Crestron LEPB-2, LEPB-3 User Manual

Power Extender

TOP

Dimming Control

Fluorescent Only

Cat. No. PE200-1

Rating: 1920VA

For use with Advance Mark X™

or Hi-lume® dimming ballasts.

For more information go to

INSTALLATION INSTRUCTIONS

LIMITED 2 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for two years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such two year period the product is returned prepaid, with proof of purchase date, and a description of the problem to

Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591 (In Canada send to Leviton Mfg. of Canada Ltd., 165 Hymus Blvd., Point Claire, (Quebec), Canada H9R 1E9). This warranty excludes and there is

disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

For Technical Assistance Call:

1-800-824-3005 (U.S.A. Only)

1 800 405-5320 (Canada Only)

www.leviton.com

120VAC, 50/60Hz

Cat. No. PE200-7

Rating: 3000VA

277VAC, 50/60Hz

www.leviton.com

DI-000-PE200-00A-Pilot

FEATURES

•Works with Mark X™ or Hi-lume® 120V (Cat.No. PE200-1) and 277V (Cat. No. PE200-7) dimmable ballasts. NOTE: Hi-lume

•Low-end adjustment available for setting the minimum brightness level.

•Works with any Dimensions 3200 Series Multizone Controller/Dimmer to extend load capacity on any zone.

is a registered trademark of the Lutron Electronics Co., Inc.

DESCRIPTION

The Leviton Power Extender, Cat. No. PE200-1 and PE200-7, will emulate the characteristics of the dimmer that it is connected to in terms of dimming range and resolution.

Compatibility

• Box Mounted Dimmers – Must use a 120V, 600VA Mark X™ version of the following families: Monet,

Illumatech, Sureslide, Mural, and Touch Point.

• D3200 – Zone must be configured to work with fluorescent loads. Refer to D3200 User guide for details.

• Architectual Systems – Works with all families.

NOTE: For dimmers that include a Neutral wire, the dimmer Neutral wire must be connected.

NOTE: The PE200 has a minimum level adjustment.

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

INSTALLATION INSTRUCTIONS

WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES

AND REGULATIONS.

WARNING: IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED

ELECTRICIAN.

OTHER CAUTIONS:

1. BOTH LIGHTING FIXTURE AND CONTROLLER MUST BE GROUNDED.

2. DISCONNECT POWER WHEN SERVICING FIXTURE OR CHANGING LAMPS.

3. TO BE USED FOR DIMMING ONLY WITH ADVANCE MARK X™ DIMMING BALLASTS.

4. USE THIS DEVICE ONLY WITH COPPER OR COPPER CLAD WIRE. WITH ALUMINUM WIRE USE ONLY

DEVICES MARKED CO/ALR OR CU/AL.

NOTE: The Power Extender must be installed in a 1900 Box with Raised Cover or a properly grounded metal 2gang wall box, 3.5" (8.9 cm) deep (refer to Figure 1A and 1B). Depending on the application and the number of connections, more space may be needed. If so, use an appropriate size box or box extension.

TO INSTALL:

1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKERS OR FUSES

AND TEST THAT POWER IS OFF BEFORE WIRING!

MORE THAN ONE CIRCUIT BREAKER CAN POWER THIS DEVICE. DISCONNECT “ALL” POWER SOURCES BEFORE SERVICING CONTROL.

2. Remove 1/2" (1.3 cm) of insulation from each circuit conductor in wall box. Make sure that ends of conductors are straight.

3. Connect lead wires per appropriate WIRING DIAGRAM and FIGURE 2 as follows: All connections to the output terminals should be made using #12 AWG wire. Each power terminal can accept up to two(2) #12 wires. The recommended installation torque is 9.0 in.-lbs. for line voltage connections.

4. Carefully position all wires to provide room in wall box for Power Extender. All Power Extenders must have 4-1/2" spacing above and below each unit for proper ventilation and heat dissipation (refer to Figure 4).

Line voltage

wiring should be at least 6 ft. away from sound or electronic equipment wiring. Mount Power Extender

to outlet box with “TOP” facing up (refer to Figure 3).

For Wall Box Mounting: Refer to Figure 1A.

For Flush Mounting: Refer to Figure 1B.

Figure 1A: Surface Mounting

1900 Box

2 Gang Raised Cover

Raised Cover Mounting Screws (4 Places)

P O T

Power

Extender

Power Extender

Wallplate

Figure 2: End View

NEUTRAL

CONTROL

For Panel Mounting (not shown), Proceed as follows:

a. The enclosure must be in accordance with all local and national

electrical codes.

SWITCH

HOT

LOAD

HOT

Figure 3: Front View

Figure 1B: Flush Mounting

1900 Box

Power

Extender

Power Extender

Figure 4: Front View Spacing

TOP

Green LED

Trim

Adjustment

4-1/2" (11.4 cm) Minimum

TOP

4-1/2" (11.4 cm) Minimum

2 Gang Raised Cover

Raised Cover Mounting Screws (4 Places)

OP T

Wallplate

b. Leviton DOES NOT recommend using a door to enclose the front of

a panel, since this restricts airflow to the controls.

c. If mounting multiple controls in an enclosure:

• Ambient temperature within an enclosure “MUST REMAIN

BETWEEN” 32˚-104˚F (0˚-40˚C).

• If not mounting in a metal enclosure, all units “MUST” be mounted in a wall box.

d. To improve heat dissipation of controls, remove the faceplate from the unit.

5. Restore power at circuit breaker or fuse.

6. Tu rn ON the dimmer.

7. Using the dimmer control, verify that the load DIMS and BRIGHTENS smoothly and the lamps do not flicker.

8. Attach wallplate by aligning tabs on back of plate with grooves in fins on Power Extender (refer to Figure 1A and Figure 1B). INSTALLATION IS COMPLETE.

OPERATION

The operation of the PE200 follows the operation of the dimmer it is connected to. To operate the PE200, the dimmer must be operated as follows:

ON: Tu rn ON the dimmer. Turn OFF: Tu rn OFF the dimmer. DIM: Adjust the dimmer DIM level. BRIGHTEN: Adjust the dimmer BRIGHTNESS level. Green LED: Illuminates when load in ON. Air Gap: Activating the air gap on the dimmer will cause the PE200 to turn its controlled Load OFF.

CAUTION: The Power Extender will still remain powered, but it will not activate the load.

The PE200 has an air gap relay built in, therefore, the ballasts will be disconnected by an air gap when the dimmer is OFF or the air gap control on the dimmer is activated.

TROUBLESHOOTING

Used if Dimmer/Switch has Neutral connection (

Power

Extender

D3206/08

Controller/Dimmer

Hot (Black)

(Load)

Neutral 2 (White)

Neutral 1 (White)

Line 1 (120VAC)

Line 2 (120VAC)

Green

Ground

LOAD

MARK X™ DIMMABLE

BALLAST

Black

White

Neutral

Load

Line

120V Mark X™

Type Dimmer

Green

Ground

)

Neutral

Load

Line

NEUTRAL

LOAD

HOT

SWITCH

HOT

CONTROL

INPUT

OUTPUT

• The Power Extender is not powered

- Circuit breaker is OFF.

- Power wires are not connected properly.

• The load does not turn ON, but the Power Extender is powered

- The dimmer is OFF.

- The dimmer air gap switch is activated.

- The dimmer is connected to a separate circuit, and the circuit breaker is OFF.

- Dimmer is mis-wired

• Control Neutral (from dimmer) wire is not connected to the Neutral of the Line pair feeding the dimmer.

• No full range dimming

- Remove wallplate if necessary and ensure the Power Extender trim adjusment (refer to Figure 3) is set to its fully counter-clockwise (ccw) minimum level.

Cat. No. PE200-1, 120V – For use with

Advance Mark X™ 120V Dimming Ballasts

Advance Mark X™ Part No.

REZ-1T32 REZ-1T32 REZ-1T42 REZ-2Q26

REZ-132 REZ-2S32 REZ-3S32

REZ-1TTS40 REZ-2TTS40

TABLE 1

Lamps

CFM26W/GX24Q CFM32W/GX24Q CFM42W/GX24Q

CFQ26W/G24Q

F25T8 F25T8 F25T8 F32T8 F32T8

F32T8 FT40W/2G11 FT40W/2G11

Max. # Ballasts

Single Gang

62 50 39 33 62 32 22 53 27 18 47 24

Cat. No. PE200-7, 277V – For use with Advance Transformer 277V Mark X™ Dimmable Ballasts

Advance Mark X™ Part No.

CFM26W/GX24Q

VEZ-1T32

CFM32W/GX24Q

VEZ-1T32

CFM42W/GX24Q

VEZ-1T42

CFQ26W/G24Q

VEZ-2Q26

VEZ-132 VEZ-2S32 VEZ-3S32

VEZ-1TTS40 VEZ-2TTS40

FT40W/2G11 FT40W/2G11

Wiring Diagram 4: Dual Feed Wiring Application w/Controller

and Two Power Extenders (277V depicted)

Hot (Black) Line (120VAC)

Neutral (White)

Power

Extender

Hot (Black) Line 1 (277VAC)

Neutral (White)

Hot (Black)

Line 2 (277VAC)

Neutral (White)

Dual Feed Wiring: The Input control circuit and the Output load circuit can be supplied by

two circuit breakers on a single phase or by two separate phases.

NOTE:

Up to 4 Power Extenders can be connected together.

NEUTRAL

(Load)

CONTROL

NEUTRAL

LOAD

SWITCH

HOT

Power

Extender

NEUTRAL

(Load)

CONTROL

NEUTRAL

HOT

LOAD

SWITCH

HOT

TABLE 2

Lamps

F25T8 F25T8 F25T8 F32T8 F32T8 F32T8

Max. # Ballasts

Single Gang

98 77 60 52 98 49 34 83 42 29 72 36

Controller/Dimmer

Neutral

Line

Load

Green

Ground

D3206/08

LOAD 1

277V MARK X™

DIMMABLE

BALLAST

LOAD 2

277V MARK X™

DIMMABLE

BALLAST

Wiring Diagram 1A

120V Single Feed Wiring Application w/Mark X™ Ballast

Hot (Black)

(120VAC)

Neutral (White)

Used if Dimmer/Switch has Neutral connection (

(Load)

CONTROL

NEUTRAL

Power

Extender

INPUT

LOAD

OUTPUT

SWITCH

HOT

Single Feed Wiring: Line Hot can be controlled by one circuit breaker as long as

the total load does not exceed the rating of the circuit breakers.

Wiring Diagram 2A

120V Single Feed Wiring Application w/Hi-lume

Hot (Black)

(120VAC)

Neutral (White)

Single Feed Wiring: Line Hot can be controlled by one circuit breaker as long as the total load

does not exceed the rating of the circuit breakers.

Used if Dimmer/Switch has Neutral connection (

(Load)

NEUTRAL

CONTROL

NEUTRAL

Power

Extender

INPUT

LOAD

OUTPUT

HOT

SWITCH

HOT

)

D3206/08

Controller/Dimmer

Neutral Neutral

Line

Load

Green

Ground

120V Mark X™

Line

Load

LOAD

MARK X™

Black

DIMMABLE

BALLAST

White

Ballast

)

120V Mark X™

Type Dimmer

Line

Load

D3206/08

Controller/Dimmer

Neutral Neutral

Line

Load

Green

Ground

LOAD

Orange

Black White

120V Hi-lume

BALLAST

Type Dimmer

Wiring Diagram 3A

277 Dual Feed Wiring Application w/Mark X™ Ballast

Hot (Black)

Line 1 (120VAC)

Neutral 1 (White)

Hot (Black)

Line 2 (277VAC)

Neutral 2 (White)

Dual Feed Wiring: The Input control circuit and the Output load circuit can be supplied by

two circuit breakers on a single phase or by two separate phases.

Used if Dimmer/Switch has Neutral connection (

(Load)

NEUTRAL

CONTROL

Power

Extender

INPUT

LOAD

OUTPUT

HOT

SWITCH

HOT

)

Controller/Dimmer

Neutral

Line

Load

Green

Ground

Black

White

D3206/08

LOAD

277V MARK X™

DIMMABLE

BALLAST

120V Mark X™

Type Dimmer

Neutral

Line

Load

Green

Ground

Wiring Diagram 1B

120V Dual Feed Wiring Application w/Mark X™ Ballast

Green

Ground

Dual Feed Wiring: The Input control circuit and the Output load circuit can be supplied by

two circuit breakers on a single phase or by two separate phases.

Green

Ground

Wiring Diagram 2B

120V Dual Feed Wiring Application w/Hi-lume

Hot (Black)

Line 1 (120VAC)

Neutral 1 (White)

Hot (Black) Line 2 (120VAC)

Neutral 2 (White)

Used if Dimmer/Switch has Neutral connection (

(Load)

NEUTRAL

CONTROL

NEUTRAL

Power

Extender

INPUT

LOAD

OUTPUT

SWITCH

HOT

)

Neutral

Line

Load

Green

Ground

D3206/08

Controller/Dimmer

Orange

120V Hi-lume Black White

LOAD

BALLAST

Ballast

Dual Feed Wiring: The Input control circuit and the Output load circuit can be supplied by

two circuit breakers on a single phase or by two separate phases.

Wiring Diagram 3B

277V Dual Feed Wiring Application w/Hi-lume® Ballast

Hot (Black)

Line 1 (120VAC)

Neutral 1 (White)

Hot (Black)

Line 2 (277VAC)

Neutral 2 (White)

Used if Dimmer/Switch has Neutral connection (

(Load)

NEUTRAL

CONTROL

Power

Extender

INPUT

LOAD

OUTPUT

HOT

SWITCH

HOT

Dual Feed Wiring: The Input control circuit and the Output load circuit can be supplied by

two circuit breakers on a single phase or by two separate phases.

)

Controller/Dimmer

Neutral

Line

Load

Green

Ground

Orange

Black White

D3206/08

LOAD

277V Hi-lume

BALLAST

DI-000-PE200-00A-Pilot

120V Mark X™

Type Dimmer

Neutral

Line

Load

120V Mark X™

Type Dimmer

Neutral

Line

Load

Green

Ground

Green

Ground

Crestron LEPB-2, LEPB-3 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual