Crestron BB-6000 User Manual

Crestron BB-6000 Back Box

Contents

Back Box: BB-6000 1

Description ..........................................................................................................................1

Installation...........................................................................................................................2

Construction Method..............................................................................................2

Post-Construction Method ......................................................................................4

Further Inquiries................................................................................................................... 6

Cutout Detail of Supplied Template ...................................................................................... 7

Return and Warranty Policies ............................................................................................... 8

Merchandise Returns / Repair Service.....................................................................8

CRESTRON Limited Warranty............................................................................... 8

Installation Guide - DOC. 5826 Contents •• i

Crestron BB-6000 Back Box

Back Box: BB-6000

Description

The back box, BB-6000, is the mounting hardware that secures a Crestron Series

6000 Lectern/Wall Mount Touchpanel to a wall or other suitable mounting surface.

Supplied Components

DESCRIPTION PART NUMBER QUANTITY

Metal Electrical Box with 8 knockouts AY17463-1 1
Metal Mounting Bracket MTBK02552-1 2
Metal Mounting Plate MTPL02523-1 2
Screw, 6-32 x 1"L, pan, phillips, black SR06-32-1R000-3 12
Screw, 6-32 x 1/2"L, pan, phillips, zinc SR06-32-0R5000-4 6
Template OV40052-1 1

Three views and dimensions for the metal pieces of the BB-6000 are shown below.

BB-6000 Physical Views and Dimensions

13.766 in

12.706 in

(34.966 cm)

(32.273 cm)

2.500 in

(6.350 cm)

4.930 in

(12.522 cm)

13.955 in

(35.446 cm)

3.500 in

(8.890 cm)

*

*

*

3.625 in

(9.208 cm)

3.500 in

(8.890 cm)

*

*

*

Installation Guide - DOC. 5826 Back Box: BB-6000 •• 1

Back Box Crestron BB-6000

BRACKETS

Installation

There are at least two different methods of installing the BB-6000. The construction

method is initiated during the construction process. Use this method to wall mount a

Crestron Series 6000 Lectern/Wall Mount Touchpanel to a wall stud. Installation

begins at a time when the rooms in which the panel is to be installed are framed and

the gypsum board has not been hung. The post-construction method is preferred for

wall mounting when the rooms are complete and the gypsum board has already been

hung. The post-construction method is also desirable when lectern mounting the

panel.

Construction Method

The only equipment and tools required are three #6 mounting screws (or equivalent),

a drill with adjustable torque, a #2 Phillips tip bit, a 5/16” drill bit, and a #20 drill bit.

Complete the following installation procedure in the order provided.

1. Remove necessary knockout(s) from metal electrical box.

2. Use six pan head screws (1/2” length), supplied, to loosely secure two

metal brackets to the back box.

Attaching Two Metal Brackets to the Back Box

PAN

HEAD

SCREWS

3. Position the metal electrical box to the stud. If 5/8" gypsum board is

used, be sure that ½" of the box protrudes from the stud as illustrated in
the metal electrical box cut away shown after this step.

METAL

2 •• Back Box: BB-6000 Installation Guide - DOC. 5826

Crestron BB-6000 Back Box

Securing Metal Electrical Box to Stud

STUD

SCREW

HOLES

0.50 in

(1.27 cm)

4. Use three #6 screws, not supplied, to secure metal electrical box to the

stud.

5. Pull Cresnet wire through open knockout(s) in the metal electrical box.

NOTE: Wait for gypsum board to be hung before continuing with remainder of

construction method installation.

6. Fasten template, supplied, to mounting surface; cut out and remove the

traced shape.

7. Drill four 5/16” holes as marked on template. Only drill through

gypsum board. Use caution and do not drill through metal bracket that
rests behind gypsum board. Refer to "Cutout Detail of Supplied
Template" on page 7 for an illustrative reference.

8. Drill 12 holes marked “A” on template with #20 bit. Only drill through

gypsum board. Use caution and do not drill through metal bracket that
rests behind gypsum board. Refer to "Cutout Detail of Supplied
Template" on page 7 for an illustrative reference.

9. Position one metal mounting plate along the top horizontal edge so that

it covers the two center holes marked “A”.

10. Use two pan head screws (1” length), supplied, to loosely secure the

bracket and plate to the mounting surface.

11. Position one metal mounting plate along the bottom horizontal edge so

that it covers the two center holes marked “A”.

12. Use two pan head screws (1” length), supplied, to loosely secure the

bracket and plate to the mounting surface.

Installation Guide - DOC. 5826 Back Box: BB-6000 •• 3

Back Box Crestron BB-6000

13. Tighten four screws installed in steps 10 and 12 by hand. Be careful not

to crack gypsum board.

14. Verify that the rim of the back box is recessed approximately 1/8" from

the mounting surface and tighten six screws installed in step 2 with a
torque of 11 in-lbs (1.243 N*m).

15. If touchpanel is available, secure touchpanel to BB-6000 using eight

pan head screws (1” length), supplied. Tighten screws by hand being
careful not to crack gypsum board.

Post-Construction Method

The only tools required are a gypsum board saw (or equivalent), a drill with

adjustable torque, a #2 Phillips tip bit, a 5/16” bit, and a #20 bit. Complete the

following installation procedure in the order provided.

1. Locate an area on the wall or other suitable mounting surface that is

clear of studs, wires, and other obstructions.

2. Make a small hole near the middle of the designated site; verify

location is suitable.

3. Fasten cutout template, supplied, to mounting surface; verify that the

template is level.

4. Cut out and remove the traced shape of mounting surface.

5. Drill four 5/16” holes as marked on template. Refer to "Cutout Detail

of Supplied Template" on page 7 for an illustrative reference.

6. Drill 12 holes marked “A” on template with #20 bit. Refer to "Cutout

Detail of Supplied Template" on page 7 for an illustrative reference.

7. Slide one metal mounting bracket through the opening and position it

inside along the top horizontal edge.

8. Position one metal mounting plate along the top horizontal edge so that

it covers the two center holes marked “A”.

9. Use two pan head screws (1” length), supplied, to secure the bracket

and plate to the mounting surface. Tighten by hand; do not fully tighten
screws.

4 •• Back Box: BB-6000 Installation Guide - DOC. 5826

Crestron BB-6000 Back Box

CENTER TAPPED HOLES)

Securing Bracket/Plate Assembly to Top and Bottom Edges of Opening

MOUNTING

BRACKET

DRYWALL

METAL

METAL

MOUNTING

PLATE

TWO PAN

HEAD

SCREWS

(MOUNTS BRACKET
AND PLATE IN TWO

10. Repeat steps 7 through 9 for the bottom horizontal edge of the opening.

11. Remove necessary knockout(s) from metal electrical box.

12. Pull Cresnet wire through open knockout(s) in metal electrical box.

13. Slide the electrical back box through the opening until the rim of the

back box is flush with the mounting surface.

NOTE: Do not slide the back box too far into the opening or it may fall in between

the gypsum board (e.g., if installation is into an exterior wall).

Positioning Back Box into Opening

METAL

ELECTRICAL

BOX

DRYWALL

Installation Guide - DOC. 5826 Back Box: BB-6000 •• 5

Back Box Crestron BB-6000

14. Tighten four screws installed in steps 9 and 10 by hand. Be careful not

to crack gypsum board.

15. Use six pan head screws (1/2” length), supplied, to loosely secure the

back box to the bracket plate assembly.

Securing Back Box to Bracket/Plate Assembly

PAN HEAD

SCREWS

Further Inquiries

0.125 in

(0.317 cm)

DRYWALL

16. Verify that the rim of the back box is recessed approximately 1/8" from

the mounting surface before tightening the six pan head screws with a
torque of 11 in-lbs (1.243 N*m).

17. If touchpanel is available, secure touchpanel to BB-6000 using eight

pan head screws (1” length), supplied. Tighten screws by hand being
careful not to crack gypsum board.

If after reviewing this Installation Guide for the BB-6000, you cannot locate specific

information or have questions, please take advantage of Crestron's award winning

technical support team by calling:

• In the US and Canada, call Crestron’s corporate headquarters at

1-888-CRESTRON [1-888-273-7876] or 1-201-767-3400.

• In Europe, call Crestron International at [phone].

• In Asia, call Crestron Asia at [phone].

• In Latin America, call Crestron Latin America at [phone].

For local support from exclusive Crestron factory-trained personnel call:

• In Australia, call Soundcorp at [phone].

• In New Zealand, call Amber Technologies at [phone].

6 •• Back Box: BB-6000 Installation Guide - DOC. 5826

Crestron BB-6000 Back Box

Cutout Detail of Supplied Template

15.125 in

(38.418 cm)

A A A

5/16" DRILL

UNIT CUTOUT

( NOT FOR MOUNTING TPS-6000LW OR TPS-6000LB)

CRESTRON

A A A

A A A

ALL HOLES MARKED "A"
#20 DRILL (

.161)

TEMPLATE

FOR BB-6000

A A A

13.300 in

(33.782 cm)

Installation Guide - DOC. 5826 Back Box: BB-6000 •• 7

Back Box Crestron BB-6000

Return and Warranty Policies

Merchandise Returns / Repair Service

1. No merchandise may be returned for credit, exchange, or service

without prior authorization from CRESTRON. To obtain warranty
service for CRESTRON products, contact the factory and request an
RMA (Return Merchandise Authorization) number. Enclose a note
specifying the nature of the problem, name and phone number of
contact person, RMA number, and return address.

2. Products may be returned for credit, exchange, or service with a

CRESTRON Return Merchandise Authorization (RMA) number.
Authorized returns must be shipped freight prepaid to CRESTRON,
Cresskill, N.J., or its authorized subsidiaries, with RMA number clearly
marked on the outside of all cartons. Shipments arriving freight collect
or without an RMA number shall be subject to refusal. CRESTRON
reserves the right in its sole and absolute discretion to charge a 15%
restocking fee, plus shipping costs, on any products returned with an
RMA.

3. Return freight charges following repair of items under warranty shall

be paid by CRESTRON, shipping by standard ground carrier. In the
event repairs are found to be non-warranty, return freight costs shall be
paid by the purchaser.

CRESTRON Limited Warranty

CRESTRON ELECTRONICS, Inc. warrants its Cresnet products, denoted by a

"CN" prefix model number, to be free from manufacturing defects in materials and

workmanship for a period of three (3) years from the date of shipment to purchaser.

Disk drives and any other moving or rotating mechanical parts are covered for a

period of one (1) year. CRESTRON warrants all its other products for a period of

one year from the defects mentioned above, excluding touchscreen display

components which are covered for 90 days. Incandescent lamps are completely

excluded from Crestron's Limited Warranty. CRESTRON shall, at its option, repair

or replace any product found defective without charge for parts or labor. Repaired or

replaced equipment and parts supplied under this warranty shall be covered only by

the unexpired portion of the warranty.

CRESTRON shall not be liable to honor warranty terms if the product has been used

in any application other than that for which it was intended, or if it has been

subjected to misuse, accidental damage, modification, or improper installation

procedures. Furthermore, this warranty does not cover any product that has had the

serial number altered, defaced, or removed.

This warranty shall be the sole and exclusive remedy to the purchaser. In no event

shall CRESTRON be liable for incidental or consequential damages of any kind

(property or economic damages inclusive) arising from the sale or use of this

equipment. CRESTRON makes no other warranties nor authorizes any other party to

offer any warranty, expressed or implied, including warranties of merchantability for

this product. This warranty statement supersedes all previous warranties.

Trademark Information

All brand names, product names, and trademarks are the sole property of their respective owners.

Windows is a registered trademark of Microsoft Corporation. Windows95, Windows98 and WindowsNT

are trademarks of Microsoft Corporation.

8 •• Back Box: BB-6000 Installation Guide - DOC. 5826