Cree LP377PBL1-60G-03 Service Manual
Subject to change without notice.
www.cree.com/ledlamps
查询LP377PBL1-60G-03供应商
Cree® P4 LED
Model # LP377PBL1-60G-03
Data Sheet
60-degree, 7.6 x 7.6 LED lamp in blue color with water-transparent lens and stopper
Applications
Advertising Signs
•
Indicators
•
Message Boards
•
Absolute Maximum Ratings (TA = 25°C)
Items Symbol Absolute Maximum Rating Unit
Forward Current I
Peak Forward Current
Reverse Voltage V
Power Dissipation P
Operation Temperature T
Storage Temperature T
Lead Soldering Temperature T
Note
F
I
FP
R
D
opr
stg
sol
30 mA
100 mA
5 V
132 mW
-40 ~ +95 °C
-40 ~ +100 °C
Max. 260°C for 3 sec. max.
(3 mm from the base of the epoxy bulb)
Note: Pulse width ≤0.1 msec, duty ≤1/10.
Typical Electrical & Optical Characteristics (TA = 25°C)
Characteristics Symbol Condition Unit Minimum Typical Maximum
Forward Voltage V
Reverse Current I
Dominant Wavelength λ
Luminous Flux Φ
50% Power Angle 2θ½ IF = 30 mA deg 60
0
0
0
.
5
1
1
T
C
D
L
C
:
t
e
e
h
S
a
t
a
D
F
R
D
V
IF = 30 mA V 3.6 4.4
VR = 5 V μA 100
IF = 30 mA nm 462 470 475
IF = 30 mA mlm 250 850
1
Standard Bins for LP377PBL1-60G-03 (IF = 30 mA)
Lamps are sorted to luminous ux (ΦV ), VF and dominant wavelength (λD) bins shown.
Orders for LP377PBL1-60G-03 may be lled with any or all bins contained as below.
All luminous ux (ΦV ), VF and dominant wavelength (λD) values shown and specied are at IF = 30 mA.
X2 X3 X4
E or
)
V
Luminous Flux (Φ
above
D
C
B
460 nm
565 nm
470 nm
475 nm
Dominant Wavelength (λD)
Rank B C D
Luminous
Flux
Rank
Voltage
2.8-3.0 V 3.0-3.2 V 3.2-3.4 V 3.4-3.6 V 3.6-3.8 V 3.8-4.0 V 4.0-4.2 V 4.2-4.4 V
250-500 mlm 400-800 mlm 600-1200 mlm
V7 V8 V9 V10 V11 V12 V13 V14
Important Notes:
All ranks will be included per delivery; rank ratio will be based on the dice distribution.
1.
No tolerance in the measurement of luminous ux.
2.
Tolerance of measurement of dominant wavelength is ±1 nm.
3.
Tolerance of measurement of VF is ±0.05 V.
4.
Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” docu-
5.
ment.
Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions.
6.
Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED
7.
product safely.
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks of Cree, Inc.
2 CLD-CT115.000
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Fax: +1.919.313.5778
www.cree.com/ledlamps
Loading...