklet. Replace all corrugated inserts in the box and save the box for repackaging. See the “Features and Benefits” section of this booklet for a listing of all blender parts.

Before using for the first time: Wash all parts according to the “Cleaning and Maintenance” section on page 5 of this booklet to remove any dust or residue.

TABLE OF CONTENTS

Important Safeguards . . . . . . . . . p.1

Unpacking Instructions . . . . . . . . p.2

Introduction . . . . . . . . . . . . . . . . p.2

Blender Features and Benefits . . p.2

Use and Care . . . . . . . . . . . . . . . p.3

Blender Assembly . . . . . . . . . . . . p.3

Blender Helpful Reminders. . . . . p.3

Blender Operation . . . . . . . . . . . p.4

Blender Quick Reference Guides p.4

Cleaning and Maintenance . . . . . p.5

Do’s and Don’ts . . . . . . . . . . . . . p.5

Food Processor Features &

Benefits . . . . . . . . . . . . . . . . . . . p.6

Food Processor Getting Started . p.6 Food Processor Assembly for

Chopping, Puréeing & Mixing . . p.6

Slicing & Shredding . . . . . . . . . . p.7

Food Processor Operating

Controls . . . . . . . . . . . . . . . . . . . p.7

Chop, Purée & Mix . . . . . . . . . . p.7

Add Food While Processing . . . . p.8

Removing Processed Food . . . . . p.8

Preparing Foods for Food Processing with Chopping Blade p.8

Slicing & Shredding. . . . . . . . . . . p.9

Preparing Foods for Slicing &

Shredding . . . . . . . . . . . . . . . . . . p.9

Recipe Tips . . . . . . . . . . . . . . . . p.9

Cleaning and Storing . . . . . . . . . p.10

Recipes. . . . . . . . . . . . . . . . . . . . p.10

Warranty Information . . . . . . . . p.20

INTRODUCTION

Congratulations! You have purchased two of Cuisinart's most versatile appliances wrapped into one! The SmartPower Duet

Blender/Food Processor combines Cuisinart's top-of-the-line 7-Speed Electronic Blender with our legendary Cuisinart

Food Processor. As a blender, the SmartPower Duet

Blender/Food Processor is the life of the party, engineered with seven speeds that let you purée, blend, mix, stir, liquefy and more. One speed is just for crushing ice, though ice can be crushed perfectly at any of the settings. You can make soups, salsas, thick and delicious frozen drinks, baby foods, etc. The blending capabilities are endless!

Attach the workbowl and cover and the Smartpower Duet

appliance

becomes a fully functioning Cuisinart

classic food processor. Chop raw and cooked foods, including meats, to any consistency. The reversible slicing/shredding disc and feed tube let you make mountains of vegetables, fruits and most cheeses in minutes. This combination of Cuisinart's two most versatile appliances into one promises years of happy and healthy food preparation.

As with all Cuisinart

appliances,

cleanup is quick and easy.

BLENDER FEATURES AND BENEFITS

1. Cover

is easy to use. Just press on; no turning or twisting required. Tight-fitting seal resists leakage.

2 oz. (50ml) Measured Pour Lid

allows you to measure and add ingredients neatly without removing the cover.

3. 40 oz. (1.25L) Glass Jar with Dripless Pour Spout

has a unique, sturdy, widemouth design and a dripless pour spout for no mess pouring.

4. Leakproof Rubber Gasket (not shown)

holds the glass jar snugly in position for safe operation.

5. High-Quality Cutting Assembly with Patented

rtP

™

Food

Processor

▲

Pulse

Mix

Purée

Stir

Off

Ice

Crush

Chop

11.

8b.

8a.

10.

8c.

Stainless Steel Blades

is strong enough for all blender tasks, including tough jobs, from ice crushing to chopping delicate herbs.

Note: Blades are very sharp…handle carefully.

6. Collar

is self-aligning so that the glass blender jar slides easily into position, eliminating the frustration of twisting and turning the blender jar to lock it into place.

7. Heavy Duty Motor Base

is so sturdy and stable, it will not “walk” on your counter – even during ice crushing! The motor is strong enough to handle all blending tasks, including crushing ice without liquid, and is backed by a three-year limited warranty.

8. 7-Speed Touch Pad Control with Indicator Lights

is easy to use, read and clean. Seven speeds give you great versatility-use low speeds for delicate blending all the way up to high speeds for cheese, garlic, or lemon zest. The red LED lights clearly indicate what blender speed you are using.

8a. Pulse Button

allows you to pulse at any speed from high to low, so you can blend ingredients only as much as needed.

8b. Ice Crush Button

(Blender Only)

activates the ice crushing speed. This button is preset to the best speed for crushed ice. However, you can crush ice at any speed. The Food Processor attachment is not intended to crush ice. Use

the Blender jar for this.

8c. Food Processor Button

is preset to the best speed for all food processing tasks. Always use this button when food processing. This speed may also be used with blender jar.

9. Slip- Proof Feet

prevent movement during use and prevent damaging marks on countertops or tables.

10. Hidden Cord Storage Compartment (not shown)

keeps countertop safe and neat by conveniently storing excess cord.

11. Impact-Resistant Plastic Housing

is crafted of the finest quality materials to resist staining, cracking, and odors.

12. Innovative Cuisinart Design

in combination with power, performance, sturdiness, and easy cleanup, makes this blender a winner.

*Backed by a three year limited warranty.

USE AND CARE

BLENDER ASSEMBLY

To use your Cuisinart®SmartPower Duet

Blender/Food Processor, begin

by assembling the blender jar.

Turn the blender jar (a) upside down, and place it flat on a sturdy surface.

Position the rubber gasket (b) on the round opening on the bottom of the blender jar.

Turn the cutting assembly (c) upside down, and place the blade end in the blender jar opening.

Note: Blades are very sharp… handle carefully.

Secure the rubber gasket and cutting assembly into position by placing the smaller opening of the locking ring (d) on top of the cutting assembly. Engage threads by twisting the locking ring clockwise until tightened. Make sure locking ring is tightly fastened

to blender jar. Once assembled, turn the blender jar right side up.

Push the cover onto the top of the blender jar. Push the measured pour lid into the cover.

Place the blender jar on the motor base so that the jar markings are facing you and the handle is positioned to one side.

Plug in power cord. Your blender is now ready to be used.

HELPFUL REMINDERS

•

Once the cover is in position, additional ingredients can be added during blending by simply lifting the measured pour lid, adding ingredients, and replacing the measured pour lid.

•

Cover should always be in place while the unit is ON.

•

Warning: Do not place blender jar on base while motor is running.

• Do not twist locking ring from

blender jar when removing blender jar from base. Simply lift blender jar from motor base.

• Boiling liquid or solid frozen foods

(with the exception of ice cubes or 1/2"(1.3cm) pieces of frozen fruit) should never be placed in the blender jar.

•

Do not place ice, frozen foods or very cold liquids into a blender jar which has come directly from a hot dishwasher.

•

Do not place very hot liquids or foods into a blender jar which has come directly from the freezer. Boiling liquids should cool for 5 minutes before being placed in blender jar.

•

Follow “Cleaning and Maintenance” instructions on

(d)

(c)

(b)

(a)

page 6 prior to your first use.

BLENDER OPERATION

1. Place the motor base of your Cuisinart

SmartPower Duet

Blender/Food Processor onto a flat, sturdy surface. It is important that the surface be clean and dry. Assemble the blender by following the “Assembly” instructions. Once the jar is assembled and is in position on the motor base, plug the Cuisinart

SmartPower Duet

Blender/Food Processor into an electrical outlet.

2. Add all necessary ingredients to the blender jar and replace the cover. You may add additional ingredients by lifting the measured pour lid and dropping ingredients through the fill area. Replace the measured pour lid after adding ingredients. Do not

place hands into blender jar with blender plugged in.

Note: Add liquid ingredients first,

then follow with solid ingredients. This will provide more consistent blending and prevent unnecessary stress on the motor.

Tip: Liquid ingredients can be measured in the measured pour lid using the measurement marking. Solid ingredients can be added by simply dropping them through the fill area into the blender jar. Replace the measured pour lid after adding ingredients.

Note:

To remove blender jar cover, lift

edge of cover upwards.

Lifting measured

pour lid will not remove cover.

3. TO START BLENDING: press the ON button. The red ON LED light will flash, indicating that the blender is turned on but no speed has been selected.

4. PRESS THE DESIRED BLENDING SPEED: both the ON indicator light and the activated speed indicator light will glow. The blender will now be functioning at the desired speed. It is possible to switch speeds without pressing the OFF button, by simply pushing the next desired speed button.

5. TO STOP THE BLENDING PROCESS: re-press the activated speed button. The blending process will stop. The red ON indicator light will continue to flash to let you know that the blender is still ON and can be reactivated by pushing the desired speed button. The blender can be completely deactivated and stopped from any speed by pushing the OFF button. You will need to press the ON button again to continue blending.

6. PULSE MODE: while the blender is turned ON, you can create a burst of power for quick, efficient blending by activating the PULSE function. To do so, first push the PULSE button, which will cause the PULSE indicator light to flash. Next, push and release the desired speed button. Repeat as desired. You determine the duration of each pulse. While pulsing, all indicator lights (the ON,

QUICK REFERENCE GUIDE

FOR BLENDER FUNCTION

To Activate Blender Press ON- The blender is in

ON Mode. To Begin Blending Press desired Speed Button. To Change Speeds Press desired Speed Button. To Pulse In ON mode press PULSE,

then press and release desired speed

button as needed. To Crush Ice In ON mode, press and release ICE

CRUSH Button as needed. To Stop Blending (and Deactivate Blender) Press OFF Button. To Stop Blending (in Pulse or ICE Release button.

CRUSH Mode) To Stop Blending in Stir, Chop, Mix, Purée, Press Speed Button again. This will

or Food Processor Mode return the blender to ON mode. Press

OFF Button to turn blender OFF.

SPEED SELECTION GUIDE

FOR BLENDER FUNCTION

Refer to this guide to choose the best speed for your desired result.

Ingredient/Recipe Speed Result

Reconstituting frozen

orange juice concentrate Stir Smooth and full-bodied

Mayonnaise Stir Thick and creamy Salad dressings Stir Desired consistency Nuts Chop Coarse to fine Whipping cream Mix Thick topping Bread crumbs Mix Uniformly fine Grating citrus zest Purée Uniformly fine Milk shakes Purée Smooth and creamy Baby food Purée Smooth and creamy Health drinks Food Processor Smooth and creamy Frozen cocktails Food Processor Thick and slushy Grinding hard cheese Food Processor Coarse to fine Spices Food Processor Coarse to fine Ice Ice Crush Snowy

Stir

Chop

▲

Ice

Crush

Mix

Off

Pulse

Food

Processor

Purée

the PULSE, and the desired SPEED) will glow.

The PULSE function can be used to break apart larger pieces of food or to control the texture of food when chopping. The PULSE function is also effective in starting the blending process when you do not want continuous power, or when processing items which do not require an extended amount of blending.

7. TO CRUSH ICE:

Use Blender Jar

Only. The SmartPowerDuet

Blender/ Food Processor motor is strong enough to crush ice without liquid at any speed; however, for your convenience we have preset the best speed for ice crushing. To give you greater control, the ICE CRUSH function automatically operates as a PULSE function. To crush ice, place ice cubes in the blender jar, and place the cover and the measured pour lid on the blender jar. Press the ON button. Press the ICE CRUSH button in short pulses until ice is crushed to desired consistency. See the "Recipe Tips" section on page 9 for more details.

8. TO DISLODGE FOOD: use a

rubber or plastic spatula to help remove food lodged around the cutting assembly. DO NOT USE SPATULA UNTIL YOU HAVE TURNED OFF AND UNPLUGGED THE BLENDER. Replace the cover and measured pour lid and continue blending if necessary. Make sure spatula is not inside the blender jar before blending.

9. WHEN FINISHED BLENDING: press the OFF button, and unplug the blender from the electrical outlet. Never remove the blender jar from the

motor base until pressing the OFF button. Do not twist locking ring from blender jar when removing jar from motor base. Simply lift blender jar from motor base. Do

not place hands into blender jar with blender plugged in.

CLEANING AND MAINTENANCE

Always unplug your Cuisinart

SmartPower Duet® Blender/ Food Processor

from the electrical outlet before cleaning. The blender is made of corrosion-resistant parts which are easy to clean. Before first use and after every use, clean each part thoroughly. Periodically check all parts before reassembly. If any part is damaged or blender jar is chipped or cracked, DO NOT USE BLENDER.

Remove the blender jar from the motor base by lifting straight up and away. Twist off the locking ring by turning counterclockwise. Remove the cutting assembly and rubber gasket. Wash in warm soapy water, rinse and dry thoroughly. Place the locking ring in the upper rack of the dishwasher or wash in warm water.

CAUTION: Handle the cutting assembly carefully. It is SHARP and may cause injury. Do not attempt to remove blades from cutting assembly.

Remove the blender jar cover and the measured pour lid. Wash in warm, soapy water; rinse and dry thoroughly, or place in the upper rack of the dishwasher. The blender jar should be washed in warm soapy water and rinsed and dried thoroughly. The blender jar can also be placed upside down in the dishwasher.

Finally, wipe the motor base clean with a damp cloth to remove any residue

and dry thoroughly. Never submerge the motor base in water or other liquid, or place in the dishwasher.

Tip: You may wish to clean your blender cutting assembly as follows: Squirt a small amount of dishwashing liquid into assembled blender jar and fill halfway with warm water. Run on STIR for 15 seconds. Repeat using clean tap water. Empty blender jar and carefully disassemble parts. Wash cutting assembly, gasket and locking ring in warm, soapy water. Rinse and dry all parts thoroughly.

DOSAND DON’T

WHEN USING YOUR BLENDER/FOOD PROCESSOR

DO:

• Make sure the electrical outlet is rated at the same voltage as that stated on the bottom of the blender motor base.

• Always use the motor base on a clean, sturdy and dry surface.

•

Always add liquid ingredients to the blender jar first, then add remaining ingredients. This will ensure that ingredients are uniformly mixed

• When using either appliance, cut most foods into cubes approximately 1/2" to 1" (1.3cm to 2.5cm) to achieve a more uniform result. Cut all cheeses into pieces no larger than 1/2"(1.3cm).

• When using blender, use the measured pour lid to measure liquid ingredients such as alcohol. Replace measured pour lid after ingredients have been added.

• When using either appliance, use a rubber or plastic spatula as needed only when the blender is turned

OFF. Never use metal utensils, as damage may occur to the blender jar/work bowl or cutting assembly.

• Place blender cover on firmly. Always operate the blender with the cover on.

• Make sure locking ring is tightly

attached to blender jar.

• When using blender, always remove locking ring, cutting assembly, and rubber gasket before cleaning.

• When scraping the blender jar with a spatula, remove the food from the sides of the blender jar and place it in the center of the blender jar, over the cutting assemb

ly.

•

When chopping fresh herbs, garlic, onion, zest, bread crumbs, nuts, spices, etc., make sure the blender jar and cutting assembly are completely dry.

• If food tends to stick to the sides of the

blender jar or food processor work bowl during use, pulse in short bursts.

• When using food processor, pulses

should be short bursts. Space the pulses so the blades stop rotating between pulses.

DON’T:

• Don’t store food or liquids in your blender jar or food processor work bowl.

• When using blender, don’t place cutting assembly and locking ring onto motor base without the blender jar attached.

• Blender or food processor will not mash potatoes, knead dough, or beat egg whites.

• Don’t remove blender jar or food processor bowl while unit is ON.

Keep the blender jar or food processor cover on while blending.

• Don't twist locking ring from

blender jar when removing blender jar from motor base. Simply lift blender jar from motor base.

• Don’t overprocess foods. Blender or food processor will achieve most desired results in seconds, not minutes.

• Don’t overload blender or food processor. If the motor stalls, turn OFF immediately, unplug the unit, and remove a portion of the food, then continue.

• Don’t use any utensil inside the blender jar or food processor bowl while the motor is ON.

• Don’t use any container or accessories not recommended by Cuisinart. Doing so may result in injury.

• Don’t place hands inside the blender jar or food processor bowl when blender is plugged in.

• Don’t add boiling liquids or frozen foods (except ice cubes or 1/2" (1.3cm) pieces of frozen fruit) to glass blender jar. Boiling liquids should cool for 5 minutes before being placed in blender jar.

• The food processor accessory is not intended to crush ice. This could damage the chopping blade and will damage work bowl.

FOOD PROCESSOR FEATURES AND BENEFITS

1. Food Pusher with Oil Dispenser

2. Bowl Cover with feed tube

3. Sharp stainless steel chopping blade chops raw and cooked food to any consistency from coarse chop to fine purée

4. Stainless steel reversible slicing/shredding disc makes perfect slices

5. Adapter stem

6. Clear work bowl

7. Gearbox Collar

8. Same motor base used for both the blender jar and the food processor bowl

FOOD PROCESSOR STEP BY STEP GETTING STARTED

Please note that the bowl with collar will fit on the base in eight different positions. The handle can be in front or on either side and the feed tube in front, back, or on either side. Directions for use reference a certain position for instructional purposes only.

FOOD PROCESSOR ASSEMBLY FOR CHOPPING, PURÉEING & MIXING

1. Hold gearbox collar in one hand and work bowl handle in the other. Twist bowl clockwise onto collar.

2. Place collar with bowl onto motor base with handle facing front.

3. Place chopping blade over shaft in work bowl. Chopping blade should

slide easily to the bottom of the bowl. Lower blade will almost touch bottom of bowl.

BE SURE TO HANDLE THE METAL BLADE WITH CARE AS IT IS RAZOR SHARP!

4. Place food to be processed in work bowl. Put cover on work bowl, with feed tube at about 11 o’clock. Turn the cover clockwise until it fits into position. Cover lock must click

into locked position prior to use. If you have trouble fitting the cover on

Food Pusher with Oil Dispenser (1)

Bowl Cover with Feed Tube (2)

Reversible Slicing/ Shredding Disc (4)

Stainless Steel Chopping Blade (3)

Adapter Stem (5)

Work Bowl (6)

Gearbox Collar (7)

Blender Base (8)

3. Place chopping blade over shaft in work bowl. Chopping blade should

™

SmartPower

Duet

L E

N D

E R

/ F

D P

E S

Ice

Stir

Pulse

Crush

Food

Chop

Processor

Purée

Mix

▲

Off

Stir

Chop

Mix

▲

+ 15 hidden pages

Cuisinart BFP-703C User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual