Signal Types: Auto-detecting composite, S-Video, or component
Formats: NTSC 480i or PAL 576i
Color Depth: 24-bit, 16.7M colors
Features: Single-window scalable to full-screen, input switching
between QM and VIDEO inputs, time base correction, gamma
correction, line doubling, motion adaptive deinterlacing, reverse
3:2/2:2 pulldown
Audio
Hardware Features: Built-in microphone and amplified speakers,
stereo headphone output, internal volume control and audio mixer
QM IN: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Auto-detecting component (YP
S-Video (Y/C), or composite video with stereo program audio and
(2) mic channels;
Video Formats: NTSC 480i or PAL 576i
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length: 300 ft (aggregate distance from
QM origination)
VIDEO IN: (1) 8-wire RJ45 female, CAT5 balanced video input port
Signal Types: Auto-detecting component (YP
or composite;
Formats: NTSC 480i or PAL 576i
Input Impedance: 100 ohms balanced
Connects to any Crestron CAT5 balanced video source via CresCAT
cable, or TPMC-CH-IMC interface module (included) via 15 foot
“triamese” cable provided;
Maximum Cable Length: 500 feet for component, 750 feet for
composite/S-Video
BPR
),
BPR
), S-Video (Y/C),
®
17" Widescreen Tilt Touchpanel (continued)
AUDIO I/O: (1) 8-wire RJ45 female
Bidirectional CAT5 balanced audio port
Signal Types: Receives (1) balanced stereo audio signal, and
transmits (1) balanced stereo audio signal from internal microphone;
Maximum Input Level: 4 V
Maximum Output Level: 2 V
Input/Output Impedance: 600 ohms
Connects to any other Crestron CAT5 balanced audio port via
CresCAT cable, or TPMC-CH-IMC interface module (included) via
15 foot “triamese” cable provided;
Maximum Cable Length: 1000 feet
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Output Power: 12mW per channel
Minimum Impedance: 32 ohms
USB: (1) USB Type B female (reserved for future applications)
NET: (1) 4-pin 3.5mm detachable terminal block
Cresnet Slave Port, connects to Cresnet control network, or
TPMC-CH-IMC interface module (included) via 15 foot “triamese”
cable provided
LAN: (1) 8-wire RJ45 with 2 LED indicators
10BaseT/100BaseTX Ethernet port
Green LED indicates link status
Yellow LED indicates Ethernet activity
RS-232: (1) 6-pin RJ11 female
Computer console, touch output or mouse input port
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
G: (1) 6-32 screw, chassis ground lug
MEMORY EXPANSION: (1) Type II Compact Flash card slot for
Temperature: 41° to 113°F (5° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact injection-molded case, tilt screen with
adjustable tension, integral rear cover and cable strain relief in base
Screen Tilt: Adjustable 45 to 90 degrees
Dimensions
Height: 13.78 in (35.01 cm)
Width: 17.63 in (44.79 cm)
Depth: 12.40 in (31.50 cm)
Signal Types: Auto-detecting composite, S-Video, or component
Formats: NTSC 480i or PAL 576i
Color Depth: 24-bit, 16.7M colors
Features: Single-window scalable to full-screen, input switching
between QM and VIDEO inputs, time base correction, gamma
correction, line doubling, motion adaptive deinterlacing, reverse
3:2/2:2 pulldown
Audio
Hardware Features: Built-in microphone and amplified speakers,
stereo headphone output, internal volume control and audio mixer
QM IN: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Auto-detecting component (YP
composite video with stereo program audio and (2) mic channels;
Video Formats: NTSC 480i or PAL 576i
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length: 300 ft (aggregate distance from
QM origination)
VIDEO IN: (1) 8-wire RJ45 female, CAT5 balanced video input port
Signal Types: Auto-detecting component (YP
or composite;
Formats: NTSC 480i or PAL 576i
Input Impedance: 100 ohms balanced
Connects to any Crestron CAT5 balanced video source via CresCAT
cable, or TPMC-CH-IMC interface module (included) via 15 foot
“triamese” cable provided;
Maximum Cable Length: 500 feet for component, 750 feet for
composite/S-Video
AUDIO I/O: (1) 8-wire RJ45 female
Bidirectional CAT5 balanced audio port
Signal Types: Receives (1) balanced stereo audio signal, and
transmits (1) balanced stereo audio signal from internal microphone;
Maximum Input Level: 4 V
Maximum Output Level: 2 V
Input/Output Impedance: 600 ohms
RMS
RMS
TPS-15B using QuickMedia
tilt touchpanels
BPR
), S-Video (Y/C), or
BPR
), S-Video (Y/C),
®
15" Tilt Touchpanel (continued)
Connects to any other Crestron CAT5 balanced audio port via
CresCAT cable, or TPMC-CH-IMC interface module (included) via
15 foot “triamese” cable provided;
Maximum Cable Length: 1000 feet
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Output Power: 12mW per channel
Minimum Impedance: 32 ohms
USB: (1) USB Type B female (reserved for future applications)
NET: (1) 4-pin 3.5mm detachable terminal block
Cresnet Slave Port, connects to Cresnet control network, or
TPMC-CH-IMC interface module (included) via 15 foot “triamese”
cable provided
LAN: (1) 8-wire RJ45 with 2 LED indicators
10BaseT/100BaseTX Ethernet port
Green LED indicates link status
Yellow LED indicates Ethernet activity
RS-232: (1) 6-pin RJ11 female
Computer console, touch output or mouse input port
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
Temperature: 41° to 113°F (5° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact injection-molded case, tilt screen with
adjustable tension, integral rear cover and cable strain relief in base
Screen Tilt: Adjustable 45 to 90 degrees
Dimensions
Height: 13.68 in (34.75 cm)
Width: 14.94 in (37.95 cm)
Depth: 12.40 in (31.50 cm)
Weight
14.55 lbs (6.60 kg)
10
INCLUDED ACCESSORIES
TPMC-CH-IMC
CAT5 Balanced AV Interface Module + 15 ft triamese cable
(See TPMC-CH-IMC specifications for complete information)
Signal Types: Auto-detecting composite, S-Video, or component
Formats: NTSC 480i or PAL 576i
Color Depth: 24-bit, 16.7M colors
Features: Single-window scalable to full-screen, input switching
between QM and VIDEO inputs, time base correction, gamma
correction, line doubling, motion adaptive deinterlacing, reverse
3:2/2:2 pulldown
Audio
Hardware Features: Built-in microphone and amplified speakers,
stereo headphone output, internal volume control and audio mixer
QM IN: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Auto-detecting component (YP
composite video with stereo program audio and (2) mic channels;
Video Formats: NTSC 480i or PAL 576i
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length: 300 ft (aggregate distance from
QM origination)
VIDEO IN: (1) 8-wire RJ45 female
CAT5 balanced video input port
Signal Types: Auto-detecting component (YP
or composite;
Formats: NTSC 480i or PAL 576i
Input Impedance: 100 ohms balanced
Connects to any Crestron CAT5 balanced video source via CresCAT
cable, or TPMC-CH-IMC interface module (included) via 15 foot
“triamese” cable provided;
Maximum Cable Length: 500 feet for component, 750 feet for
composite/S-Video
TPS-12B using QuickMedia
tilt touchpanels
BPR
), S-Video (Y/C), or
BPR
), S-Video (Y/C),
®
12" Tilt Touchpanel (continued)
AUDIO I/O: (1) 8-wire RJ45 female
Bidirectional CAT5 balanced audio port
Signal Types: Receives (1) balanced stereo audio signal, and
transmits (1) balanced stereo audio signal from internal microphone;
Maximum Input Level: 4 V
Maximum Output Level: 2 V
Input/Output Impedance: 600 ohms
Connects to any other Crestron CAT5 balanced audio port via
CresCAT cable, or TPMC-CH-IMC interface module (included) via 15
foot “triamese” cable provided;
Maximum Cable Length: 1000 feet
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Output Power: 12mW per channel
Minimum Impedance: 32 ohms
USB: (1) USB Type B female (reserved for future applications)
NET: (1) 4-pin 3.5mm detachable terminal block
Cresnet Slave Port, connects to Cresnet control network, or
TPMC-CH-IMC interface module (included) via 15 foot
“triamese” cable provided
LAN: (1) 8-wire RJ45 with 2 LED indicators
10BaseT/100BaseTX Ethernet port
Green LED indicates link status
Yellow LED indicates Ethernet activity
RS-232: (1) 6-pin RJ11 female
Computer console, touch output or mouse input port
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
G: (1) 6-32 screw, chassis ground lug
MEMORY EXPANSION: (1) Type II Compact Flash card slot for
Temperature: 41° to 113°F (5° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact injection-molded case, tilt screen with
adjustable tension, integral rear cover and cable strain relief in base
Screen Tilt: Adjustable 45 to 90 degrees
Dimensions
Height: 12.15 in (30.86 cm)
Width: 12.85 in (32.64 cm)
Depth: 12.40 in (31.50 cm)
Weight
12.95 lbs (5.88 kg)
RMS
RMS
14
INCLUDED ACCESSORIES
TPMC-CH-IMC
CAT5 Balanced AV Interface Module + 15 ft triamese cable
(See TPMC-CH-IMC specifications for complete information)
Isys engine, 16-bit non-palette graphics; 65,536 colors; Synapse
image rendering algorithm; multi-mode objects, color key video
windowing
Video
Signal Types: Auto-detecting composite/S-Video
Formats: NTSC 480i or PAL 576i
Color Depth: 18-bit; 262,144 colors
Features: Single-window scalable to full-screen, time base
correction, gamma correction
Audio
Hardware Features: Built-in microphone with defeatable AGC,
built-in amplified stereo speakers, headphone output, internal
volume control and audio mixer
Audio Feedback (WAV): 8-bit PCM, mono, 8 kHz sampling rate
Amplification: 2 Watts per channel for built-in stereo speakers
Connectors
NET/VIDEO: (1) 10-pin RJ45 female, shielded
Connects to interface module via 15 foot “siamese” cable provided
Contains Cresnet data, 24 Volts DC power, ground, and video
signals
TPS-4000 in a CH CAT5 AV Distribution System
AUDIO: (1) 8-pin RJ45 female, shielded
Connects to interface module via 15 foot “siamese” cable provided
Contains stereo audio input and mic out signals
RS-232: (1) 6-pin RJ11 female
Serial connection to PC for loading screen files
Touchscreen output to PC or Telestrator
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Connects to stereo headphones (not included)
Output Power: 12mW
Minimum Impedance: 32 ohms
Power Requirements
22 Watts (0.92 Amp @ 24 Volts DC)
PW-2420RU power supply sold separately
Cresnet Power Usage: 22 Watts (0.92 Amp @ 24 Volts DC)
If power is applied to the 24VDC jack and the NET port
(on TPS-IMPC) simultaneously, power will be drawn from
whichever is highest.
Environmental
Temperature: 50° to 113°F (10° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact black/silver injection-molded case
Screen Tilt: Adjustable 30 to 80 degrees
Dimensions
Height: 10.03 in (25.48 cm)
Width: 10.96 in (27.83 cm)
Depth: 9.32 in (23.67 cm)
Isys engine, 16-bit non-palette graphics; 65,536 colors; Synapse
image rendering algorithm; multi-mode objects, color key video
windowing
Video
Signal Types: Auto-detecting composite/S-Video
Formats: NTSC 480i or PAL 576i
Color Depth: 18-bit; 262,144 colors
Features: Single-window scalable to full-screen, time base
correction, gamma correction
Audio
Hardware Features: Built-in microphone with defeatable AGC,
built-in amplified stereo speakers, headphone output, internal
volume control and audio mixer
Audio Feedback (WAV): 8-bit PCM, mono, 8 kHz sampling rate
Amplification: 2 Watts per channel for built-in stereo speakers
TPS-3000 in a CH CAT5 AV Distribution System
®
6.4" Tilt Touchpanel (continued)
tilt touchpanels
Connectors
NET/VIDEO: (1) 10-pin RJ45 female, shielded
Connects to interface module via 15 foot “siamese” cable provided
Contains Cresnet data, 24 Volts DC power, ground, and video
signals
AUDIO: (1) 8-pin RJ45 female, shielded
Connects to interface module via 15 foot “siamese” cable provided
Contains stereo audio input and mic out signals
RS-232: (1) 6-pin RJ11 female
Serial connection to PC for loading screen files
Touchscreen output to PC or Telestrator
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Connects to stereo headphones (not included)
Output Power: 12mW
Minimum Impedance: 32 ohms
Power Requirements
22 Watts (0.92 Amp @ 24 Volts DC)
PW-2420RU power supply sold separately
Cresnet Power Usage: 22 Watts (0.92 Amp @ 24 Volts DC)
If power is applied to the 24VDC jack and the NET port (on
TPS-IMPC) simultaneously, power will be drawn from whichever
is highest.
Environmental
Temperature: 50° to 113°F (10° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact black/silver injection-molded case
Screen Tilt: Adjustable 30 to 80 degrees
Dimensions
Height: 7.56 in (19.20 cm)
Width: 8.40 in (21.34 cm)
Depth: 7.27 in (18.47 cm)
Weight
3.44 lbs (1.56 kg)
20
INCLUDED ACCESSORIES
TPS-IMPC
Interface Module + 15 ft siamese cable
(See TPS-IMPC specifications for complete information)
Signal Types: RGB and auto-detecting composite, S-Video, or
component video
Formats: SDTV 480i (NTSC) & 576i (PAL), EDTV 480p & 576p,
HDTV 720p & 1080i; RGB(VGA) up to UXGA 1600 x 1200
Color Depth: 24-bit, 16.7M colors
Features: Dual-window each scalable to full-screen, time base
QM IN 1: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Dynamically configurable under system control as:
(1) RGB input with stereo program audio and (2) mic channels, or
(1) Auto-detecting component (YP
or composite video input with stereo program audio
and (2) mic channels;
RGB Format: RGBHV
RGB Input Resolution, Non-interlaced: 640 x 480 minimum to 1600
x 1200 maximum (60 Hz limit at 1600 x 1200);
Video/HDTV Formats: 480i (NTSC), 576i (PAL), 480p, 576p, 720p
and 1080i;
Horizontal Frequency: 15 to 100 kHz
Vertical Frequency: 50 to 85 Hz
Delay Skew Compensation: 0 - 22 nS
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length: 450 ft (aggregate distance from
QM origination)
QM IN 2: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Dynamically configurable under system control as:
(1) RGB input with stereo program audio and (2) mic channels, or
(1) Auto-detecting component (YP
or composite video input with stereo program audio
and (2) mic channels;
RGB Format: RGBHV
RGB Input Resolution, Non-interlaced: 640 x 480 minimum to 1600
x 1200 maximum (60 Hz limit at 1600 x 1200);
Video/HDTV Formats: 480i (NTSC), 576i (PAL), 480p, 576p, 720p
and 1080i;
Horizontal Frequency: 15 to 100 kHz
Vertical Frequency: 50 to 85 Hz
tilt touchpanels
Delay Skew Compensation: none
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length (Video/HDTV): 300 ft (aggregate distance
from QM origination);
Maximum Cable Length (RGB @ 60Hz): 216 ft for 640x480, 140 ft for
800x600, 84 ft for 1024x768, 70 ft for 1280x768, 30 ft for 1600x1200
(using CresCAT-QM or CresCAT-IM cable)
QM OUT 1: (1) 8-wire RJ45 female, QuickMedia output port
containing RGB (same as touchscreen), WAV file audio, and internal
microphone signals;
RGB Format: RGBHV
RGB Output Resolution, Non-interlaced: 1024 x 768 pixels @ 60Hz
Connects to QM input port of any QuickMedia device via
CresCAT-QM or CresCAT-IM cable
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Output Power: 12mW per channel
Minimum Impedance: 32 ohms
RS-232: (1) 6-pin RJ11 female
Computer console, touch output, or mouse/touch input port
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
LAN: (1) 8-wire RJ45 with 2 LED indicators
10BaseT/100BaseTX Ethernet port
Green LED indicates link status
Yellow LED indicates Ethernet activity
24VDC: (1) 2.1mm barrel DC power jack
Do not use
NET: (1) 4-pin 3.5mm detachable terminal block
Cresnet Slave Port, connects to Cresnet control network
USB: (2) USB Type A female
USB 1.1 ports for mouse or touchscreen input
GND: (1) 6-32 screw, chassis ground lug
MEMORY EXP.: (1) Type II Compact Flash card slot for
memory expansion
PC CARD A – B: (2) Type II PC Card slots
(reserved for future applications)
Power Requirements
Cresnet Power Usage: 75 Watts (3.13 Amps @ 24 Volts DC)
Note: The 24VDC power jack should not be used.
Environmental
Temperature: 41° to 113°F (5° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact black/silver injection-molded case, tilt
screen with adjustable tension, integral rear cover and cable strain
relief in base
Screen Tilt: Adjustable 45 to 90 degrees
Dimensions
Height: 14.17 in (36.00 cm)
Width: 14.94 in (37.95 cm)
Depth: 13.75 in (34.93 cm)
Weight
15.2 lbs (6.9 kg)
1
See Web site or contact Crestron for a current list of compatible devices.
2
One or more QuickMedia devices are required to facilitate the input and
output of audio, video, and RGB signals. See the “MediaManager” section
of this catalog or visit the Crestron Website for more information about
QuickMedia.
Signal Types: RGB and auto-detecting composite, S-Video, or
component video
Formats: SDTV 480i (NTSC) & 576i (PAL), EDTV 480p & 576p,
HDTV 720p & 1080i; RGB(VGA) up to UXGA 1600 x 1200
Color Depth: 24-bit, 16.7M colors
Features: Dual-window each scalable to full-screen, time base
QM IN 1: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Dynamically configurable under system control as:
(1) RGB input with stereo program audio and (2) mic channels, or
(1) Auto-detecting component (YP
or composite video input with stereo program audio
and (2) mic channels;
RGB Format: RGBHV
RGB Input Resolution, Non-interlaced: 640 x 480 minimum to 1600
x 1200 maximum (60 Hz limit at 1600 x 1200);
Video/HDTV Formats: 480i (NTSC), 576i (PAL), 480p, 576p, 720p
and 1080i;
Horizontal Frequency: 15 to 100 kHz
Vertical Frequency: 50 to 85 Hz
Delay Skew Compensation: 0 - 22 nS
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length: 450 ft (aggregate distance from
QM origination)
QM IN 2: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Dynamically configurable under system control as:
(1) RGB input with stereo program audio and (2) mic channels, or
(1) Auto-detecting component (YP
or composite video input with stereo program audio
and (2) mic channels
RGB Format: RGBHV
RGB Input Resolution, Non-interlaced: 640 x 480 minimum to 1600
x 1200 maximum (60 Hz limit at 1600 x 1200);
Video/HDTV Formats: 480i (NTSC), 576i (PAL), 480p, 576p, 720p
and 1080i;
Horizontal Frequency: 15 to 100 kHz
Vertical Frequency: 50 to 85 Hz
tilt touchpanels
Delay Skew Compensation: none
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length (Video/HDTV): 300 ft (aggregate distance
from QM origination);
Maximum Cable Length (RGB @ 60Hz): 216 ft for 640x480, 140 ft for
800x600, 84 ft for 1024x768, 70 ft for 1280x768, 30 ft for 1600x1200
(using CresCAT-QM or CresCAT-IM cable)
QM OUT 1: (1) 8-wire RJ45 female, QuickMedia output port
containing RGB (same as touchscreen), WAV file audio, and internal
microphone signals;
RGB Format: RGBHV
RGB Output Resolution, Non-interlaced: 800 x 600 pixels @ 60Hz
Connects to QM input port of any QuickMedia device via
CresCAT-QM or CresCAT-IM cable
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Output Power: 12mW per channel
Minimum Impedance: 32 ohms
RS-232: (1) 6-pin RJ11 female
Computer console, touch output, or mouse/touch input port
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
LAN: (1) 8-wire RJ45 with 2 LED indicators
10BaseT/100BaseTX Ethernet port
Green LED indicates link status
Yellow LED indicates Ethernet activity
24VDC: (1) 2.1mm barrel DC power jack
24V DC power input (power supply sold separately)
NET: (1) 4-pin 3.5mm detachable terminal block
Cresnet Slave Port, connects to Cresnet control network
USB: (2) USB Type A female
USB 1.1 ports for mouse or touchscreen input
GND: (1) 6-32 screw, chassis ground lug
MEMORY EXP.: (1) Type II Compact Flash card slot for
memory expansion
PC CARD A – B: (2) Type II PC Card slots
(reserved for future applications)
Power Requirements
24VDC: 50 Watts (2.08 Amps) @ 24 Volts DC
(PW-2420RU power supply sold separately)
Cresnet Power Usage: 50 Watts (2.08 Amps @ 24 Volts DC)
Note: Power should only be applied to the 24VDC power jack
OR the NET port, not both.
Environmental
Temperature: 41° to 113°F (5° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact black/silver injection-molded case, tilt
screen with adjustable tension, integral rear cover and cable strain
relief in base
Screen Tilt: Adjustable 45 to 90 degrees
Dimensions
Height: 12.45 in (31.63 cm)
Width: 12.85 in (32.64 cm)
Depth: 13.75 in (34.93 cm)
Weight
13.8 lbs (6.2 kg)
1
See Web site or contact Crestron for a current list of compatible devices.
2
One or more QuickMedia devices are required to facilitate the input and
output of audio, video, and RGB signals. See the “MediaManager” section
of this catalog or visit the Crestron Website for more information about
QuickMedia.
Wireless Ethernet capable using third-party 802.11 PC card
(Wired connections required for power, audio, video and RGB)
Video/RGB
Signal Types: RGB and auto-detecting composite, S-Video, or
component video
Formats: SDTV 480i (NTSC) & 576i (PAL), EDTV 480p & 576p,
HDTV 720p & 1080i; RGB(VGA) up to UXGA 1600 x 1200
Color Depth: 24-bit, 16.7M colors
Features: Dual-window each scalable to full-screen, time base
correction, gamma correction, line doubling, motion adaptive
deinterlacing, reverse 3:2/2:2 pulldown
Streaming/File Formats: MPEG4 and MJPEG via Axis Media
Control plus all formats supported by the embedded media
player applications
Audio
Hardware Features: Built-in microphone and biamplified speakers,
stereo headphone output, internal volume control and audio mixer
Streaming/File Formats: All formats supported by the embedded
media player applications
Audio Feedback (WAV): 8 & 16 bit PCM, mono & stereo,
8 – 44 kHz sampling rates
D-A / A-D Conversion (QM): Burr Brown 24-bit, 48 kHz
Amplification: Biamplified, mono, 5 Watts for high-frequency,
5 Watts for low-frequency
Buttons
tilt touchpanels
(4) Backlit “softkey” buttons, programmable
(1) Backlit hard reset button, reboots the touchpanel system
Connectors
QM IN 1: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Dynamically configurable under system control as:
(1) RGB input with stereo program audio and (2) mic channels, or
(1) Auto-detecting component (YP
or composite video input with stereo program audio
and (2) mic channels;
RGB Format: RGBHV
RGB Input Resolution, Non-interlaced: 640 x 480 minimum to 1600
x 1200 maximum (60 Hz limit at 1600 x 1200);
Video/HDTV Formats: 480i (NTSC), 576i (PAL), 480p, 576p, 720p
and 1080i;
Horizontal Frequency: 15 to 100 kHz
Vertical Frequency: 50 to 85 Hz
Delay Skew Compensation: 0 – 22 nS
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length: 450 ft (aggregate distance from
QM origination)
2
1
2
1
BPR
), S-Video (Y/C),
1
QM IN 2: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Dynamically configurable under system control as:
(1) RGB input with stereo program audio and (2) mic channels, or
(1) Auto-detecting component (YP
or composite video input with stereo program audio
and (2) mic channels;
RGB Format: RGBHV
RGB Input Resolution, Non-interlaced: 640 x 480 minimum to 1600
x 1200 maximum (60 Hz limit at 1600 x 1200);
Video/HDTV Formats: 480i (NTSC), 576i (PAL), 480p, 576p, 720p
and 1080i;
Horizontal Frequency: 15 to 100 kHz
Vertical Frequency: 50 to 85 Hz
Delay Skew Compensation: none
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length (Video/HDTV): 300 ft
(aggregate distance from QM origination);
Maximum Cable Length (RGB @ 60Hz): 216 ft for 640x480, 140 ft for
800x600, 84 ft for 1024x768, 70 ft for 1280x768, 30 ft for 1600x1200
(using CresCAT-QM or CresCAT-IM cable)
QM OUT 1: (1) 8-wire RJ45 female, QuickMedia output port
containing RGB output with stereo audio from internal PC and
(2) discrete channels from internal mic;
RGB Format: RGBHV
RGB Output Resolution, Non-interlaced: 1280 x 768 pixels @ 60 Hz
Connects to QM input port of any QuickMedia device via
CresCAT-QM or CresCAT-IM cable
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Output Power: 105 mW per channel
Minimum Impedance: 8 ohms
USB: (2) USB Type A female, USB 1.1 ports for mouse, keyboard,
and storage devices
RS-232: (1) 6-pin RJ11 female, computer console port
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
PC CARD A – B: (2) Type II PC Card slots for memory expansion,
project upload, and wireless NIC
ETHERNET: (1) 8-wire RJ45 with 2 LED indicators
10BaseT/100BaseTX Ethernet port
Green LED indicates network speed
Yellow LED indicates Ethernet activity
NET: (1) 4-pin 3.5mm detachable terminal block
Cresnet Slave Port (data only; 24V terminal not used)
Connects to Cresnet control network
PWR: (1) 4-pin DC power jack, 12.5V DC power input
(external power supply included)
GND: (1) 6-32 screw, chassis ground lug
Power Requirements
TPMC-17-QM: 8.4 Amps @ 12.5 Volts DC
External Power Supply (included): 2.2 Amps @ 100–250 Volts
AC, 50/60 Hz
Cresnet Power Usage: 0 Watt @ 24 Volts DC
Isys i/O™ 17" Tilt Touchpanel Media Center w/QuickMedia
Environmental
TPMC-17-QM in a QuickMedia system
Temperature: 50° to 113°F (10° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact black/silver injection-molded case with
integral rear cover and cable strain relief
Screen Tilt: Adjustable 45 to 90 degrees
Dimensions
Height: 14.17 in (35.99 cm)
Width: 17.63 in (44.77 cm)
Depth: 13.74 in (34.90 cm)
Weight
19.4 lbs (8.8 kg)
INCLUDED ACCESSORIES
PW-1280RU
Power Supply
1
See Web site or contact Crestron for a current list of compatible devices
and embedded applications. To ensure reliable performance, new device
drivers and applications are available only from Crestron through firmware
updates.
2
One or more QuickMedia devices are required to facilitate the input and
output of audio, video, and RGB signals. See the “MediaManager” section
of this catalog or visit the Crestron Website for more information about
QuickMedia.
Wireless Ethernet capable using third-party 802.11 PC card
(Wired connections required for power, audio, video and RGB)
Video/RGB
Signal Types: RGB and auto-detecting composite, S-Video, or
component video
Formats: SDTV 480i (NTSC) & 576i (PAL), EDTV 480p & 576p,
HDTV 720p & 1080i; RGB(VGA) up to UXGA 1600 x 1200
Color Depth: 24-bit, 16.7M colors
Features: Dual-window each scalable to full-screen, time base
correction, gamma correction, line doubling, motion adaptive
deinterlacing, reverse 3:2/2:2 pulldown
Streaming/File Formats: MPEG4 and MJPEG via Axis Media
Control plus all formats supported by the embedded media player
applications
Audio
Hardware Features: Built-in microphone and biamplified speakers,
stereo headphone output, internal volume control and audio mixer
Streaming/File Formats: All formats supported by the embedded
media player applications
Audio Feedback (WAV): 8 & 16 bit PCM, mono & stereo,
8 – 44 kHz sampling rates
D-A / A-D Conversion (QM): Burr Brown 24-bit, 48 kHz
Amplification: Biamplified, mono, 5 Watts for high-frequency,
5 Watts for low-frequency
Buttons
tilt touchpanels
(4) Backlit “softkey” buttons, programmable
(1) Backlit hard reset button, reboots the touchpanel system
Connectors
QM IN 1: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Dynamically configurable under system control as:
(1) RGB (VGA) input with stereo program audio and (2) mic
channels, or
(1) Auto-detecting component (YP
composite video input with stereo program audio
and (2) mic channels;
RGB Format: RGBHV
RGB Input Resolution, Non-interlaced: 640 x 480 minimum to 1600
x 1200 maximum (60 Hz limit at 1600 x 1200);
Video/HDTV Formats: 480i (NTSC), 576i (PAL), 480p, 576p, 720p
and 1080i;
Horizontal Frequency: 15 to 100 kHz
Vertical Frequency: 50 to 85 Hz
Delay Skew Compensation: 0 – 22 nS
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length: 450 ft (aggregate distance from
QM origination)
2
1
2
1
BPR
), S-Video (Y/C), or
TM
15" Tilt Touchpanel Media Center w/QuickMediaTM(continued)
QM IN 2: (1) 8-wire RJ45 female, QuickMedia input port
Signal Types: Dynamically configurable under system control as:
(1) RGB (VGA) input with stereo program audio and (2) mic
channels, or
(1) Auto-detecting component (YP
1
composite video input with stereo program audio
and (2) mic channels;
RGB Format: RGBHV
RGB Input Resolution, Non-interlaced: 640 x 480 minimum to 1600
x 1200 maximum (60 Hz limit at 1600 x 1200);
Video/HDTV Formats: 480i (NTSC), 576i (PAL), 480p, 576p, 720p
and 1080i;
Horizontal Frequency: 15 to 100 kHz
Vertical Frequency: 50 to 85 Hz
Delay Skew Compensation: none
Connects to QM output port of a QM-TX or other QuickMedia device
via CresCAT-QM or CresCAT-IM cable;
Maximum Cable Length (Video/HDTV): 300 ft (aggregate distance
from QM origination);
Maximum Cable Length (RGB @ 60Hz): 216 ft for 640x480, 140 ft for
800x600, 84 ft for 1024x768, 70 ft for 1280x768, 30 ft for 1600x1200
(using CresCAT-QM or CresCAT-IM cable)
QM OUT 1: (1) 8-wire RJ45 female, QuickMedia output port
containing RGB output with stereo audio from internal PC and (2)
discrete channels from internal mic;
RGB Format: RGBHV
RGB Output Resolution, Non-interlaced: 1024 x 768 pixels @ 60 Hz
Connects to QM input port of any QuickMedia device via
CresCAT-QM or CresCAT-IM cable
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Output Power: 105 mW per channel
Minimum Impedance: 8 ohms
USB: (2) USB Type A female, USB 1.1 ports for mouse, keyboard,
and storage devices
RS-232: (1) 6-pin RJ11 female, computer console port
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
PC CARD A – B: (2) Type II PC Card slots for memory expansion,
project upload, and wireless NIC
ETHERNET: (1) 8-wire RJ45 with 2 LED indicators
10BaseT/100BaseTX Ethernet port
Green LED indicates network speed
Yellow LED indicates Ethernet activity
NET: (1) 4-pin 3.5mm detachable terminal block
Cresnet Slave Port (data only; 24V terminal not used)
Connects to Cresnet control network
PWR: (1) 4-pin DC power jack, 12.5V DC power input
(external power supply included)
Isys i/OTM15" Tilt Touchpanel Media Center w/QuickMedia
TPMC-15-QM in a QuickMedia system
Power Requirements
TPMC-15-QM: 8.4 Amps @ 12.5 Volts DC
External Power Supply (included): 2.2 Amps @ 100–250 Volts
AC, 50/60 Hz
Cresnet Power Usage: 0 Watt @ 24 Volts DC
Environmental
Temperature: 50° to 113°F (10° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact black/silver injection-molded case with
integral rear cover and cable strain relief
Screen Tilt: Adjustable 45 to 90 degrees
Dimensions
Height: 14.17 in (35.99 cm)
Width: 14.94 in (37.95 cm)
Depth: 13.74 in (34.90 cm)
Weight
15.8 lbs (7.1 kg)
INCLUDED ACCESSORIES
PW-1280RU
Power Supply
TM
TPMC-15-QM
tilt touchpanels
AVAILABLE ACCESSORIES
QM-TX
QuickMedia Transmitter
TPS/TPMC-CBL-T
Triamese Interface Cables
SMK-12/15/17
Swivel Mount Kit
1
See Web site or contact Crestron for a current list of compatible devices
and embedded applications. To ensure reliable performance, new device
drivers and applications are available only from Crestron through firmware
updates.
2
One or more QuickMedia devices are required to facilitate the input and
output of audio, video, and RGB signals. See the “MediaManager” section
of this catalog or visit the Crestron Website for more information about
QuickMedia.
Onboard PC applications for Web browsing, streaming media,
conferencing, VoIP, and remote desktop – no computer required!
High-performance dual-window HD video display
Built-in 10 watt biamplified speaker system and microphone
Crestron Home CAT5 AV connectivity
Secure high-speed Ethernet and Cresnet communications
Tiltcase housing with integral rear cover and cable strain relief
TPMC-17-CH using CAT5 AV Interface Module
2
SPECIFICATIONS
Touchscreen Display
Display Type: TFT Active matrix color LCD
Size: 17 inch (43.2 cm) diagonal widescreen
Aspect Ratio: 15:9 WXGA
Resolution: 1280 x 768 pixels
Brightness: 450 nits (cd/m
Contrast: 400:1
Color Depth: 24-bit, 16.7M colors
Illumination: Backlit fluorescent
Viewing Angle: ±88° horizontal, ±88° vertical
Touchscreen: Resistive membrane
Processor
VIA Eden
Memory
SDRAM: 512 MB
Flash: 512 MB
PC Card: Accepts up to (2) 4GB Type II PC Cards (not included)
Maximum Project Size: 190 MB
Operating System
Microsoft
Graphic Engine
Isys i/O engine, VIA Unichrome
graphics + 8-bit alpha channel transparency, 16.7 million colors,
Synapse image rendering algorithm, multi-mode objects, dynamic
menu objects, dynamic graphics, PNG translucency, full-motion
(60 fps) animation, transition effects, color key video windowing
Embedded Software Applications
Microsoft Internet Explorer w/Macromedia®Flash®plug-in,
Windows Media
MediaMarker
Runtime, DirectX®, Yahoo! Widgets, Adobe®Acrobat®Reader,
and viewers for MS Word, Excel, and PowerPoint
Streaming/File Formats: MPEG4 and MJPEG via Axis Media
Control plus all formats supported by the embedded media
player applications
Audio
Hardware Features: Built-in microphone and biamplified speakers,
stereo headphone output, internal volume control and audio mixer
Streaming/File Formats: All formats supported by the embedded
media player applications
Audio Feedback (WAV): 8 & 16 bit PCM, mono & stereo,
8 – 44 kHz sampling rates
Amplification: Biamplified, mono, 5 Watts for high-frequency,
5 Watts for low-frequency
Buttons
(4) Backlit “softkey” buttons, programmable
(1) Backlit hard reset button, reboots the touchpanel system
Connectors
CH VIDEO IN 1 – 2: (2) 8-wire RJ45 female
CAT5 balanced video input ports
Signal Types: Auto-detecting component (YP
composite video;
Formats: SDTV 480i (NTSC) & 576i (PAL), EDTV 480p & 576p,
HDTV 720p & 1080i;
Input Impedance: 100 ohms balanced
Connect to any Crestron CAT5 balanced video source(s) via
CresCAT cable, or TPMC-CH-IMC interface module (included) via
15 foot “triamese” cable provided;
Maximum Cable Length: 500 feet for component/HDTV, 750 feet for
composite/S-Video
CH AUDIO I/O: (1) 8-wire RJ45 female
tilt touchpanels
Bidirectional CAT5 balanced audio port
Signal Types: Receives (1) balanced stereo audio signal, and
transmits (1) balanced stereo audio signal from internal PC or
microphone (dynamically selectable);
Maximum Input Level: 4 V
Maximum Output Level: 2 V
Input/Output Impedance: 600 ohms
Connects to any other Crestron CAT5 balanced audio port via
CresCAT cable, or TPMC-CH-IMC interface module (included) via
15 foot “triamese” cable provided;
Maximum Cable Length: 1000 feet
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Output Power: 105 mW per channel
Minimum Impedance: 8 ohms
USB: (2) USB Type A female, USB 1.1 ports for mouse, keyboard,
and storage devices
RS-232: (1) 6-pin RJ11 female, computer console port
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
PC CARD A – B: (2) Type II PC Card slots for memory expansion,
project upload, and wireless NIC
ETHERNET: (1) 8-wire RJ45 with 2 LED indicators
10BaseT/100BaseTX Ethernet port
Green LED indicates network speed
Yellow LED indicates Ethernet activity
1
1
RMS
RMS
1
1
TM
17" Tilt Touchpanel Media Center w/CH CAT5 AV (continued)
BPR
), S-Video (Y/C), or
NET: (1) 4-pin 3.5mm detachable terminal block
Cresnet Slave Port (data only; 24V terminal not used)
Connects to Cresnet control network, or TPMC-CH-IMC interface
module (included) via 15 foot "triamese" cable provided
PWR: (1) 4-pin DC power jack, 12.5V DC power input
(external power supply included)
GND: (1) 6-32 screw, chassis ground lug
Power Requirements
TPMC-17-CH: 8.4 Amps @ 12.5 Volts DC
External Power Supply (included): 2.2 Amps @ 100-250
Volts AC, 50/60 Hz
Cresnet Power Usage: 0 Watt @ 24 Volts DC
Environmental
Temperature: 50° to 113°F (10° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact black/silver injection-molded case with
integral rear cover and cable strain relief
Screen Tilt: Adjustable 45 to 90 degrees
Dimensions
Height: 14.17 in (35.99 cm)
Width: 17.63 in (44.77 cm)
Depth: 13.74 in (34.90 cm)
Weight
19.4 lbs (8.8 kg)
INCLUDED ACCESSORIES
(See individual product specifications for complete information.)
TPMC-CH-IMC
CAT5 Balanced AV Interface Module + 15 ft triamese cable
PW-1280RU
Power Supply
1
See Web site or contact Crestron for a current list of compatible devices
and embedded applications. To ensure reliable performance, new device
drivers and applications are available only from Crestron through firmware
updates.
2
Additional CAT5 Balanced AV equipment is required to facilitate the input
of more than one external video signal. See the “Audio Video Distribution
and Surround Sound” section of this catalog or visit the Crestron Website
for more information about Crestron Home CAT5 Balanced AV.
Onboard PC applications for Web browsing, streaming media,
conferencing, VoIP, and remote desktop – no computer required!
High-performance dual-window HD video display
Built-in 10 watt biamplified speaker system and microphone
Crestron Home CAT5 AV connectivity
Secure high-speed Ethernet and Cresnet communications
Tiltcase housing with integral rear cover and cable strain relief
TPMC-15-CH using CAT5 AV Interface Module
2
SPECIFICATIONS
Touchscreen Display
Display Type: TFT Active matrix color LCD
Size: 15 inch (38.1 cm) diagonal
Aspect Ratio: 4:3 XGA
Resolution: 1024 x 768 pixels
Brightness: 350 nits (cd/m
Contrast: 700:1
Color Depth: 24-bit, 16.7M colors
Illumination: Backlit fluorescent
Viewing Angle: ±85° horizontal, ±85° vertical
Touchscreen: Resistive membrane
Processor
VIA Eden
Memory
SDRAM: 512 MB
Flash: 512 MB
PC Card: Accepts up to (2) 4GB Type II PC Cards (not included)
Maximum Project Size: 190 MB
Operating System
Microsoft
Graphic Engine
Isys i/O engine, VIA Unichrome
graphics + 8-bit alpha channel transparency, 16.7 million colors,
Synapse image rendering algorithm, multi-mode objects, dynamic
menu objects, dynamic graphics, PNG translucency, full-motion
(60 fps) animation, transition effects, color key video windowing
Embedded Software Applications
Microsoft Internet Explorer w/Macromedia_ Flash_ plug-in,
Windows Media
Crestron MediaMarker
Java˛ Runtime, DirectX
and viewers for MS Word, Excel, and PowerPoint
Streaming/File Formats: MPEG4 and MJPEG via Axis Media
Control plus all formats supported by the embedded media
player applications
Audio
Hardware Features: Built-in microphone and biamplified speakers,
stereo headphone output, internal volume control and audio mixer
Streaming/File Formats: All formats supported by the embedded
media player applications
Audio Feedback (WAV): 8 & 16 bit PCM, mono & stereo,
8 – 44 kHz sampling rates
Amplification: Biamplified, mono, 5 Watts for high-frequency,
5 Watts for low-frequency
Buttons
(4) Backlit “softkey” buttons, programmable
(1) Backlit hard reset button, reboots the touchpanel system
Connectors
CH VIDEO IN 1 – 2: (2) 8-wire RJ45 female
CAT5 balanced video input ports
Signal Types: Auto-detecting component (YP
composite video;
Formats: SDTV 480i (NTSC) & 576i (PAL), EDTV 480p & 576p, HDTV
720p & 1080i;
Input Impedance: 100 ohms balanced
Connect to any Crestron CAT5 balanced video source(s) via
CresCAT cable, or TPMC-CH-IMC interface module (included) via
15 foot “triamese” cable provided;
Maximum Cable Length: 500 feet for component/HDTV, 750 feet for
composite/S-Video
CH AUDIO I/O: (1) 8-wire RJ45 female
tilt touchpanels
Bidirectional CAT5 balanced audio port
Signal Types: Receives (1) balanced stereo audio signal, and
transmits (1) balanced stereo audio signal from internal PC or
microphone (dynamically selectable);
Maximum Input Level: 4 V
Maximum Output Level: 2 V
Input/Output Impedance: 600 ohms
Connects to any other Crestron CAT5 balanced audio port via
CresCAT cable, or TPMC-CH-IMC interface module (included) via
15 foot “triamese” cable provided;
Maximum Cable Length: 1000 feet
HEADPHONES: (1) 3.5 mm TRS mini phone jack
Output Power: 105 mW per channel
Minimum Impedance: 8 ohms
USB: (2) USB Type A female, USB 1.1 ports for mouse, keyboard,
and storage devices
RS-232: (1) 6-pin RJ11 female, computer console port
Bidirectional RS-232 up to 115.2k baud
Hardware and software handshaking support
PC CARD A – B: (2) Type II PC Card slots for memory expansion,
project upload, and wireless NIC
ETHERNET: (1) 8-wire RJ45 with 2 LED indicators
10BaseT/100BaseTX Ethernet port
Green LED indicates network speed
Yellow LED indicates Ethernet activity
1
1
RMS
RMS
1
1
TM
15" Tilt Touchpanel Media Center w/CH CAT5 AV (continued)
BPR
), S-Video (Y/C), or
NET: (1) 4-pin 3.5mm detachable terminal block
Cresnet Slave Port (data only; 24V terminal not used)
Connects to Cresnet control network, or TPMC-CH-IMC interface
module (included) via 15 foot “triamese” cable provided
PWR: (1) 4-pin DC power jack, 12.5V DC power input
(external power supply included)
GND: (1) 6-32 screw, chassis ground lug
Power Requirements
TPMC-15-CH: 8.4 Amps @ 12.5 Volts DC
External Power Supply (included): 2.2 Amps @ 100-250
Volts AC, 50/60 Hz
Cresnet Power Usage: 0 Watt @ 24 Volts DC
Environmental
Temperature: 50° to 113°F (10° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Construction: High impact black/silver injection-molded case with
integral rear cover and cable strain relief
Screen Tilt: Adjustable 45 to 90 degrees
Dimensions
Height: 14.17 in (35.99 cm)
Width: 14.94 in (37.95 cm)
Depth: 13.74 in (34.90 cm)
Weight
15.8 lbs (7.1 kg)
INCLUDED ACCESSORIES
(See individual product specifications for complete information.)
TPMC-CH-IMC
CAT5 Balanced AV Interface Module + 15 ft triamese cable
PW-1280RU
Power Supply
1
See Web site or contact Crestron for a current list of compatible devices
and embedded applications. To ensure reliable performance, new device
drivers and applications are available only from Crestron through firmware
updates.
2
Additional CAT5 Balanced AV equipment is required to facilitate the input
of more than one external video signal. See the “Audio Video Distribution
and Surround Sound” section of this catalog or visit the Crestron Website
for more information about Crestron Home CAT5 Balanced AV.
QM OUT: (1) 8-wire RJ45 female, QuickMedia output port
Connects to QM input port of touchpanel of other
QuickMedia device via CresCAT-QM or CresCAT-IM cable*
S
B, YPBPR, S-Video (Y/C),
R
, G/Y/Y, & B/COMP/PB)
P-P
for RGB and C of S-Video;
RMS
balanced, 2 V
P-P
for H and V Sync;
RMS
unbalanced
NET: (2) 4-pin 3.5mm detachable terminal blocks
Cresnet slave ports, paralleled
Connect to Cresnet control network
G: (1) 6-32 screw, chassis ground lug
LED Indicators
PWR: (green) Indicates DC power supplied from
Cresnet network
NET: (yellow) Indicates communication with Cresnet system
VIDEO ACT: (red) Indicates presence of a valid video
input signal
SETUP (rear): (red) Used for touch-settable ID (TSID)
Temperature: 41° to 104°F (5° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Black metal, 0.5U 19" rack mountable using optional ST-RMK
(sold separately)
Dimensions
Height: 1.80 in (4.57 cm)
Width: 7.07 in (17.96 cm)
Depth: 7.02 in (17.83 cm)
Weight
2.05 lbs (0.93 kg)
AVAILABLE ACCESSORIES
ST-RMK
Rack Mount Kit
*
For QuickMedia wiring use CresCAT-QM or CresCAT-IM cable;
the maximum aggregate cable length and delay skew between
any QM transmitter (origination point) and QM receiver (endpoint)
is 450 ft (137 m) and 22 nS.
out of view near the touchpanel, or mounted remotely
in the central equipment cabinet, the TPMC-CH-IMC
provides connections for Cresnet, bidirectional audio,
and (1) video input signal. The balanced CAT5 AV
outputs support cable runs up to 300 feet (observe
distance limitations based upon power consumption
for the touchpanel in use).
Additional interface modules may be purchased and
installed to facilitate connectivity for a single movable
touchpanel at multiple locations. The TPMC-CH-IMC
can also be used as a CAT5 balanced AV interface
for use with other Crestron CAT5 AV products.
SPECIFICATIONS
Connectors
NET: (1) 4-pin 3.5mm detachable terminal block
tilt touchpanels
Cresnet slave port, Connects to Cresnet control network
VIDEO COMP/Y/Y, C/Pb, Pr: (3) BNC female
Provides (1) composite, S-Video, or component video input
Input Impedance: 75 ohms
Input Level: 1 V
Maximum DC Offset: 1.5 Volts
series touchpanels that utilize Crestron Home®(CH)
CAT5 Balanced AV connectivity*. It mounts into a
2-gang electrical box and includes front panel
connections for a single “triamese” cable (provided
with the touchpanel or sold separately). Several
TPMC-CH-IMW wall plates may be installed to
facilitate connectivity for a single movable
touchpanel at multiple locations.
Wired as part of a complete Crestron Home
CAT5 AV distribution system, the TPMC-CH-IMW
requires just a single CresCAT-D cable, carrying
Cresnet, bidirectional audio, and (1) video signal
up to 500 feet within a single bundled cable (observe
distance limitations based upon power consumption
for the touchpanel in use). The TPMC-CH-IMW can
also be connected to conventional audio and coaxial
video sources.
SPECIFICATIONS
Connectors – Front Panel
NET: (1) 4-pin 3.5mm detachable terminal block
Pass-thru from rear NET port
AUDIO: (1) 8-pin RJ45 female
Bidirectional CAT5 balanced stereo audio port
Output Impedance: 100 ohms balanced
Maximum Output Level: 2 V
Input Impedance: Infinite (unbuffered pass-thru to rear AUDIO
OUT port)
VIDEO: (1) 8-pin RJ45 female
CAT5 balanced video output port
Output Impedance: 100 ohms balanced
Connectors – Rear Panel
NET: (1) 4-pin 5mm detachable terminal block
Cresnet slave port, Connects to Cresnet control network
VIDEO COMP/Y/Y, C/Pb, Pr: (1) 9-pin 3.5mm detachable
terminal block providing (1) composite, S-Video, or
component video input
Input Impedance: 100 ohms balanced (also accepts 75 ohm
unbalanced);
Input Level: 1 V
Maximum DC Offset: 1.5 Volts
Connects to any Crestron CAT5 Video Out port via CresCAT
cable, or a conventional coax video source
Maximum Input Level: 4 V
Connects to any Crestron CAT5 Audio port via CresCAT
cable, or a conventional audio source
AUDIO OUT: (1) 5-pin 3.5mm detachable terminal block
Balanced stereo line-level output (unbuffered pass-thru
from front AUDIO port);
Connects to any Crestron CAT5 Audio port via CresCAT
cable, or a conventional balanced audio input
LED Indicators
PWR: (green) Indicates DC power supplied from
Cresnet network
Temperature: 41° to 122°F (5° to 50°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
2-gang mountable in a standard electrical box (2.5 inch deep
minimum); includes black metal front panel Decora
requires Decora faceplate (provided by others)
Dimensions
Height: 4.11 in (10.44 cm)
Width: 3.50 in (8.89 cm)
Depth: 1.66 in (4.22 cm)
Weight
7.5 oz (0.21 kg)
*The TPMC-CH-IMW is not compatible with QuickMedia or 10-pin
The TPS-IMPC is an interface module that is included
as standard with every Isys TPS-3000 and TPS-4000
tilt touchpanel. Additional interface modules may be
purchased and installed to facilitate connectivity for a
single non-stationary touchpanel at multiple locations.
The interface module connects to the touchpanel
using a “siamese” interface cable (included with the
touchpanel or sold separately). Installed neatly out
of view near the touchpanel, the interface module
provides all of the conventional connections for
power, Cresnet, audio, and video signals.
SPECIFICATIONS
Connectors
NET: (1) 4-pin 5mm detachable terminal block
Connects to Cresnet control network
24VDC: (1) 24 Volt DC power jack (PW-2420RU power
supply optional, sold separately);
Powers touchpanel and module in lieu of Cresnet power
NET/VIDEO TO PANEL: (1) 10-pin RJ45 female, shielded
Connects to touchpanel via “siamese” cable (included
with touchpanel);
Contains Cresnet data, 24 Volts DC power, ground, and
video signals
AUDIO TO PANEL: (1) 8-pin RJ45 female, shielded
Connects to touchpanel via “siamese” cable (included
with touchpanel);
Contains stereo audio input and mic out signals
MIC OUT: (1) 3-pin 3.5mm detachable terminal block
Balanced/unbalanced mono line-level output
Output Impedance: 600 ohms balanced, 300 ohms
unbalanced;
Maximum Output Level: 2 V
NTSC/PAL VIDEO (Coaxial): (2) BNC female
Comprises (1) composite or S-Video input
Input Impedance: 75 ohms
NTSC/PAL VIDEO (Balanced): (1) 6-pin 3.5mm detachable
terminal block;
Comprises (1) composite or S-Video input, balanced
Connects to any Crestron CAT5 balanced video source
Input Impedance: 100 ohms
RMS
balanced, 2 V
RMS
balanced, 1 V
RMS
unbalanced
RMS
unbalanced
DIP Switches
BAL/COAX: Selects between balanced or coaxial
video inputs
Power Requirements
24VDC: <1 Watt @ 24 Volts DC – not including touchpanel
(PW-2420RU power supply sold separately)
Cresnet Power Usage: <1 Watt @ 24 Volts DC – not
including touchpanel
Note: If power is applied to the 24VDC jack and the NET port
simultaneously, power will be drawn from whichever is
highest.
Environmental
Temperature: 41° to 113°F (5° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Black metal, surface mount box with (2) integral
mounting flanges
Dimensions
Height: 1.25 in (3.18 cm)
Width: 5.82 in (14.79 cm)
Depth: 3.50 in (8.89 cm)
installed to facilitate connectivity for a single non-
stationary touchpanel at multiple locations.
The interface module connects to the touchpanel
using a 10-pin interface cable (included with the
touchpanel or sold separately). Installed neatly out
of view near the touchpanel, the interface module
provides all of the conventional connections for
power, Cresnet, and video signals.
SPECIFICATIONS
Connectors
NET: (1) 4-pin 5mm detachable terminal block
Connects to Cresnet control network
24VDC: (1) 24 Volt DC power jack
(PW-2420RU power supply optional, sold separately)
Powers touchpanel and module in lieu of Cresnet power
NET/VIDEO TO PANEL: (1) 10-pin RJ45 female, shielded
Connects to touchpanel via “siamese” cable (included
tilt touchpanels
with touchpanel);
Contains Cresnet data, 24 Volts DC power, ground, and
video signals
NTSC/PAL VIDEO (Coaxial): (2) BNC female
Comprises (1) composite or S-Video input
Input Impedance: 75 ohms
NTSC/PAL VIDEO (Balanced): (1) 6-pin 3.5mm detachable
terminal block;
Comprises (1) composite or S-Video input, balanced
Input Impedance: 100 ohms
Connects to any Crestron CAT5 balanced video source
DIP Switches
BAL/COAX: Selects between balanced or coaxial
video inputs
Power Requirements
24VDC: <1 Watt @ 24 Volts DC – not including touchpanel
(PW-2420RU power supply sold separately)
Cresnet Power Usage: <1 Watt @ 24 Volts DC – not
including touchpanel
If power is applied to the 24VDC jack and the NET port
simultaneously, power will be drawn from whichever is
highest.
®
Interface Module without Audio
Environmental
Temperature: 41° to 113°F (5° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Black metal, surface mount box with (2) integral
mounting flanges
Dimensions
Height: 1.25 in (3.18 cm)
Width: 5.82 in (14.79 cm)
Depth: 3.50 in (8.89 cm)
The TPS-IMW is a wall plate version of the TPS-IMPC
interface module, providing a flush wall plate connection
for any Isys TPS-3000 or TPS-4000 tilt touchpanel.
The TPS-IMW mounts into a 2-gang electrical box
(2.5" minimum depth) and includes front panel RJ45
connections for the siamese type cable (provided with
the touchpanel or sold separately). Several interface
module wall plates may be installed to facilitate
touchpanel connectivity at multiple locations.
SPECIFICATIONS
Connectors – Front Panel
NET/VIDEO: (1) 10-pin RJ45 female, shielded
Connects to touchpanel via “siamese” cable (included
with touchpanel);
Contains Cresnet data, 24 Volts DC power, ground, and
video signals
AUDIO: (1) 8-pin RJ45 female, shielded
Connects to touchpanel via “siamese” cable (included
with touchpanel);
Contains stereo audio input and mic out signals
Connectors – Rear Panel
NET: (1) 4-pin 5mm detachable terminal block
Connects to Cresnet control network
TPS-4000 tilt touchpanel whenever the touchpanel’s
built-in microphone and speakers are not being used.
The TPS-4500IMW mounts into a single-gang
electrical box (2.5" minimum depth) and includes one
front panel RJ45 connection for the 10-pin cable that
connects to the touchpanel (provided with the
touchpanel or sold separately). Several interface
module wall plates may be installed to facilitate
touchpanel connectivity at multiple locations.
SPECIFICATIONS
Connectors – Front Panel
NET/VIDEO: (1) 10-pin RJ45 female, shielded
Connects to touchpanel via “siamese” cable (included
with touchpanel);
Contains Cresnet data, 24 Volts DC power, ground, and
video signals
Connectors – Rear Panel
NET: (1) 4-pin 5mm detachable terminal block
Connects to Cresnet control network
COMP/Y: (1) 4-pin 3.5mm detachable terminal block
tilt touchpanels
comprising (1) composite or ‘Y’ of (1) S-Video input, balanced
or unbalanced;
Input Impedance: 100 ohms balanced, 75 ohms unbalanced
It is used only for loading touchpanel files, updating
firmware, and configuring the touchpanel prior to
operation. The ST-PK may also be used to update
firmware and adjust the digital audio signal processing
in Crestron’s 7.1 surround sound processors and
room solution boxes.
SPECIFICATIONS
Cables
3.5mm to RJ11 Cable Assembly (CNSP-585):
Provides connection between a SmarTouch wireless
touchpanel and the control processor via a RJ11 Cresnet
port; may require an additional CNRJ11 , ST-CNB, or
C2N-HBLOCK accessory.
RJ11-to-RJ11 Cable plus RJ11-to-DB9F Adapter
(STCP-502):
Provides connection between an Isys touchpanel,
surround processor, or room solution box RS-232 port and
PC COM port.