Craftsman Premium Heavy-Duty Hanging Wall Cabinet User Manual
OPERATOR’S MANUAL
WALL CABINET
MAINTENANCE
• Lubricate lock with graphite, (yearly).
• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.
• Auto wax will preserve the unit’s luster nish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.
• Grease and oil can be removed with most standard
cleaning uids. For safety, use a nonammable cleaning uid.
SAFETY
DANGER is used to indicate a hazardous situation which,
if not avoided, will result in serious injury or death.
WARNING indicates a hazardous situation which,
if not avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation which, if not
avoided, may result in minor injury, moderate injury, or property
damage.
CAUTION: Read and follow all Safety Rules and Operating
Instructions before rst use of this product.
DANGER
• DO NOT stand on this product. You may fall or cause product
to tip.
• DO NOT mount this product on a truck bed or any other moving
object. This may cause personal injury or product damage.
• DO NOT step on the shelves. You may fall or cause product to
tip.
SERVICE PARTS
CALL 1-800-469-4663 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listing of Service Parts.
LOCATING MODEL # INFORMATION
Model numbers and other information required for service parts is
located on a label on the interior right side.
CAPACITIES
• The maximum weight for each shelf in a door should be no more
than 7 lbs.
• The maximum weight for each full shelf in cabinet should be no
more than 50 lbs.
• The maximum product weight, including contents, should be no
more than 180 lbs when mounted to trackwall.
• The maximum product weight, including contents, should be no
more than 200 lbs when mounted directly to wall studs.
WARNING
• Use appropriate safety equipment when using power
and hand tools. Failure to do so may cause personal
injury or product damage.
• Use adequate manpower when assembling and moving
this unit. Failure to do so may cause personal injury or
product damage.
• DO NOT alter this product in any manner. For example, do not
weld external lockbars or attach electrical equipment.
• Keep the product on level surfaces. The product may become
unstable and tip if stored or moved on an uneven surface.
• Cabinet MUST be attached to a stud in a wood frame wall.
Failure to do so may cause personal injury or product damage
• When not using the supplied bracket to hang the wall cabinet, be
sure to secure wall cabinet to a studded or concrete wall. Failure
to do so may cause the wall cabinet to fall. This may cause
personal injury or product damage.
• When using the supplied bracket to hang wall cabinet, be sure
the bracket is level. Failure to do so may cause the wall cabinet
to fall. This may cause personal injury or product damage.
CAUTION
• Appropriately secure this product before moving it with
a forklift.
• Only transport this product empty. Properly secure when
transporting.
Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179
F1998
HARDWARE
TOOLS REQUIRED:
ASSEMBLY
Mounting Option 1
Socket Wrench
3/8" Socket
7/16" Socket
3" Socket Extension
Drill
1/8" Drill Bit
5/32” Hex Key
HARDWARE INCLUDED:
1/4-20 x 3/4" Button Head Screw
(Qty: 4)
1/4-20 Serrated Flange Nut (Qty: 4)
Snap Grommet (Qty: 1)
Mounting Bracket (Qty: 1)
Items Needed:
1/4-20 x 3/4" Button Head Screw (Qty: 4)
1/4-20 Serrated Flange Nut (Qty: 4)
Mounting Bracket (Qty: 1)
Process:
Note: Option 1 is for hanging cabinet on trackwall. If hang-
ing cabinet directly on wall, go to option 2.
• Attach Top and Mounting Bracket, as shown
using, (4) 1/4-20 x 3/4" Button Head Screws, and
(4) 1/4-20 Serrated Flange Nuts.
• Finger tighten.
Mounting Bracket
Top
Spacer Block (Qty: 1)
2
• Hook bracket over trackwall and slide down
into place.
Note: Foam pad spacer block should be located as
close to the center of the cabinet as possible above
the bottom edge in back of the cabinet.
• Peel paper backing from spacer, attach to the
back of the cabinet near the bottom to hold cabinet
level.
Hook over Trackwall and
slide down into place.
Items Needed:
Grommet (Qty: 1)
Process:
• Place the Grommet in the hole.
Grommet
Foam Pad
Mounting Option 2
Process:
• Align Wall Cabinet with studs.
• Mark and drill (2) 1/8" pilot holes.
Note: Use outside holes for mounting to studs on 24"
centers. Use inside set of holes for mounting to studs
on 16" centers.
• Attach Wall Cabinet to studs using appropriate
hardware as dened by your local building code.
16" centers
24"
centers
3
Loading...