Crestron TPMC-V12-WALL Installation Manual

Crestron TPMC-V12-WALL,

V12-WALL & WMKC-V12

Wall Mount & Chassis Wall Mount
Kits for TPMC-V12 & V12
Installation Guide

This document was prepared and written by the Technical Documentation department at:

Crestron Electronics, Inc.

15 Volvo Drive

Rockleigh, NJ 07647

1-888-CRESTRON

Regulatory Compliance

As of the date of manufacture, the TPMC-V12-WALL, V12-WALL and WMKC-V12 have been tested and
found to comply with specifications for CE marking and standards per EMC and Radiocommunications
Compliance Labelling.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

Consult the dealer or an experienced radio/TV technician for help

Industry Canada (IC) Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

All brand names, product names and trademarks are the property of their respective owners.

©2011 Crestron Electronics, Inc.

Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12 Wall Mount Kits

Contents

Wall Mount & Chassis Wall Mount Kits for TPMC-V12 & V12:
TPMC-V12-WALL, V12-WALL & WMKC-V12 1

Description.................................................................................................................................1

Setup .......................................................................................................................................... 7

Supplied Hardware......................................................................................................7

Installation...................................................................................................................8

Resources................................................................................................................................. 13

Reference Documents................................................................................................13

Further Inquiries........................................................................................................13

Future Updates ..........................................................................................................13

Return and Warranty Policies..................................................................................................14

Merchandise Returns / Repair Service ......................................................................14

CRESTRON Limited Warranty.................................................................................14

Installation Guide – DOC. 6893B Contents • i

Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12 Wall Mount Kits

Wall Mount & Chassis Wall Mount
Kits for TPMC-V12 & V12:
TPMC-V12-WALL, V12-WALL &
WMKC-V12

Description

Wall Mount and Chassis Wall Mount Kits (TPMC-V12-WALL, V12-WALL and
WMKC-V12) for TPMC-V12 and V12 allow wall or flat-surface mounting for the
Crestron® TPMC-V12 Integrated 12” Touchpanel and V12 V-Panel™ 12”
Touchpanel Display. These kits provide the necessary parts to secure a touchpanel in
a mounting surface using one of several mounting options. Refer to the table below
for a complete list of mounting options.

Mounting Options for TPMC-V12-WALL, V12-WALL and WMKC-V12

PRE-

CONSTRUCTION

OPTION

Back Box Kit - BB-V12 6811

Pre-Construction

Mount Kit

Mud Mount Kit

(Accessory)

- Mud Mount Kit WMKM-V12 6892

- Trim Ring Mount Kit WMKT-V12 6813

The Installation Guides for the TPMC-V12 and V12 mounting options are available
from the Crestron Web site (www.crestron.com/manuals

The TPMC-V12-WALL is a pre-assembled TPMC-V12 with chassis wall mount kit
(WMKC-V12). This model consists of a TPMC-V12 Integrated 12” Touchpanel
mounted inside of a chassis and is ready for mounting in a wall or similar flat
surface. Included are six screws to mount the touchpanel and a magnetic bezel. It is
available in black or white.

POST-

CONSTRUCTION

OPTION

- PMK-V12 6812

- MMK-V12 6892

MODEL

NUMBER

).

DOCUMENT

NUMBER

Installation Guide – DOC. 6893B Wall Mount Kits: TPMC-V12-WALL, V12-WALL & WMKC-V12 • 1

Wall Mount Kits Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12

The V12-WALL is a pre-assembled V12 V-Panel with chassis wall mount kit
(WMKC-V12). This model consists of a V12 V-Panel 12” Touchpanel Display
mounted inside of a chassis and is ready for mounting in a wall or similar flat
surface. Included are six screws to mount the touchpanel and a magnetic bezel. It is
available in black or white.

The WMKC-V12 provides a solution for converting a TPMC-V12 Integrated 12”
Touchpanel or V12 V-Panel 12” Touchpanel Display for mounting in a wall or
similar flat surface. Using the WMKC-V12, a TPMC-V12, TPMC-V12-TILT, V12
or V12-TILT model can be effectively converted to the equivalent of a
TPMC-V12-WALL or V12-WALL. The kit consists of a VESA mount, metal
chassis and a magnetic bezel. It is available in black or white.

2 • Wall Mount Kits:TPMC-V12-WALL, V12-WALL & WMKC-V12 Installation Guide – DOC. 6893B

Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12 Wall Mount Kits

The dimensions of the TPMC-V12-WALL, V12-WALL and WMKC-V12 are shown
below.

TPMC-V12-WALL and V-12-WALL Overall Dimensions (Front, Side and Rear Views – Without Bezel)

1.80 in

(46 mm)

12.67 in

(322 mm)

11.16 in

(284 mm)

1.69 in

(43 mm)

12.11 in

(308 mm)

10.51 in

(267 mm)

Installation Guide – DOC. 6893B Wall Mount Kits: TPMC-V12-WALL, V12-WALL & WMKC-V12 • 3

Wall Mount Kits Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12

TPMC-V12-WALL and V12-WALL Overall Dimensions (Front and Side Views - With Bezel)

13.04 in

(332 mm)

11.54 in

(293 mm)

2.01 in

(52 mm)

4 • Wall Mount Kits:TPMC-V12-WALL, V12-WALL & WMKC-V12 Installation Guide – DOC. 6893B

Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12 Wall Mount Kits

WMKC-V12 Overall Dimensions (Front, Side and Bottom Views)

1.73 in

(44 mm)

12.67 in

(322 mm)

0.05 in
(2 mm)

11.16 in

(284 mm)

12.11 in

(308 mm)

VESA Mounting Bracket Overall Dimensions (Front and Side Views)

4.50 in

(115 mm)

0.32 in

(8 mm)

10.51 in

(267 mm)

4.50 in

(115 mm)

Installation Guide – DOC. 6893B Wall Mount Kits: TPMC-V12-WALL, V12-WALL & WMKC-V12 • 5

Wall Mount Kits Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12

Bezel Overall Dimensions (Front and Side Views)

13.04 in

(332 mm)

11.54 in

(294 mm)

0.33 in

(9 mm)

6 • Wall Mount Kits:TPMC-V12-WALL, V12-WALL & WMKC-V12 Installation Guide – DOC. 6893B

Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12 Wall Mount Kits

Setup

Supplied Hardware

The TPMC-V12-WALL consists of a TPMC-V12 Integrated 12” Touchpanel
mounted inside of a chassis. It includes mounting screws. These parts attach to a V12
mounting option.

The V12-WALL consists of a V12 V-Panel 12” Touchpanel Display mounted inside
of a chassis. It includes mounting screws. These parts attach to a V12 mounting
option.

The WMKC-V12 consists of six parts: a mounting plate, chassis, bezel and three sets
of mounting screws. The final assembled product is the TPMC-V12-WALL or
V12-WALL.

The hardware supplied with the TPMC-V12-WALL and V12-WALL is listed in the
following table.

Supplied Hardware for the TPMC-V12-WALL and V12-WALL

DESCRIPTION PART

QUANTITY

NUMBER

Bezel, Plastic, V12, White
(TPMC-V12-WALL-W and
V12-WALL-W only)

Bezel, Plastic, V12, Black
(TPMC-V12-WALL-B and
V12-WALL-B only)

Screw, #06-32 x 1 1/2” 2007254 6

4509644 1

4509645 1

The hardware supplied with the WMKC-V12 is listed in the following table.

Supplied Hardware for the WMKC-V12

DESCRIPTION PART

QUANTITY

NUMBER

Bezel, Plastic, White
(WMKC-V12-W only)

Bezel, Plastic, Black
(WMKC-V12-B only)

Chassis, Wall Mount

Bracket, VESA Mount

Screw, #08-32 x 1/4”

Screw, #06-32 x 1 1/2”

Screw, M4 x 12 mm

4509644

4509645

2024533

2023927

2007263

2007254

2023678

1

1

1

1

4

6

4

For simplicity within this guide, the color designation is omitted and
TPMC-V12-WALL, V12-WALL and WMKC-V12 are used except where noted.

Installation Guide – DOC. 6893B Wall Mount Kits: TPMC-V12-WALL, V12-WALL & WMKC-V12 • 7

Wall Mount Kits Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12

Installation

This section provides assembly and installation procedures for the Wall Mount and
Chassis Wall Mount Kits. The “WMKC-V12 Procedure” starts below and the
“TPMC-V12-WALL and V12-WALL Procedure” starts on page 10. Be sure to
review each procedure before starting.

WMKC-V12 Procedure

This section provides the necessary steps for the assembly of a TPMC-V12
Integrated 12” Touchpanel or V12 V-Panel 12” Touchpanel Display into a wall
mount chassis. Review the procedure and complete the steps in the order provided.
The only tool required is a #2 Phillips screwdriver.

NOTE: If converting a TPMC-V12-TILT or V12-TILT, remove the plastic cover on
the back of the panel to expose the tilt arm mounting assembly. Then remove the
four screws that hold the tilt arm with a #2 Phillips screwdriver. Follow the
procedure below to mount the TPMC-V12 or V12 into the chassis wall mount kit.

1. Attach the symmetrical VESA mounting bracket (2023927) to the rear of
the touchpanel using the four included M4 x 12 mm screws (2023678).
Make sure that the stand offs are facing away from the rear of the
touchpanel. Do not over tighten screws.

2. Place the wall mount chassis (2024533) over the back of the touchpanel.
The large cutout in the chassis should align with the bottom of the
touchpanel. Align the screw holes and secure the touchpanel with the four
included #08-32 x 1/4” Phillips head screws (2007263). The finished
product is essentially the TPMC-V12-WALL or V12-WALL. Refer to the
illustration on the following page for visual guidance.

8 • Wall Mount Kits:TPMC-V12-WALL, V12-WALL & WMKC-V12 Installation Guide – DOC. 6893B

Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12 Wall Mount Kits

WMKC-V12 Assembly (Exploded View)

Screws (4) #08-32 x 1/4"

Wall Mount Chassis
(2024533)

Screws (4) M4 x 12 mm
(2023678)

(2007263 )

TPMC-V12
or V12 Panel

VESA Mounting Bracket
(2023927)

3. Follow the TPMC-V12-WALL and V12-WALL procedure on the following
page to install the assembly into a V12 mounting option.

Installation Guide – DOC. 6893B Wall Mount Kits: TPMC-V12-WALL, V12-WALL & WMKC-V12 • 9

Wall Mount Kits Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12

TPMC-V12-WALL and V12-WALL Procedure

This section provides the necessary steps for the installation of the
TPMC-V12-WALL or V12-WALL into a V12 mounting option. It is assumed that
wiring has been run and an appropriate V12 mounting option has been installed
according the instructions in the latest version of its Installation Guide.

Complete the steps in the order provided. The only tool required and not supplied is
a #2 Phillips screwdriver.

CAUTION: Allow an air gap of at least 12 inches (305 mm) in the wall cavity
above and below the touchpanel for heat dissipation.

NOTE: The illustration in this procedure shows the installation of the

TPMC-V12-WALL or V12-WALL with the BB-V12. Even though the illustration
only shows the BB-V12, the procedure is identical for other V12 mounting options.

1. If a cover plate is attached, use a #2 Phillips screwdriver to loosen and
remove the six screws and plate.

2. Connect all required cables to the touchpanel. Refer to “Hardware Hookup”
section of the TPMC-V12 & TPMC-V15 Operations Guide (Doc. 6940) or
the V12 & V15 Operations Guide (Doc. 6806). Both are available from the
Crestron Web site.

3. Insert the touchpanel (without its bezel) into the mounting option and align
the six screw holes. Do not handle touchpanel by the screen.

4. Insert and tighten the six included #06-32 x 1 1/2” screws (2007254) (finger
tight and then using a #2 Phillips screwdriver, tighten an additional
1/8-turn). Refer to the illustration on the following page.

10 • Wall Mount Kits:TPMC-V12-WALL, V12-WALL & WMKC-V12 Installation Guide – DOC. 6893B

Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12 Wall Mount Kits

Secure TPMC-V12-WALL or V12-WALL to the Mounting Option

BB-V12 (not included)
Back Box is shown installed

Drywall Cutout

TPMC-V12-WALL
or V12-WALL

Screws (6) #06-32 x 1 1/2"
(2007254)

5. Observing the orientation of the word BOTTOM on the back of the
magnetic bezel, place the bezel over the touchpanel. Refer to the illustration
on the following page.

Installation Guide – DOC. 6893B Wall Mount Kits: TPMC-V12-WALL, V12-WALL & WMKC-V12 • 11

Wall Mount Kits Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12

Mount Bezel to TPMC-V12 or V12 Touchpanel

Bezel
(4509645 or 4509644)

12 • Wall Mount Kits:TPMC-V12-WALL, V12-WALL & WMKC-V12 Installation Guide – DOC. 6893B

Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12 Wall Mount Kits

Resources

Reference Documents

The latest version of all documents mentioned within the guide can be obtained from
the Crestron Web site (www.crestron.com/manuals). This link will provide a list of
product manuals arranged in alphabetical order by model number.

List of Related Reference Documents

DOCUMENT TITLE

BB-V12 Pre-Construction Wall Mount Back Box

MMK-V12 and WMKM-V12 Mud Mount Kits

PMK-V12 Pre-Construction Mounting Kit

TPMC-V12 & TPMC-V15 Integrated 12” & 15” Touchpanels

V12 & V15 V-Panel 12” & 15” Touchpanel Displays

WMKT-V12 Trim Ring Mount Kit

Further Inquiries

If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling Crestron at 1-888-CRESTRON [1-888-273-7876].

You can also log onto the online help section of the Crestron Web site
(www.crestron.com/onlinehelp
users will need to establish a user account to fully benefit from all available features.

) to ask questions about Crestron products. First-time

Future Updates

As Crestron improves functions, adds new features and extends the capabilities of
the TPMC-V12-WALL, V12-WALL and WMKC-V12, additional information may
be made available as manual updates. These updates are solely electronic and serve
as intermediary supplements prior to the release of a complete technical
documentation revision.

Check the Crestron Web site periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.

Installation Guide – DOC. 6893B Wall Mount Kits: TPMC-V12-WALL, V12-WALL & WMKC-V12 • 13

Wall Mount Kits Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12

Return and Warranty Policies

Merchandise Returns / Repair Service

1. No merchandise may be returned for credit, exchange or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying
the nature of the problem, name and phone number of contact person, RMA number and
return address.

2. Products may be returned for credit, exchange or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with
RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect
or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its
sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any
products returned with an RMA.

3. Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.

CRESTRON Limited Warranty

CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials
and workmanship under normal use for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical
parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and
overlay components are covered for 90 days; batteries and incandescent lamps are not covered.

This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if
any.

CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.

This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a
third party or made by the purchaser for a third party.

CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.

Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are
limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.

14 • Wall Mount Kits:TPMC-V12-WALL, V12-WALL & WMKC-V12 Installation Guide – DOC. 6893B

Crestron TPMC-V12-WALL, V12-WALL & WMKC-V12 Wall Mount Kits

This page is intentionally left blank.

Installation Guide – DOC. 6893B Wall Mount Kits: TPMC-V12-WALL, V12-WALL & WMKC-V12 • 15

Crestron Electronics, Inc. Installation Guide – DOC. 6893B

15 Volvo Drive Rockleigh, NJ 07647 (2025426)
Tel: 888.CRESTRON 02.11
Fax: [phone] Specifications subject to
www.crestron.com change without notice.