CRU DataPort 3 SATA User Manual

DataPort 3 Installation Guide

Affordable removable hard drive enclosure.

Preparation for Installation

Note: To prevent data loss, read this manual before

installing or operating the DataPort 3. Before touching
any electrical equipment, ground yourself by touching
the metal part of your computer chassis. This discharges
static electricity and prevents any damage to your com­puter. CRU is not responsible for static discharge damage.

Tools Required

Phillips screwdriver

Other Items that May Be Needed

Rugged, Reliable, Mobile, Secure

TM

Mounting a Hard Drive in the Carrier

1. Remove the carrier top cover. The cover of the
DataPort 3 slides into place on the carrier without
any screws.

2. Place the drive in the carrier and connect the male
connector on the hard drive to the female connector
on the carrier.

Computer Users Manual.
Serial ATA cable

Frame Installation

to mount the DataPort 3 frame assembly. Remove
any fi ller plates that may be present.

one on each side of the frame. The mounting rails
should be provided with your computer system.

If needed, use the screws provided to secure the
frame assembly to the PC case with the frame’s side
mounting holes.

ate Serial ATA connector on the frame.

computer power supply and plug it into the power
receptacle on the frame.

3. Secure the drive in the carrier, using the four
screws provided to mount the drive. Position the
cables inside the carrier assembly so that they are
completely enclosed within the carrier.

nalp uoy hcihw ni yab thgieh-flah ”52.5 eht yfitnedI .1

llatsni ,sliar gnitnuom seriuqer yab evird eht fI .2

.esac CP eht fo yab ”52.5 eht otni emarf eht edilS .3

-irporppa eht ot ti tcennoc dna elbac atad eht etacoL .4

nip-4 elbaliava na etacoL .5

eht morf elbac rewop CD

4. Ensure that the lock of the DataPort 3 is in the
“open” (vertical) position. Slide the carrier into the
frame. Using thumb pressure, fully seat the carrier
in the frame, then lock the unit with the keylock.

The frame installation is now complete.

1-800-260-9800 www.CRU-DataPort.com

Rugged, Reliable, Mobile, Secure

TM

You have finished the installation and your DataPort 3

is ready to operate.

Operation

Turn on the Power

The lock on the CRU DataPort 3 locks the carrier in
place and also serves as an “ON/OFF” switch for the
power. Turn the lock 90 degrees clockwise to the “ON”
position before turning on the computer. When the
computer is turned on, the “Power On” LED (green
light emitting diode below the key on the frame as­sembly) is illuminated, and the system should operate
normally.

IMPORTANT: READ THE FOLLOWING BEFORE REMOV­ING THE CARRIER.

Removing the DataPort 3 carrier while the computer is
operating is not recommended. If you need to remove the
carrier while the computer is running, observe the following
precautions:

Wait until the drive activity light has stopped, indicat­ing that no read/write activity is occurring. If your sys­tem uses a disk caching program, ensure that all the
data has been written to the hard drive. Turn off the
drive by turning the key to the “OFF” (vertical) position.
The power LED will go off, indicating that the power
has been cut. Wait 10 to 15 seconds for the drive to
stop spinning, and then remove the carrier.

CRU is not liable for loss of data. It is the user’s re-
sponsibility to follow these important procedures to
safeguard data.

Troubleshooting

Drive Not Recognized by Computer

First check all of the cable connections. Ensure the
carrier and frame are fully seated and none of the
pins were bent during carrier insertion.

Fan Failure

For Fan Failure contact CRU Technical Support.

Product Warranty

CRU-DataPort (CRU) warrants the DataPort 3 to be free of
significant defects in material and workmanship for a period
of two (2) years from the original date of purchase. CRU’s
warranty is nontransferable and is limited to the original
purchaser.

Limitation of Liability

The warranties set forth in this agreement replace all
other warranties. CRU expressly disclaims all other war­ranties, including but not limited to, the implied warranties

of merchantability and fitness for a particular purpose and

non-infringement of third-party rights with respect to the
documentation and hardware. No CRU dealer, agent or
employee is authorized to make any modification, exten­sion, or addition to this warranty. In no event will CRU or its
suppliers be liable for any costs of procurement of substi-

tute products or services, lost profits, loss of information or

data, computer malfunction, or any other special, indirect,
consequential, or incidental damages arising in any way out
of the sale of, use of, or inability to use any CRU product or
service, even if CRU has been advised of the possibility of
such damages. In no case shall CRU’s liability exceed the
actual money paid for the products at issue. CRU reserves
the right to make modifications and additions to this product
without notice or taking on additional liability.

No Power

Make sure the lock of the DataPort 3 is turned to the
“ON” position and the green power LED light is on.
Check the 4-pin DC power connection both inside the
carrier and on back of the frame.

Register your product at www.CRU-DataPort.com and be

automatically entered to win a free prize!

A5-003-0002 Rev. 1.0

1-800-260-9800 www.CRU-DataPort.com