Thank you for purchasing the Paterson Corner Media
Stand. This page lists all the contents included in the
box. Please take time to identify the hardware as well as
the individual components of this product. As you
unpack and prepare for assembly, place the contents on
a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
6 - cam
dowels
12 - large
screws
Missing hardware? Please call 800.606.6387 for replacements.
screws
2 - barrel
nuts
10 - small
bolts
6 - cams
2 - large
bolts
4 - shelf
pins
4 - pull bolts26 - wood
4 - hinges
WALL MOUNTING HARDWARE
2 - wall
straps
2 - wall
brackets
2 - anti-tip
brackets
2 - plastic
anchors
2 - large
screws
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead power tools)
24 - small
screws
4 - small
screws
1 - top panel
2 - small side panels
(1 left, 1 right)
Made in China - r13Page 1 of 6
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
2 - large side panels
1 - base
1 - shelf
2 - doors
(1 left, 1 right)
1 - back panel
2 - pulls
PATERSON CORNER MEDIA STAND
NOTE: Do not over
tighten the bolts
top panel
A
B
base
NOTE: Do not over
tighten the cam screws
1 A) Fit 13 wood dowels into top panel as shown.
B) Insert 6 cam screws into base as shown. Secure, but
do not over tighten, cam screws using a phillips head
screwdriver.
back panel
large
side panel
top panel
NOTE: Make sure
ledge on panel is
positioned as shown
2 Fit pre-installed dowels of top panel into corresponding holes of large side panel. Secure large side panel
with 2 small bolts as shown, using a phillips head screwdriver. Do not over tighten the bolts.
NOTE: Make sure
ventilation holes of panel
are positioned as shown
3 Fit pre-installed dowels of top panel into corresponding
holes of back panel. Secure back panel with 2 small bolts as shown.
large
side panel
4 Fit pre-installed dowels of top panel into corresponding
holes of remaining large side panel. Secure large side panel with 2 small bolts as shown.
Made in China - r12Page 2 of 6
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
PATERSON CORNER MEDIA STAND
NOTE: Do not over
tighten the screws
left small
side panel
right small
side panel
left small
side panel
5 Secure left and right small side panels to top panel
with 2 small bolts per side as shown.
base
C
NOTE: Make sure
hole of barrel nut
aligns with the
hole in nearest
edge
A
right small
B
side panel
A
back panel
6 A) Secure large side panels to left/right small panels
and back panel with 6 large screws as shown, using a
phillips head screwdriver. Do not over tighten the
screws.
B) Insert 13 wood dowels into assembled unit as shown.
7 A) Insert 6 cams and 2 barrel nuts into assembled
unit as shown. Make sure arrows on each cam point
toward nearest edge with holes. Using a screwdriver,
align hole of each barrel nut with the hole in the nearest
edge.
B) With the assistance of another adult, fit dowels of
assembled unit into corresponding holes of base. With a
screwdriver, turn each cam clockwise until it securely
engages each cam screw.
C) Insert 2 large bolts into barrel nuts of small side panels. Make sure bolts securely engage each barrel nut.
NOTE: Make sure arrows
on each cam point toward
nearest edge with holes
B
Made in China - r13Page 3 of 6
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
PATERSON CORNER MEDIA STAND
Refer to Hinge Adjustment
diagram for adjusting the
alignment of the
door hinges
left door
front
A
A
B
right door
front
pull
left and right
door fronts
8 Attach 2 hinges to left and right door fronts with 2
screws per hinge as shown, using a screwdriver.
B
9 A) With the assistance of another adult, position unit
upright. Attach left and right door fronts to assembled
unit as shown. Secure each hinge with 4 screws.
B) Attach 2 pulls to left and right door fronts as shown.
Secure each pull with 1 pull bolt, using a screwdriver.
shelf pin
11 Place adjustable shelf onto shelf pins. Make sure
shelf is securely supported by each shelf pin.
10 Insert 4 shelf pins at desired shelf heights as shown.
Made in China - r13Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Assembly is now complete.
adjustable
shelf
Page 4 of 6
PATERSON CORNER MEDIA STAND
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the wood is finished with a protective clear lacquer.
HINGE ADJUSTMENT
If the doors do not appear square or aligned,
loosen or tighten the appropriate screws on
each case hinge as illustrated.
1)
Side to side adjustment:
Loosen screw A, adjust gap
with screw B and re-tighten
screw A.A.
2) Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw
A
B
1
A
3) Height adjustment:
Loosen screw C, adjust
door height and retighten screw C.
C
C
2
3
Made in China - r13Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 5 of 6
PATERSON CORNER MEDIA STAND
wall
F
C
plastic
anchor
wall
bracket
strap
D
large
screw
small
A
screw
anti-tip
bracket
OPTIONAL WALL MOUNTING INSTRUCTIONS:
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it
is essential to use wall anchors appropriate to your wall type
(i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach 1 anti-tip bracket to top of unit as shown, using
2 small screws.
B) Determine the final location of unit. Mark position on the
wall, approximately 2" below the anti-tip bracket mounted to
the back of the unit.
C) Drill a pilot hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Gently tap the plastic anchor
until the flange of the anchor is flush with the wall.
D) Attach the wall bracket to the wall by inserting 1 large screw through the wall bracket and into the plastic anchor
in the wall.
E) Place the unit so the anti-tip bracket on the back edge is
aligned with the wall bracket.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure.
Repeat step A-G for remaining wall mounting assembly.
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
Wall mounting assembly is now complete.
Made in China - r13Page 6 of 6
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.