Crestron PMK-4L User Manual

Pre-Construction Mount Kit: PMK-4L

Description

The PMK-4L is a pre-construction mount kit for the
Crestron Isys® TPS-4L and TPMC-4L wall mounted
touchpanels. The PMK-4L is used for installation on a
stud. For custom touchpanel placement without a stud,
use the TMK/WMKT-4L, MMK/WMKM-4L or the
WMKB-4L. The PMK-4L includes a 12-inch long, 18
AWG jumper wire to secure touchpanel cabling prior to
drywall installation and to avoid damaging the cables
when the opening is routed. Refer to the physical views
(bottom, side, and front) of the PMK-4L, shown after this
paragraph. The table that follows lists all parts included
with the PMK-4L.

NOTE: This mounting kit is to be used only with the
TPS-4L and TPMC-4L wall-mounted series of
touchpanels.

PMK-4L Physical Views

FOR

FOR DRYWALL NAILS (NOT INCLUDED)

FOR DRYWALL SCREWS (NOT INCLUDED)

SECURE 18 AWG
JUMPER WIRE IN
NOTCH TO HANG
CABLES AWAY FROM
CUTTING TOOLS

14.01 cm

5.55 in

DRYWALL
NAILS
(NOT
INCLUDED)

nails or screws to attach the PMK-4L are not supplied
(length can vary).

Metal Plate Secured to Stud

The plate is designed to provide the necessary support for
a single touchpanel and can mount to the right or left side
of a stud. Confirm that the PMK-4L is level before
applying drywall. A rectangular opening with the
dimensions shown in the illustration after this paragraph
must be made in the drywall. Verify that the opening
exposes the #04-40 tapped holes in each corner.

Dimensions for Drywall Cutout

5.60 in

14.22 cm

8.37 in

21.56 cm

6.00 in

15.24 cm

4.50 in

11.43 cm

Supplied Components

DESCRIPTION PART NUMBER QUANTITY

Metal, Plate, Pre-Construction 2013238 1

Cover Plate 2013239 1

Screw, #04-40, 1-1/2”L, Pan, Phil 2007190 4

Jumper wire, 12”L, 18AWG, Black 2007838 1

0.30 in

0.76 cm

3.66 in

9.30 cm

1.30 in

3.30 cm

4.16 in

10.57 cm

If the opening is too large, two pre-construction
accessories are available to make adjustments. Use the
optional TMK-4L (Trim Ring Kit) to provide a smooth
edge at the opening. This option provides a finished
appearance and is preferred with wallpaper. Use the
optional MMK-4L (Mud Ring Kit) to fill in larger
irregularities around the opening (requires plastering).

Complete the installation by either installing the

Installation

The PMK-4L consists of a single metal plate, which
fastens to the stud of a framed wall prior to hanging
drywall (shown after this paragraph). Standard drywall

Crestron Electronics, Inc. Installation Guide – DOC. 6388

15 Volvo Drive Rockleigh, NJ 07647 (2013260)
Tel: 888.CRESTRON 12.05
Fax: [phone] Specifications subject to
www.crestron.com change without notice.

touchpanel, leaving the hole open (if permitted by local
building codes), or installing the supplied cover plate with
the included #04-40 x 1½” screws (shown after this
paragraph). If the touchpanel is to be installed, refer to the

Pre-Construction Mount Kit Crestron PMK-4L

latest revision of the TPS-4L Operations Guide (Doc.

6449) or TPMC-4L Operations Guide (Doc. 6450) for
installation instructions.

Attaching Cover

STUD

PRE-CONSTRUCTION METAL
PLATE (2013238) MUST BE
LEVEL BEFORE
APPLICATION OF DRYW ALL

DRYWALL

#04-40 x 1 ½ PAN
HEAD SCREW
(2007190) QTY. 4

COVER PLATE
(2013239) TO
COVER CUTOUT IN
DRYWALL BEFORE
TOUCHPANEL IS
INSTALLED (SEE
LOCAL BUILDING
CODES)

CAUTION: Allow an air gap of at least 12 inches in
the wall cavity above the touchpanel for heat
dissipation.

NOTE: Prior to mounting the touchpanel, ensure that
the PMK-4L is flush with the drywall (no kinks or
bends in the metal). Any separation may make
screwing in the touchpanel more difficult. One can
purchase and attach a TMK-4L or an MMK-4L to
keep the PMK-4L straight.

Further Inquiries

If you cannot locate specific information or have
questions after reviewing this guide, please take
advantage of Crestron's award winning customer service
team by calling the Crestron corporate headquarters at
1-888-CRESTRON [1-888-273-7876]. For assistance in
your local time zone, refer to the Crestron website
(www.crestron.com
offices.

You can also log onto the online help section of the
Crestron website to ask questions about Crestron
products. First-time users will need to establish a user
account to fully benefit from all available features.

As of the date of manufacture, the PMK-4L has been
tested and found to comply with specifications for CE
marking.

) for a listing of Crestron worldwide

Return and Warranty Policies

Merchandise Returns / Repair Service

1. No merchandise may be returned for credit, exchange, or
service without prior authorization from CRESTRON. To
obtain warranty service for CRESTRON products, contact
the factory and request an RMA (Return Merchandise
Authorization) number. Enclose a note specifying the nature
of the problem, name and phone number of contact person,
RMA number, and return address.

2. Products may be returned for credit, exchange, or service
with a CRESTRON Return Merchandise Authorization
(RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J., or
its authorized subsidiaries, with RMA number clearly marked
on the outside of all cartons. Shipments arriving freight
collect or without an RMA number shall be subject to refusal.
CRESTRON reserves the right in its sole and absolute
discretion to charge a 15% restocking fee, plus shipping
costs, on any products returned with an RMA.

3. Return freight charges following repair of items under
warranty shall be paid by CRESTRON, shipping by standard
ground carrier. In the event repairs are found to be non­warranty, return freight costs shall be paid by the purchaser.

CRESTRON Limited Warranty

CRESTRON ELECTRONICS, Inc. warrants its products to be free from
manufacturing defects in materials and workmanship under normal use
for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other
moving or rotating mechanical parts, pan/tilt heads and power supplies
are covered for a period of one (1) year; touchscreen display and overlay
components are covered for 90 days; batteries and incandescent lamps
are not covered.

This warranty extends to products purchased directly from CRESTRON
or an authorized CRESTRON dealer. Purchasers should inquire of the
dealer regarding the nature and extent of the dealer's warranty, if any.

CRESTRON shall not be liable to honor the terms of this warranty if the
product has been used in any application other than that for which it was
intended, or if it has been subjected to misuse, accidental damage,
modification, or improper installation procedures. Furthermore, this
warranty does not cover any product that has had the serial number
altered, defaced, or removed.

This warranty shall be the sole and exclusive remedy to the original
purchaser. In no event shall CRESTRON be liable for incidental or
consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is
not liable for any claim made by a third party or made by the purchaser
for a third party.

CRESTRON shall, at its option, repair or replace any product found
defective, without charge for parts or labor. Repaired or replaced
equipment and parts supplied under this warranty shall be covered only
by the unexpired portion of the warranty.

Except as expressly set forth in this warranty, CRESTRON makes no
other warranties, expressed or implied, nor authorizes any other party to
offer any warranty, including any implied warranties of merchantability
or fitness for a particular purpose. Any implied warranties that may be
imposed by law are limited to the terms of this limited warranty. This
warranty statement supercedes all previous warranties.

Trademark Information

All brand names, product names, and trademarks are the sole property of their respective
owners. Windows is a registered trademark of Microsoft Corporation. Windows95/98/Me/XP
and WindowsNT/2000 are trademarks of Microsoft Corporation.

2 • Pre-Construction Mount Kit: PMK-4L Installation Guide – DOC. 6388