Crosley CDBEH950SW1A, CDBEH950SS1A, CDBEH950SB0A, CDBEH950SS0A, CDBEH950SB1A Owner’s Manual

®

Crosley

All about the

Use & Care

of your Dishwasher

TABLE OF CONTENTS

Important Safety Instructions ......................2

Product Registration ...................................3

Features at a Glance ...................................4

Operating Instructions .............................5-6

Preparing and Loading Dishes ..................7-9

www.crosley.com USA and Canada 1-336-761-1212

P/N:A05752401RevB Artwork:A05752401Rev002 (January 2017)

Dishwasher Dispenser and Detergents .......10

Factors Affecting Performance ...................11

Care and Cleaning ....................................12

Before you Call ....................................13-15

Major Appliance Warranty .........................16

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Please read all instructions before using this

dishwasher.

For your Safety

• Use your dishwasher only as instructed in
this Use and Care Manual.

• This Manual does not cover every possible
condition and situation that may occur.
Use common sense and caution when
installing, operating and maintaining any
appliance.

• NSF certifi ed residential dishwashers
are not intended for licensed food
establishments.

• DISHWASHER MUST BE ELECTRICALLY
GROUNDED. Read the Installation
Instructions for details.

• This dishwasher is designed to operate on
regular house current (120V, 60Hz). Use
a circuit equipped with a 15 ampere fuse
or circuit breaker. Use a 20 ampere fuse
if dishwasher is connected with a food
disposer.

• Do not operate dishwasher unless all
enclosure panels are in their proper place.

• To avoid entrapment and/or suffocation,
remove door or door latch mechanism from
any dishwasher that is discarded or not in
use.

• Keep young children and infants away from
dishwasher when it is operating.

• Do not let children abuse, sit, stand or play
on door or racks of a dishwasher.

• Use only detergents and rinse agents
recommended for use in a dishwasher.

• Store dishwasher detergent and rinse
agents out of the reach of children.

• Do not wash plastic items unless marked:
“Dishwasher Safe” or equivalent. Check
with manufacturer for recommendations,
if not marked. Items that are not marked
dishwasher safe may melt and create a
potential fi re hazard.

• Disconnect electrical power to dishwasher
before servicing.

• If the dishwasher drains into a food
disposer, make sure disposer is completely
empty before running dishwasher.

• Repairs should be done by a qualifi ed
technician.

• Do not tamper with controls.

• Do not touch the heating element during or
immediately after

• Use care unloading the dishwasher when
the SANITIZE option has been selected.
Contents may be hot to the touch
immediately after the end of cycle.

• Water vapor from the vent may be hot to
the touch when the SANITIZE option has
been selected. Use care and do not let
small children play around or touch the
vent area of the dishwasher.

• When loading items to be washed:

Locate sharp items and knives so
that they are not likely to damage
the door seal or tub.

Load sharp items and knives with
the handles up to reduce the risk
of cut-type injuries.

• Under certain conditions, hydrogen gas
may be produced in a hot water, system
that has not been used for 2 weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If
hot water system has not been used for
such a period, before using dishwasher,
turn on for several minutes This will
release any accumulated hydrogen gas.
HYDROGEN GAS IS FLAMMABLE. Do no
smoke or use an open fl ame during this
time.

• Do not store or use combustible materials,
gasoline or other fl ammable vapors and
liquids in the vicinity of this or any other
appliance.

WARNING

To reduce the risk of fi re, electrical shock or
injury when using your dishwasher, follow
the above basic precautions.

WARNING

This symbols will help alert you to such
dangers as personal injury, burns, fi re and
electrical shock.

2

PRODUCT REGISTRATION

Thank you for choosing Crosley.
This Use & Care Guide is part of our

commitment to customer satisfaction and
product quality throughout the service life of
your new appliance.

We view your purchase as the beginning of a
relationship. To ensure our ability to continue
serving you, please use this page to record
important product information.

_________________________________
Purchase Date
_________________________________
Model Number
_________________________________
Serial Number

NOTE



Why Energy Effi cient Units run long
cycles: Several factors are important to
washing dishware. The energy use of your
dishwasher was reduced by applying more
of the factors that don’t use so much energy
and less of the ones that use more. As a
result, you will see that the wash cycles take
longer.

NOTE



Very Important Information

- Read Before Operating Your
Dishwasher!

Normal Operating Sounds

This dishwasher does not sound like most
dishwashers - IT’S QUIETER.

Your Precision Direct W ash S ystem® dishwasher
uses energy effi cient motors for the wash and
drain portions of the cycle you select. Each
cycle has a series of water fi lls and drains for
washing and rinsing dishes. As each cycle
begins, you may - or may not - hear the drain
motor.

The next sound you will hear is the splashing
water as it enters the tub. Then the lower arm
rotates and circulates water. This is followed
by a pause and a slightly different sound as the
upper arms spray water. If you listen closely,
you will hear the change in sound as the wash
action switches from one arm to the other.

PLEASE BE ADVISED: If you

compare this dishwasher to previous
models, you may be surprised at what
you DON’T hear.

3

FEATURES AT A GLANCE

Your dishwasher cleans by spr aying a mixture of hot w ater and detergent through the spray arms
against soiled surfaces. First, the dishwasher fi lls with water covering the fi lter area. Water is
then pumped through the spray arms. Soil particles go through and across the fi lter and down the
drain as the water is pumped out. This series of steps are repeated as needed. The number of
water fi lls vary with the cycle being used.

Nozzle or Spray Arm

Cup Shelves
(on some
models)

Middle Spray Arm

T ub Gask et

Top Rack

Serial Label
(Located on right

side of tub)

Lower Rack

Silverware Basket

Lower Spray Arm

Overfi ll Protector

Rinse Aid

Getting Started

1. Load Dishwasher (See Preparing and
Loading Dishes).

2. Add detergent (See Dishwasher
Dispenser & Detergents).

3. Add Rinse Aid, if needed (See Rinse
Aid).

4. Close door to latch.

5. Select desired CYCLE (See Cycle
Chart). The indicator light above the pad will
glow when selected.

6. Select desired OPTION (See Energy
Options). The indicator light above the pad
will glow when selected.

7. Run hot water faucet nearest
dishwasher until water is hot. Turn water off.

8. To start, press START/PAUSE pad.

Heating Element

Glass T rap

Detergent
Dispenser

* Appearance may vary from your model.

NOTE



The dishwasher is programmed to remember
your last cycle so you do not have to reset
each time. To start the dishwasher using
the same cycle and options selected on the
previous wash, just press the STAR T/PAUSE
pad.

Wash Cycle Selections

Cycle times are approximate and will vary with
options selected. Hot water is necessary to
activate dishwasher detergent and melt fatty
food soils. An automatic sensor will check the
incoming water temperature and, if it is not
hot enough, the cycle will be lengthened for
automatic water heating in the main wash and
fi nal rinse of all cycles. This happens even
when HI- TEMP WASH option has not been
selected. When HI- TEMP WASH is selected,
an even higher temperature will be reached to
handle heavier soil loads.

4

OPERATING INSTRUCTIONS

Option Selections
Hi-Temp Wash Option

When HI- TEMP WASH option is selected, the
dishwasher heats water in the main wash to
approximately 140

This increase in water temperature helps the
dishwasher detergent remove food grease and
soil from dishes more effectively and aids in
drying. HI- TEMP WASH option can be used
with HEAVY and NORMAL CLEAN only. HI-TEMP
WASH is automatically provided when the
HEAVY CLEAN cycle is selected.

When HI- TEMP WASH option is selected, the
light above the pad will come on and remain
on until end of cycle. To turn off the HI-TEMP
WASH option, press the pad a second time.
The light above the pad will turn off.

o

F (60oC).

Heat Dry/Air Dry

Use of the Heated Dry option, especially in
combination with use of a rinse agent, will
enhance drying. If Air Dry is selected the
heater will be de-activated during the drying
phase of the selected wash cycle. This will
slightly lower the energy use but will increase
the likelihood that the dishware will not dry
completely .

Sanitize Option

To sanitize your dishes and glassware, select
SANITIZE option. When selected, the light
above the pad will come on and remain on until
the end of the cycle. The water temperature
in the fi nal rinse will be raised to 155oF (68oC).
This option is available in Heavy and Normal
Cycles. Only these sanitization cycles have
been designed to meet NSF requirements.

The cycle time will be extended until the proper
water temperature is reached.

action will continue during the water heating
delay. For best results, the incoming water
temperature should be at least 120oF (49oC).

The sanitize criteria may not be satisfi ed if there
is an interruption of the cycle, power failure or if
the incoming water temperature is below 120oF
(49oC).

To turn off the SANITIZE option, press the pad
a second time. The light above the pad will
turn off.

NOTE



If the dishwasher door is opened while the
unit is running, the START/PAUSE pad must
be pressed and the door shut immediately
to return the unit to the selected cycle and
option, this must happen within 10 minutes
for the unit to continue the cycle.

Washing

Delay Start

The DELAY START option allows you to
automatically delay starting your dishwasher
for either 2-4-6 hours.

To activate delay start option for 2-4-6 hour
delay, press the pad once for a 2 hour delay,
twice for 4 hours and three times for 6 hours.
A light will come on indicating the delay start
hours and will remain on until cycle starts.
Press the START/PAUSE pad to start the delay
option. If the delay option is interrupted, the
START/PAUSE pad will have to be pressed
again to return to delay option.

To cancel the DELAY START option and begin
the cycle before the delay period is over, press
CANCEL pad.

Child Lock Controls

To prevent children from accidently changing
the dishwasher cycle or starting the
dishwasher, lock the dishwasher controls
by pressing and releasing the AIR DRY pad
for 3 seconds while the door is latched. An
indicator light on the lock graphic pad will
illuminate when the controls are locked and
no new selections can be made until the lock
is released. To unlock the controls, press the
same pad AIR DRY, until the indicator light
goes out.

Status Indicator Lights

The WASHING light comes on at the beginning
of the cycle and remains on until the end of
the main wash.

When the SANITIZE option is selected, the
SANITIZED light will glow when the SANITIZE
cycle is fi nished. If the dishwasher did not
properly sanitize the dishes, the light will not
come on. This can happen if the cycle is
interrupted. The light will remain on until the
door is opened.

The CLEAN light will come on at the end of
cycle and remain on until the door is opened.

To Cancel a Cycle

You can cancel a cycle anytime during the cy cle.
Press the CANCEL pad and dishwasher will start
a 90 seconds drain. At the end of the drain,
select the next desired cycle.

5

OPERATING INSTRUCTIONS

The DishSenseTM Technology checks the soil level on your dishes in the HEAVY CLEAN and
NORMAL CLEAN cycles. In response, automatic cycle adjustments are made to assure the
dishware gets clean - with less food residue left on the dishware the cycle time will be shorter.
Cycle time will also vary based on the options selected and the incoming water temperature.

Cycle Chart

Cycle and intended use Water per

Heavy Clean

Recommended for pots, pans,
casseroles and dinnerware
having light to heavily soiled
loads.

Normal Clean

Recommended for lightly to
heavily soiled loads.

Quick Clean

Recommended for a small
dish load and light soil.

Top Rack

Recommended for small loads
in the upper rack only.

Rinse Only

For rinsing dishware that will be
washed later.

* Does not include drying time

Available Options
Temperature;
Drying

Sanitize;
Heat Dry, Air Dry

Sanitize, Hi-Temp,
Normal;
Heat Dry, Air Dry

Normal;
Heat Dry, Air Dry

Normal;
Heat Dry, Air Dry

N/A

Cycle

5.5 - 8.9 gal.
21 - 34 L.

3.0 - 7.2 gal.
11 - 27 L.

5.1 - 5.9 gal.
19 - 22 L.

3.3 - 3.9 gal.
12 - 15 L.

2.2 - 2.5 gal.
8 - 9 L.

Duration*
(approx.)

3

/4 - 2 1/4 Hours

1

1

/4 - 2 Hours

1

33 Min.

1

/4 Hours

1 - 1

17 Min.

NOTE



The Normal cycle with its factory default options of normal temperature and heated dry
together provide the best all around performance. This cycle selection is recommended for
everyday use and is suitable for a large range of both load sizes and food quantities remaining
on those dishes.

6

PREPARING AND LOADING DISHES

Dish Preparation

Scrape away large pieces of food, bones,
pits, toothpicks, etc. The continuously
fi ltered wash fl uid will remove remaining food
particles. Burned-on foods should be loosened
before loading. Before loading them in the
dishwasher empty liquids from glasses and
cups.

Foods such as mustard, mayonnaise, vinegar,
lemon juice and tomato based products may
cause discoloration of stainless steel and
plastics if allowed to sit for a long period of
time. Unless the dishwasher is to be operated
at once, it is best to pre-rinse or use the rinse
only cycle to rinse off these food soils.

• Load racks so that large items do not
prevent the detergent dispenser from
opening.

• Check manufacturer’s recommendations
before washing items in question.

• If the dishwasher drains into a Food
Disposer, be sure disposer is

completely empty before starting
dishwasher.

10 place settings standard loading pattern

Loading the Top Rack

Features and appearance of racks and
silverware basket as shown may vary
from your model.

The upper rack is designed for fl exibility in
loading a wide variety of items including cups,
glasses, stemware, small plates, bowls, etc.

Load glasses in top rack only. Damage may
occur if placed in bottom rack.

Load plastic items in top rack only. Melting
may occur if placed in bottom rack.

Load items with open ends facing down for
better cleaning and drying.

Damage may occur if delicate items touch
each other during dishwasher operation.

Long-handled knives and utensils can be
placed in top rack.

Be sure nothing protrudes through the bottom
of the rack to block rotation of the middle
spray arm.

12 place settings standard loading pattern

Some models have a fold-down cup shelf
or a cup shelf/stemware holder. They can
be used to load two levels of cups, juice
glasses, and other short items. Stagger
items on upper level so that water can
reach all inside surfaces. Fold cupshelves
up to load tall glasses.

7

PREPARING AND LOADING DISHES

Top Rack

The TOP RACK option can be used to wash
a wide assortment of items when you don’t
have a full load. Also, when the upper rack
fi lls up with glasses and the lower rack is still
empty, you don’t have to wait anymore for
clean glasses.

STEMWARE HOLDER/CUPSHELF not
available on all models.

Loading the Bottom Rack

Features and appearance of racks and
silverware basket as shown may vary
from your model.

The lower rack is best for plates, saucers,
bowls, and cookware. Large items should be
placed along the edge so they do not block
the spray arm rotation. For best results, place
bowls, casseroles, and sauce pans with soiled
surface facing down and toward the center.
Tilt slightly for better drainage.

Make sure tall items do not block spray arm
rotation.

Be sure pan handles do not protrude through
the bottom of the rack and block the spray
arm rotation.

10 place settings standard loading pattern.

12 place settings standard loading pattern.

8

PREPARING AND LOADING DISHES

Loading the Silverware Basket

CAUTION

Load sharp items (knives, skewers, etc.)
pointing down.

Failure to do so may result in injury.

Features and appearance of racks and
silverware basket as shown may vary
from your model.

Load the silverware basket while it is in the
bottom rack or take the basket out for loading
on a counter or table.

For baskets with lids small items like baby
bottle caps, jar lids, corn cob holders, etc.,
can be placed in a covered section. Close the
cover to hold small items in place.

Adding a Dish

To add or remove items after wash cycle
starts:

• Unlatch door and wait a few seconds
until wash action stops before opening.

• Add the item, place the door in an
almost closed position, and wait a few
seconds to allow cold air to slowly
expand inside dishwasher.

• Close door fi rmly to latch and resume
cycle.

Use suggested loading patterns, as shown, to
increase washability of the silverware.

Be sure nothing protrudes through bottom of
basket or rack to block the spray arm.

Do not mix silver and stainless to avoid
damaging the silver fi nish.

When covers are up, mix items in each
section of the basket with some pointing
up and some down to avoid nesting. Water
spray cannot reach nested items.

9

DISHWASHER DISPENSER & DETERGENTS

CAUTION

The use of industrial grade detergent can
damage the heating coil and other parts of
the dishwasher leading to damage to the
unit and surrounding property. Use only
household grade automatic dishwasher
detergents.

Filing the Detergent Dispenser

The detergent dispenser has two detergent
cups. The smaller one is for addition to the
pre-wash and the larger is for release to the
main wash.

• Use only fresh automatic dishwashing
detergent. Other detergents may cause
oversudsing.

• When using automatic dishwashing
detergent tablets or packets, use only one
tablet or packet, place in the main wash
cup and close.

• Add detergent just before starting cycle.

• Store detergent in a cool, dry location and
discard any that becomes moist or caked.

Detergent Usage Chart

Cycle Soft Water

(0-3 grains)

Medium Hard Water

(4-8 grains)

Cover

Main
Wash
Cup

Cover
Latch

Pre-Wash
Cup

If the cover is closed on the Main Wash Cup
open by pressing the Cover Latch.

How much Detergent to use

The amount of detergent to use depends
on the water hardness. Water hardness is
measured in grains per gallon. Using too little
detergent can result in poor cleaning and hard
water fi lming or spotting. Using too much
detergent in soft water can cause etching
to some glassware which is surface damage
that appears like a fi lm but cannot be wiped
off. Your local water company, water softener
company or county extension agent can tell
you the water hardness in your area.

Hard Water

(9-12 grains)

Very Hard Water

(Over 12 grains)

Heavy Clean
or

Normal Clean

Top Rack

Rinse Only

2 teaspoons

(each cup­1/4 full)

2 teaspoons

(Main Wash
cup-

1/4 full)

No Detergent No Detergent

5 teaspoons

(each cup- fi ll
to line above
“Regular”)

5 teaspoons

(each cup- fi ll
to line above
“Regular”)

8 teaspoons

(each cup­completely full)

8 teaspoons

(Main Wash
cup- completely
full)

No Detergent

Each Cup­Completely
Full (water

softener
recommended)

Main
Wash Cup­Completely Full

(water softener
recommended)

No Detergent

(water softener
recommended)

As a rule, use 1 teaspoon for each grain above 12. For very hard water, detergent alone
may not be enough and then a water softener is recommended to improve water quality and
dishwashing performance.

10

FACTORS AFFECTING PERFORMANCE

Rinse aid greatly improves drying and
reduces water spots.

Rinse Aid
Rinse aid greatly improves drying and

reduces water spots. With it water “sheets”

off dishes rather than forming water droplets
that cling and leave spots.

A dispenser, located next to the detergent cup,
automatically releases a measured amount of
rinse aid during the last rinse. If spotting and
poor drying are problems, increase the amount
of rinse aid dispensed by rotating the dial to a
higher number. The dial is located under the
dispenser cap. The indicator will be dark when
full and will show clear when it is time to refi ll.

To add liquid rinse aid, turn dispense cap 1/4
turn counterclockwise and lift out. Pour in
rinse aid until liquid touches the indicated fi ll
level. Replace cap.

Do not overfi ll since this can cause
oversudsing. Wipe up any spills with a damp
cloth.

The dispenser holds enough for 35 to 140
washes, depending on the setting selected.

Dispenser Opening Indicator

Water Pressure

The hot water line to the dishwasher must
provide water pressure between 20 and 120
psi.

Low Water pressure may occur when laundry
or showers are in operation. If you experience
poor wash performance you may need to
wait until water use is reduced before starting
dishwasher.

Water Temperature

Hot water is needed for best dishwashing and
drying results. Water entering the dishwasher
should be at least 120
satisfactory results.

To check the temperature of the water entering
the dishwasher:

• Turn on the hot water faucet nearest the
dishwasher for several minutes to clear
cool water from pipes.

• Hold a candy or meat thermometer in the
water stream to check the temperature.

• If temperature is below 120oF (49oC),
have a qualifi ed person raise the hot
water heater thermostat setting.

o

F (49oC) to give

IMPORTANT

Dispenser Cap

Adjustable Setting

Before starting a cycle, run hot water
to clear cool water from pipe.

Deselecting the AIR DRY option in
combination with the use of rinse aid will
enhance drying performance. The energy
required when AIR DRY is deselected
costs pennies per cycle. You may choose
to select the AIR DRY option; however
you will have items in your dish load that
will not be completely dry at the end of
the cycle.

11

CARE AND CLEANING

The fi lter is self-
cleaning. A glass trap located in the center of
the fi lter is designed to collect pieces of broken
glass, straws, bones and pits.

Spray Arm varies
by model

(2)

(3)

Glass Trap

(1)

Glass Trap Removal

To empty the glass trap:

1. Grasp the glass trap’s handle and rotate it
900 clockwise while pressing down on the
center of the wash arm.

2. Grab the spray arm in the center and lift
the spray arm and glass trap assembly up
and out form the dishwasher.

3. Tip the assembly over an appropriate
container and tap it to empty the glass
trap.
OR, separate the glass trap - pull
the glass trap handle toward you, then
up, then further toward you to slide it
away from the rest of the assembly;
empty it into an appropriate container;
then slide the glass trap back into the
assembly.

4. Place the assembly back into position,
press down on the arm at the center
and rotate the glass trap handle 90
counterclockwise being sure the glass
trap ends in the orientation shown in the
image above. To avoid damage to

your unit make sure the spray arm
and glass trap are fully snapped in
place.

0

WARNING

Burn Hazard

Allow heating element to cool before

Failure to do so can result in burns.

cleaning the interior.

Outer Door - Clean outer door with warm

soapy water and a dishcloth or sponge. Rinse
with clean water and a dry cloth. Do not use
harsh cleaners.

Inside - The inside of the dishwasher

including the fi lter is self-cleaning with normal
use. If needed, clean around the tub gasket
area with a damp cloth.
cleaning. A glass trap located in the center of
the fi lter is designed to collect pieces of broken
glass, straws, bones and pits.

The fi lter is self-

Overfi ll Protector- keeps dishwasher

from overfi lling and is located in the left front
corner of the tub.

• Clean occasionally with household cleaner
containing vinegar or bleach to dissolve
any buildup.

• Overfi ll Protector should move up and
down freely about one inch. If it does
not move, lift and clean underneath.

Care of Drain Air Gap

If a drain air gap was installed for your built-in
dishwasher, check to make sure it is clean so
the dishwasher will drain properly. A drain air
gap is usually mounted on counter top and can
be inspected by removing the cover. This is
not part of your dishwasher and is not covered
by warranty.

12

BEFORE YOU CALL

CAUTION

Property Damage Hazard

Freezing temperatures may cause water
lines to rupture. Be sure all supply lines to
and circulating lines within dishwasher are
protected.

Failure to do so could result in property
damage.

NOTE



Hard water may cause lime deposit buildup
on the interior of the dishwasher. For
cleaning instructions see “Removing Spots
and fi lm” section.

Winterizing

A dishwasher left in an unheated place should
be protected from freezing. Have a qualifi ed
person do the following:

To Disconnect Service:

1. Turn off electrical power to the
dishwasher at the supply source by
removing fuses or tripping circuit breaker.

2. Shut off water supply

3. Place a pan under the inlet valve.
Disconnect water line from inlet valve
and drain into pan.

4. Disconnect drain line from pump and
drain water into pan.

To Restore Service:

1. Direct water line discharge into a pan
and open the valve to fl ush the line.

2. Reconnect the water, drain, and
electrical power supply.

3. Turn on water and electrical power
supply.

4. Fill both detergent cups and run
dishwasher through a HEAVY CLEAN
cycle.

5. Check connections to make sure they
do not leak.

NOTE



See Installation Instructions for more details
on disconnecting and restoring service to
your dishwasher.

Before calling for service, review this
list. If may save you both time and
expense. This list includes common
experiences that are not the result of
defective workmanship or material in
your dishwasher.

Food Soils Left on Dishes

• Choose another cycle for longer washing
time.

• Check rack loading section for proper
loading-avoid nesting items.

• Do not overload the dishwasher (See
Preparing and Loading Dishes).

• Home water pressure may be too low­should be 20 to 120 pounds per square
inch (psi).

• Check incoming water temperature. It
should be about 120
Factors Affection Performance.)

• Check water hardness. For extremely
hard water, it may be necessary to install
a water softener. (See Detergent Chart).

• Use Fresh Detergent.

• Make sure items are not blocking the
spray arms, preventing them from
rotating.

• Check to verify that the glass trap is
maintained and installed properly (See

Care and Cleaning).

Dishes not Dry

• De-select the Air Dry option.

• Make sure the rinse aid dispenser is
fi lled.

• Increase the discharge setting of rinse
aid. (See Rinse Aid).

• Check the incoming water temperature.
Be sure it is at least 120

• Check for proper loading-avoid nesting
items.

o

F (49oC). (See

o

F (49oC).

13

BEFORE YOU CALL

• Cups with a concave bottom will collect
water. Load them at the far left and right
of the upper rack so they will be held in a
tilted position.

• Containers, bowls, pots/pans, and any
dishware with concave surfaces that can
collect water should be placed in the rack
facing or angled down so that water is
able to drain even from the lowest point.

• Plastic items may need to be towel dried.

Glassware/Flatware Spotted or Cloudy

• Check water hardness. For extremely
hard water, it may be necessary to install
a water softener. (See Detergent Chart).

• Water temperature may be low. Avoid
extremely low or high temperatures. (See
Factors Affecting Performance.

• Avoid overloading and improper loading.
(See Preparing and Loading Dishes).

• Use fresh detergent. Old detergent is
ineffective.

• Make sure rinse aid dispenser is fi lled.

• Check to see that proper amount of
detergent is being used for cycle selected.
(See Detergent Dispenser).

• Home water pressure may be too low-it
should be 20 to 120 pounds per square
inch (psi).

Dishware Chipped

• Load with care and do not overload. (See
Preparing and Loading Dishes).

• Place delicate items in top rack.

• Place glasses securely against pins and
not over pins.

• Load items so they are secure and don’t
jar loose when moving racks in and out.
Move racks in and out slowly.

• Make sure tall glasses and stemware will
clear top of tub when rack is pushed in.

• Fine antique china and crystal should be
hand-washed.

Dishware Stained or Discolored

• Tea and coffee can stain cups. Remove
the stains by hand washing in a solution
of 1/2 cup (120 ml) bleach and one quart
(1L) of warm water. Rinse thoroughly.

• Iron deposits in water can cause a yellow
or brown fi lm. A special fi lter installed
in the water supply line will correct this
problem. (See Removing Spots and Film).

• Aluminum utensils can leave gray/black
marks when they rub against other
items. Load Properly.

• Certain high acid foods can cause
discoloration of stainless steel and
plastics if allowed to sit for a long
period. Use the Rinse Only cycle
or rinse by hand if not operating
dishwasher at once.

• Mixing stainless steel and silver utensils
in silverware basket can cause pitting of
the stainless steel blades. Avoid mixing
stainless steel and silver.

Water in Bottom of Tub

• Water left in the tub bottom after the
cycle is complete is not normal. If
water remains in the bottom of the tub,
the dishwasher may not be draining
properly. (See Dishwasher Does not
Drain Properly).

Cycle Takes a Long Time

• The cycle may have been automatically
lengthened to reach key temperatures
due to some factor such as a cool water
supply or a large load of dishes.

• Delay Start option may have been
selected.

• Choose lower temperature options to
shorten the cycle.

• Cycles that are soil-sensing adjust
automatically to assure a good wash

- heavier soils will elicit a longer cycle
response.

Etching

• Using too much detergent especially in
soft or softened water causes damage
that looks like a fi lm but cannot be
removed.

• Adjust the amount of detergent based
on the water hardness. (Check Detergent
Chart).

• Lower the water temperature by selecting
one of the lower temperature options.

Detergent Left in Cups

• Detergent may be old. Discard and use
fresh detergent.

• Be sure the dish load doesn’t block spray
from entering the detergent cup.

• Check to see if cycle has been completed.

• Make sure items do not prevent the
detergent dispenser from opening.

14

BEFORE YOU CALL

Dishwasher Leaks

• Check that the door gasket is pressed
into its mounting channel, reaches to
the bottom of the tub and does not
extend beyond the end rib so as to
interfere with door closure.

• Spilled rinse aide can cause foam and
lead to overfl owing. Wipe up any spills
with a damp cloth.

• Check to see that the dishwasher is
level. (See Installation Instructions).

• Avoid oversudsing by using the correct
amount of detergent designed for
automatic dishwashers.

• Check to see that dishwasher is level.
(See Installation Instructions).

Normal Sounds You Will Hear

• Normal sounds include water fi ll, water
spray, draining and motor sounds.

• There is a noticeable change in sound
when the wash action switches between
the lower and middle spray arm. This
is normal since each spray arm has its
own sound.

• It is normal for the dishwasher to pause
(no sound) when the wash action is
switching between the lower and middle

spray arms.

Dishwasher Won’t Run

• Check to see if circuit breaker is tripped
or if a fuse is blown.

• Make sure water supply is turned on.

• Check to see if cycle is set correctly. (See
Operating Instructions).

• Is dishwasher set for Delay Start Option.

• Make sure door is closed and latched.

• Make sure START/PAUSE pad is pressed
after the cycle has been selected.

Dishwasher Won’t Fill

• Assure the water supply is turned on.

• Check that the overfi ll protector moves up
and down freely. (See Overfi ll Protector

section).

Dishwasher Does Not Drain Properly

• If unit is hooked up to a food waste
disposer, make sure the disposer is
empty.

• Assure the knockout plug has been
removed from inside the food waste
disposer inlet.

• Assure the drain hose isn’t kinked.

• Make sure cycle is complete, not in a
pause.

• Assure the glass trap is maintained and
installed properly assuring no clogs (See

Care and Cleaning).

Dishwasher has an Odor

• Soiled dishes left in dishwasher too long
can create an odor. Use Rinse Only
cycle.

• There will be a “new” smell when fi rst
installed. This is normal.

• Check to see if unit is draining properly.
(See Dishwasher Does Not Drain

Properly).

Stains on Tub Interior

• Washing large amounts of dishware with
tomato based soil can cause a pink/
orange appearance. This will not affect
performance and will gradually fade over
time. Pre-rinsing or using the Rinse Only
cycle will reduce the chance of staining.
Using no heat dry option will lessen

staining.

Opening the door during cycle

• If the dishwasher door is opened while
the unit is running, the START/PAUSE
pad must be pressed and the door shut
immediately to return the unit to the
selected cycle and option, this must
happen within 10 minutes for the unit to
continue the cycle.

Removing Spots and Film

Hard water can cause lime deposit buildup
on the interior of the dishwasher. Dishes
and glasses may also get spots and fi lm
for a number of reasons. (See Glassware/
Flatware Spotted or Cloudy section). To
remove buildup, and fi lm, clean using the

following instructions:

1. Load clean dishes and glasses in
normal manner. Do not load any
metal utensils or silverware.

2. Do not add detergent.

3. Select the NORMAL CLEAN cycle.
Close the door. Press START/PAUSE
pad.

4. Allow dishwasher to run until it starts
the third water fi ll (approximately 20
minutes).

5. Open the door, pour 2 cups of white
vinegar into the bottom of dishwasher.

6. Close the door and allow cycle to
fi nish.

15

MAJOR APPLIANCE WARRANTY

Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Crosley will pay all costs for repairing or replacing any parts of this appliance that prove to
be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.

Exclusions

This warranty does not cover the following:

1. Products with original serial numbers that have been removed, altered or cannot be readily determined.

2. Product that has been transferred from its original owner to another party or removed outside
the USA or Canada.

3. Rust on the interior or exterior of the unit.

4. Products purchased “as-is” are not covered by this warranty.

5. Food loss due to any refrigerator or freezer failures.

6. Products used in a commercial setting.

7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.

8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,
shelves, etc., which are not a part of the appliance when it is shipped from the factory.

10. Service calls to repair or replace appliance light bulbs, air fi lters, water fi lters, other
consumables, or knobs, handles, or other cosmetic parts.

11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry
trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12. Damages to the fi nish of appliance or home incurred during installation, including but not
limited to fl oors, cabinets, walls, etc.

13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Crosley parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fi res, or acts of God.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES ,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE
YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH
AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS
WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME ST ATES AND PROVINCES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRIT TEN WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

If You Need Service

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty
period should service be required. If service is performed, it is in your best interest to obtain
and keep all receipts. Service under this warranty must be obtained by contacting Crosley at the
addresses or phone numbers below.

This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by
Crosley Corporation. In Canada, your appliance is warranted by Crosley Canada Corp. Crosley
Corporation authorizes no person to change or add to any obligations under this warranty.
Obligations for service and parts under this warranty must be performed by Crosley Corporation
or an authorized service company. Product features or specifi cations as described or illustrated are
subject to change without notice.

FOR WARRANTY INFORMATION CONTACT:
USA 1.800.944.9044

Canada 1.866.213-9397

CROSLEY

www.Crosley.com

FOR PRODUCT INFORMATION CONTACT:

®

111 Cloverleaf Drive, Suite 200

Winston-Salem, NC 27103

336.761.1212

Crosley Corporation

16