PAYTON 20” X 76” BOOKCASE
ASSEMBLY HARDWARE
Thank you for purchasing the Payton 20” x 76” Bookcase. This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
screws
14 - bolts25 - back
20 - wood
dowels
12 - shelf
pins
WALL MOUNTING HARDWARE
1 - wall strap
Missing hardware? Please call 800.606.6387 for replacements.
1 - plastic
anchor
1 - wall
screw
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead power tools)
1 - top panel
2 - side panels
(1 left, 1 right)
3 - adjustable
shelves
Made in China - r03 Page 1 of 3
1 - fixed
shelf
1 - back panel
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
1 - bottom
panel
1 - crossbar
bottom
B
panel
fixed
C
shelf
1 A) Insert 4 wood dowels into crossbar as shown.
B) Insert 8 wood dowels into bottom panel as shown.
C) Insert 4 wood dowels into fixed shelf as shown.
D) Insert 4 wood dowels into top panel as shown.
A
crossbar
D
top panel
PAYTON 20” X 76” BOOKCASE
A
crossbar
NOTE: Do not over
tighten the bolts
B
fixed shelf
left side
panel
C
bottom
panel
2 A) Fit dowels of crossbar into corresponding holes of
left side panel as shown.
B) Fit dowels of fixed shelf into corresponding holes of
left side panel. Secure fixed shelf to left side panel with
2 bolts as shown, using a phillips head screwdriver. Do
not over tighten the bolts.
C) Fit dowels of bottom panel into corresponding holes
of left side panel. Secure bottom panel to left side
panel with 2 bolts as shown.
A
crossbar
right side
panel
B
fixed shelf
bottom
panel
C
3 A) Fit dowels of crossbar into corresponding holes of
right side panel as shown.
B) Fit dowels of fixed shelf into corresponding holes of
right side panel. Secure fixed shelf to right side panel
with 2 bolts as shown.
C) Fit dowels of bottom panel into corresponding holes
of right side panel. Secure bottom panel to right side
panel with 2 bolts as shown.
top panel
4 Fit dowels of top panel into corresponding holes of
assembled unit as shown. Secure top panel to
assembled unit with 6 bolts as shown.
NOTE: Do not attach back screw
into back panel at this point if
installing optional safety mounting.
Please refer to Optional Safety
Mounting Instructions.
NOTE: Do not over
tighten the screws
back panel
5 Attach back panel to assembled unit with 25 back
screws as shown. Secure, but do not over tighten, the
screws using a screwdriver.
Made in China - r03 Page 2 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
PAYTON
shelf
A
pin
adjustable
B
shelf
20” X 76” BOOKCASE
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the wood is finished with a protective clear lacquer.
METHOD TO ADJUST LEVELERS ON
BOOKCASE
leveler
6 A) With the assistance of another adult, position unit
upright. Insert 12 shelf pins at desired shelf heights as shown.
B) Place 3 adjustable shelves onto shelf pins as shown.
Make sure shelves are securely supported by each shelf pin.
Assembly is now complete.
NOTE: Please do the following if your bookcase
is not level.
With the assistance of another adult, adjust
levelers of each leg as necessary.
OPTIONAL SAFETY MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that the wall
mounting hardware be installed. For safe mounting, it is essential
to use wall anchors appropriate to your wall type (i.e. plaster,
drywall, concrete, etc.). Mount to wood studs whenever possible.
A. Drill a pilot hole in the wall stud. If the wall stud is not available,
drill a hole in the wall that is slightly smaller in diameter than the
anchor. Gently tap the plastic anchor until the flange of the anchor
is flush with the wall.
B. Insert wall screw through end of wall strap and into plastic
anchor in the wall.
C. Insert back screw through end wall strap and into the top back
of unit as shown.
NOTE: Insert screws 3/4"-1"
from the edge of the strap
wall
strap
back
screw
WALL
plastic
anchor
Mounting assembly is now complete.
wall
screw
NOTE: If you are unsure about your wall type or what mounting
method you should use, consult a qualified professional or your
local hardware store.
Made in China - r03 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3 of 3
Loading...