
PARKER SPIRITS CABINET
HARDWARE
Thank you for purchasing the Parker Spirits Cabinet.
This page
Please take the time to identify the hardware as well as
the individual components
unpack and prepare for assembly, place the contents
on a carpeted or padded area to protect them from
damage.
Note: 2 people are required to safely assemble this
product.
lists all the contents included in the box.
to this product. As you
COMPONENTS
12 - large
bolts
4 - small
bolts
Missing hardware?
Please call 800.606.6387 for replacements.
16 - spring
washers
4 - large
screws
16 - flat
washers
6 - small
screws
TOOLS REQUIRED
phillips head screwdriver
We recommend the use of hand tools instead of power tools.
allen wrench (included)
4 - legs
1 - bottom
back panel
2 - top panels 2 - horizontal
Made in China - r05 Page 1 of 4
1 - bottom frame
1 - middle panel 1 - top
1 - drawer assembly
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
5 - vertical
wine racks
1 - left
frame
back panel
1 - right
frame
1 - hinged
panel
2 - pulls
wine racks

PARKER SPIRITS CABINET
NOTE: Do not over
tighten the bolts
1 Attach 4 legs to bottom frame with 2 large bolts, 2
spring washers and 2 flat washers per leg. Secure, but
do not over tighten, bolts with an allen wrench.
NOTE: During assembly,
make sure grooves of left
and right frames are facing
each other as shown.
2 With the assistance of another adult, fit pre-assembled
dowels of right frame into corresponding holes of bottom
frame as shown. Secure right frame with 2 large bolts,
2 spring washers and 2 flat washers.
Repeat step 2 for left frame.
B
A
3 A) Insert bottom back panel into corresponding
grooves of left/right frames as shown.
B) Place middle panel onto pre-assembled shelf pins
as shown. Make sure shelf is securely supported by
each shelf pin.
Made in China - r05 Page 2 of 4Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
4 Fit top back panel into corresponding grooves of
assemblyas shown.

PARKER SPIRITS CABINET
A
B
5 Place hinged panel onto pre-assembled shelf pins
as shown, and secure with 4 large screws.
NOTE: Make sure
top panels are
aligned. Adjust
levelers as
necessary.
levelers
6 A) Open hinged panel as shown, and secure preassembled arm hinge with 2 small screws.
B) Attached 1 pull to hinged panel with 2 small screws.
7 Attach 2 top panels to assembly with 2 small bolts,
2 spring washers and 2 flat washers per panel as shown.
Do not fully tighten the bolts. Make sure top panels are
orientated as shown. If the top panels are not aligned,
make sure assembly is level and adjust levelers as
necessary. At this point, secure but do not over tighten
the bolts.
Made in China - r05 Page 3 of 4Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
8 Fit slots of 5 vertical wine racks into corresponding
slots of 2 horizontal wine racks as shown.

PARKER SPIRITS CABINET
9 Insert wine rack assembly into cabinet assembly
as shown.
10 Attach 1 pull to drawer assembly with 2 small screws
as shown.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not
use abrasive cleaners. Do not use furniture wax or
polish as the wood is finished with a protective clear
lacquer. It is recommended to use coasters to protect
against heat and water.
11 Fit drawer glides of drawer into corresponding glides
of assembly. Make sure drawer assembly is securely
supported by glides.
Assembly is now complete.
Made in China - r05 Page 4 of 4Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com