Page 1
CE-600
AM-200, AirMedia® Presentation
System 200
CBL-USB-A-BMICRO-6, 6′ USB A
to Micro B Cable
IRP2, IR Emitter Probe
with Terminal Block Connector
ZUMMESH-AVBRIDGE, Wireless Control
Integration Module
ZUMMESH-PIR-OCCUPANCY-BATT,
Occupancy Sensor
Workplace Technology Solution – Open Presentation Space
The CE-600 Open Presentation Space workplace technology solution includes a
Crestron® AM-200 AirMedia® Presentation System 200, sensors, and the cables required
to provide conference room capabilities and room schedule information.
Wireless
Occupancy
Display
Sensor
AV Bridge
RS-232
USB
HDMI
AM-200
LAN
CAT5e
quickstart guide
Preparation
1
Verify Contents
Check the table below for the system's package contents before starting
installation. The following items are included:
QUANTITY ITEM PART NUMBER
2
Connect the System
AM-200 (Top View)
LAN
Connect an HDMI cable (sold separately) to the HDMI INPUT port and to the source device’s HDMI output port.
Connect the CBL-HD-6 cable to the HDMI OUTPUT port and to the display device’s HDMI input port.
Connect the CBL-USB-A-BMICRO-6 cable to the USB port and to the COMPUTER port on the ZUMMESH-AVBRIDGE.
Connect a CAT5e cable (sold separately) to the LAN PoE port and to the corporate LAN.
NOTE: The AM-200 can receive power from the included power pack or from PoE supplied to the LAN PoE port.
Connect the PW-2407WU power pack (included with the AM-200) to the 24V 0.75A port.
Connect the AM-200 to earth ground.
1
1
1
1
1
1
Additional Requirements
A video display (sold separately) must be connected to the HDMI OUTPUT port
on the AM-200.
Optional Accessory
A TSW-series touchscreen and/or wireless keypad can be added for system
control. For details, refer to the AM-200/300 product manual at
www.crestron.com/manuals.
1
QUICKSTART DOC. 8312A (2051278) 04.18
CBL-HD-6, 6′ HDMI® Cable
Zūm™ Wireless Battery-Powered
6509936
6503565
6508229
6500126
6507997
6507983
AM-200 (BottomView)
www.crestron.com
Specifications subject to
change without notice.
888.273.7876 201.767.3400
Connect the IRP2 emitter probe to the IR1 port
and to the display device.
Connect a serial cable (sold separately) to the
COM port and to the display device.
NOTE: The IR1 and COM ports should only be
connected if the display device does not respond
to CEC commands via the HDMI connection. If
using the IR1 and COM ports, set the display
device model in the AM-200’s web-based setup
pages. For details, refer to the AM-200/AM-300
product manual (Doc. 8254) at
www.crestron.com/manuals.
CE-600
Page 2
CE-600
ZUMMESH-AVBRIDGE
Connect the CBL-USB-A-BMICRO-6 cable to the COMPUTER port and to the USB port on the AM-200.
quickstart guide
3
Apply Power
When all connections are made, apply power to all of the devices in the system.
Workplace Technology Solution – Open Presentation Space
4
1
5
Add the Occupancy Sensor to the System
Perform the following procedure to join the ZUMMESH-PIR-OCCUPANCY-BATT to the ZUMMESH-AVBRIDGE.
NOTE: The following procedure assumes the ZUMMESH-PIR-OCCUPANCY-BATT has already been installed
as described in the ZUMMESH-PIR-OCCUPANCY-BATT Installation Guide (Doc. 7867).
1. On the ZUMMESH-AVBRIDGE, press the SETUP button 5 times, then press and hold the SETUP button
until the LED on the device lights (about 10 seconds). After approximately 3 seconds, the device LED
begins slowly flashing, indicating that is in Joining mode.
NOTE: Only one ZUMMESH-AVBRIDGE should be in Joining mode at a time.
NOTE: Joining mode ends automatically after 4 minutes.
2. Remove the cover from the ZUMMESH-PIR-OCCUPANCY-BATT.
3. On the ZUMMESH-PIR-OCCUPANCY-BATT, press the TEST button 3 times, then press and hold the TEST
button until the LED on the device lights (up to 10 seconds). The device is joined to the
ZUMMESH-AVBRIDGE.
4. On the ZUMMESH-AVBRIDGE, press the SETUP button to exit Joining mode.
More Information
For more information, refer to the documents below. All documents can be found at www.crestron.com/manuals.
• AM-200 DO Guide (Doc. 8260)
• AM-200/AM-300 Product Manual (Doc. 8254)
• IRP2 Installation Guide (Doc. 8186)
• ZUMMESH-AVBRIDGE Installation Guide: (Doc. 7916)
• ZUMMESH-PIR-OCCUPANCY-BATT Installation Guide (Doc. 7867)
CE-600
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/legal/open-source-software.
Crestron, the Crestron logo, AirMedia, and Zūm are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and
trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
2
QUICKSTART DOC. 8312A (2051278) 04.18
www.crestron.com
Specifications subject to
change without notice.
888.273.7876 201.767.3400
Loading...