Crestron PMK-8X-DSW Pre-Construction Wall Mount Kit
Pre-Construction Wall Mount Kit:
PMK-8X-DSW
Description
The PMK-8X-DSW mounting kit provides a nail-in solution for installing the
TPMC-8X-DSW Wall Mount Docking Station. Designed for pre-construction
applications, the PMK-8X-DSW permits fastening to the studs of a framed wall prior
to installation of sheet rock. A blank cover plate is included.
The PMK-8X-DSW includes a 12-inch long, 18 AWG jumper wire to secure
touchpanel cabling prior to drywall installation and to avoid damaging the cables
when the opening is routed. Refer to the physical views of the PMK-8X-DSW shown
on the following page. The table that follows lists all parts included with the
PMK-8X-DSW.
Crestron PMK-8X-DSW Pre-Construction Wall Mount Kit
Installation
The PMK-8X-DSW consists of a single metal plate, which fastens to the stud of a
framed wall prior to hanging drywall. Standard drywall nails or screws to attach the
PMK-8X-DSW are not supplied (length can vary).
The plate is designed to provide the necessary support for a single TPMC-8X-DSW
and touchpanel. It can mount to the right or left side of a stud. Confirm that the
PMK-8X-DSW is level before applying drywall. An opening with the dimensions
shown below must be made in the drywall. Refer to the following illustration for
exact cutout dimensions. Position the opening to expose the #06-32 tapped hole in
each corner.
Dimensions for Drywall Cutout
11.19 in
(28.34 cm)
3/16 in
(4.76 cm)
(DRILL SIZE #Q)
TYP (4X)
0.10 in
(0.25 cm)
7.38 in
(18.74 cm)
1.19 in
(3.02 cm)
1.12 in
(2.84 cm)
10.99 in
(27.91 cm)
9.38 in
(23.81 cm)
9.70 in
(24.63 cm)
0.17 in
(0.41 cm)
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the touchpanel for heat dissipation.
NOTE: The TPMC-8X-DSW may be attached to the PMK-8X-DSW using the four
included #06-32 x 1 ½” screws (two at each side). Refer to the illustration above for
drill bit size and screw hole locations.
Complete the installation by either installing the TPMC-8X-DSW and touchpanel,
leaving the hole open (if permitted by local building codes) or installing the supplied
cover plate with the included #06-32 x 1½” screws, as shown in the illustration on
the following page.
Pre-Construction Wall Mount Kit Crestron PMK-8X-DSW
Attaching Cover
STUD
PRE-CONSTRUCTION PLATE
(2017635) MUST BE LEVEL BEFORE
APPLICATION OF DRYWALL
DRYWALL
SCREWS (4) #06-32 x 1-½"
PAN HEAD (2007254)
METAL COVER PLATE (2017660)
TO COVER CUTOUT IN DRYWALL
BEFORE TPMC-8X-DSW IS INSTALLED
(MAY BE REQUIRED BY LOCAL BUILDING CODES)
If the TPMC-8X-DSW and touchpanel are to be installed, refer to the latest revision
of the TPMC-8X-DSW Installation Guide (Doc. 6588) for installation instructions.
The document is available from the Crestron website
(http://www.crestron/com/manuals
). Refer also to the comprehensive illustration on
Crestron PMK-8X-DSW Pre-Construction Wall Mount Kit
Touchpanel Mounting Using PMK-8X-DSW – Exploded View
PMK-8X-DSW
DRYWALL
TPMC-8X-DSW
(bezel removed)
TPMC-8X-DSW
MOUNTING SCREWS
(4) #06-32 x 1-1/2"
(2 ON EACH SIDE)
(bezel)
If too much of the mounting plate is exposed after the drywall is cut, you may need
to patch the area. Crestron provides the following accessories:
• TMK-8X-DSW (Doc. 6582) – for smaller repairs and to provide a smooth
edge at the opening. This option provides a finished appearance and is
preferred when wallpaper is hung.
• MMK-8X-DSW (Doc. 6581) – for larger repairs and to fill in larger
irregularities around the opening (requires plastering)
The manuals for the TMK-8X-DSW and MMK-8X-DSW are available from the
Crestron website.
Pre-Construction Wall Mount Kit Crestron PMK-8X-DSW
Contact Information and Updates
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876].
For assistance in your local time zone, refer to the Crestron website
(http://www.crestron.com/offices
You can also log onto the online help section of the Crestron website
(http://www.crestron.com/onlinehelp
First-time users will need to establish a user account to fully benefit from all
available features.
As of the date of manufacture, the PMK-8X-DSW has been tested and found to
comply with specifications for CE marking.
) for a listing of Crestron worldwide offices.
) to ask questions about Crestron products.
Future Updates
As Crestron adds improvements to the PMK-8X-DSW, additional information may
be made available as manual updates. These updates are solely electronic and serve
as intermediary supplements prior to the release of a complete technical
documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
Crestron PMK-8X-DSW Pre-Construction Wall Mount Kit
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying
the nature of the problem, name and phone number of contact person, RMA number and
return address.
2. Products may be returned for credit, exchange or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with
RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect
or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its
sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any
products returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials
and workmanship under normal use for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical
parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and
overlay components are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if
any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a
third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are
limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.
Trademark Information
All brand names, product names and trademarks are the sole property of their respective owners. Windows is a registered trademark
of Microsoft Corporation. Windows95/98/Me/XP/Vista and WindowsNT/2000 are trademarks of Microsoft Corporation.