Craftsman STAINLESS STEEL CHEST CABINET Owner's Manual

OPERATOR’S MANUAL

R

STAINLESS STEEL CHEST & CABINET

PRODUCT PURCHASED MAY VARY FROM

PICTURE SHOWN.

SERVICE PARTS

CALL 1-800-366-7278 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listing of Service Parts.

LOCATING MODEL # INFORMATION

Model numbers and other information required for service parts is
located on a label on the interior right side of the top most drawer.

CAPACITIES

• The maximum weight for each drawer should be no more than
100 lbs.

• The maximum product weight, including contents, should be no
more than 1200 pounds for rolling cabinet.

MAINTENANCE

• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit’s luster nish. Apply the wax as to
a car. The wax will also help protect the unit against scratches.

• Grease and oil can be removed with most standard cleaning
uids. For safety, use a nonammable cleaning uid.

• If drawer liners are supplied, it is recommended they are used
to protect the nish inside the drawers and to make the drawers
easier to clean. The drawer liners may be cleaned with soap and
water.

• This unit has a clearcoat nish. Do not use stainless steel polish
on this unit.

SAFETY

DANGER is used to indicate a hazardous situation which,

if not avoided, will result in serious injury or death.
WARNING indicates a hazardous situation which, if not
avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation which, if not
avoided, may result in minor injury, moderate injury, or property
damage.

CAUTION: Read and follow all Safety Rules and Operating
Instructions before rst use of this product.

DANGER

• DO NOT stand on this product. You may fall or cause product to
tip.

• DO NOT open more than one drawer. The product may become
unstable and tip.

• DO NOT step in the drawers. You may fall or cause product to
tip.

• DO NOT mount this product on a truck bed or any other moving
object.

• DO NOT move the product prior to closing and locking all the
drawers. The drawers could come open and make the product
unstable and tip.

WARNING

• WEAR SAFETY GLASSES when removing or repositioning the
slides.

• When moving this product, push it, do not pull it.

• USE THE BRAKES when not moving this product. This will
prevent the product from rolling.

• DO NOT alter this product in any manner. For example, do not
weld external lockbars or attach electrical equipment.

• Keep the product on level surfaces. The product may become
unstable and tip if stored or moved on an uneven surface.

• BE CAREFUL when closing the cover. Remove hands before
the cover closes completely.

• For casters, use high quality bearing grease, (yearly).

• Lubricate the slides with grease or equivalent,(twice yearly.

• Lubricate lock with graphite, (yearly).

Ball-bearing Slides

Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179

CAUTION

• This product is not designed to be directly lifted with a fork lift, or
to be towed with any mechanical devices.

• The maximum weight for each drawer should never be exceeded.

• Only transport this product empty. Properly secure when trans­porting.

• DO NOT exceed maximum product weight, including contents.
See Operations Sections: Capacities for more information.

F1940

HARDWARE ASSEMBLY

Tools Required:

5/16 UNC wrench
Cross-tip Screwdriver

Hardware Included:

10-24 UNC Pan Head
Screw (Qty: 8)

5/16-18 UNC Hex Screw
(Qty: 16)

Mounting Bracket (Qty: 2)

CASTER INSTALLATION

Items Needed:

5/16 - 18 UNC screws (16)

· Place the unit on it’s top. Use the packaging material to

protect the nish.

· Attach casters using (4) 5/16 - 18 UNC screws in each

caster. Mount both swivel casters on the same side of the
cart as the side handle.

· Wrench tighten all screws. Do not overtighten. Return the

unit to its upright position.

MOUNTING CHEST ON CART
Items Needed:

10-24 UNC Pan Head screws (8)
Mounting Brackets (2)

2

REMOVING AND INSTALLING DRAWERS

· Empty the drawer.

· Fully extend the drawer.

INSTALLING DRAWERS

Ball bearing slide - Pull slides and slide carrier out to fully
extended position (see illustration.) Hold the slide on the
cabinet while aligning it with the slide on drawer. Slightly
insert one side and repeat for the other side. Slowly push
drawer to its fully closed position to engage slide. Open
drawer and reclose to ensure proper operation.

slide carrier

Lever Style - Lift or lower, depending on the slide, the
release lever on both sides, (this allows the slides to ride
over the stops.) Pull out to remove.

Tab Style - Depress the release tabs on both sides,
(this allows the slides to ride over the stops.)
Pull out to remove.

slide

3