Page 1
PATERSON MEDIA STAND
ASSEMBLY HARDWARE
Thank you for purchasing the Paterson Media Stand.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
4 - pull bolts12 - wood
4 - hinges
6 - large
bolts
Missing hardware?
Please call 800.606.6387
for replacements.
dowels
6 - barrel
nuts
6 - small
bolts
8 - shelf
pins
WALL MOUNTING HARDWARE
1 - wall
strap
1 - wall
bracket
1 - anti-tip
bracket
1 - plastic
anchor
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead power tools)
1 - large
screw
24 - screws
2 - small
screws
1 - top panel
1 - base
2 - side panels
(1 left, 1 right)
1 - partition
Made in China - r12 Page 1 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
2 - doors
(1 left, 1 right)
1 - back panel
2 - adjustable shelves
1 left, 1 right)
(
2 - pulls
Page 2
PATERSON MEDIA STAND
partition
B
right
side
panel
left side
panel
A
A
top panel
1 Insert 6 wood dowels into top panel as shown.
back panel
top panel
2 A) Carefully place top panel onto a clean, padded
surface as shown. Fit dowels of top panel into corresponding holes of left/right side panel and partition. Loosely
secure left/right side panel and partition to top panel with
2 small bolts as shown.
B) Insert 6 wood dowels into left/right side panels and
partition as shown.
B
bottom
panel
A
NOTE: Make sure
hole of barrel nut
aligns with nearest
edge with holes
NOTE: Do not over
tighten the bolts
4 A) Insert 2 barrel nuts into left/right side panels and
partition as shown. Using a phillips head screwdriver,
align hole of each barrel nut with the nearest edge with
holes.
3 Carefully slide back panel into corresponding grooves
of assembled unit as shown. At this point, secure all small
bolts using a phillips head screwdriver. Do not over
tighten the bolts.
Made in China - r12 Page 2 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
B) With the assistance of another adult, fit dowels of
assembled unit into corresponding holes of bottom panel.
Secure bottom panel with 6 large bolts as shown. Make
sure bolts securely engage each barrel nut.
Page 3
PATERSON MEDIA STAND
Refer to Hinge Adjustment
diagram for adjusting the
alignment of the
door hinges
A
A
B
right door
front
left and right
door fronts
5 Attach 2 hinges to left and right door fronts with 2
screws per hinge as shown.
shelf pin
left door
front
B
pull
6 A) With the assistance of another adult, position unit
upright. Attach left and right door fronts to assembled
unit as shown. Secure each hinge with 4 screws.
B) Attach 2 pulls to left and right door fronts as shown.
Secure each pull with 2 pull bolts.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the wood is finished with a protective clear lacquer.
right
adjustable
shelf
left
adjustable
shelf
7 A) Insert 8 shelf pins at desired shelf heights as
shown.
B) Place 2 left and right adjustable shelves onto shelf
pins. Make sure shelves are securely supported by each
shelf pin.
Assembly is now complete.
Made in China - r12 Page 3 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 4
PATERSON MEDIA STAND
HINGE ADJUSTMENT
If the doors do not appear square or aligned,
loosen or tighten the appropriate screws on
each case hinge as illustrated.
1)
Side to side adjustment:
Loosen screw A, adjust gap
with screw B and re-tighten
screw A.
A
B
1
2) Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw
A.
A
2
3) Height adjustment:
Loosen screw C, adjust
door height and retighten screw C.
C
C
3
Made in China - r12 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 4 of 5
Page 5
PATERSON MEDIA STAND
wall
F
C
plastic
anchor
wall
bracket
strap
D
large
screw
small
A
screw
anti-tip
bracket
OPTIONAL WALL MOUNTING INSTRUCTIONS:
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it
is essential to use wall anchors appropriate to your wall type
(i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach 1 anti-tip bracket to top of unit as shown, using
2 small screws.
B) Determine the final location of unit. Mark position on the
wall, approximately 2" below the anti-tip bracket mounted to
the back of the unit.
C) Drill a pilot hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Gently tap the plastic anchor
until the flange of the anchor is flush with the wall.
D) Attach the wall bracket to the wall by inserting 1 large
screw through the wall bracket and into the plastic anchor
in the wall.
E) Place the unit so the anti-tip bracket on the back edge is
aligned with the wall bracket.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure.
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
Wall mounting assembly is now complete.
Made in China - r12 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 5 of 5
Loading...