Crestron TMK-6X-DSW & WMKT-6X-DSW
Trim Ring Kits for the TPS-6X-DSW
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2009 Crestron Electronics, Inc.
Crestron TMK/WMKT-6X-DSW Trim Ring Mount Kits for the TPS-6X-DSW
Contents
Trim Ring Mount Kits for theTPS-6X-DSW:
TMK-6X-DSW & WMKT-6X-DSW
Introduction ...............................................................................................................................1
Setup..........................................................................................................................................2
Supplied Hardware......................................................................................................2
Installation...................................................................................................................4
Resources.................................................................................................................................10
Industry Compliance .................................................................................................10
Reference Documents................................................................................................10
Further Inquiries........................................................................................................10
Future Updates ..........................................................................................................10
Return and Warranty Policies..................................................................................................11
Merchandise Returns / Repair Service ......................................................................11
CRESTRON Limited Warranty.................................................................................11
1
Installation Guide – DOC. 6780A Contents • i
Crestron TMK/WMKT-6X-DSW Trim Ring Mount Kits for the TPS-6X-DSW
Trim Ring Mount Kits
for theTPS-6X-DSW:
TMK-6X-DSW & WMKT-6X-DSW
Introduction
These Trim Ring Mount Kits are the preferred method of mounting the Crestron®
TPS-6X-DSW Wall Mount Docking Station when a finished appearance within a
neatly trimmed cutout is required. This application is perfect for wallpapering.
NOTE: If mounting into a material other than drywall (for example, wood lectern,
concrete, or rock) use the cutout template, available in the post-construction kit
WMKT-6X-DSW. For concrete and rock mounting material, allow for proper
ventilation before mounting the TPS-6X-DSW.
There are two Trim Ring Mount Kits. The TMK-6X-DSW is a pre-construction
accessory. Pre-construction refers to framed walls prior to hanging drywall. This
accessory must be used with either the Pre-Construction Mount Kit (PMK-6X-DSW)
or Wall Mount Back Box (BB-6X-DSW).
The WMKT-6X-DSW is a post-construction kit. Post-construction refers to framed
walls with drywall hung. This accessory is designed with a mounting plate so that it
can be placed anywhere on a wall without the support of a stud. The mounting plate
is also ideal for installing the TPS-6X-DSW in a lectern.
NOTE: Since the TPS-6X-DSW contains moving parts, mounting to a stud offers
more support and is therefore highly recommended. Although Crestron offers the
post-construction WMKM-6X-DSW mounting option, a mounting option that is
secured to a stud, such as the BB-6X-DSW or PMK-6X-DSW is highly
recommended.
NOTE: If necessary, consult the latest revision of the TPS-6X-DSW Operations and
Installation Guide (Doc. 6708) for a complete list of mounting options. The
document is available from the Crestron website (
Installation Guide – DOC. 6780A Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW • 1
http://www.crestron.com/manuals).
Trim Ring Mount Kits for the TPS-6X-DSW Crestron TMK/WMKT-6X-DSW
Setup
Supplied Hardware
The TMK-6X-DSW consists of a metal trim ring that attaches to the BB-6X-DSW or
PMK-6X-DSW. The WMKT-6X-DSW consists of the trim ring found in the
TMK-6X-DSW as well as a mounting plate, cutout template and mounting screws.
The mounting plate provides the necessary support for post-construction
applications. An overlay cutout template (4506370) is supplied which is similar to a
frame, the inner area of the frame is the shape of the required opening. Remove the
center of the frame in order to use the template, refer to the illustration on page 3.
Supplied Hardware for the TMK-6X-DSW and WMKT-6X-DSW
DESCRIPTION PART NUMBER QUANTITY
Metal, Plate, Trim Ring 2022808 1
Metal, Plate, Mounting
(WMKT-6X-DSW only)
Screw, #06-32 x 1 1/2”, Pan, Phil
(WMKT-6X-DSW only)
Overlay, Template, Wall Cutout
(WMKT-6X-DSW Only)
2022811 1
2007254 4
4506370 1
The dimensions of the TMK-6X-DSW and WMKT-6X-DSW are shown below and
on the next page.
Dimensional Drawing – Trim Ring
9.28 in
(23.58 cm)
6.39 in
(16.23 cm)
0.52 in
(1.33 cm)
1.04 in
(26.27 cm )
4.00 in
(10.16 cm)
2.23 in
(5.66 cm )
2 • Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW Installation Guide – DOC. 6780A
Crestron TMK/WMKT-6X-DSW Trim Ring Mount Kits for the TPS-6X-DSW
Dimensional Drawing – Mounting Plate
10.31 in
8.16 in
(20.73 cm)
(16.13 cm)
6. 35 in
(26.19 cm)
8.00 in
(20.32 cm)
0.06 in
(0.16 cm)
Drywall Cutout Template and Dimensions (supplied with WMKT-6X-DSW only
9 1/16 in
(230 mm )
7 11/16 in
(196 mm )
6 1/8 i n
(156 mm )
6 9/16 in
(167 mm )
Installation Guide – DOC. 6780A Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW • 3
Trim Ring Mount Kits for the TPS-6X-DSW Crestron TMK/WMKT-6X-DSW
Installation
This section provides an installation procedure for each Trim Ring Mount Kit. The
“TMK-6X-DSW Procedure” starts below and the “WMKT-6X-DSW Procedure”
starts on page 6. Be sure to review each procedure before starting.
TMK-6X-DSW Procedure
This section provides the necessary steps for the assembly of the TMK-6X-DSW
with either the BB-6X-DSW or PMK-6X-DSW. It is assumed that the BB-6X-DSW
or PMK-6X-DSW has been secured to the stud according to the instructions in the
latest revisions of their Installation Guides (Doc. 6728 and Doc. 6778 respectively).
It is also assumed that drywall is in place and a cutout for the TPS-6X-DSW is made
in the drywall.
Complete the steps in the order provided. The only tool required and not supplied is
a level.
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the TPS-6X-DSW for heat dissipation.
NOTE: When installing into the PMK-6X-DSW, verify that the 18 AWG bus wire
securing the cables for the wall mount docking station remains attached.
1. Verify that the cutout in the drywall is as level as possible.
2. Insert the symmetrical trim ring into the opening, as shown in the
illustration below.
Insert Trim Ring into Opening
DRYWALL
IMPORTANT
MAKE DRYW ALL CUTOUT
AS LEVEL AND CLEAN AS
POSSIBLE. THE TR IM RIN G
ONLY A LLOW S M I NOR
ADJU STMENTS OF THE
TPS-6X-DSW.
TRIM RING
(2022808 )
NOTE: The required PMK-6X-DSW or BB-6X-DSW is not shown in the
illustration above.
4 • Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW Installation Guide – DOC. 6780A
Crestron TMK/WMKT-6X-DSW Trim Ring Mount Kits for the TPS-6X-DSW
3. When the trim ring is in position, bend the top two flanges of the ring
upward and the bottom two flanges downward.
• If mounting into the PMK-6X-DSW, bend the flanges approximately
90 degrees.
• If mounting into the BB-6X-DSW, bend the flanges back as far as they
can go.
4. Run the necessary cables for the TPX-6X-DSW and secure them behind the
drywall.
5. The wall mount docking station can be installed using the four tapped holes
in the PMK-6X-DSW or BB-6X-DSW. Refer to the latest revision of the
TPS-6X-DSW Operations and Installation Guide (Doc. 6708) for details.
Refer also to the comprehensive illustration below.
TPS-6X-DSW Mounting Using TMK-6X-DSW – Exploded View
PMK- 6X-DSW
DRYWALL
TPS-6X-DSW
TRIM RING
(2022808 )
Installation Guide – DOC. 6780A Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW • 5
Trim Ring Mount Kits for the TPS-6X-DSW Crestron TMK/WMKT-6X-DSW
WMKT-6X-DSW Procedure
This section provides the necessary steps for the assembly and installation of the
WMKT-6X-DSW into a wall. Review the procedure and complete the steps in the
order provided. The only tools or materials required and not supplied are a drywall
saw or equivalent and a level.
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the TPS-6X-DSW for heat dissipation.
1. Locate an area on the wall that is free of miscellaneous wiring and
studs.
2. Make a small hole near the middle of the designated site; verify that the
location is suitable.
NOTE: Make the cutout as level and smooth as possible. The mounting plate allows
for only minor leveling adjustments. If a larger cutout is made accidentally, consider
purchasing the Crestron Mud Mount Kit, MMK-6X-DSW. Together with the
mounting plate supplied with t he WM KT-6X-DSW, it provides a cost-effective
means of correction. Essentially, the combination of these two kits makes up the
Crestron Mud Mount Kit for the wall, WMKM-6X-DSW. Simply follow the
“WMKM-6X-DSW Procedure” in the latest revision of the Mud Mount Kits
Installation Guide (Doc. 6779).
3. Use the drywall saw or equivalent, the level and the provided cutout
template to produce a level and accurate cutout in the drywall.
4. Insert the trim ring into the opening, as shown in the illustration on the
following page.
6 • Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW Installation Guide – DOC. 6780A
Crestron TMK/WMKT-6X-DSW Trim Ring Mount Kits for the TPS-6X-DSW
Insert Trim Ring into Opening
DRYWALL
MOUNTING PLATE
(2022811)
TRIM RING
(2022808)
IMPORTANT
MAKE DRYWALL
CUTOUT AS LEVEL AND
CLEAN AS POSSIBLE.
THE TRIM R I N G ON LY
ALLOWS MINOR
ADJUSTMENTS OF THE
TPS-6X- D SW.
5. Carefully pass the mounting plate through the opening and hold it
against the interior surface of the drywall.
6. When the mounting plate is in position, bend the top two flanges of the
trim ring upward (approximately 90 degrees) and the bottom two
flanges downward (approximately 90 degrees). Refer to the illustration
on the following page.
NOTE: The mounting plate will have a slight play; this is normal. It allows for
minor adjustments to the TPS-6X-DSW during installation.
Installation Guide – DOC. 6780A Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW • 7
Trim Ring Mount Kits for the TPS-6X-DSW Crestron TMK/WMKT-6X-DSW
Bend Flanges – 1 of 4 Flanges Bent
BACK OF DRYWALL
7. Run the necessary cables for the TPS-6X-DSW and secure them behind
the drywall.
8. The wall mount docking station can be installed using the four tapped
holes in the mounting plate. Refer to the latest revision of the
TPS-6X-DSW Operations and Installation Guide (Doc. 6708) for
details. Refer also to the comprehensive illustration on the following
page.
8 • Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW Installation Guide – DOC. 6780A
Crestron TMK/WMKT-6X-DSW Trim Ring Mount Kits for the TPS-6X-DSW
TPS-6X-DSW Mounting Using WMKT-6X-DSW – Exploded View
TPS-6X-DS W
DRYWALL
TRIM RING
(2022808 )
MOUNTING PLATE
(2022811 )
SCREWS (4) #06-32 1 1/2"
PAN HE AD (2007254 )
Installation Guide – DOC. 6780A Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW • 9
Trim Ring Mount Kits for the TPS-6X-DSW Crestron TMK/WMKT-6X-DSW
Resources
Industry Compliance
As of the date of manufacture, the TMK-6X-DSW and WMKT- 6 X- DS W have been
tested and found to comply with specifications for CE marking.
Reference Documents
The latest version of all documents mentioned within the guide can be obtained from
the Crestron website (
product manuals arranged in alphabetical order by model number.
List of Related Reference Documents
www.crestron.com/manuals). This link will provide a list of
DOCUMENT TITLE
BB-6X-DSW Pre-Construction Wall Mount Back Box for TPS-6X-DSW
MMK-6X-DSW and WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW
PMK-6X-DSW Pre-Construction Mounting Kit for the TPS-6X-DSW
TPS-6X-DSW Wall Mount Docking Assembly for TPS-6X
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling Crestron at 1-888-CRESTRON [1-888-273-7876].
You can also log onto the online help section of the Crestron website
www.crestron.com/onlinehelp) to ask questions about Crestron products. First-time
(
users will need to establish a user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features and extends the capabilities of
the TMK-6X-DSW and WMKT-6X-DSW, additional information may be made
available as manual updates. These updates are solely electronic and serve as
intermediary supplements prior to the release of a complete technical documentation
revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
10 • Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW Installation Guide – DOC. 6780A
Crestron TMK/WMKT-6X-DSW Trim Ring Mount Kits for the TPS-6X-DSW
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying
the nature of the problem, name and phone number of contact person, RMA number and
return address.
2. Products may be returned for credit, exchange or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with
RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect
or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its
sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any
products returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in mat erial s
and workmanship under normal use for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical
parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and
overlay components are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON
dealer. Purchasers should inquire of the dealer regard ing the nature and extent of the dealer's warranty, if
any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a
third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are
limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.
Trademark Information
All brand names, product names and trademarks are the sole property of their respective owners. Windows is a registered trademark
of Microsoft Corporation. Windows95/98/Me/XP/Vista and WindowsNT/2000 are trademarks of Microsoft Corporation.
Installation Guide – DOC. 6780A Trim Ring Mount Kits for the TPS-6X-DSW: TMK/WMKT-6X-DSW • 11
Crestron Electronics, Inc. Installation Guide – DOC. 6780A
15 Volvo Drive Rockleigh, NJ 07647 (2023088)
Tel: 888.CRESTRON 01.09
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Loading...