Cree LP377TYL1-70G-01 Service Manual
Subject to change without notice.
www.cree.com/ledlamps
查询LP377TYL1-70G-01供应商
Cree® P4 LED
Model # LP377TYL1-70G-01
Data Sheet
70-degree, 7.6 x 7.6 mm LED lamp in amber color with water-transparent lens and stopper
Applications
Advertising Signs
•
Indicators
•
Trafc Signals
•
Automotive Lighting
•
Absolute Maximum Ratings (TA = 25°C)
Items Symbol Absolute Maximum Rating Unit
Forward Current
Peak Forward Current
Reverse Voltage V
Power Dissipation P
Operation Temperature T
Storage Temperature T
Lead Soldering Temperature T
Note 2
Note 1
I
F
I
FP
R
D
opr
stg
sol
70 mA
200 mA
5 V
220 mW
-40 ~ +100 °C
-40 ~ +100 °C
Max. 260°C for 3 sec. max.
(3 mm from the base of the epoxy bulb)
Notes:
Pulse width ≤0.1 msec, duty ≤1/10.
1.
A heat sink is recommended if the device is operated at ambient temperatures higher than 25°C.
2.
Typical Electrical & Optical Characteristics (TA = 25°C)
Characteristics Symbol Condition Unit Minimum Typical Maximum
Forward Voltage V
Reverse Current I
Dominant Wavelength λ
0
0
0
.
3
3
1
T
C
D
L
C
:
t
e
Luminous Flux Φ
50% Power Angle 2θ½ IF = 70 mA deg 70
e
h
S
a
t
a
D
F
R
D
V
IF = 70 mA V 2.6 3.2
VR = 5 V μA 100
IF = 70 mA nm 584 591 599
IF = 70 mA mlm 2000 3200
1
Standard Bins for LP377TYL1-70G-01 (IF = 70 mA)
Lamps are sorted to luminous ux (ΦV), VF and dominant wavelength (λD) bins shown.
Orders for LP377TYL1-70G-01 may be lled with any or all bins contained as below.
All luminous ux (ΦV), VF and dominant wavelength (λD) values shown and specied are at IF = 70 mA.
X2 X3 X4 X5 X6
L or
above
K
J
H
G
584 nm
587 nm
590 nm
593 nm
596 nm
599 nm
Dominant Wavelength (λD)
Rank G H J K
Luminous Flux
2000-3000 mlm 2500-3600 3000-4200 mlm 3500-4800 mlm
Forward Voltage (VF)
Rank
Voltage
V4 V5 V6 V7 V8
2.2-2.4 V 2.4-2.6 V 2.6-2.8 V 2.8-3.0 V 3.0-3.2 V
Important Notes:
All ranks will be included per delivery; rank ratio will be based on the dice distribution.
1.
No tolerance of measurement of luminous ux.
2.
Tolerance of measurement of dominant wavelength is ±1 nm.
3.
Tolerance of measurement of VF is ±0.05 V.
4.
Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” docu-
5.
ment.
Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions.
6.
Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED
7.
product safely.
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks of Cree, Inc.
2 CLD-CT133.000
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Fax: +1.919.313.5778
www.cree.com/ledlamps
Loading...