Page 1
SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT
Saros® Low Profile & Saros Express Low Profile 2-Way In-Ceiling Speakers
Saros® speakers by Crestron® deliver professional grade
performance and flexible installation in a range of popular
sizes for demanding commercial applications. Solid
construction, easy installation, and high end components
are hallmarks of the complete Saros speaker line.
Ideal for use in background or foreground music, paging,
and sound reinforcement systems, Saros speakers are
engineered to achieve smooth, even coverage, high output,
and clear, natural sound quality through the employment of
horn loaded dome tweeters, high efficiency damped cone
woofers, ported enclosures, and precisely tuned crossovers.
Their low-profile enclosures allow for installation in constricted
ceiling spaces as shallow as 5 1/8 inches (130 mm).
Saros 2-way in-ceiling speakers are available in white or
black and may be painted to blend with the ceiling surface.
quickstart guide
Installation
1
Prepare Mounting Hole
Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air ducts,
joists, or other possible obstructions. If applicable, use a good quality stud finder to locate joists.
If there are no obstructions, use the supplied template to trace an outline of the mounting hole.
For drop tile ceilings, remove the ceiling tile and place on a flat surface to trace the mounting
hole. For drywall or standard construction ceilings, use the template to trace the mounting hole
directly on the ceiling.
Install Cable
Run the cable from the audio source to the speaker location, observing all appropriate local
codes. Strip the ends of the speaker cables approximately 1/8” to 3/16” (~3 mm to ~5 mm) and
twist the strands
.
Install Tile Bridge
The included tile bridge components provide proper support when the speaker is installed in a
typical drop tile ceiling. Refer to the illustration below.
1. Based on the location of the mounting hole determined in “Prepare Mounting Hole” above,
use the two supplied screws to attach the support ring to the rails so that when installed,
the ring is aligned with the mounting hole and the rails rest on the ceiling grid frame.
2. The support ring position on the rails is adjustable to enable off-center speaker positioning.
The tile bridge assembly can be folded to fit through the speaker cutout in blind-mount
situations.
Tile Bridge Assembly
Screws
(Supplied)
Support
Ring
20.91 in
(531 mm)
25.92 in
659 mm
Install/Remove Grille
The zero-bezel frameless grille is held in place by powerful magnets. A safety tether is included to
prevent any possibility of the grille falling from the ceiling. With the tether attached, place the grille
in position on the speaker. To remove the grille, grip the edges and pull away from the speaker.
Paint the Speaker Grille
Speaker grille painting should be done prior to mounting.
1. Carefully remove the material on the underside of the grille and set it aside for reinstallation. It may
be necessary to use a knife or other sharp instrument to free an edge of the material so it can be
peeled away. Use care to avoid cutting or tearing the material.
2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the holes in the grille.
3. Once the paint is dry, reinstall the material to the underside.
Mount/Remove Speaker
The in-ceiling speaker includes four toggle clamps that simplify the mounting process. If the grille is
mounted on the speaker, remove it before proceeding. (Refer to “Install/Remove Grille” above.)
1. Referring to the illustrations to the right, remove the screw securing the rear cover panel, and lift
the cover panel off to expose the supplied terminal block.
2. Route the speaker cable through the cover cable clamp and connect the wires to the terminal
block, using the outer IN terminals: red to + and black to –. Use the inner + and – THRU
terminals to connect a pass-through (parallel) speaker.
3. Allow some slack in the speaker cable(s) and position the cover panel on the back, making
certain it engages the mounting clips. Secure the cover panel using the screw removed in step 1
and tighten the cable clamp to secure the cable(s). Do not over tighten. Use a safety tether
attached to the rear enclosure to prevent the speaker from accidentally falling.
4. The toggle clamps offer two positions to accommodate both standard and extra thick surfaces up
to 2.4 inches (61 mm). For extra thick tiles, reset the toggle clamps to the upper position.
a. With the toggle clamps turned inward, insert the speaker into the opening.
b. Hold the speaker against the ceiling and begin tightening the four screws on the front of the
speaker. The toggle clamps first rotate into clamping position (as indicated in the front view
illustration to the right) and then begin holding the speaker to the ceiling.
c. Tighten the screws until the speaker is secure. Do not over tighten.
5. Speaker removal is accomplished by reversing steps 1 through 4 above.
Set the Transformer Tap Selector Switch
The speakers are equipped with a 70/100 V matching transformer for distributed audio
systems. The transformer tap selector switch on the front panel is used to set the speaker
power level. Use a flat blade screwdriver to adjust the switch.
1. For SAROS_IC6LPT and SAROS_IC8LPT 70 V systems, use the left side settings
and select from 3.75, 7.5, 15, 30, or 60 watts.
2. For SAROS_IC6LPT and SAROS_IC8LPT 100 V systems, use the right side settings
and select from 7.5, 15, 30, or 60 watts. The X position should not be used.
3. For SAROS_ICE6LPT and SAROS_ICE8LPT 70 V systems, use the left side settings
and select from 3.75, 7.5, 15, or 30 watts.
4. For SAROS_ICE6LPT and SAROS_ICE8LPT 100 V systems, use the right side
settings and select from 7.5, 15, or 30 watts. The X position should not be used.
The switch may also be set to 8Ω operation, bypassing the transformer completely. This
setting should be used only for 8 Ω audio systems.
70V
For SAROS_IC6LPT/IC8LPT
70V
For SAROS_ICE6LPT/ICE8LPT
Speaker Cable Connections
IN
THRU
Terminal Block
Not Shown
Front View - Grille Removed
100V
70V
100V
100V
Screw
Safety Tether
Rigging Points
Tighten Screws
SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT
Speaker
Cable
Screw
Terminal
Block
1
QUICKSTART DOC. 7493A (2037420) 11.13
www.crestron.com
Specifications subject to
change without notice.
888.273.7876 201.767.3400
Page 2
SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT
Saros® Low Profile & Saros Express Low Profile 2-Way In-Ceiling Speakers
2
Physical Views
Front View - Grille Removed (Typical)
100V70V
quickstart guide
Rear and Side View (Typical)
Recommended
Cutout Diameter
IN
THRU
Diameter
Minimum
Mounting
Depth
3
Specifications
SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT
SPECIFICATION
Woofer
Tweeter
Crossover Frequency
Impedance
Transformer Taps
Frequency Response
Frequency Range
Power Handling
Sensitivity
Coverage
Connections
Input (1) 4-pin 5 mm detachable terminal block with screw-down flanges;
Speaker input with parallel pass-through;
Maximum Wire Size: 12 AWG
Controls
Transformer Tap (1) Recessed 5-position screwdriver adjustable rotary switch on baffle;
Used to select 70/100 V tap settings or 8Ω (bypass)
Environmental
Temperature -2° to 120° F (-19° to 49° C)
Humidity 5% to 95% RH (non-condensing)
Construction
Enclosure Zinc-plated steel, plenum-rated, side-entry cable clamp
Baffle ABS UL94V-0 plastic
Grille Steel with textured finish, paintable, magnetically-held zero-bezel frameless, safety tether
Mounting Flush ceiling mount using 4 integral 2-step toggle clamps, 2.4 in (61 mm) maximum surface thickness, tile
Dimensions
Diameter
Depth
Recommended
cutout diameter
Minimum mounting
depth
Weight
SAROS_IC6LPT
6.5 in (165 mm)
polypropylene with ring
mode decoupled cloth
surround and steel basket
0.98 in (25 mm) titanium
dome, horn-loaded
2.5 kHz
8 Ω nominal with
transformer set to 8Ω
3.75, 7.5, 15, 30, 60 watts
at 70 V; 7.5, 15, 30, 60
watts at 100 V
65 Hz to 20 kHz (±3 dB)
55 Hz to 20 kHz (-10 dB)
50 watts program, (8 Ω)
88 dB @ (W/m)
95° conical (nominal)
bridge included; (2) Rigging points for safety tether (SPKA-ST-15 sold separately).
10.64 in (270 mm) not
including toggles
5.30 in (135 mm)
9.70 in (246 mm)
5.12 in (130 mm)
8.2 lb (3.7 kg)
SAROS_IC8LPT
8.0 in (203 mm)
polypropylene with ring
mode decoupled cloth
surround and steel basket
0.98 in (25 mm) titanium
dome, horn-loaded
2.5 kHz
8 Ω nominal with
transformer set to 8Ω
3.75, 7.5, 15, 30, 60 watts
at 70 V; 7.5, 15, 30, 60
watts at 100 V
65 Hz to 20 kHz (±3 dB)
55 Hz to 20 kHz (-10 dB)
50 watts program (8 Ω)
90 dB @ (W/m)
95° conical (nominal)
12.13 in (308 mm) not
including toggles
5.30 in (135 mm)
11.20 in (285 mm)
5.12 in (130 mm)
11.1 lb (5.0 kg)
SAROS_ICE6LPT
6.5 in (165 mm)
treated paper with ring
mode decoupled cloth
surround and steel basket
0.98 in (25 mm) treated
cloth dome, horn-loaded
2.5 kHz
8 Ω nominal with
transformer set to 8Ω
3.75, 7.5, 15, 30 watts at
70 V; 7.5, 15, 30 watts at
100 V
85 Hz to 20 kHz (±3 dB)
70 Hz to 20 kHz (-10 dB)
60 watts program (8 Ω)
89 dB @ (W/m)
95° conical (nominal)
10.64 in (270 mm) not
including toggles
5.30 in (135 mm)
9.70 in (246 mm)
5.12 in (130 mm)
9.2 lb (4.2 kg)
SAROS_ICE8LPT
8.0 in (203 mm)
treated paper with ring
mode decoupled cloth
surround and steel basket
0.98 in (25 mm) treated
cloth dome, horn-loaded
2.5 kHz
8 Ω nominal with
transformer set to 8Ω
3.75, 7.5, 15, 30 watts at
70 V; 7.5, 15, 30 watts at
100 V
80 Hz to 20 kHz (±3 dB)
65 Hz to 20 kHz (-10 dB)
60 watts program, (8 Ω)
89 dB @ (W/m)
95° conical (nominal)
12.13 in (308 mm) not
including toggles
5.30 in (135 mm
11.20 in (285 mm)
5.12 in (130 mm)
10.8 lb (4.9 kg)
Problem Solving
4
Troubleshooting
The following table provides corrective action for possible trouble situations. If
further assistance is required, please contact a Crestron customer service
representative.
TROUBLE
No sound or
intermittent
sound is
coming from
the speakers.
Constant noise
such as buzz,
hum, or hiss is
coming from
the speakers.
Low frequency
output is poor.
POSSIBLE CAUSE(S)
There is a cable
connection error.
The amplifier is not
receiving an input
signal or there is a
malfunction.
There is a faulty device
in the system.
There is a system
grounding fault.
There is an incorrect
polarity connection at the
speaker or amplifier.
CORRECTIVE ACTION
Verify the cable connections
between the amplifier and
speakers.
Verify that the amplifier is
functioning correctly, that it is
receiving an input signal, and
that the correct input source
is selected.
Verify that all system devices
are functioning properly.
Verify that system grounding
is correct.
Verify the speaker
connection polarity (+ on
amplifier to + on speaker).
Further Inquiries
To locate specific information or resolve questions after reviewing this guide,
contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876]
or, for assistance within a particular geographic region, refer to the listing of
Crestron worldwide offices at www.crestron.com/offices.
To post a question about Crestron products, log onto Crestron’s Online Help
at www.crestron.com/onlinehelp. First-time users must establish a user
account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features and extends the
capabilities of the SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT, additional
information may be made available as manual updates. These updates are
solely electronic and serve as intermediary supplements prior to the release
of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and
its relevance. Updates are identified as an “Addendum” in the Download
column.
The specific patents that cover crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, and Saros are either trademarks or registered trademarks of
Crestron Electronics, Inc., in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to either
the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible for
errors in typography or photography.
This document was writtren by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT
2
QUICKSTART DOC. 7493A (2037420) 11.13
www.crestron.com
Specifications subject to
change without notice.
888.273.7876 201.767.3400
Loading...