DO GUIDE
Keyed washer
Flat washer
Thread cables
through here.
Standard Wiring Zoom Wiring
Cable retention bracket
Route HDMI
CCS-UCA-SMK
Swivel Mount Kit for Crestron Mercury™ Tabletop Conference System
DO Prepare the Mounting Location
NOTE: The mounting surface should have a thickness of 1" (25 mm) to 1-3/8" (34 mm).
The kit includes a template that is used to mark the location of the mounting hole on top of the mounting surface, and the location of the stop plate under the
mounting surface. When using the template, make sure the arrow on the template points toward the front edge of the mounting surface.
1. Secure the template to a mounting location that allows the full pivot of the device on the top of the mounting surface and a close mounting location for
accessories beneath the mounting surface.
2. Place 2" painters tape (not included) on the hole location and mark the hole on the tape.
3. Drill a 1-3/16" (30 mm) mounting hole in the marked location on the tape.
4. Relocate the template to the underside of the mounting surface and orient it so that the arrow on the template points toward the front edge of the table.
Verify that the template location of the stop plate permits the Crestron Mercury™ device to swivel.
DO Install the Cable Retention Bracket
NOTE: If a cable retention plate is already installed, it must be removed. For new installations, skip to step 3. Otherwise, follow this procedure:
1. Use two small at head screwdrivers to slowly pry off the existing retention plate.
2. Remove all adhesive residue from the surface.
3. Clean the surface with an alcohol wipe (not supplied).
4. Remove the paper liner from the back of the cable retention bracket.
5. Install the cable retention bracket as shown in the following diagram.
Cable retention bracket
DO Check the Box
QUANTITY PRODUCT COLOR PART NUMBER
1 Bit, Slotted 1/4" W 2049730
1 Bit, Slotted 23/64" W 20 49474
1 Bracket, Cable Retention 4526653
1 Cable, HDMI, Male to Female Extender 2049637
4 Insert, Metal, M7, 6-32 Thread, 0.28" L 2049476
2 Insert, Metal, M10, 10-32 Thread, 0.41" L 2049328
2 Nu t , 1-1/8"-12 2049390
2 Screw, 4-40 x 1/4", Pan Head, Phillips Black 200715 8
2 Screw, 6-32 x 1/2", Pan Head, Phillips Black 2007238
2 Screw, 6-32 x 1", Truss Head, Phillips Black 2049649
6 Screw, 8-8B x 1/2", Pan Head, Phillips 201778 4
2 Screw, 8-32 x 1/8", Cap Head, Socket Black 2017634
2 Screw, 10-32 x 1", Pan Head, Phillips Black 2049391
1 Stop Plate, Swivel, with Screws 4526651
1 Template, Cutout 4526654
5 Tie Wrap 2047935
1 Washer, Cork, 2.0" OD, 1.19" ID, 0.06" TH 2049448
1 Washe r, Keyed 4526609
1 Washer, Metal, 2.0" OD, 1.19" ID, 0.10" TH 2049389
1 Washer, Rubber, 2.0" OD, 1.19" ID, 0.06" TH 2049449
If the Crestron Mercury device’s HDMI OUT port is to be used, perform the following procedure:
a. Connect the HDMI Extension Cable (2049637) to the HDMI OUT port.
b. Route the cable extender through the swivel tube.
c. Connect the HDMI cable provided with the Crestron Mercury device to the cable extender.
4. Make the necessary connections to the device. Refer to the DO Guide or Installation Guide included with the Crestron Mercury system.
5. Use the included tie wraps to secure all of the cables to the cable retention bracket that was installed in “DO Install the Cable Retention Bracket.”
6. Press rmly on the cable retention bracket for approximately 30 seconds.
CAUTION : When turning over the device, place the device on a soft surface to avoid damage to the unit.
DO Connect the Device
1. Drill pilot holes with a 1/8" bit in the stop plate’s mounting location and attach the stop plate to the underside of the mounting surface with the six
included 8-8B x 1/2" screws.
2. Place the swivel tube plate on the mounting surface.
3. Route all cables that connect to the Crestron Mercury device from underneath the mounting surface through the swivel kit hardware as shown below.
Cables with larger connectors should be routed rst, followed by cables with smaller connectors.
Stop plate
Nuts (2)
Permanently installed
limiting screws
If the HDMI® input cable and the USB cable are to be routed to the front of the Crestron Mercury device, do not route these cables through the swivel kit
hardware.
Rubber washer
Cork washer
6. If the front USB and HDMI input connections are to be used, press the USB and HDMI IN cables into the channels on the underside of the device as
shown in the following diagram (cables removed for clarity) so that the connectors can be routed to the front of the device.
Route USB
cable here
cable here
DO Attach the Swivel Tube Plate to the Device
Screws (2) 6-32 x 1/2"
Screws (2) 6-32 x 1" or
Screws (2) 10-32 x 1"
(see following
Permanently installed
20' HDMI cable with service loop Tie wrap
Inserts (2) M7
NOTE: A manual bit screwdriver (not included) is required for this procedure.
1. Install the inserts as shown in the following diagram (cables removed for clarity).
CAUTION : Ensure that all screws are fully seated to avoid damage to the mounting surface.
NOTE: Use the screws that t the inserts installed in step 1.
NOTE: To avoid bending the swivel tube plate, do not overtorque the screws.
DO Customize the Swivel Range (Optional)
Two additional 8-32 x 1/8" screws are included to further customize the swivel range. Refer to the
following illustrations for details on customizing the swivel range.
Inserts (2) M7 or
Inserts (2) M10
(see following NOTES)
NOTE: Due to variances in manufacturing, these insert locations use either the small diameter
inserts or the large diameter inserts. Use the inserts (and matching screws) that t into the holes in
the device’s chassis.
NOTE: The M7 inserts drop down into the two center holes in the base prior to tightening.
a. Place the correct insert in the proper location with the slotted end on top.
b. Use a manual bit screwdriver to secure the inserts to the Crestron Mercury device by turning
each insert until it locks itself snugly into the base.
• For the smaller insert, use the included 1/4" slotted bit to turn the insert.
• For the larger insert, use the included 23/64" slotted bit to turn the insert.
2. Refer to the following diagram (cables removed for clarity) to attach the swivel tube plate to the
device.
Screws (2) 4-40 x 1/4"
DO Secure the Device to the Mounting Surface
1. Slide the included hardware onto the swivel tube as shown in the following diagram (cables removed
for clarity).
Stop plate
Screws (2) 8-32 x 1/8"
Stop plate
Screws (6) 8-8B x 1/2"
Keyed washer
Flat washer
limiting screws
Cork washer
Rubber washer
Nuts (2)
90˚
Tab of keyed metal washer
where swivel motion starts
45˚
Four locations for additional
limiting screws. Place
limiting screws to limit the
amount of swivel to the
desired range.
60˚
Permanent
limiting screws
60˚
120˚
DO Complete the Installation
If the HDMI cable extender was used, connect the HDMI output cable to the HDMI cable extender. Use
tie wraps on both ends of the connection to secure the cable connection to the other cables exiting the
swivel tube.
Swivel tube plate
NOTES)
As of the date of manufacture, the product has been tested a nd found to compl y with specic ations for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device com plies with par t 15 of the FCC Rules. Op erati on is subject to th e following two conditions:
(1) This devic e may not cause harmful interferenc e, and (2) this devic e must ac cept any inter feren ce received, includi ng inter fere nce tha t may cause undesired o perat ion.
CAUTION: Changes or modication s not expr essly approve d by the manufacturer re sponsible fo r compliance c ould voi d the use r’s authority to operate the equi pment .
NOTE: This equipment has been tested and found to comply with the lim its for a Class B digital device, pursuant to par t 15 of the FCC Ru les. These lim its are d esign ed to provide rea sonab le prote ction
agains t harmful interference in a reside ntial installation. This equipment gene rates, uses an d can radiate rad io freq uency e nergy and, if not installed an d used in a ccordance with the instruc tions, may
cause harmful inter feren ce to radio communications. However, there i s no guar antee that interference will not occur in a par ticu lar ins tallation.
If this equipment does c ause ha rmful i nterference to radio or television re cepti on, which can be d etermined by turning th e equip ment of f and on, the user is encourage d to try to c orrect the interfe rence
by one or more of the following m easures:
• Reorient or relocate the receiving antenna.
• Increase the separation bet ween the equip ment and receiver.
• Connect the equipment into an outlet on a c ircuit diffe rent from that to w hich the receiver is connecte d.
• Consult the dea ler or an experience d radio/T V technician fo r help.
NOTE: The keyed washer limits the swivel range to approximately 180 degrees. The swivel range
can be further limited by installing additional cap screws in the stop plate. Refer to “DO Customize
the Swivel Range” for instructions.
2. Tighten the upper nut to achieve the desired resistance in the swivel motion. Use a at tool, such as
a large, at-head screwdriver in the slot on the bottom of the swivel tube to hold the tube in place
while tightening the nut.
3. Manually tighten the lower nut to the upper nut to prevent the upper nut from slipping.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Crestr on product develop ment softwar e is licensed to Cres tron dealers and C restron Ser vice Providers ( CSPs) under a limit ed non-exclusive, no n-transfera ble Softwar e Development Tools Lic ense Agreement. C restron produ ct operating sys tem software i s licensed to Cres tron dealers, C SPs, and
end-user s under a separate E nd-User Licens e Agreement. Bot h of these Agreemen ts can be found on the C restron websit e at www.crestron.com/legal/soft ware_license_agreement.
The speci c patents that c over Crestron pro ducts are listed a t www.crestron.com/legal/patents. The produ ct warranty ca n be found at www.crestron.com/legal/sales-terms-conditions-warranties.
Certa in Crestron pro ducts contain op en source soft ware. For speci c information, vi sit www.crestron.com/legal/open-source-software.
Crestr on, the Crestro n logo, and Crest ron Mercury are e ither trademar ks or registered t rademarks of Cre stron Electr onics, Inc., in the U nited States a nd/or other coun tries. HDMI is e ither a trademar k or registered tr ademark of HDM I Licensing LLC in t he United Stat es and/or other co untries. Oth er
trademar ks, registered tr ademarks, and tr ade names may be used in th is document to refer to e ither the entitie s claiming the marks an d names or their produ cts. Crestron d isclaims any propri etary interes t in the marks and name s of others. Crest ron is not respons ible for errors in t ypography or
photography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2017 Crestron Electronics, Inc.
Tie wrap
HDMI cable extender
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn more
about this product, use a QR reader application on your mobile device to scan the QR
image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
DO GUIDE
DOC. 78 82B ( 204 9471) 10.17
Specic ations subject to c hange without not ice.
Loading...