Craftsman Workbench Frame - Red Owner's Manual
OPERATOR’S MANUAL
Workbench 6' & 8'
Please indicate the following information from the service part drawing provided.
Model Number: ____________________________
Model Description: _________________________
*Product you purchased may vary from picture shown.
Caution: Read and follow all Safety Rules and Operating Instructions before first
use of this product. Retain this document for future reference.
Distributed by Sears Brands Management Corporation., Hoffman Estates, IL 60179
F1725
SAFETY
SAFETY WARNINGS AND CAUTIONS:
• Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or product
damage.
• Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or product
damage.
• DO NOT stand on this product. You may fall which m ay cause personal injury.
• DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage.
• Appropriately secure this product before moving it with a forklift.
• DO NOT alter this product in any m anner. For example, do not weld external lockbars or attach electrical equipm ent. This
may cause product dam age or personal injury.
• Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an un-level surface,
which may cause personal injury or product damage.
• DO NOT step in the drawers. You may fall which may cause personal injury.
• Maximum combined weight limit not to exceed 1,450 pounds. If the limit is exceeded, the product could collapse and cause
personal injury or product damage.
Tools Required:
Socket wrench
3" socket extension
7/16" Deep-well Socket
3/8" Wrench
Drill
1/8" Drill bit
Square
Tape measure
Hardware Included
AA(30)
BB(30)
CC(30)
DD(15)
E
(Purchased
Separately)
D
C
B (3)
A (2)
EE(4)
Note: Not all hardware is used for
the 6' workbench.
Call 1-800-4MY-HOME (1-800-469-4663) for Service Parts.
Refer to Service Parts Drawing for full listing of Service Parts.
2
ASSEMBLY
STEP (3):
STEP (1):
EE(4)
• Assemble (2) (EE) in each (A). Some adjustments may be
necessary after workbench is in desired position.
A
EE
AA(8)
BB(8)
CC(8)
• Place workbench top (Purchased Separately), (D) with top side
down. (Use packaging material to prevent scratches.
Note: The rail (B) with the label should be placed toward the front
of the unit with the label upside down.
• Assemble (2) (A) and (2) (B), as shown, using (8) (AA), (8)
(BB), and (8) (CC). Flanges of (B) should point in. Notches
should be up.
• Finger tighten.
(EE)
on top
A
Notches
on top
Front
CC
BB
AA
STEP (2):
For 6' Workbench skip this step
AA(16) BB(16) CC(16)
• Assemble (1) (B) and (1) (D), as shown, using (8) (AA), (8)
(BB), and (8) (CC).
• Repeat for other top support rail.
• Finger tighten.
AA
BB
CC
Flanges
point in
Back
B
STEP (4):
AA(6)
BB(6)
• Attach remaining (B) in top back set of holes in (2) (A) as
shown, using (4) (AA), (4) (BB), and (4) (CC). Flanges of (B)
should point out.
• Attach remaining hardware in bottom holes in top front set of
holes as shown in illustration.
• Finger tighten.
CC(6)
B
D
3
Loading...