Operations & Installation Guide – DOC. 6706A Contents • i
Crestron CEN-RFGW-EX infiNET EX™ Gateway
infiNET EX™ Gateway:
CEN-RFGW-EX
Introduction
The CEN-RFGW-EX gateway is an RF wireless transceiver designed for
use with the MLX-2 infiNET EX™ LCD Handheld Remote and other
Crestron
“Wi-Fi friendly” RF technology permits selection from 16 ISM
within the 2.4 GHz spectrum to minimize the possibility of interference
with other RF equipment including 802.11 devices. The CEN-RFGW-EX
affords a range of approximately 100 feet (30 meters) indoors.
Up to 16 MLX-2 remotes or other infiNET EX devices, may be
associated with a single CEN-RFGW-EX. Setup is simple, utilizing
dynamic discovery to locate and acquire each remote automatically. Each
wireless connection is monitored continuously, diligently keeping track
when remotes go to sleep or wander out of range and restoring
communications seamlessly when any remote reappears on the network.
More than just a wireless bridge, the CEN-RFGW-EX actually functions
as a proxy for each MLX-2, processing every button press and display
change right onboard. So when a remote goes to sleep or out of range, the
gateway continues communicating with the control system, keeping sync
with every command and updating the remote’s display the instant it
awakens or reconnects.
* Industrial, Scientific and Medical; refers to frequency range used for unlicensed
communications applications, such as Wi-Fi.
®
infiNET EX devices as part of a Crestron control system.
or PoE (Power-over-Ethernet) powers the
CEN-RFGW-EX right through the network wiring, eliminating the need
for a separate wall-wart power supply. The CEN-RFGW-EX is available
with a PoE Injector, PWE-4803RU included (as model
CEN-RFGW-EX-PWE), which simply connects inline with the Ethernet
cable connected to the gateway, allowing for installation at any
convenient location. Or, using Crestron’s 5-port PoE switch
(CEN-SW-POE-5, sold separately), up to four gateways and other PoE
devices can be powered from a single location, simplifying design and
wiring.
Features and Functions
• infiNET EX 2-way RF wireless transceiver/gateway
• Manages up to 16 MLX-2 handheld remotes or other Crestron
(without antenna)
Height 6.41 in (16.27 cm)
Width 3.91 in (9.94 cm)
Depth 1.43 in (3.62 cm)
Weight 13.1 oz (372.7 g)
Available Models
CEN-RFGW-EX infiNET EX Gateway
CEN-RFGW-EX-PWE infiNET EX Gateway
w/PoE Injector
Available Accessories PWE-4803RU PoE Injector (included with model
CEN-RFGW-EX-PWE)
CEN-SW-POE-5 5-Port PoE Switch
1. May be powered by PoE or Cresnet network power.
2. The latest software versions can be obtained from the Crestron website. Refer to
the NOTE following these footnotes.
3. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest
Crestron Product Catalog for a complete list of 2-Series control systems.
NOTE: Crestron software and any files on the website are for authorized
Crestron dealers and Crestron Authorized Independent Programmers
(CAIP) only. New users may be required to register to obtain access to
certain areas of the site (including the FTP site).
operating power supplied from
Cresnet network or PoE
3 NET LED (1) Yellow LED, indicates
communication with the
Cresnet system
4 ACTIVITY LED (1) Red LED, indicates
wireless communications
5 ACQUIRE
(Button and LED)
(1) Recessed pushbutton with
red LED, used to set up
connections with wireless
devices
6 SETUP
(Button and LED)
7 LAN PoE
GREEN
LED
PIN 8
2, 3, 4
YELLOW
LED
PIN 1
(1) Recessed pushbutton with
red LED, used to set up
connection with the control
system via Cresnet or Ethernet
(1) 8-wire RJ-45 with two LED
indicators;
10BASE-T/100BASE-TX
Ethernet port, 802.3af Power
over Ethernet compliant;
Green LED indicates link
status;
Yellow LED indicates Ethernet
activity
1. Interface connector for NET port is provided with the unit.
2. To determine which is pin 1 on the cable, hold the cable so that the end of the
eight pin modular jack is facing away from you, with the clip down and copper
side up. Pin 1 is on the far left.
3. Power should be supplied through either the LAN PoE port or the NET port but
not both.
4. The pin out table indicates signal connections. DC power applied by Ethernet
power sourcing equipment (PSE) can connect to either signal pins or N/C pins.
(1) 3.5 mm detachable terminal
block;
Cresnet slave port, connects to
Cresnet control network
24: Power (24 Volts DC)
Y: Data
Z: Data
G: Ground