Crown DCi 8|600ND, DCi 4|1250ND Datasheet

Digital Signal Processing (DSP) Features:

• LevelMAX™ limiters for inputs and
outputs with thermal limiting

• Input and output delay

• Input and output EQ

• Signal generator

• Crossover

Standard Features:

• Crown’s DriveCore™ technology
includes five patents, providing best-
in-class versatility and durability

• The next generation of PWM
technology using cutting edge Class
D amplifier topologies

• Minimum Guaranteed Power Ratings

• Compatible with HiQnet Audio
Architect™ software

• Direct drive "constant voltage"
capabilities on channel by channel
basis at 70Vrms and 100Vrms

• Advanced PFC universal power
supply; universal AC input accepts
100 – 240VAC, 50/60Hz (±10%)

• TCP/IP based protocol in HiQnet for
network monitoring and control

• Revolutionary cooling system;
focuses airflow on parts that need it
most for maximum efficiency

• Audio Video Bridging (AVB) Ethernet
transport port

Network & Control Features:

• Continuous load monitoring

• Comprehensive error reporting

• Pilot tone monitoring

• Programmable general purpose
input/output (GPIO) ports

Features

\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\

DCi Network Display Series

INSTALLS ANYWHERE. OUTPERFORMS EVERYTHING.

Performance Specifications

8|600ND 4|1250ND

Frequency Response

(8Ω, 20Hz - 20kHz)

±0.25dB ±0.25dB

AVB Signal-to-Noise Ratio
(ref. rated power, 8Ω,
20Hz - 20kHz)

>108dB >108dB

Analog Input Signal to Noise

Ratio (ref. rated Power, 8Ω,

20Hz - 20kHz

>104dB >104dB

Total Harmonic Distortion
(at full rated power,
20Hz - 20kHz)

0.35% 0.35%

Voltage Gain
(at Maximum Level Setting)

34dB 34dB

Damping Factor
(20Hz to 100Hz)

>1000 >1500

Input Impedance (nominal
balanced, unbalanced)

10kΩ, 5kΩ 10kΩ, 5kΩ

Maximum Input Level
before Compression
(Low Gain Mode)

+20dBu +20dBu

Load Impedance
Stereo/Dual Mode

2Ω - 16Ω; 70Vrms and 100Vrms

Load Impedance
Bridge Mono

4Ω - 16Ω; 140Vrms and 200Vrms

Cooling

Continuously variable speed forced air, front to back airflow

Maximum Fan Noise
(re dBA SPL @ 1M)

47 47

Required AC Mains (±10%)

100V - 240V ~50/60Hz 100V - 240V ~50/60Hz

IEC Power Connector

20A IEC 20A IEC

Physical Specifications

Width

19 in. (48.3 cm) 19 in. (48.3 cm)

Height

3.5 in. (8.9 cm) 3.5 in. (8.9 cm)

Depth

17 in. (42.5 cm) 17 in. (42.5 cm)

Weight

30 lbs (13.60kg) 30 lbs (13.60kg)

DriveCore™ Install Network Display

\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\

Model

Channels

2Ω 4Ω 8Ω 16Ω 70Vrms 100Vrms

8|600ND 8 300W 600W 600W 300W 600W 600W

4|1250ND 4 1250W 1250W 1250W 625W 1250W 1250W

8 channel model

4 channel model

Power Matrix

Specifications subject to change without prior notice. Latest information available at www.crownaudio.com. Crown offers a three-year, no-fault, fully transferable warranty for every new Crown amplifier – an unsurpassed industry standard. With this unprecedented no-fault protection, your new Crown
amplifier is warranted to meet or exceed original specifications for the first three years of ownership. During this time, if your amplifier fails, or does not perform to original specifications, it will be repaired or replaced at our expense. In most cases, the only things not covered by this warranty are those
losses normally covered by insurance and those caused by intentional abuse. Plus, the coverage is transferable, should you sell your amplifier. See your authorized Crown dealer for full warranty disclosure and details. For customers outside of the USA, please contact your authorized Crown distributors for
warranty information or call 574-294-8200. © 2015 Crown Audio®, Inc.