Crest audio CA9-X SPECIFICATIONS
CA9-X
POWER AMPLIFIER
Preliminary Product Description
The Crest Audio CA9-X professional power amplifier is
designed to achieve unsurpassed sonic performance and longterm reliability—even when operating under extreme stress—in
touring or fixed installation applications.
Absolute sonic accuracy is the hallmark of every Crest amplifier.
Bass is solid and defined to the limits of audibility, with ample
current reserves delivered by an “over-engineered” power supply
and advanced Class H circuitry. Wide-bandwidth output devices
assure detailed, transparent high frequency response. And, thanks
to Crest’s exclusive IGM circuit, the CA9-X will drive loads
safely without compromise in performance.
Construction and Quality Control
The CA9-X is built exclusively in Crest’s own USA manufacturing facility, with internal components selected for premium quality and proven durability. Each modular subassembly is pre-tested, and the assembled CA9-X receives a rigorous “hot room”
burn-in before thorough final checkout on precision test equipment.
CA9-X Features
• Crest’s legendary “overbuilt” power supply
• Toroidal power transformer
• Latest generation of high-speed, wide-bandwidth output
devices
• Twin tunnel cooling with back-to-front air flow
• Dual, variable speed DC fans
• Massive, extruded aluminum heat sinks
• Balanced XLR and 1/4-inch (TRS) inputs
• 5-Way binding post outputs or Speakon™ connectors
(market dependent)
• Stereo/parallel/bridged mono mode selector switch
• Ground lift switch
•
TourClass
- ACL (Active Clip Limiting) prevents speaker damage with
- IGM (Instantaneous Gain Modulation) monitors speaker
- AutoRamp gradually increases gain to attenuator setting
- TourClass also includes comprehensive thermal manage-
• Input sensitivity selection
• Recessed, stepped attenuators
• Front panel circuit breaker switch
• Modular construction
• Five-year warranty*
®
protection circuits:
gentle gain reduction at clip threshold.
loads to detect conditions that may overstress output
devices, allowing safe operation.
level when amplifier is turned on.
ment, and short circuit, DC voltage, turn-on/off transient,
current inrush and sub/ultrasonic input protection.
Power Specifications 8Ω Stereo 4Ω Stereo 8Ω Bridged
1kHz, 0.01% THD+N 600W 900W 1800W
20Hz-20kHz, 0.1% THD+N 550W 800W 1600W
Figures are watts per channel, both channels driven.
CA9-X POWER AMPLIFIER
PRELIMINARY SPECIFICATIONS
1kHz, 0.01% THD+N 20Hz-20kHz, 0.1% THD+N
8Ω Stereo Power
4Ω Stereo Power
8Ω Bridged Mono Power
Max RMS Output Voltage
(each channel)
Peak Output Voltage (each channel)
Frequency Response (+0 / -0.3dB, 1W/8Ω)
Power Bandwidth (rated power at 4Ω, 1% THD+N)
TourClass®Protection
THD+N
(rated power at 4Ω, 1kHz)
SMPTE IMD (rated power at 8Ω, 60Hz & 7kHz)
Damping Factor (10-400Hz at 8Ω)
Input CMRR (1kHz)
Input Sensitivity (rated power at 8Ω )
Voltage Gain
Input Impedance (balanced/unbalanced)
Hum and Noise
(“A” weighted, full power, 4Ω)
Crosstalk (“A” weighted, full power, 4Ω)
Input Connectors
(per channel)
Output Connectors (per channel)
Filter Storage
Power Supply
(factory configured)
Idle Current Draw 120V
1/8 Power Curr. Draw
(typical music, 120V/4Ω)
1/3 Power Curr. Draw (continuous music, 120V/4Ω)
Max Curr. Draw (circuit breaker rating, 120V/4Ω)
Thermal Emissions (1/8 Power, 4Ω)
Thermal Emissions (1/3 Power, 4Ω)
Controls
LED Indicators
(per channel)
Construction
Dimensions
(Height x Width x Depth)
Gross Weight, Net Weight
Warranty
Dealer-Configurable Gain/Sensitivity Options Factory Standard X47.4 1.40V
600W 550W
900W 800W
1800W 1600W
82V
116V
20Hz-20kHz, -3dB@135kHz
20Hz-20kHz, -.84dB/+0dB
ACL, IGM, AutoRamp, short circuit, DC voltage,
turn-on/off transient, current inrush, sub/ultrasonic input.
<0.01%
<0.01%
700:1
> - 60dB
1.40V standard (see table below)
X47.4 standard (see table below)
>20kΩ/>10kΩ
-105dB
> - 60dB
Class
H
Female XLR (pin 2+, dealer configurable for pin 3+), TRS (tip+)
5-way output binding posts or Speakon connectors
80,000 µF
100V-240V, 50-60Hz
2.0A
8.6A
16.0A
30A
3250 BTU/hr
4341 BTU/hr
Cooling
Back-to-front via 2 rear panel mounted variable-speed DC fans
(filters removable without tools)
Front Panel: 2 attenuators, located behind blanking plugs
Rear Panel: signal ground lift switch, mode select switch
Clip/Limit, Signal, Temp/DC, Active
Steel chassis, 16 gauge. Double thickness in rack ear areas.
3.5" x 19" x 18" / 89 x 483 x 457mm
52lbs. (23.60 kg.), 47 lbs. (21.33 kg.)
*
5 years
Gain Sens
Option 1 X40.0 1.66V
Option 2 X20.0 3.32V
(market dependent)
Architect’s & Engineer’s Specifications
The power amplifier shall have two channels. At 8 ohms, 20Hz
- 20kHz, 0.1% THD+N, it shall deliver a minimum of 550 watts
per channel. At 4 ohms, 20Hz - 20kHz, 0.1% THD+N, it shall
deliver a minimum of 800 watts per channel. In bridged mono
mode with an 8 ohm load, 20Hz - 20kHz, 0.1% THD+N, it
shall deliver a minimum of 1600 watts.
The amplifier shall have circuitry to protect itself from output
short circuits, thermal overload or other adverse load conditions. The amplifier shall protect speaker loads from DC voltage on outputs. The amplifier shall have active clip limiting
and impedance sensing circuitry. Output relays shall protect
the speakers from amplifier failure.
Two rear panel mounted variable speed DC fans (filters
detachable without tools) shall provide back to front air flow
through the chassis.
Each channel shall have a standard (factory-set) input sensitivity of 1.40 Volts, and shall be fitted with an internal jumper
which allows the gain to be altered to X20 or X40. The hum
and noise level shall be 105 dB below rated output, “A”
weighted. SMPTE IMD shall be less than 0.01% at rated
power, 60Hz and 7kHz. The amplifier shall have a class H output stage. The frequency response shall be 20Hz-20kHz, +0,
-0.3dB (1W/8Ω).
The amplifier will operate at 100V-240V, 50-60 Hz AC (configured at factory). Maximum current draw shall not exceed 30
amperes at 120VAC (limited by front panel breaker for bench
tests).
Front panel indicators shall include Active, Protect, Signal,
and Clip LED’s for each channel. Front panel attenuators
shall be detented and located behind blanking plugs.
Rear panel input connectors shall be female TRS and XLR
type, internally dealer-configurable for pin 2 (factory setting)
or pin 3 positive. Output terminations shall be 5-way output
binding posts or Speakon output connectors (market dependent). A ground lift switch and a Stereo/Parallel/Bridged Mono
mode operation switch shall be provided.
A rear-panel IEC AC mains socket (with power cord) or single
AC mains cord having an appropriate AC plug for the intended
operating voltage shall be provided (market dependent).
The packaging of the amplifier shall allow for standard rack
mounting without requiring space between similar units.
Optional rack mount handles will be available. Dimensions
shall be 19" (483mm) wide, 3.5" (89mm) high and 18"
(457mm) deep. The amplifier shall weigh 47 lbs. (21.33 kg.)
net, and shall be designated the Crest Audio model CA9-X.
Power figures are watts per channel, both channels driven.
* 3-Year Warranty with 2 additional years if Registration Card
is sent to Crest Audio. (USA,
Canada, United Kingdom, and
many other countries).
Crest Audio reserves the right to
make improvements in manufacturing or design which may affect
specification.
Crest Audio specification literature is available in downloadable
PDF format; visit our website at:
http://www.crestaudio.com.
©1997 Crest Audio Inc.
v. 1.0 08/13/97
Rear View,
Binding Post
Version
Rear View,
Speakon
Version
(not available in
North America)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS : RISQUE DE CHOC ÉLECTRIQUE—NE PAS OUVRIR
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
ATTENTION! POUR ÉVITER LE RISQUE D'INCENDIE OU DE CHOC
ÉLECTRIQUE, NE PLACEZ PAS CET APPAREIL SOUS LA PLUIE OU Á
L'HUMIDITÉ
A
A
+
+
A
B
+
B
NL4FC
A
A
B
B
A
•
•
AB
A
+
A
B
••
A
B
B
A
B
A
A
•
•
AB
A
+
A
B
•
•
B
A
B
A
B
Designed & manufactured in the USA by:
Crest Audio Inc.
100 Eisenhower Dr.
Paramus, New Jersey 07652 USA
2+
1
3-
643-105
Designed & manufactured in the USA by:
Crest Audio Inc.
100 Eisenhower Dr.
Paramus, New Jersey 07652 USA
2+
1
3-
Crest Audio Inc.
100 Eisenhower Dr., Paramus NJ 07652 USA
TEL: 201.909.8700 FAX: 201.909.8744
http://www.crestaudio.com
Loading...