Crestron CEN-IO-RY-204, CEN-IO-IR-204, CEN-IO-COM-202, CEN-IO-DIGIN-204 User Manual

CEN-IOWireless Series

The Crestron® CEN-IO-COM-202, CEN-IO-DIGIN-204, CEN-IO-IR-204,
and CEN-IO-RY-204 are wireless I/O modules designed to expand the
available control ports within a commercial or residential system. The
modules communicate to the local network over Wi-Fi® wireless
communications for remote control and monitoring.

NOTE:The CEN-IO-COM-202, CEN-IO-DIGIN-204, CEN-IO-IR-204,

and CEN-IO-RY-204 are functionally similar. For simplicity within this
guide, the term "wireless module"is used to refer to all models except
where otherwise noted.

Quick Start

Mount the Device

The wireless module can be mounted onto a flat surface or a standard
DIN rail using the included mounting bracket.

CAUTION:To prevent overheating, do not operate this product in an

area that exceeds the environmental temperature range (41 to 104 °F
or 5 to 40 °C) for this device.

Optional rack mount and pole mount kits (not included)are also available
for use with the wireless module. For more information, refer to the
RMK-IFE-1U Installation Guide (Doc. 7627) and the PLMK-IFE-101
Installation Guide(Doc. 7615) at www.crestron.com/manuals.

In the Box

1 CEN-IO-COM-202, CEN-IO-DIGIN-204, CEN-IO-IR-204, or

CEN-IO-RY-204, Wireless Network Module

Additional Items

1 Bracket, Mounting, Integrated DINRail Clip (4510935)
1 Connector, 2-Pin (2003574)
1 Power Pack, PW-0512WUL (2045867)
2 Screw, 6-32, 3/8 in., Phillips(2007225)

CEN-IO-COM-202 Only

2 Connector, 5-Pin (2003577)

CEN-IO-DIGIN-204 Only

1 Connector, 5-Pin (2003577)

CEN-IO-IR-204 and CEN-IO-RY-204 Only

1 Connector, 8-Pin (2003850)

SurfaceMounting

1. Attach the mounting bracket to the surface using four appropriate
mounting screws (not included) and the four mounting holes on the
bottom of the bracket.

2. Align the slots on the bottom of the wireless module with the tabs on
the mounting bracket.

3. Press the wireless module into the bracket until it snaps into place.

1

CEN-IOWireless Series

Quick Start

4. (Optional) Secure the wireless module to the bracket using the two
included 6-32 3/8 in. screws as shown in the following illustration.

DINRail Mounting

1. Pull the DIN rail release tab downward using a flat-head screwdriver.

2. Position the DIN rail mounting tabs (located on the rear of the
bracket) over the top edge of the DIN rail.

3. Push the DIN rail release tab upward to lock the mounting bracket
onto the rail.

4. Align the slots on the bottom of the wireless module with the tabs on
the mounting bracket.

5. Press the wireless module into the bracket until it snaps into place.

NOTE:Do not use the included screws to secure the bracket to the

bottom of the wireless module when mounting into a DINrail, as it will
then not be possible to remove the wireless module from the DIN rail.

2

CEN-IOWireless Series

Connect the Device

Make all device connections as shown in the following illustrations.

CEN-IO-COM-202 Rear Panel Connections

Quick Start

CEN-IO-DIGIN-204 Rear Panel Connections

CEN-IO-IR-204 Rear Panel Connections

3