Cres Cor H-339214 User Manual

5925 Heisley Road • Mentor, OH 44060-1833

OPERATING and MAINTENANCE INSTRUCTIONS

For INSULATED HAND-LIFT CABINET; MODEL H-339214

ELECTRICAL SPECIFICATIONS:

MODEL Volts Watts Amps Hertz Phase NEMA

H-339214 120 900 7.5 60 1 5-15

SWITCH LIGHT

“ON-OFF”

THERMOSTAT

THERMOMETER

Insulated

Hand-lift Cabinet

Rev. 3 (10/08) Page 1 of 4

FL-0520-12

DOOR

VENT

HOW TO INSTALL UNIT:

Plug cord into 20-amp wall outlet.1.
Place cabinet in a well ventilated area.2.
Push the switch on, turn the thermostat to No. 10 3.
and run the unit for one hour.

NOTE: DO NOT PUT IN FOOD!
This step is to burn off manufacturing oils and
excessive adhesive.

4. Let the cabinet cool and wipe inside clean with
detergent and hot water before use.

FIGURE 1

HOW TO OPERATE UNIT: (Figure 1)

Push switch “ON”. Yellow light will come on.1.
Turn thermostat to the temperature you need.2.

NOTE: No. 7½ setting will give you about 180° F.

Proper food holding temperature is 140° F or
higher.

3. Preheat cabinet for 45 minutes

4. Put food into cabinet.

5. Turn the wing nut on the door vent to open the vent
when less humidity is needed.

To Turn Off Unit:

Push switch “OFF”. The yellow light will go off.
NOTE: Thermometer gives the inside cabinet

temperature.

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

Insulated

Hand-lift Cabinet

Rev. 3 (10/08) Page 2 of 4

FL-0520-12

OPERATING and MAINTENANCE INSTRUCTIONS

For INSULATED HAND-LIFT CABINET; MODEL H-339214

WARNING

5925 Heisley Road • Mentor, OH 44060-1833

BEFORE CLEANING CABINET:

1. Unplug power cord from wall.

2. Do NOT hose cabinet with water.

3. Do NOT get water on controls.

4. Do NOT use abrasives or harsh
chemicals.

HOW TO CLEAN UNIT:

SOIL CLEANER METHOD

ROUTINE CLEANING

CABINET

STUBBORN SPOTS

Inside and Outside

(Stainless Steel)

AND STAINS
BURNT-ON FOODS

OR GREASE
HARD WATER

SPOTS and SCALE

* Mild detergents include soaps and non-abrasive cleaners

Hints:

Wipe up spills as soon as possible. 1.
Clean cabinet regularly to avoid heavy dirt build-up.2.
Make a test spot with cleaner.3.
Follow manufacturer’s directions on cleaner.4.
Do not mix cleaners5.
Avoid drips and splashes.6.

Soap, Ammonia, or mild* detergent
and water

Mild abrasive made for stainless steel

Chemical oven cleaner for stainless
steel

Vinegar

1. Sponge on with cloth.

2. Rinse with water.

3. Wipe dry.

1. Apply with damp sponge or cloth.

2. Rub lightly.
Follow oven cleaner

manufacturer’s directions.

1. Swab or wipe with cloth.

2. Rinse and dry.

HOW TO ADJUST THE DOOR LATCH:

1. For vertical adjustment
(Up and down movement):

a. Loosen (2) screws located in magnetic

strike on cabinet.

b. Move strike up or down for alignment

to magnet on latch.

c. Tighten screws to secure

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

2. For horizontal adjustment
(Greater or lesser magnetic draw):

a. Loosen four (4) screws in latch on door.
b. Move latch forward or backward to

adjust magnetic draw.

c. Tighten screws to secure.