Operations & Installation Guide – DOC. 6481 Contents • i
Page 4
Page 5
Crestron IM-TCCV iMedia Table Mount Computer Center with Video
iMedia Table Mount Computer
Center w/Video: IM-TCCV
Introduction
Features and Functions
• A flexible multimedia interface for portable, lectern-mount or undertable installation
• Streamlined user controls for foolproof operation
• iMedia Transport for fast and easy single-cable installation
• Supports XGA resolution up to 84 feet, UXGA maximum up to 34 feet
• Supports composite video signals
• Complete system setup in minutes using iMedia Wizard Software
The iMedia Transport
The iMedia transport utilizes a single CAT5e* type cable to transmit computer RGB,
video, and stereo audio signals to a single projector or plasma display. A typical
XGA signal (1024 X 768 pixels at 60Hz) can be transmitted up to 84 feet using
iMedia, while higher resolutions up to 1600 x 1200 can be handled over shorter
distances. Audio is transmitted digitally at 20-bit, 48 kHz resolution. Control and
power signals are also contained on the same wire, eliminating the need for separate
control or power cables.
* For iMedia use CresCAT-IM cable, or quality CAT5e/CAT6 cable having a maximum delay skew
of 15ns per 100m.
Table Mount Multimedia Interface
The IM-TCCV is an iMedia (IM) transmitter designed to install flush in any flat
surface or underneath a tabletop using the mounting brackets provided. Composite
video, RGB, and stereo audio inputs on the front of the IM-TCCV provide for
connection to the output of a computer or AV source. Installing wiring for the
IM-TCCV is extremely simple requiring just a single CresCAT-IM cable. Up to
three IM-TCCV, or other IM transmitters, may be installed as part of a complete
system to provide multiple input locations within the room.
Operations & Installation Guide – DOC. 6481 iMedia Table Mount Computer Center w/Video: IM-TCCV • 1
Page 6
iMedia Table Mount Computer Center with Video Crestron IM-TCCV
Foolproof Operation
Every iMedia system is easy and intuitive to use. A simple press of the VIDEO or
PC buttons on the face of the IM-TCCV selects the appropriate input, turns on the
projector (or plasma, etc.), lowers the screen or lift, and routes all the signals where
they need to go. The front panel volume control affords easy adjustment of the audio
level, and the entire system can be turned off at any time by simply holding down
either button for five seconds.
For systems having more than one IM transmitter, selecting an input at a given input
location overrides the previously selected input at any other location. The audio level
for each input location is controlled individually by its respective volume control.
Applications
The IM-TCCV is part of the Crestron® iMedia line of network devices, room control
systems and signal routing solutions. The line of iMedia devices includes receivers
and transmitters. Consult the Crestron website for a complete and current listing of
the iMedia product line.
The IM-TCCV can be placed in a lectern or mounted to a surface using the included
brackets.
The IM-TCCV is part of a family of compatible iMedia devices, all capable of
working together to put on simple to complex media presentations. As shown in the
following diagram, iMedia transmitters provide input points for video and PC
sources on an iMedia receiver.
iMedia System Diagram
Computer
Video
IM-TCCV
IM-WCCV
IM-WCCV-S
IM-FTCCV*
iMedia
Transmitter
IM-TCC
IM-WCC
IM-FTCC-B
*IM-FTCCV available 3Q 2006
CresCAT-IM
LAN
IM-RXV1
IM-RXV3
iMedia ReceiverDisplay Device
IR
RS-232
Audio Amplifier
or Speakers
Control
Control
Screen/Lift
Room Sensor
2 • iMedia Table Mount Computer Center w/Video: IM-TCCV Operations & Installation Guide – DOC. 6481
Page 7
Crestron IM-TCCV iMedia Table Mount Computer Center with Video
Specifications
Specifications for the IM-TCCV are listed in the following table.
IM-TCCV Specifications
SPECIFICATION DETAILS
Video Formats
RGB Video
Gain
Max. Input Voltage
Input Impedance
Resolutions
Composite Video
Gain
Max. Input Voltage
Input Impedance
Bandwidth
Audio
Max. Input Level
Input Impedance
Audio Analog/Digital
Conversion
Frequency Response
Power Requirements
Environmental
Temperature
Humidity
Enclosure
Dimensions (without brackets)
Height
Width
Depth
Weight 14.8 oz (420 grams)
RGBHV (VGA), RGBS, RGsB, composite
R/G/B: 0 dB (unity gain, 75 ohm termination)
R/G/B: 1.0 V
R/G/B: 75 Ohms
H/V: 1k Ohms
Supports video up to XGA @ 60 Hz vertical
rate with maximum cable length of 84 feet
and maximum compensation at receiver. For
higher pixel resolutions (up to 1600 X 1200
pixels at 60 Hz vertical rate) refer to the
chart on page 8.
Composite: 0 dB (unity gain, 75 ohm
termination)
1.0 V
PP
75 Ohms
> 100 MHz (-3 dB) at unity gain
2 V
RMS
10k Ohms
20-bit, 48 kHz
20 Hz to 20 kHz
Power is provided by the iMedia receiver via
the IM transport
41° to 104°F (5° to 40°C)
10% to 90% RH (non-condensing)
Compact black metal housing suitable for
portable free-standing use, flush-mounted in
a flat surface, or surface-mounted below a
tabletop using universal brackets provided
1.50 in (3.81 cm)
7.40 in (18.80 cm)
3.13 in (7.95 cm)
H/V: 5 V
PP
PP
Operations & Installation Guide – DOC. 6481 iMedia Table Mount Computer Center w/Video: IM-TCCV • 3
Page 8
iMedia Table Mount Computer Center with Video Crestron IM-TCCV
Physical Description
This section provides information on the connections, controls, and indicators
available on your IM-TCCV.
IM-TCCV Physical View
IM-TCCV Overall Dimensions
145
2
3
7.40 in.
(18.80 cm)
6
1.50 in.
(3.81 cm)
3.13 in.
(7.95 cm)
0.60 in.
(1.53 cm)
1.31 in.
(3.33 cm)
7.08 in.
(17.99 cm)
7.24 in.
(18.38 cm)
4 • iMedia Table Mount Computer Center w/Video: IM-TCCV Operations & Installation Guide – DOC. 6481
Page 9
Crestron IM-TCCV iMedia Table Mount Computer Center with Video
Connectors, Controls, & Indicators
# CONNECTORS,
CONTROLS, &
INDICATORS
1 PC BUTTON
2 VIDEO BUTTON
3 IM
4
5 VIDEO
VOLUME CONTROL
KNOB
DESCRIPTION
Turns on the system and selects the source
connected to the PC input of the IM-TCCV.*
Turns on the system and selects the source
connected to the VIDEO input of the
IM-TCCV.*
(1) Female RJ-45 connector for iMedia
connection to IM-RXV1 or IM-RXV3 receiver
over CresCAT-IM cable or other high-quality
CAT5 wire. For iMedia pin assignments, refer
to the chart on page 8.
Turn clockwise to raise the volume of the
selected input; turn counterclockwise to
lower the volume of the selected input.
(1) RCA-type female connector for composite
video input.
(1) Pair of RCA-type female connectors for
audio feed of composite video input.
6 PC
(1) Female DB15HD connector is used for
connecting a computer’s RGB video output
to the display device.
The following table lists pin assignments:
PIN FUNCTION PIN FUNCTION
1 Red Video 9
2 Green Video 10
3 Blue Video 11
4 Reserved 12
5 Ground 13
6 Red Ground 14
7 Green Ground
8 Blue Ground
15
No Connect
Ground
No Connect
Monitor
Sense 1
Horizontal
Sync
Vertical Sync
Monitor
Sense 2
(1) 3.5mm female mini-jack connects to audio
output of PC.
* Refer to “Operation” on page 13 for more information.
Operations & Installation Guide – DOC. 6481 iMedia Table Mount Computer Center w/Video: IM-TCCV • 5
Page 10
iMedia Table Mount Computer Center with Video Crestron IM-TCCV
Industry Compliance
As of the date of manufacture, the IM-TCCV has been tested and found to comply
with specifications for CE marking and standards per EMC and
Radiocommunications Compliance Labelling.
NOTE: This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
6 • iMedia Table Mount Computer Center w/Video: IM-TCCV Operations & Installation Guide – DOC. 6481
Page 11
Crestron IM-TCCV iMedia Table Mount Computer Center with Video
Setup
Network Wiring
When wiring an iMedia system, consider the following:
• Use Crestron Certified Wire.
• Use Crestron power supplies for Crestron equipment.
IM Wiring
Using a proprietary signal routing solution, RGBHV, composite video, audio, power
and control signals are all transported using a single cable solution called iMedia.
The iMedia transport system port is capable of managing computer RGB, composite
video, and audio signals simultaneously through one CresCAT-IM cable, simplifying
installations.
Routing CresCAT-IM cable (low-skew CAT5e) is less expensive and a much
simpler solution for the wiring of iMedia systems than routing multi-colored, multiconductor coax cable. All Crestron products using the iMedia transport system are
capable of sending and receiving iMedia signals via CresCAT-IM cable. Installation
of any iMedia device is as simple as installing one iMedia cable from output to
input. Installations are affordable, and fast.
Quantity and Packaging
• CRESCAT-IM-P-B500 is a low-skew CAT5e cable, plenum-rated,
available in a 500 foot box
• CRESCAT-IM-P-SP500is a low-skew CAT5e cable, plenum-rated,
available in a 500 foot spool
• CRESCAT-IM-P-SP1000 is a low-skew CAT5e cable, plenum-rated,
available is a 1000 foot spool
For more information on CresCAT and other wire products, visit the Crestron
website (www.crestron.com/features/wire).
Pin Assignments
The pin assignment is based on the EIA/TIA 568B RJ-45 Jack standard.
Power is supplied to the IM transmitters via the audio circuit.
To determine which pin is number 1, hold the cable so that the end of the eight pin
modular jack is facing you, with clip down and copper side up. When looking down
at the copper connections, pin 1 is on the far right.
Operations & Installation Guide – DOC. 6481 iMedia Table Mount Computer Center w/Video: IM-TCCV • 7
Page 12
iMedia Table Mount Computer Center with Video Crestron IM-TCCV
iMedia Pin Assignment
RJ-45 Male Connector RJ-45
Pin
Number
1 White/Orange - RGB Red
2 Orange + RGB Red
3 White/Green - RGB Green
4 Blue + Audio/Power
5 White/Blue - Audio/Power
6 Green + RGB Green
7 White/Brown - RGB Blue / Composite
8 Brown + RGB Blue / Composite
NOTE: Power is supplied to pins 4 and 5 from the IM receivers.
Signal Selection
Wire Colors iMedia Assignment
RGB, Composite and
Audio
The RGB signal connected to the IM transmitter is delivered to the display device
(e.g., projector) via the RGBHV output of an IM receiver. The composite video
signal connected to the IM transmitter is delivered to the display device (e.g.,
projector) via the composite video output of an IM receiver. Each IM transmitter
possesses a SELECT button (IM transmitters with video have two SELECT
buttons) that activates an input. The receiver automatically routes the last activated
input to the RGB or composite video output and deactivates any prior selection. In
addition, the display's power and input selection commands can be controlled via the
IR or COM port.
Video Resolution and Cable Length
The receiver can accomplish frequency compensation on each input to achieve
correct operation. This compensation scheme is effective for CresCAT-IM cables as
long as the maximum skew of 15 ns per 100 m is not exceeded.
NOTE: For proper operations and performance of every iMedia system, always use
CresCAT-IM cable.
Maximum Resolution and Cable Length
RESOLUTION REFRESH
RATE (HZ)
VGA 60 25.18 39.7 218.5
(640 X 480) 72 31.50 31.7 174.6
85 36.00 27.8 152.8
SVGA 56 36.00 27.8 152.8
(800 X 600) 72 50.00 20.0 110.0
85 56.25 17.8 97.8
PIXEL
RATE
(MHZ)
PIXEL TIME
(NS)
MAX
LENGTH
(FEET)
(Continued on following page)
8 • iMedia Table Mount Computer Center w/Video: IM-TCCV Operations & Installation Guide – DOC. 6481
Page 13
Crestron IM-TCCV iMedia Table Mount Computer Center with Video
Maximum Resolution and Cable Length (Continued)
RESOLUTION REFRESH
RATE (HZ)
XGA 60 65.00 15.4 84.6
(1024 X 768) 70 75.00 13.3 73.3
85 94.50 10.6 58.2
SXGA 60 108.00 9.3 50.9
(1280 X 1024) 75 135.00 7.4 40.7
85 157.50 6.3 34.9
UXGA 60 162.00 6.2 34.0
(1600 X 1200) 70 189.00 5.3 29.1
85 229.50 4.4 24.0
COMPOSITE
VIDEO
PIXEL
RATE
(MHZ)
PIXEL TIME
(NS)
MAX
LENGTH
(FEET)
218.5
Installation
The IM-TCCV is designed to mount in a cutout area or to the underside of a
horizontal surface, such as a desktop, lectern, or podium.
NOTE: The IM-TCCV mounting brackets can accommodate virtually any mounting
surface thickness.
Mounting Parts Supplied with the IM-TCCV
PART DESCRIPTION QUANTITY
Screw #8-32 x 1 in, Pan Head, Phillips 2
Mounting Bracket, Right (2012702) 1
Mounting Bracket, Left (2012704) 1
The following assumes that a rectangular cutout for the IM-TCCV (refer to the
cutout dimensions in the following diagram, not drawn to scale) has been made in
the mounting surface. A template is included to provide accurate measurements.
Cutout Diagram
1 13/32 inches (35 mm) Max
7 10/32 inches (185 mm) Max
1. Position the IM-TCCV in the mounting hole.
Operations & Installation Guide – DOC. 6481 iMedia Table Mount Computer Center w/Video: IM-TCCV • 9
Page 14
iMedia Table Mount Computer Center with Video Crestron IM-TCCV
2. Install the left and right brackets:
a. Remove the four rear-most screws from the sides of the IM-TCCV as
shown in the following diagram.
Remove Side Screws
b. Install the left and right brackets using the cover screws as shown in
the following diagram.
Install Brackets
Underside Installation
3. Install the supplied #6-32 screws and tighten the screws until they contact
the backside of the mounting surface but do not over-tighten.
Install Mounting Screw
SCREW
SURFACE WITH CUTOUT
NOTE: Do not over-tighten the screws as this may damage the surface
and/or the unit.
1. Install the left and right brackets:
a. Remove the four rear-most screws from the sides of the IM-TCCV as
shown in the following diagram.
Remove Side Screws
10 • iMedia Table Mount Computer Center w/Video: IM-TCCV Operations & Installation Guide – DOC. 6481
Page 15
Crestron IM-TCCV iMedia Table Mount Computer Center with Video
b. Install the left and right brackets using the cover screws as shown in the
following diagram.
Install Brackets
2. Use a drill/driver to install four #6 hardware screws (not supplied) in the top
holes of the brackets to secure the unit to the underside of the mounting
surface.
Install Hardware Screws
MOUNTING SURFACE
Ventilation
Connect the Device
#6 HARDWARE SCREWS (x4)
NOTE: Do not over-tighten the screws as this may damage the surface
and/or the unit.
Hardware Hookup
To prevent overheating, do not operate this product in an area that exceeds the
environmental temperature range listed in the table of specifications. Consideration
must be given if installed in a closed or multi-unit rack assembly since the operating
ambient temperature of the rack environment may be greater than the room ambient.
Contact with thermal insulating materials should be avoided on all sides of the unit.
Make the necessary connections as called out in the illustrations that follow this
paragraph. Turn on the system only after all connections have been made.
Hardware Connections for the IM-TCCV (Rear)
TO IM-RXV RECEIVER:
CONNECT TO IMEDIA
RECEIVER
Operations & Installation Guide – DOC. 6481 iMedia Table Mount Computer Center w/Video: IM-TCCV • 11
GROUND
Page 16
iMedia Table Mount Computer Center with Video Crestron IM-TCCV
NOTE: For optimum performance, Crestron strongly recommends using
CRESCAT-IM cable, available from Crestron. Other high-quality/low skew
CAT5e/CAT6 wiring may also be used with varying performance.
Hardware Connections for the IM-TCCV (Front)
CONNECT TO COMPOSITE
AUDIO:
VIDEO SOURCE AUDIO
OUTPUT
VIDEO:
CONNECT TO
COMPOSITE
VIDEO
SOURCE
PC:
CONNECT TO
COMPUTER
RGB OUTPUT
AUDIO:
CONNECT TO
COMPUTER
AUDIO OUTPUT
System Configuration
Refer to the latest version of the IM-RXV1 & IM-RXV3 guide (Doc. 6478),
available from the Crestron website (www.crestron.com/manuals) for iMedia system
configuration instructions.
12 • iMedia Table Mount Computer Center w/Video: IM-TCCV Operations & Installation Guide – DOC. 6481
Page 17
Crestron IM-TCCV iMedia Table Mount Computer Center with Video
Operation
The IM-TCCV can be used to turn a system on or off, select a source, or adjust
volume.
Turn on the System
Select a Source
Adjust Volume
Turn off the System
Press the PC button to turn on the system with the PC signals routed to the iMedia
receiver or press the VIDEO button to turn on the system with the video signals
routed to the iMedia receiver. The associated LED will light to indicate the selected
source.
Press the PC button to route PC signals to the iMedia receiver or press the VIDEO
button to route video signals to the iMedia receiver The associated LED will light to
indicate the selected source.
Turn the volume knob clockwise to raise the volume of the selected input; turn
counterclockwise to lower the volume of the selected input.
Press and hold the selected source button for five seconds. The source button LED
will flash and then turn off.
Operations & Installation Guide – DOC. 6481 iMedia Table Mount Computer Center w/Video: IM-TCCV • 13
Page 18
iMedia Table Mount Computer Center with Video Crestron IM-TCCV
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble situations. If
further assistance is required, please contact a Crestron customer service
representative.
IM-TCCV Troubleshooting
TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION
SOURCE LED
does not
illuminate.
No video output
displayed.
No audio output.
Video from RGB
source is garbled or
no output.
Button does not
function when
pressed.
Other functions
operate, but does
not control the
projector.
Not receiving power.
Incorrect power supply.
Source is not selected.
Incorrect cable
connection.
Incorrect cable
connection.
Incorrect cable
connections.
Incorrect cable
connection.
Incorrect connections to
projector.
Verify that the iMedia cable
is connected to the
IM-TCCV.
Only use Crestron power
supplies.
Push a source button on the
IM-TCCV to select a source.
Verify maximum iMedia cable
length. Adjust delay on iMedia
receiver.
Verify that the iMedia output
cable connection from the
IM-TCCV to the iMedia
receiver is secure.
Verify cable wiring and
connections between receiver
and projector.
14 • iMedia Table Mount Computer Center w/Video: IM-TCCV Operations & Installation Guide – DOC. 6481
Page 19
Crestron IM-TCCV iMedia Table Mount Computer Center with Video
Reference Documents
The latest version of all documents mentioned within the guide can be obtained from
the Crestron website (http://www.crestron.com/manuals
of product manuals arranged in alphabetical order by model number.
List of Related Reference Documents
DOCUMENT TITLE
IM-RXV1 & IM-RXV3 iMedia Receiver/Processor with Video
). This link will provide a list
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876].
For assistance in your local time zone, refer to the Crestron website
(http://www.crestron.com/
You can also log onto the online help section of the Crestron website to ask
questions about Crestron products. First-time users will need to establish a user
account to fully benefit from all available features.
) for a listing of Crestron worldwide offices.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of
the IM-TCCV, additional information may be made available as manual updates.
These updates are solely electronic and serve as intermediary supplements prior to
the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
Operations & Installation Guide – DOC. 6481 iMedia Table Mount Computer Center w/Video: IM-TCCV • 15
Page 20
iMedia Table Mount Computer Center with Video Crestron IM-TCCV
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange, or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying
the nature of the problem, name and phone number of contact person, RMA number, and
return address.
2. Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with
RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect
or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its
sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any
products returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials
and workmanship under normal use for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical
parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and
overlay components are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if
any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended, or if it has been subjected to misuse, accidental
damage, modification, or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a
third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are
limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered trademark
of Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft Corporation.
16 • iMedia Table Mount Computer Center w/Video: IM-TCCV Operations & Installation Guide – DOC. 6481
Page 21
Crestron IM-TCCV iMedia Table Mount Computer Center with Video
This page intentionally left blank.
Operations & Installation Guide – DOC. 6481 iMedia Table Mount Computer Center w/Video: IM-TCCV • 17
Page 22
iMedia Table Mount Computer Center with Video Crestron IM-TCCV
This page intentionally left blank.
18 • iMedia Table Mount Computer Center w/Video: IM-TCCV Operations & Installation Guide – DOC. 6481
Page 23
Crestron IM-TCCV iMedia Table Mount Computer Center with Video
This page intentionally left blank.
Operations & Installation Guide – DOC. 6481 iMedia Table Mount Computer Center w/Video: IM-TCCV • 19
Page 24
Crestron Electronics, Inc. Operations & Installation Guide – DOC. 6481
15 Volvo Drive Rockleigh, NJ 07647 (2015046)
Tel: 888.CRESTRON 05.06
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.