Cres Cor H-339-X-128-C-240 Installation Manual

5925 Heisley Road • Mentor, OH 44060-1833

OPERATING and MAINTENANCE INSTRUCTIONS

For INSULATED UNDERCOUNTER CABINETS

MODEL H-339-X-C Series

ELECTRICAL SPECIFICATIONS:

MODEL Volts Watts Amps Hertz Phase NEMA

H-339-X-128C,

UA-8C, 188C,

12-188C, 1813C

H-339-X-128C-240,

188C-240, 12-188C-240,

1813C-240, UA-8C-240

HOW TO INSTALL UNIT:

Plug cord into 15-amp wall outlet.1.
Place cabinet in a well ventilated area.2.
Insert pan slides into the cabinet.3.
Push the switch on, turn the thermostat to No. 10 4.
and run the unit for one hour.

120 900 7.5 60 1 5-15

240 900 3.8 60 1 6-15

Insulated

Holding Cabinet

Rev. 1 (4/06) Page 1 of 4

FL-2300

NOTE: DO NOT PUT IN FOOD!

This step is to burn off manufacturing oils and
excessive adhesive.

Let the cabinet cool and wipe inside clean with 5.
detergent and hot water before use.

HOW TO OPERATE UNIT: (Figure 1)

Push switch “ON”. Yellow light will come on. 1.
Turn thermostat to the temperature you need.2.

NOTE: No. 7½ setting will give you about 180° F.

Proper food holding temperature is 140° F or
higher.

Preheat cabinet for 45 minutes3.
Put food into cabinet.4.
Turn the wing nut on the door vent to open the 5.
vent when less humidity is needed.

To Turn Off Unit:

Push switch “OFF”. The yellow light will go off.
NOTE: Thermometer gives the inside cabinet

temperature.

Figure 1

Control Panel

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

Insulated

Holding Cabinet

Rev. 1 (4/06) Page 2 of 4

FL-2300

5925 Heisley Road • Mentor, OH 44060-1833

MAINTENANCE INSTRUCTIONS

WARNING

BEFORE CLEANING CABINET:

Unplug power cord from wall.1.
Do NOT hose cabinet with water.2.
Do NOT get water on controls.3.
Do NOT use abrasives or harsh chemicals. 4.

SOIL CLEANER METHOD

DIRT

CABINET

Inside and

Outside

(Aluminum)

FINGERPRINTS,

WATER SPOTS Mild abrasive cleaner. Wipe with damp cloth.

GREASE OIL

*Mild detergents include soaps and non-abrasive cleaners.

Hints:

Wipe up spills as soon as possible. 1.
Clean cabinet regularly to avoid heavy dirt build-up.2.
Make a test spot with cleaner.3.
Follow manufacturer’s directions on cleaner.4.
Do not mix cleaners5.
Avoid drips and splashes.6.

Mild detergent* and hot water, or
mild abrasive cleaner.

Steam (no strong alkaline additive) 1. Rinse after steam cleaning.

Detergent* and hot water 1. Wipe with soft, damp cloth.

Chemical oven cleaner for
aluminum

Mild abrasive cleaner.
Oily or waxy cleaner.

1. Use soft, damp cloth.

2. Rinse with hot water.

3. Wipe dry.

2. Wipe dry.

2. Rinse with hot water.

3. Wipe dry.
Follow oven cleaner

manufacturer’s directions.
Apply with soft, clean cloth.

HOW TO ADJUST THE DOOR LATCH:

For vertical adjustment 1.
(Up and down movement):

a. Loosen (2) screws located in magnetic

strike on cabinet.

b. Move strike up or down for alignment to

magnet on latch.

c. Tighten screws to secure

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

2. For horizontal adjustment
(Greater or lesser magnetic draw):

a. Loosen four (4) screws in latch on door.
b. Move latch forward or backward to adjust

magnetic draw.

c. Tighten screws to secure.