PIVOT HUTCH
Thank you for purchasing the Pivot Hutch. This page
lists all the contents included in the box. Please take
time to identify the hardware as well as the individual
components of this product. As you unpack and prepare
for assembly, place the contents on a carpeted or
padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
HARDWARE
32 - bolts 32 - spring
washers
2 - connecting
brackets
4 - large
screws
4 - plastic anchors
Missing hardware? Please call
800.606.6387 for replacements.
TOOLS REQUIRED
phillips head screwdriver
32 - flat
washers
4 - medium
screws
8 - small
screws
8 - shelf
pins
2 - wall
straps
4 - wall
brackets
COMPONENTS
1 - top
panel
1 - front
frame
1 - bottom
panel
1 - back
panel
2 - adjustable
shelves
2 - side panels
(1 left, 1 right)
Made in Vietnam - r03 Page 1 of 5
1 - partition
Customer Service 800.967.6696 | www.crateandbarrel.com
PIVOT HUTCH
partition
bottom
panel
NOTE: Make sure “THIS SIDE UP” labeled
on bottom panel is facing toward the
partition when assembling as shown
1 Attach bottom panel and partition with 2 bolts, 2
spring washers, and 2 flat washers as shown.
Secure bolts with a phillips head screwdriver.
back panel
2 Fit dowels of partition into corresponding holes of
back panel as shown.
left side
panel
right side
panel
3 Attach left/right side panels to assembled unit
with 6 bolts, 6 spring washers, and 6 flat washers
as shown.
Made in Vietnam - r03 Page 2 of 5
Customer Service 800.967.6696 | www.crateandbarrel.com
4 Secure left/right side panels to bottom panel of
assembled unit with 4 bolts, 4 spring washers, and 4
flat washers as shown.
PIVOT HUTCH
frame
support
front
frame
front
frame
5 Remove frame support from front frame as shown.
With a screwdriver, turn pre-attached bolts
counter-clockwise to detach. Set frame support and
hardware aside and discard.
top
panel
NOTE: Make sure arrow
labeled “FRONT” on
underside of top panel is
pointing towards the front
6 Fit dowels of assembled unit into corresponding
holes of front frame. Secure front frame with 6 bolts,
6 spring washers, and 6 flat washers as shown.
A
A
B
adjustable
shelves
7 With the assistance of another adult, position
assembled unit upright as shown. Attach top panel to
assembled unit with 14 bolts, 14 spring washers, and
14 flat washers as shown.
Made in Vietnam - r03 Page 3 of 5
Customer Service 800.967.6696 | www.crateandbarrel.com
8 A) Insert 8 shelf pins as desired heights as shown.
B) Place 2 adjustable shelves into assembled unit as
shown. Make sure each shelf is securely supported by each
shelf pin.
PIVOT HUTCH
7 With the assistance of another adult, carefully place
hutch onto buffet as shown. Attach 2 connecting
brackets to back of hutch and buffet (sold seperately)
with 4 small screws per bracket as shown. Secure
screws with a screwdriver.
Assembly is now complete.
hutch
(sold seperately)
buffet
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
Made in Vietnam - r03 Page 4 of 5
Customer Service 800.967.6696 | www.crateandbarrel.com
PIVOT HUTCH
Safety Mounting Instructions
C
plastic
anchor
For added safety and stability, it is recommended
that the wall mounting hardware be installed. For
safe mounting, it is essential to use wall anchors
appropriate to your wall type (i.e. plaster, drywall,
concrete, etc.). Mount to wood studs whenever
possible.
A) Attach wall bracket to top of bookcase using 2
medium screws as shown.
B) Determine the final location of bookcase. Mark
position on the wall, approximately 2" below the
wall bracket mounted to the back of the cabinet.
C) Drill a hole in the wall stud. If the wall stud is
not available, drill a hole in the wall that is slightly
smaller in diameter than the anchor. Gently tap the
plastic anchor until the flange of the anchor is
flush with the wall.
D) Attach wall bracket to the wall by inserting 2
large screws, and into the plastic anchor in the
wall.
E) Place the unit so the wall brackets on the back
edge are aligned with the wall brackets on the wall.
F) Lace one end of the wall strap through both
brackets, and into the other end of the strap.
G) Pull the strap tightly until secure.
H) Repeat steps A-G for remaining wall brackets
and wall straps.
wall
bracket
D
large
screw
A
medium
screw
F
wall
strap
wall
bracket
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
Made in Vietnam - r03 Page 5 of 5
Customer Service 800.967.6696 | www.crateandbarrel.com
Loading...