2.21 in.
pigtail
pigtail
CSA-PWS40/CSAI-PWS40
Power Pack for Crestron® CSM-QMTDC Series Roller Shade and Drapery Track Motors
The CSA-PWS40 and CSAI-PWS40 are outlet-mountable, 40 W, 24 VDC regulated power
packs that provide power for Crestron® CSM-QMTDC series roller shade or drapery track
motors. The CSA-PWS40 has a NEMA 1-15P blade insert installed and the
CSAI-PWS40 ships with a blade insert kit that consists of eight blade inserts.
The CSA-PWS40 and CSAI-PWS40 are ideally suited to provide local power for
CSM-QMTDC motors that communicate using the infiNET EX® network.
Check the Box
Item Qty
CSA-PWS40 or CSAI-PWS40 1
CSAI-PWS40 Only
Blade Insert Kit, 8 Blades, International 1
Dimensions
(56 mm)
1.71 in.
(43 mm)
2.91 in.
(74 mm)
1.54 in.
(39 mm)
Install the Power Pack
NOTES:
• Install and use this product in accordance with appropriate electrical codes and
regulations.
• An AC outlet must be located near the CSM-QMTDC series roller shade or drapery
track motor that is powered by the power pack. The power pack has an 8 ft (2.43 m)
long power cable.
Install the power pack:
1. Connect the flying leads from the power pack to the flying leads on the CSM-QMTDC
series roller shade or drapery track motor. Ensure that connections are properly made.
NOTE: To change the plug type on the CSAI-PWS40, refer to the “Change the Blade
Insert” section on the next page.
2. Plug the power pack into a 120 VAC power outlet.
Wiring Diagram Using a Cresnet Motor
Power Pack
24G
To Cresnet
G
Z Y
24
Y
Z
G
Motor
Wiring Diagram Using an infiNET EX Motor
Cresnet motor
Power Pack
24G
Motor
24
G
infiNET EX motor
Change the Blade Insert (CSAI-PWS40 Only)
Additional Information
1. If a blade insert is attached to the CSAI-PWS40, slide the spring-loaded locking key
downward and then pull upward on the blade insert to remove it.
2. Insert the top edge of the blade assembly into the top of the CSAI-PWS40 at
a 30-60 degree angle.
NOTE: The top edge of the blade assembly is flat, and the bottom edge is U-shaped.
The CSAI-PWS40 is shaped similarly.
3. Push the blade insert down into the CSAI-PWS40 until it locks into place. A clicking
sound will occur.
4. Pull up on the blade to check that the blade insert is securely installed.
Technical Specifications
Refer to the CSA-PWS40 product page at www.crestron.com for a complete list of product
specifications.
Specification Details
Output Rating 24 VDC, 40 W (1.66 A), regulated
Power Requirements 1 A @ 100-240 VAC, 50/60 Hz
Connections
Line
Load
Construction 94V-0 polycarbonate, white, outlet-mountable
Environmental
Temperature
Humidity
Weight 6.4 oz (182 g)
(1) power plug, line power input
(1) 8 ft (2.43 m) attached cable with inline ferrite core and
flying leads
32º to 104ºF (0º to 40ºC)
15% to 95% RH (noncondensing)
Scan or click the QR code for detailed product information.
CSA-PWS40 CSAI-PWS40
Compliance and Legal
Original Instructions: The U. S. English version of thi s document is the o rigina l instr uctions. Al l other languag es are a
translation of the original instructions.
As of the date of manufac ture, the produc t has be en tested and fou nd to comply with specif icatio ns for CE ma rking.
This pro duct is listed to applicable UL® Standards and req uireme nts tes ted by Int ertek ® services .
Ce produ it est homologué selo n les nor mes et le s exigen ces UL ap plicables par Interte k Prestations d e serv ice.
Federal Communications Commission (FCC) Compliance Statement
This dev ice comp lies with part 15 of the FCC Rules. Operation is subject to the foll owing co nditions: (1) T his dev ice may
not cause harmfu l interference a nd (2) th is device must accept any interference rece ived, including inter ference that ma y
cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void
the user’s auth orit y to opera te the equipment.
NOTE: This e quipm ent has been tested and found to comp ly with t he limits for a Class B digi tal device, pursuant to
part 1 5 of the FCC Rules. T hese limits are design ed to prov ide reasonabl e protec tion a gains t harmfu l inter ference in a
reside ntial in stallation. This equ ipment g enerates, uses and can ra diate radio frequency e nergy and, if not i nstall ed and
used in accordan ce with the instructi ons, may cause harmful interference to radio comm unicat ions. H owever, there is no
guarantee that i nterference will not occur in a par ticul ar installati on. If this equip ment does cause harmful interference to
radio or televis ion rece ption, which can b e determined by turning the equip ment of f and on, the user i s encouraged to try to
correc t the interfer ence by one or more of t he follo wing me asures :
• Reori ent or rel ocate th e receiv ing ante nna.
• Increase the separation between the equipment and receiver.
• Conne ct the e quipm ent into an o utlet o n a circuit different from t hat to which the receiver is connec ted.
• Consu lt the de aler or an experi enced ra dio/TV technician f or help.
Industry Canada (IC) Compliance Statement
CAN ICE S-3 (B)/N MB-3( B)
The product warranty can be foun d at www.crestron.com/warranty.
The spe cific p atent s that cover Crest ron products are listed at www.crestron.com/legal/patents.
Certa in Crestron product s contain o pen sou rce sof tware. For specific informat ion, pl ease vi sit
www.crestron.com/opensource.
Crestron, the Crestro n logo, and infiNET EX ar e either tradem arks or registered tra demarks of Cres tron Ele ctronics, I nc.
in the United States and/or oth er count ries. T he ETL l ogo is either a tra demar k or regis tered t rademark of Inte rtek Test ing
Serv ices NA in the United States and/or othe r countr ies. UL is eithe r a trademark or re gistered trad emark of U nder writers
Laboratories, Inc. i n the Uni ted State s and/or other countries. O ther tr ademarks, re gistered trademarks, and trade names
may be us ed in this document to refer to eithe r the entities cl aiming t he mark s and nam es or the ir produ cts . Crestron
discla ims any pro prieta ry interest in t he mark s and nam es of othe rs. Crestron is not resp onsible for erro rs in ty pography or
photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Dr ive, Rockleigh , NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Do c. 7370D
Specifications subject to
change without notice.
(2053450)
05/15/1 9
Loading...