Craftsman 917.272850 User Manual

Download

Page 1

Owner’s Manual

LAWN TRACTOR

22.0 HP, 42” Mower Electric Start

6 Speed Transaxle

Model No.

917.272850

This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner’s Manual.

IMPORTANT:

Read and follow all Safety Rules and Instructions before operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website:www.sears.com/craftsman

For answers to your questions

about this product, Call:

1-800-659-5917

Sears Craftsman Help Line

5 am - 5 pm, Mors - Sat

........................

Page 2

Warranty......................................

Safety Rules..............................

Product Specifications............... .............6

Assembly/Pre-Operation Operation

Maintenance Schedule..............

....................................

.............

............

.............3

............

..........

...........17

Maintenance

Service and Adjustments....

Storage...............................

Troubleshooting

Repair Parts.........................

Sears Service.....................

........................

...................

..................

..................27

..................

....Back Cover

■mmEm&M:.

LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT For two (2) years from the date of purchase, if this Craftsman Riding Equipment is maintained, lubricated and tuned up according to the instructions in the owner’s manual. Sears will repair or replace free of charge any parts that are found to be defective in

materia! or workmanship according to the guidelines of coverage listed below. Sears will also provide free labor for these applicable warranted parts for the two full years. During the first 30 days of purchase, there will be no charges to service the product at your home for issues covered by this warranty. (See exclusions below). For your conve nience, IN HOME warranty service will still be available after the first 30 days of pur chase, but a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears location. For the nearest authorized Sears location, please call 1-800-4-MY-HOME®. This warranty applies only while this product is within the United States.

This Warranty does not cover:

• Expendable items which become worn during norma! use, including but not limited to blades, spark plugs, air cleaners, belts, and oil filters.

• Standard Maintenance Servicing, oil changes, or tune-ups

• Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass.

• Repairs necessary because of operator abuse, including but not limited to, damage caused by towing objects beyond the capability of the riding equipment, impacting objects that bend the frame or crankshaft, or over-speeding the engine.

• Repairs necessary because of operator negligence, including but not limited to, elec trical and mechanical damage caused by improper storage, failure to use the proper grade and amount of engine oil, failure to keep the deck clear of flammable debris, or failure to maintain the equipment according to the instructions contained in the owner’s manual.

• Engine (fuel system) cleaning or repairs caused by fuel determined to be contami nated or oxidized (stale). In general, fuel should be used within 30 days of its pur chase date.

• Normal deterioration and wear of the exterior finishes, or product label replacement.

• Riding equipment used for commercial or rental purposes.

17 21

28 32

LIMITED WARRANTY ON BATTERY

For ninety (90) days from date of purchase, if any battery included with this riding equip ment proves defective in material or workmanship and our testing determines the battery will not hold a charge. Sears will replace the battery at no charge. During the first 30 days of purchase, there will be no charges to replace the battery at your HOME. After the first 30 days, for your convenience, IN-HOME warranty service will still be avail able but a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears location. For the nearest authorized Sears location, please call 1-800-4-MY-HOME®.

This battery warranty applies only while this product is within the United States. This warranty gives you specific legal rights, and you may also have other rights, which

vary, from state to state. Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL 60179

Page 3

IMPORTANT: This cutting machine is capable of amputating hands and feet and throw ing objects. Failure to observe the following safety instructions could result in serious injury or death.

AwaRNING: In order to prevent ac

cidental starting when setting up, trans

porting, adjusting or making repairs,

always disconnect spark plug wire and

place wire where it cannot contact spark plug.

AwARNING: Do not coast down a hill in

neutral, you may lose control of the tractor. AwaRNING: Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can

lose traction with the ground and cause you to lose control of your tractor. AwaRNING: Engine exhaust, some of its constituents, and certain vehicle compo

nents contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm. AwaRNING: Battery posts, terminals and related accessories contain lead and

lead compounds, chemicals known to the

State of California to cause cancer and

birth defects or other reproductive harm.

Wash hands after handling.

Be aware of the mower discharge direc tion and do not point it at anyone. Do not operate the mower without either the entire grass catcher or the guard in place. Slow down before turning.

Never leave a running machine unat tended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting. Turn off blades when not mowing. Stop engine before removing grass catcher or unclogging chute. Mow only in daylight or good artificial light.

Do not operate the machine while under the influence of alcohol or drugs. Watch for traffic when operating near or crossing roadways.

Use extra care when loading or un loading the machine into a trailer or truck.

Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related in juries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.

I. GENERAL OPERATION

• Read, understand, and follow all instruc tions in the manual and on the machine before starting.

• Only allow responsible adults, who are familiar with the instructions, to operate the machine.

• Clear the area of objects such as rocks, toys, wire, etc., which could be picked

• Keep machine free of grass , leaves or other debris build-up which can touch hot exhaust / engine parts and burn . Do not allow the mower deck to plow leaves or other debris which can cause build up to occur. Clean any oil or fuel spillage before operating or storing the machine . Allow machine to cool before storage.

up and thrown by the blade.

• Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso

lutely necessary. Always look down and

behind before and while backing.

II slope operation

Slopes are a major factor related to lossof-control and tipover accidents, which can

result in severe injury or death. All slopes

require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.

Page 4

DO:

• Mow up and down slopes, not across.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Un even terrain could overturn the machine.

Tall grass can hide obstacles.

• Use slow speed. Choose a low gear

so that you will not have to stop or shift while on the slope.

• Follow the manufacturer’s recommend ations for wheel weights or counter weights to improve stability.

• Use extra care with grass catchers or other attachments. These can change the stability of the machine.

• Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction.

• Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope.

DO NOT:

• Do not turn on slopes unless neces sary, and then, turn slowly and gradually downhill, if possible.

• Do not mow near drop-offs, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in.

• Do not mow on wet grass. Reduced traction could cause sliding.

• Do not try to stabilize the machine by putting your foot on the ground.

• Do not use grass catcher on steep slopes.

III. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the ma chine and the mowing activity. Never as sume that children will remain where you last saw them.

• Keep children out of the mowing area and under the watchful care of another responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and when backing, look behind and down for small children.

• Never carry children. They may fall off and be seriously injured or interfere with safe machine operation.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

IV. SERVICE

• Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive.

- Use only an approved container.

- Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. Do not smoke.

- Never refuel the machine indoors.

- Never store the machine or fuel con

tainer inside where there is an open flame, such as a water heater.

• Never run a machine inside a closed area.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep equip ment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to cool before storing.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

• Never make adjustments or repairs with the engine running.

• Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer's recommended parts, when necessary.

• Mower blades are sharp and can cut. Wrap the biade(s) or wear gloves, and

use extra caution when servicing them.

• Check brake operation frequently. Ad just and service as required.

Page 5

Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area.

Never carry passengers or children even with the blades off.

Do not mow in reverse unless abso

lutely necessary. Always look down and behind before and while backing.

Never carry children. They may fall off and be seriously injured or interfere with safe machine operation.

Keep children out of the mowing area and under the watchful care of another

responsible adult.

Be alert and turn machine off if children enter the area.

Before and when backing, look behind and down for small children.

Mow up and down slopes {15° Max), not across.

Remove obstacles such as rocks, tree limbs, etc. Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope.

if machine stops while going uphill, disengage blades, shift into reverse and back down slowly.

Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.

Page 6

PRODUCT SPECIFICATIONS

Gasoline Capacity and Type:

Oil Type (APl-SF-SJ):

Oil Capacity:

Spark Plug: (Gap: .040")

Ground Speed (MPH);

Tire Pressure: Front; 14PSI

Charging System:

Battery; Amp/Hr: 35

Blade Bolt Torque: 27-35 Ft. Lbs.

CONGRATULAnONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact a Sears or other qualified service center. We have competent, well-trained technicians and the proper tools to service or repair this tractor.

Please read and retain this manual. The instructions will enable you to assemble and maintain your tractor properly. Always observe the “SAFETY RULES”.

3.5 Unleaded Regular

SAE 30 (above 32°F) SAE 5W-30 (below 32° F)

W/Filter 4.0 Pints W/0 Filter 3.75 Pints

Champion QC12YC

Forward:

1st 1.2 2nd 1.5 3rd 2.4 4th 3.5 5th 4.8 6th 5.3

Reverse: 1.5

Rear; 10PSI

3 Amps Battery 5 Amps Headlights

Min. CCA; 280 Case Size: U1R

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in main taining, caring for and using your tractor.

• Follow the instructions under “Mainte

nance” and “Storage” sections of this

owner’s manual.

^WARNING: This tractor is equipped with an interna! combustion engine and should not be used on or near any unim

proved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state

laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the state of California the above is re quired by law (Section 4442 of the Califor nia Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears service center (See REPAIR PARTS section of this manual).

REPAIR PROTECTION AGREEMENTS

Congratulations on making a smart pur chase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like ali prod ucts, it may require repair from time to time. That’s when having a Repair Protec tion Agreement can save you money and aggravation.

Purchase a Repair Protection Agreement now and protect yourself from unexpected hassie and expense.

Here’s what’s included in the Agreement;

• Expert service by our 12,000 profe sional repair specialists.

• Unlimited service and no charge for parts and labor on all covered repairs.

• Product replacement if your covered product can’t be fixed.

• Discount of 10% from regular price of service and service-related parts not covered by the agreement; also, 10% off regular price of preventive mainte

nance check.

• Fast help by phone - phone support from a Sears technician on products

requiring in-home repair, plus conve

nient repair scheduling. Once you purchase the Agreement, a simple phone cal! is ali that it takes for you to schedule service. You can call anytime day or night, or schedule a service ap pointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That’s the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Repair Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information call 1-800-827-6655.

SEARS INSTALLATION SERVICE

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the U.S.A. call 1-800-4-MY-HOME®

Page 7

Page 8

Your new tractor has been assembied at the factory with the exception of those parts ieft

unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes you need are listed below. (1) 3/4" wrench (1) Pliers (2) 7/16" wrench (1) Utility knife (1) Tire pressure gauge

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

1. Remove all accessible loose parts and

parts boxes from carton.

2. Cut along dotted lines on all four pan els of carton. Remove end panels and lay side panels flat.

3. Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND

BOOT

1. Slide extension shaft onto lower steer ing shaft. Align mounting holes in ex

tension and lower shafts and install 1/4

hex bolt and locknut. Tighten securely.

IMPORTANT: Tighten bolt and nut se

curely to 10-12 ft. lbs torque.

2. Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

3. Position front wheels of the tractor so they are pointing straight forward.

4. Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

5. Position steering wheel so cross bars are horizontal (left to right) and slide

inside boot and onto adapter.

6. Assemble large flat washer, 1/2 hex

nut and tighten securely.

7. Snap steering wheel insert into center of steering wheel.

8. Remove protective materials from trac tor hood and grill.

IMPORTANT: Check for and remove any staples in skid that may puncture tires where tractor is to roll off skid.

HOWTO SET UP YOUR TRACTOR

CHECK BATTERY

1. Lift hood to raised position. NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instruc tions).

Page 9

INSTALL SEAT

Adjust seat before tightening adjustment

knob.

1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

2. Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

3. Place seat on seat pan so head of shoulder bolts are positioned over the

large slotted holes in pan.

4. Push down on seat to engage shoulder bolts in slots and pull seat towards rear of tractor.

5. Pivot seat and pan forward and as semble adjustment knob and flat washer loosely. Do not tighten.

6. Lower seat into operating position and sit in seat.

7. Slide seat until a comfortable position

is reached which allows you to press

clutch/brake pedal all the way down.

8. Get off seat without moving its ad

justed position.

9. Raise seat and tighten adjustment knob securely.

NOTE: You may now roll or drive your tractor off the skid. Foilow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)

1. Press lift lever plunger and raise attachment lift lever to its highest po sition.

2. Release parking brake by depressing clutch/brake pedal.

3. Place gearshift lever in neutral (N) position.

4. Roll tractor forward off skid.

5. Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of controls)

^WARNING: Before starting, read, un

derstand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

1. Be sure all the above assembly steps have been completed.

2. Check engine oil level and fill fuel tank with gasoiine.

3. Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

4. Place gear shift lever in neutral (N) position.

5. Press iift lever plunger and raise attachment iift lever to its highest posi

tion.

6. Start the engine. After engine has started, move throttle control to idle position.

7. Depress clutch/brake pedal into full "BRAKE" position and hold. Move

gearshift lever to 1 st gear.

8. Slowly release clutch/brake pedal and slowly drive tractor off skid.

9. Apply brake to stop tractor, set park ing brake and place gearshift lever in neutral position.

10. Turn ignition key to "STOP" position.

Continue with the instructions that follow.

Page 10

INSTALL MULCHER PLATE

(If previously removed)

1. Raise and hold deflector shield in upright position.

2. Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

3. Hook front latch into hole on front of

mower deck.

4. Hook rear latch into hole on back of

mower deck.

i^CAUTtON; Do not remove deflector shield from mower.

TO CONVERT TO BAGGING OR DISCHARGING

Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.

NOTE: It is not necessary to change blades. The mulcher blades are designed for discharging and bagging also.

CHECK TIR£ PRESSURE

The tires on your tractor were overin flated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

• Reduce tire pressure to PS I shown in

“PRODUCT SPECIFICATIONS” section of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower hous ing should be properly leveled. See “TO

LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replac ing motion and mower blade drive belts in the Service and Adjustments section

of this manual. Verify that the belts are

routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your trac tor, check to see that the brake is properly adjusted. See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual.

^CHECKLIST

Before you operate and enjoy your new tractor, we wish to assure that you receive the best performance and satisfaction from this Quality Product.

Please review the following checklist; / All assembly instructions have been

completed. / No remaining loose parts in carton. / Battery is properly prepared and

charged. {Minimum 1 hour at 6 amps). / Seat is adjusted comfortably and tight

ened securely. / All tires are properly inflated. (For ship

ping purposes, the tires were overin

flated at the factory). / Be sure mower deck is properly leveled

side-to-side/front-to-rear for best cutting

results. (Tires must be properly inflated

for leveling). / Check mower and drive belts. Be sure

they are routed properly around pulleys

and inside all belt keepers. / Check wiring. See that all connections

are still secure and wires are properly

clamped. While learning how to use your tractor, pay extra attention to the following important

items:

/ Engine oil is at proper level. / Fuel tank is filled with fresh, clean, regu

lar unleaded gasoline. / Become familiar with all controls - their

location and function. Operate them

before you start the engine. / Be sure brake system is in safe oper

ating condition.

Page 11

These symbols may appear on your tractor or in literature supplied with the product.

Learn and understand their meaning.

REVERSE

NEUTRAL

EUTR

ENGINE OFF LIGHTS ON ENGINE ON ENGINE START PARKING BRAKE PARKING BRAKE PARKING BRAKE

IGiNE O

)VER TEM

LIGHT

ATTACHMENT ATTACHMENT

CLUTCH ENGAGED CLUTCH DISENGAGED DANGER, KEEP HANDS KEEP AREA CLEAR

(Automatic Models only)

JGMTS

FREE WHEEL

HIGH

IGiNE

L |\|

LOW

CHOKE

¥ a:

AND FEET AWAY

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury. WARNING indicates a hazard which, if not avoided,

could result in death or serious injury. CAUTION indicates a hazard which, if not avoided,

might result in minor or moderate injury.

FAST

{SEE SAFETY RULES SECTION)

SLOW

ONG B

LOCKED UNLOCKED

-OCKE

IGNITION

SLOPE HAZARDS

Failure to follow instructions could result in serious injury or death. The safety alert symbol is used to identify safety inform ation about hazards which can

result in death, serious injury and/or property damage.

CAUTION when used without the alert symbol, indicates a situation that could result in damage

to the tractor and/or engine.

HOT SURFACES indicates a hazard which, if not avoided, could result in death, serious injury and/or property damage.

FIRE indicates a hazard which, if not avoided,

could result in death, serious injury and/or property damage.

Page 12

KNOW YOUR TRACTOR

READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

TRACTOR

Compare the illustrations with your tractor to famiiiarize yourseif with the locations of various controls and adjustments. Save this manual for future reference.

Our tractors conform to the safety standards of the

American National Standards institute.

AMMETER - indicates charging (+) or discharging (-) of battery. ATTACHMENT CLUTCH LEVER - Used to engage the mower blades, or other at tachments mounted to your tractor. ATTACHMENT LIFT LEVER - Used to

raise, lower, and adjust the mower deck or

other attachments mounted to your tractor.

CLUTCH/BRAKE PEDAL - Used for

declutching and braking the tractor and starting the engine.

GEARSHIFT LEVER - Selects the speed

and direction of tractor.

IGNITION SWITCH - Used for starting and

stopping the engine.

LIFT LEVER PLUNGER - Used to release

attachment lift lever when changing its

position. LIGHT SWITCH POSITION - Turns the headlights on and off. PARKING BRAKE LEVER - Locks clutch/ brake pedal into the brake position.

THROTTLE CONTROL - Used for start

ing and controlling engine speed.

CHOKE CONTROL - Used when starting a cold

engine.

Page 13

FORESIGHT IS BETTiR

THANNOSIQm'

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOWTO USE YOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator

presence sensing switch. When engine is running, any attempt by the operator

to leave the seat without first setting the

parking brake will shut off the engine.

1. Depress clutch/brake pedal all the way

down and hold.

2. Pull parking brake lever up and release pressure from clutch/brake pedal.

Pedal should remain in brake position. Make sure parking brake will hold trac

tor secure.

Attachment Clutch Lever “Engaged” Position

Choke Control

Throttle Contro

Clutch/

Brake Pedal,

“Disengaged

Position

STOPPING

MOWER BLADES -

• To stop mower blades, move attachment

clutch lever to “DISENGAGED” position.

GROUND DRIVE -

• To stop ground drive, depress clutch/

brake pedal all the way down.

• Move gearshift lever to neutral (N)

position.

ENGINE -

• Move throttle control to slow position.

NOTE: Failure to move throttle control

to slow position and allowing engine to

idle before stopping may cause engine to

“backfire”.

• Turn ignition key to “STOP” position and

remove key. Always remove key when leaving tractor to prevent unauthorized use.

• Never use choke to stop engine.

Ignition Key

“Disengaged” Position

Parking Brake

“Engaged”

Position

^ Gearshift

‘Brake” Position

IMPORTANT: Leaving the ignition switch in any position other than "STOP" will cause the battery to discharge and go dead.

NOTE: Under certain conditions when

tractor is standing idle with the engine

running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

^CAUTION: Always stop tractor com

pletely, as described above, before leaving the operator's position.

TO USE THROTTLE CONTROL

Always operate engine at full throttle.

• Operating engine at less than full

throttle reduces the battery charging

rate.

• Full throttle offers the best bagging and

mower performance.

TO USE CHOKE CONTROL

Use choke control whenever you are start ing a cold engine. Do not use to start a warm engine.

• To engage choke control, pull knob out.

Slowly push knob in to disengage.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the gearshift lever.

1. Start tractor with clutch/brake pedal de pressed and gearshift lever in neutral (N) position.

2. Move gearshift lever to desired po sition.

3. Slowly release clutch/brake peda! to start movement.

IMPORTANT: Bring tractor to a complete stop before shifting or changing gears.

Failure to do so will shorten the useful life

of your transaxle.

TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever determines the cutting height.

• Grasp lift lever.

• Press plunger with thumb and move

lever to desired position.

Page 14

The cutting height range is approxi mately 1-1/2 to 4". The heights are mea sured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

• The average lawn should be cut to ap proximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

• For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor

on a flat level surface.

Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in this section of manual).

With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in ap propriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

Repeat for opposite side, installing gauge wheel in same adjustment hole.

Gauge Wheel Mounting Bracket

2. Start mower blades by engaging at tachment clutch control.

TO STOP MOWER BLADES disengage attachment clutch control.

^CAUTfON: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

TO OPERATE ON HILLS ^WARNING: Do not drive up or down

hills with slopes greater than 15° and do not drive across any slope. Use the slope

guide at the back of this manual.

Choose the slowest speed before start ing up or down hills. Avoid stopping or changing speed on hills.

If slowing is necessary, move throttle

control lever to slower position.

If stopping is absolutely necessary, push clutch/brake pedal quickly to brake posi tion and engage parking brake. Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement. To restart movement, slowly release parking brake and clutch/brake pedal. Make all turns slowly.

3/8-16

Locknut

3/8 Washer

Gauge Whee

Shoulder Bolt

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

1. Select desired height of cut.

TO TRANSPORT

Raise attachment lift to highest position with attachment lift control. When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate

means of tying hood to tractor (rope, cord, etc.).

Page 15

TOWING CARTS AND OTHER ATTACH

MENTS

Tow only the attachments that are recom

mended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can iose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

1. Check engine oil with tractor on level ground.

2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, re

move and read oil level. If necessary,

add oil until “FULL’ mark on dipstick is

reached. Do not overfill.

• For cold weather operation you should

change oil for easier starting (See the oil viscosity chart in the Maintenance section of this manual).

• To change engine oil, see the Mainte

nance section in this manual.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do

not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of

87 octane. (Use of leaded gasoline will

increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quan tities that can be used within 30 days to assure fuel freshness.

^CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

near an open flame.

IMPORTANT: When operating in temper atures below32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting.

CAUTION; Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separa tion and formation of acids during storage.

Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

1. Sit on seat in operating position, depress clutch/brake pedal and set

parking brake.

2. Place gear shift lever in neutral (N) position.

3. Move attachment clutch to disengaged position.

4. Move throttle control to fast position

5. Pull choke control out for a cold engine start attempt. For a warm engine start

attempt the choke control may not be needed.

NOTE: Before starting, read the warm and

cold starting procedures below.

6. Insert key into ignition and turn key clockwise to start position and release key as soon as engine starts. Do not run starter continuously for more

than fifteen seconds per minute. If the

engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pul! the choke con

trol out and retry. WARM WEATHER STARTING (50° F and above)

7. When engine starts, slowly push choke

control in until the engine begins to run smoothly. If the engine starts to run roughly, pul! the choke control out slightly for a few seconds and then continue to push the control in slowly.

• The attachments and ground drive can

now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

Page 16

COLD WEATHER STARTING (50° F and below)

7. When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the en gine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

• The attachments can be used during

the engine warm-up period and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance (see “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual).

MOWING TIPS

• Mower should be properly leveled for

best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

• The left hand side of mower should be

used for trimming.

• Drive so that clippings are discharged

onto the area that has already been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.

• When mowing large areas, start by

turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished .

• Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

• Always operate engine at full throttle when mowing to assure better mowing

performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain and give best performance of the at tachment being used.

MULCHING MOWING TIPS

IMPORTANT: For best performance, keep mower housing free of built-up grass and

trash. Clean after each use.

• The special mulching blade will recut the grass dippings many times and

reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recut ting action of the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried and the newly cut area will not be exposed to the direct sun.

• For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass blades. For extremely heavy grass, re duce your width of cut on each pass and mow slowly.

SiftNH i’îv }

MAX 1/3

If grass is extremely tall, it should be mowed twice to reduce load and pos sible fire hazard from dried clippings. Make first cut relatively high; the second to the desired height.

Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a sec ond cut, mow across or perpendicular to the first cut path. Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn.

Page 17

Check Brake Operation Check Tire Pressure

Check Operator Presence and interiock Systems

Check for Loose Fasteners

Sharpen/Replac© Mower Blades

Lubrication Chart

Check Battery Level

Clean Battery and Terminais Check Transaxfe Cooling Check V“Belts

Check Engine Oil Level Change Engine Oil (with oil filter) Change Engine Oi! (without oil filter)

Clean Air Filter

Clean Air Screen

inspect Muffier/Spark Arrester

Replace Oi! Filter (If equipped)

Clean Engine Cooling Fins Replace Spark Plug Replace Air Filter Paper Cartridge Replace Fuel Filter

1 - Change more often when operating under a heavy load or

in high ambient temperatures-

2 - Service more often when operating in dirty or dusty conditions

✓ ✓ ✓

✓ ✓

✓

✓ s ✓ ✓

✓ 4

✓ ✓ ✓

✓

1,2

✓ 2

✓ s

✓

3 - Replace blades more often when mowing In sandy soil. 4 “ Not required if equipped with maintenance“ffee battery. 5 " Tighten front axle pivot bolt to 35 ft.“lbs. maximum.

Do not overtighten.

✓ b

✓

✓ 2

✓

✓ ✓

✓

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator

must maintain tractor as instructed in this manual. Some adjustments will need to be made

periodically to properly maintain your tractor. All adjustments in the Service and Adjust

ments section of this manual should be checked at least once each season.

• Once a year you should replace the

spark plug, clean or replace air filter, and check biades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer.

BEFORE EACH USE

Check engine oil level.

Check brake operation. Check tire pressure.

Check operator presence and

interlock systems for proper operation.

Check for loose fasteners.

LUBRICATION CHART

®SAE 30 or 10w30 MOTOR OIL ©GENERAL PURPOSE GREASE ©REFER TO Maintenance “ENGINE” SECTION

IMPORTANT: Do not oil or grease the pivot points which have special nylon bearings. Viscous lubricants will attract dust and dirt that will shorten the life of the self-lubricating bearings. If you feel they must be lubricated, use only a dry, pow dered graphite type lubricant sparingly.

Page 18

TRACTOR

Always observe safety rules when per forming any maintenance.

BRAKE OPERATION If tractor requires more than six (6) feet

stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

• Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

• Keep tires free of gasoline, oil, or insect control chemicals which can harm rub ber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry

rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your trac tor does not function as described, repair the problem immediately.

• The engine should not start unless the

clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

• When the engine is running, any at

tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

• When the engine is running and the

attachment clutch is engaged, any at tempt by the operator to leave the seat should shut off the engine.

• The attachment dutch should never op

erate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

4. Reassemble blade bolt, lock washer and flat washer in exact order as shown.

5. Tighten blade bolt securely (27-35 Ft.

Lbs. torque).

IMPORTANT: Blade bolt is grade 8 heat

treated.

Mandrel Assembly

Trailing ■

Edge Up ^lenter.

Fiat Washer

Lock Washer

^^Blade Bolt (Grade)*

*A Grade 8 heat treated bolt can be identified

by six lines on the bolt head.

TO SHARPEN BLADE

NOTE: We do not recommend sharp

ening blade - but if you do, be sure the

blade is balanced.

Care should be taken to keep the blade

balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine.

• The blade can be sharpened with a file

or on a grinding wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, you will need a

5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with

balancer.) NOTE: Do not use a nail for balancing blade. The lobes of the center hole may

appear to be centered, but are not.

• Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

BLADE REMOVAL

1. Raise mower to highest position to al low access to blades.

2. Remove blade bolt, lock washer and flat washer securing blade.

3. Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How ever, periodic charging of the battery with an automotive charger will extend its life.

• Keep battery and terminals clean. Keep battery bolts tight.

Page 19

• Keep small vent holes open.

• Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on

your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is

not necessary.

TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and

terminals can cause the battery to “leak”

power.

1. Remove terminal guard.

2. Disconnect BLACK battery cable first

then RED battery cable and remove battery from tractor.

3. Rinse the battery with plain water and

dry.

4. Clean terminals and battery cable ends

with wire brush until bright.

5. Coat terminals with grease or petro

leum jelly.

6. Reinstall battery (See “REPLACING

BATTERY" in the SERVICE AND AD

JUSTMENTS section of this manual).

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt

and chaff which can restrict cooling.

Check the crankcase oil level before start ing the engine and after each eight (8) hours of operation. Tighten oil fill cap/ dipstick securely each time you check the

oil level.

TO CHANGE ENGINE OIL

Determine temperature range expected before oil change. All oil must meet API service classification SF-SJ.

• Be sure tractor is on level surface.

• Oil will drain more freely when warm.

• Catch oil in a suitable container.

1. Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

2. Remove yellow cap from end of drain valve and install the drain tube onto the fitting.

Oil Drain Valve

Closed and Locked

Position

V"*BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace

if necessary. The belts are not adjustable. Replace belts if they begin to slip from

wear.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil’s SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in

cold weather, these multi-viscosity oils will

result in increased oil consumption when used above 32°F. Check your engine oil

level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of op eration or at least once a year if the tractor

is not used for 50 hours in one year.

Yellow Cap-

Drain Tube

3. Unlock drain valve by pushing inward slightly and turning counterclockwise.

4. To open, pull out on the drain valve.

5. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin Is in the locked position as shown.

6. Remove the drain tube and replace the cap onto the end of the drain valve.

7. Refill engine with oil through oil fill dip stick tube. Pour slowly Do not overfill. For approximate capacity see “PROD UCT SPECIFICATIONS” section of this manual.

8. Use gauge on oil fill cap/dipstick for checking level. For accurate reading,

tighten dipstick cap securely onto the tube before removing dipstick. Keep oil

at “FULL’ line on dipstick. Tighten cap onto the tube securely when finished.

Page 20

ENGINE OIL FILTER

Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year.

AIR FILTER

Your engine will not run properly using a dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every

100 hours of operation or every season, whichever occurs first. Service air cleaner more often under dusty conditions.

1. Remove knobs and cover.

TO SERVICE PRE-CLEANER

2. Wash it in liquid detergent and water.

3. Squeeze it dry in a clean cloth.

4. Saturate it in engine oil. Wrap it in

clean, absorbent cloth and squeeze to remove excess oil.

NOTE: If very dirty or damaged, replace pre-cleaner.

TO SERVICE CARTRIDGE

1. Clean cartridge by tapping gently on flat surface. If very dirty or damaged, replace cartridge.

2. Reinstall precleaner cartridge, cover and secure with knobs.

IMPORTANT: Petroleum solvents, such as kerosene, are not to be used to clean the cartridge. They may cause deterio

ration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry

cartridge.

Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cool

ing shrouds. Ciean the cooling fins and external surfaces as necessary. Make sure the cooling shrouds are reinstalled.

NOTE: Operating the engine with a

blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds

removed will cause engine damage due to overheating.

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could cre ate a fire hazard and/or damage.

SPARK PLUG(S)

Repiace spark plug(s) at the beginning of each mowing season or after every

100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LiNE FUEL FILTER

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carbu

retor, replacement is required.

1. With engine cool, remove filter and plug fuel line sections.

2. Place new fuel filter in position in fuel line with arrow pointing towards carbu retor.

3. Be sure there are no fuel line leaks and

clamps are properly positioned.

4. Immediately wipe up any spilled gaso line.

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stub born dried gum fibers.

CLEAN AIR INTAKE/COOLING AREAS

To insure proper cooling, make sure the grass screen, cooling fins, and other exter nal surfaces of the engine are kept clean at all times.

Clamp

Fuel Filter

Clamp

CLEANING

• Clean engine, battery seat, finish, etc.

of all foreign matter.

• Keep finished surfaces and wheels free

of all gasoline, oil, etc.

• Protect painted surfaces with auto

motive type wax.

We do not recommend using a garden

hose or pressure washer to clean your

tractor unless the engine and transmis sion are covered to keep water out. Water

in engine or transmission will shorten the useful life of your tractor. Use compressed

air or a leaf blower to remove grass,

leaves and trash from tractor and mower.

Page 21

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY

SERVICE OR ADJUSTMENTS:

1. Depress clutch/brake peda! fully and set parking brake.

2. Place gearshift lever In neutral (N) position.

3. Place attachment clutch in “DISENGAGED” position.

4. Turn ignition key to “STOP” and remove key.

5. Make sure the blades and all moving parts have completely stopped.

6. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER

Mower will be easier to remove from the right side of tractor.

1. Place attachment clutch in “DISEN GAGED” position.

2. Move attachment lift lever forward to lower mower to its lowest position.

3. Roll belt off engine pulley.

4. Remove small retainer spring, and remove clutch spring off pulley bolt.

5. Remove large retainer spring, slide

collar off and push housing guide out of bracket.

6. Disconnect anti-sway bar from chassis

bracket by removing retainer spring.

7. Disconnect suspension arms from rear

deck brackets by removing retainer springs.

8. Disconnect front links from deck by removing retainer springs.

9. Raise lift lever to raise suspension arms. Slide mower out from under trac tor.

Small Retainer Spring

IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links and hook the clutch spring Into square hole in frame.

TO INSTALL MOWER

1. Raise attachment lift lever to its highest position.

2. Slide mower under tractor with deflec tor shield to right side of tractor.

3. Lower lift lever to its lowest position.

4. Connect front links to mower deck and

secure with retainer springs.

5. Connect suspension arms to rear

deck brackets and secure with retainer springs.

6. Connect anti-sway bar to chassis

bracket and secure with retainer spring.

7. Push clutch cable housing guide into

bracket, slide collar onto guide and secure with large retainer spring.

8. Place flat washer and clutch spring on

idler pulley bolt and secure with small retainer spring.

9. Install belt onto engine pulley.

Fiat Washer

Anti-Sway

Bar

Collar

Housing' Guide

Retainer Spring

Clutch Spring

Small Retainer

Clutch

Large Retainer „ , Spring Bracket

Square Hole

Engine PuHey

Retainer Springs (Both Sides)

Deflector Shield

Page 22

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD

UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated,

you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

• Raise mower to its highest position.

• At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both

sides of mower should be the same or within 1/4" of each other.

• If adjustment is necessary, make adjust ment on one side of mower only.

• To raise one side of mower, tighten lift link adjustment nut on that side.

• To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE; Each full turn of adjustment nut

will change mower height about 1/8".

• Recheck measurements after adjusting.

To lower front of mower loosen nut “E” on both front links an equal number of turns. When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links. To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal num ber of turns. The two front links must

remain equal in length. When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

Recheck side-to-side adjustment.

Mandrel

Both Front Links Should be Equal in Length

Bottom edge of mower to ground

/Ground Line \7 /T^

Lift Link Adjustment Nut

Bottom edge of

mower to ground

Suspension Arm

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to side. If the following fronMo-back adjust

ment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side. To obtain the best cutting results, the

mower housing should be adjusted so that the front is approximately 1/8" to 1/2“

lower than the rear when the mower is in

its highest position. Check adjustment on right side of tractor.

Measure distance “D” directly in front and

behind the mandrel at bottom edge of

mower housing as shown.

• Before making any necessary adjust

ments, check that both front links are

equal in length.

• If links are not equal in length, adjust

one link to same length as other link.

TO REPLACE MOWER BLADE DRIVE

BELT

The mower blade drive belt may be re

placed without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1. Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

2. Work belt off both mandrel pulleys and idler pulleys.

3. Pull belt away from mower.

BELT INSTALLATION -

1. Work belt around both mandrel pulleys and idler pulleys

2. Make sure belt is in all pulley grooves and inside all belt guides.

3. Install mower (See “To Install Mower” in this section of this manual).

Page 23

Mandrel Pulley

With parking brake “Engaged”

Mandrel Pulley

TO CHECK AND ADJUST BRAKE

Your tractor is equipped with an adjustable

brake system which is mounted on the right side of the transaxie. If tractor requires more than five {5} feet to

stop at highest speed in highest gear on a

level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

1. Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake.

2. Place gear shift lever in neutral (N) position.

The rear wheels must lock and skid when you try to manually push the tractor for ward. If the rear wheels rotate, the brake

needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

1. Depress clutch/brake pedal all the way down and engage parking brake.

2. Measure distance between brake oper ating arm and nut “A” on brake rod.

3. If distance is other than 1-1/2", loosen

jam nut and turn nut “A” until distance

becomes 1-1/2". Retighten jam nut against nut “A”.

4. Road test tractor for proper stopping distance as stated above. Readjust

if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is neces sary. Replace brake pads or contact a Sears or other qualified service center.

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1. Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt

and position of all belt guides and keepers.

2. Remove belt from stationary idler and clutching idler.

3. Remove belt downward from around engine pulley.

4. Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keepers.

5. Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

Carefully work new belt down between

transaxie belt keepers and onto the

input pulley.

Slide belt into the center span keeper.

Pull belt toward front of tractor and roll around the top groove of engine pulley.

Install belt through stationary idler and clutching idler. Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this section of manual).

Page 24

TRAL ADJUSTMENT

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

1. Make sure transaxle is in neutral (N). NOTE: When the tractor rear wheels move

freely, the transaxle is in neutral.

2. Loosen adjustment bolt in front of the right rear wheel. Position the gear shift lever in the neu

3. tral (N) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

Gearshift Lever

Neutral Lock Gate

Adjustment Bolt

TO ADJUST STEERING WHEEL ALIGN

MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer ing wheel and reassemble with crossbars horizontal. Tighten securely. FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not

adjustable on your tractor. If damage has

occurred to affect the front wheel toe-in or

camber, contact a Sears or other qualified

service center.

TO REMOVE WHEEL FOR REPAIRS

1. Block up axle securely.

2. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not

lose).

3. Repair tire and reassemble.

NOTE: On rear wheels only; align grooves in rear wheel hub and axle. Insert square key.

4. Replace washers and snap retaining

ring securely in axle groove.

5. Replace axle cover.

NOTE: To sea! tire punctures and prevent flat tires due to slow leaks, purchase and

use tire sealant from Sears. Tire sealant also prevents tire dry rot and corrosion.

Washers

Retaining Ring

Axle Cover

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BAT TERY

^WARNING: Lead-acid batteries gen

erate explosive gases. Keep sparks, flame and smoking materials away from bat teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure;

IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle

must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1. Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2. Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3. Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

Page 25

TO REMOVE CABLES, REVERSE ORDER -

1. BLACK cable first from chassis and then from the fully charged battery.

2. RED cable last from both batteries.

®cT'

* ^ no

Weak or Dead Battery

REPLACING BATTERY

WARNING: Do not short battery

terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery,

remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1. Lift hood to raised position.

2. Remove terminal guard.

3. Disconnect BLACK battery cable

then RED battery cable and carefully

remove battery from tractor.

4. Install new battery with terminals in

same position as old battery.

5. Reinstall terminal guard.

6. First connect RED battery cable to

positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

7. Connect BLACK grounding cable to

negative (-) battery terminal with re maining hex bolt and keps nut. Tighten

securely

8. Close terminal access doors.

9. Close hood.

Fully Charged Battery

TO REPLACE HEADLIGHT BULB

1. Raise hood.

2. Pull bulb holder out of the hole in the backside of the grill.

3. Replace bulb in holder and push bulb holder securely back into the hole in

the backside of the grill.

4. Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

• Check wiring. See electrical wiring

diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS SEMBLY

1. Raise hood.

2. Unsnap headlight wire connector.

3. Stand in front of tractor. Grasp hood at

sides, tilt toward engine and lift off of

tractor.

4. When replacing hood, be sure to re

connect the headlight wire connector.

Hex Bolt

Page 26

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex pense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec essary. Check adjustment as described below before loosening cable. If adjust ment is necessary, proceed as follows:

1. With engine not running, move throttle control lever to fast position.

2. Check that swivel is against stop. If it is not, loosen cable clamp screw and pull cable back until swivel is against stop. Tighten cable clamp screw securely.

TO ADJUST CHOKE CONTROL The choke control has been preset at the

factory and adjustment should not be nec essary. Check adjustment as described below before loosening cable. If adjust ment is necessary, proceed as follows:

1. With engine not running, move choke control (located on dash panel) to full choke position.

2. Loosen knob and remove cover as sembly from air cleaner.

3. Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely.

4. Replace air cleaner cover assembly and tighten knob.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for

repair and/or adjustment. High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeed

ing the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed

needs adjusting, contact a Sears or other qualified service center,, which has proper equipment and experience to make any

necessary adjustments.

Page 27

Immediately prepare your tractor for stor age at the end of the season or if the trac tor will not be used for 30 days or more. ^WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a

period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1. Clean entire tractor (See “CLEANING” in the Maintenance section of this manual).

2. Inspect and replace belts, if necessary (See belt replacement instructions in

the Service and Adjustments section of this manual).

3. Lubricate as shown in the Maintenance

section of this manual.

4. Be sure that all nuts, bolts and screws

are securely fastened. Inspect moving parts for damage, breakage and wear.

Replace if necessary.

5. Touch up all rusted or chipped paint

surfaces; sand lightly before painting.

BATTERY

• Fully charge the battery for storage.

• After a period of time in storage, battery

may require recharging.

• To help prevent corrosion and power

leakage during long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Maintenance section of this manual).

• After cleaning, leave cables discon nected and place cables where they

cannot come in contact with battery terminals.

• If battery is removed from tractor for

storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM IMPORTANT; It is important to prevent

gum deposits from forming in essential fuel system parts such as carburetor, fuel

hose, or tank during storage. Also, alcohol

blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can dam age the fuel system of an engine while in storage.

1. Drain the fuel tank.

2. Start the engine and let it run until the fuel lines and carburetor are empty.

• Never use engine or carburetor cleaner

products in the fuel tank or permanent damage may occur.

• Use fresh fuel next season.

NOTE; Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or stor age container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the car buretor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

1. Remove spark plug(s).

2. Pour one ounce of oil through spark

plug hole(s) into cylinder(s).

3. Turn ignition key to start position for a

few seconds to distribute oil.

4. Replace with new spark plug(s).

OTHER

• Do not store gasoline from one season

to another.

• Replace your gasoline can if your can

starts to rust. Rust and/or dirt in your gasoline will cause problems.

• If possible, store your tractor indoors

and cover it to give protection from dust and dirt.

• Cover your tractor with a suitable pro

tective cover that does not retain mois ture. Do not use plastic. Plastic cannot

breathe which allows condensation to

form and will cause your tractor to rust. IMPORTANT: Never cover tractor while engine and exhaust areas are still warm.

Page 28

TROUBLESHOOTING CHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION

Will not start

Hard to start

1. Out of fuel.

2. Engine not “CHOKED” 2. See “TO START ENGINE” properly. in Operation section.

3. Engine flooded. 3. Wait several minutes

4. Bad spark plug. 4. Replace spark plug.

5. Dirty air filter.

6. Dirty fuel filter. 6. Replace fuel filter.

7 Water in fuel. 7. Drain fuel tank and

8. Loose or damaged wiring.

9. Carburetor out of adjustment. 9. See “To Adjust Carburetor”

10. Engine valves out of adjustment.

1. Dirty air filter.

2. Bad spark plug.

3. Weak or dead battery.

4. Dirty fuel filter. 4. Replace fuel filter.

5. Stale or dirty fuel.

6. Loose or damaged wiring.

7. Carburetor out of adjustment. 7. See “To Adjust Carburetor”

8. Engine valves out of adjustment.

1. Fill fuel tank.

before attempting to start.

5. Clean/replace air filter.

carburetor, refill tank with fresh gasoline and replace

fuel filter.

8. Check all wiring. in Service and Adjustments

section.

10. Contact a Sears or other qualified service center.

1. Clean/replace air filter.

2. Replace spark plug.

3. Recharge or replace battery.

5. Drain fuel tank and refill with fresh gasoline.

6. Check all wiring. in Service and Adjustments

section.

8. Contact a Sears or other qualified service center.

Engine will not 1. Clutch/brake pedal not 1. Depress clutch/brake

turn over

Engine clicks but

will not start 2. Corroded battery terminals.

depressed. pedal.

2. Attachment clutch is 2. Disengage attachment engaged.

3. Weak or dead battery.

4. Blown fuse.

5. Corroded battery terminals.

6. Loose or damaged wiring. 6. Check all wiring.

7. Faulty ignition switch.

8. Faulty solenoid or starter.

9. Faulty operator presence switch (es). qualified service center.

1. Weak or dead battery.

3. Loose or damaged wiring. 3. Check all wiring.

4. Faulty solenoid or starter.

clutch.

3. Recharge or replace battery.

4. Replace fuse.

5. Clean battery terminals.

7. Check/replace ignition switch.

8. Check/replace solenoid or starter.

9. Contact a Sears or other

1. Recharge or replace battery.

2. Clean battery terminals.

4. Check/replace solenoid or starter.

Page 29

TROUBLESHOOTING CHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM CAUSE CORRECTfON

Loss of power 1. Cutting too much grass/too 1. Set in “Higher Cut” position/

fast. reduce speed.

2. Throttle in “CHOKE” position.

3. Build-up of grass, leaves and trash under mower. housing.

4. Dirty air filter.

5. Low oil level/dirty oil. 5. Check oil level/change oil.

6. Faulty spark plug. 6. Clean and regap or change

7. Dirty fuel filter. 7. Replace fuel filter.

8. Stale or dirty fuel.

9. Water in fuel.

10. Spark plug wire loose.

11. Dirty engine air screen/fins. 11 .Clean engine air screen/fins.

12.Dlrty/clogged muffler. 12. Clean/replace muffler.

13. Loose or damaged wiring.

14. Carburetor out of 14.See “To Adjust Carburetor” adjustment.

15. Engine valves out of adjustment.

2. Adjust throttle control.

3. Clean underside of mower

4. Clean/replace air filter.

spark plug.

8. Drain fuel tank and refill with fresh gasoline.

9. Drain fuel tank and carbure tor, refill tank with fresh gasoline and replace fuel filter.

10. Connect and tighten spark plug wire.

13. Check all wiring.

in Service and Adjustments

section.

15. Contact a Sears or other qualified service center.

Excessive

vibration

Engine continues 1. Faulty operator-safety 1. Check wiring, switches and to run presence control system. when operator contact a Sears or other

leaves seat with with attachment

ciutch engaged

Poor cut - uneven 1. Worn, bent or loose blade. 1. Replace blade. Tighten

1. Worn, bent or loose blade.

2. Bent blade mandrel. 2. Replace blade mandrel.

3. Loose/damaged part(s).

2. Mower deck not level. 2. Level mower deck.

3. Buildup of grass, leaves, 3. Clean underside of mower and trash under mower. housing.

4. Bent blade mandrel. 4. Replace blade mandrel.

5. Clogged mower deck vent

holes from buildup of grass, leaves, and trash around mandrels.

1. Replace blade. Tighten blade bolt.

3. Tighten loose part(s). Replace damaged parts.

connections. If not qualified service center.

blade bolt.

5. Clean around mandrels to

open vent holes.

Page 30

TROUBLESHOOTING CHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION

Mower blades will 1. Obstruction in clutch 1. Re move o bstru cti on. not rotate

mechanism.

2. Worn/damaged mower

2 Replace mower drive belt.

drive belt.

3. Frozen idler pulley.

3. Replace idler pulley.

4. Frozen blade mandrel. 4. Replace blade mandrel.

Poor grass

1. Engine speed too slow.

discharge

2. Travel speed too fast.

3. Wet grass.

4. Mower deck not level. 4. Level mower deck.

5. Low/uneven tire air 5. Check tires for proper air pressure. pressure.

6. Worn, bent or loose blade.

7. Buildup of grass, leaves and trash under mower. housing.

8. Mower drive belt worn. 8. Replace mower drive belt.

9. Blades improperly installed.

10. improper blades used. 10. Replace with blades listed

11. Clogged mower deck vent 11. Clean around mandrels to holes from buildup of grass, leaves, and trash around mandrels.

Headlight(s) not

1. Switch is “OFF”. 1. Turn switch “ON”.

working 2. Bulb(s) or lamp(s) burned out. (if so equipped)

3. Faulty light switch.

4. Loose or damaged wiring.

5. Blown fuse.

1. Place throttle control in “FAST” position.

2. Shift to slower speed.

3. Allow grass to dry before mowing.

6. Replace/sharpen blade.

Tighten blade bolt.

7. Clean underside of mower

9. Reinstall blades sharp edge down.

in this manual. open vent holes.

2 Replace bulb(s) or lamp(s).

3. Check/replace light switch.

4. Check wiring and connec tions.

5 Replace fuse.

Battery will not charge

1. Bad battery ce!l(s). 1. Replace battery.

2. Poor cable connections. 2. Check/clean all connec tions.

3. Faulty regulator

3. Replace regulator.

(if so equipped).

4. Faulty alternator. 4 Replace alternator.

Engine “backfires” 1. Engine throttle control not 1. Move throttle control to when turning engine “OFF”

set at “SLOW” position for 30 seconds before to idle for 30 seconds before

“SLOW’ position and allow

stopping engine. stopping engine.

Page 31

SCHEMATIC

TRACTOR - - MODEL NUMBER 917.272850

IGNITION SWITCH

POSIT iON CIRCUIT “MAKE”

OFF M+G+A1 NONE

HUN/LIGHT B+A1 A2+L

RUN B+A1 NONE

START B + S + A1 NONE

NOTE

YOUR TRACTOR IS

EOUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST.

WIRING INSULATED CLIPS

NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR

SERVICING OF UNIT, THEY SHOULD BE REPLACED TO

PROPERLY SECURE YOUR WIRING.

HEADLIGHTS

NON-REMOVABLE

CONNECTIONS

REMOVABLE

CONNECTIONS

rtl

Page 32

ELECTRICAL

TRACTOR - - MODEL NUMBER 917.272850

Page 33

ELECTRICAL

TRACTOR - - MODEL NUMBER 917.272850

KEY

PART

NO.

1 144927 Battery 2 74760412 8 7603J

145211 Boil, Btr Front 1/4-20 x 7-1/2

150109

145769

16 176138 21

183759 22 4152J 24

4799J 25 146148 26 175158 Fuse 27

73510400 Nut Keps Hex 1/4-20 Unc 28 145491 Cable Ground

121305X Switch Seat

29 30 175566 33 140403 40 179720 41

71110408 42

131563 Cover Termina! 43 178861 Soienoid

121433X Ammeter Rectangular 6 Amp

45 52

141940 55 17490508

DESCRIPTION

BoH Hex Hd 1/4-20unc x 3/4 Case Battery

Holddown Battery Front Mount Nut, Push Nylon Battery Front 1/4 Switch, interlock Push-in Harness Light Socket (W/4152j) Buib Light #1156 Cable Battery Cable Battery

Switch Ign Key Molded Craftsman Harness Ign Boit BIk. Fin Hex 1/4-20 Unc x 1/2

Protection Wire Loop Screw Thdrol 5/16-18x1/2

NOTE: A!i component dimensions given in U. S.

inches 1 inch = 25.4 mm

Page 34

TRACTOR - MODEL NUMBER 917.272850

CHASSIS AND ENCLOSURES

Page 35

TRACTOR -

CHASSIS AND ENCLOSURES

KEY NO.

1 2 176554 Drawbar 3

5 9 168337X013

13 172105X010

18 20 180679 23 26 28 30 175692X613 Fend/Ftrest 31 139976 37 38 175710 Pivot Bracket Assembly, Rear 39

58 174930 60 64 74 STD541437 NutCrowniock 3/8016 Unc

114 158112 Keeper Belt Rear Lh St! P930

115 17060620

142 175702

143 154966

144 175582

145

159 155123X428

166 171875 206 170165 207 208 17670608 Screw Thdroi 3/8-16 x 1/2 209 211 145212 212 219 258 184245X599 259 184246X599 260 184250X428 261 184258X428

- -

MODEL NUMBER 917.272850

PART NO.

174619 Chassis 17060612 Screw 3/8-16x3/4

155272 Bumper Hood/Dash

STD533710 174996

17490608 Screw Thdroi 3/8-16 x 1/2 185682X613 Hood Assembly 184921

124028X Bushing STD541437 184247

17490508 Screw Thdroi 5/16-18x1/2 174714 72140606 Boll Rdhd Sqnk 3/8-16 Unc x 3/4

154798

156524

17670508 17000612 Screw Hexwsh Thdr 3/8-16 x 3/4 184248 Insert Lens Reflective

17000512 Screw 5/16-18x3/4

5479J

DESCRIPTION

Dash Boll, Carriage 3/8-16 x 1

Panel, Dash, L.H. Panel, Dash, R.H.

Bumper Hood Plate Mig. Battery/Tank

Nut

Grille Bracket, Fender Support

Bracket Pivot Laser Lt Duct Air Engine

Dash Lower STLT

Screw 3/8-16 x 1-1/4 Plate Reinforcement STLT Bracket Swaybar Chassis Bracket Pnt Footrest STLT Rod Pivot Chassis/Hood Cupholder Stit Black Screw Hwhd Hi-Lo #13-16 x 3/4 Boll Shoulder 5/16-18 TT Screw Thdroi 5/16-18 x 1/2 Tytt

Nut Hex Flange Lock

Lens Laser RH Lens Laser LH Cover Lens Laser Insert Grille Laser Plug, Button

NOTE: All component dimensions given in U. S.

inches 1 inch = 25.4 mm

Page 36

GROUND DRIVE

TRACTOR - MODEL NUMBER 917.272850

Page 37

GROUND DRIVE

TRACTOR - MODEL NUMBER 917.272850

KEY PART NO. NO.

2 146682 Spring, Return, Brake

123666X

3 4

12000028 121520X

17060512 Screw 5/16-18x3/4

6 8 165866

10 STD561210 11 105701X

74550412 Bolt 1/4-28 UNF W/Patch Gr. 8

13 14

10040400

16 STD541431 Nut Lock Hx W/ins 18 STD523710

STD541437

19 21 106933X 22 130804 24 STD541237

106888X Spring, Brake Rod 113

STD551037 Washer

26 27

STD561210 28 175765 29 71673

169592

30 32 STD523107 34

175578 Shaft Assembly, Foot Pedal 158 165589 Bracket Shift Mount 120183X Bearing, Nylon

STD551062 Washer

36 37

STD571810

179114

38 39 74760648 Bolt 41

175556

127783 Pulley, Idler, V-Groove, Plastic 166 166880 154407

123205X Retainer, Belt

72110612 Bolt Carr. Sh 3/8-16 x 1-1/2 Gr. 5

STD541437

51 52

STD541431

10571OX Link, Clutch 202 72110614 Bolt Carr. SH 3/8-16 x 1-3/4 Gr. 5

105709X Spring, Clutch Return 212 145212 Nut Hex Flange Lock

55 56 17060620 57

130801 V-Belt, Ground Drive

59 169691

17120614

61 62

8883R 63 175410 Pulley, Engine

DESCRIPTION

Transaxie (See Breakdown) Peerless 206-545C 65 STD551143

Pulley, Transaxle 70 134683 Ring, Retainer 74 137057

Strap, Torque 75 Rod Shifter Fender STLT 77 123583X

Pin, Cotter Washer, Shift Piate

Washer Lock Hvy Helical 5/16-18xGr.5 83 19171216

Bolt Fin Hex 84 3/8-16 Uncx 1 Gr.5 85 150360 Nut 89 158391X428 Console, Shift, STLT Knob 90 Rod, Brake 96 STD624003 Nut

Pin Rod, Parking Brake Cap, Parking Brake Bracket, Transaxle 151 19133210 Bolt 156

Roll Pin Pulley, Composite, Fiat 163 74780416 Bolt Hex Fin 1/4-20 Unc x 1 Gr. 5

Keeper, Belt, Idler Bellcrank Clutch Grnd Drv StI

Nut Crown Lock 3/8-16 Unc Nut Crown Lock 5/16-18 Unc

Screw 3/8-16x1-1/4 Keeper, Belt, Center Span

Screw 3/8-16x.875 Cover, Pedal

KEY PART NO. NO.

64 71170764 66 154778 Keeper, Belt, Engine, Fool Proof

121749X

76 STD581075

121748X

78 79 STD580025 Key Woodruff 80 145090 Arm, Shift

165592

81 82 165711 Spring, Torsion

166231

124346X Nut, Self-Thding, Wsh Hd 1/4

112

19091210

127285X 116 72140608 120 73900600 145 74490540 Bolt, Hex FIghd 5/16-18Gr.5 150 175456

166002 159 183900 Hub Tapered Flange Shift Lt

161 72140406 162

73680400

164

19091010 Washer 5/8 x .281 x 10 Ga.

165 165623

165492

168 169 165580

178394

170 197

169613

198 169593

NOTE

All component dimensions given in U. S.

inches 1 inch = 25.4 mm

DESCRIPTION

Bolt, Hex 7/16-20 x 4 Gr. 5 Washer

Guide, Mower Drive Belt, R.H. Spacer, Axle Washer 25/32 x 1-1/4 x 16 Ga. E-Ring Key, Square 2.0 x .1845/1865 Washer 25/32 x 1 -5/8 x 16 Ga

Shaft Asm Cross Tapered 650 20 Washer 17/32 x 3/4 X 16 Ga.

Link Transaxle Nut, Nylock

Retainer Spring 1” Washer 9/32 X 3/4 X 10 Ga. Strap Torque 90 Degrees Bolt Rdhd Sqneck 3/8-16 x 1 Nut Lock Fig. 3/8-16 Unc

Spacer Retainer Washer 13/32 X 2 X 10 Ga. Washer Srrted 5/16ID x 1.125

Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr.5 Nut Crownlock 1/4-20 Unc

Bracket Pivot Lever Screw 5/16-18 X 5/8 Bolt Shoulder 5/16-18 x.561 Plate Fastening Lt Keeper Belt Transaxle Gear Nyliner Snap-In 5/8 ID Washer Nyliner 7/8 ID x .105 Hd

Page 38

STEERING

TRACTOR - MODEL NUMBER 917.272850

-38

-12

-39

\ ^ ^

Page 39

STEERING

TRACTOR - MODEL NUMBER 917.272850

KEY PART NO. NO.

184704X428

172393 Axle Assembly 3 169840 Spindle Assembly, LH. 4

169839 Spindle Assembly R.H.

6266H Bearing, Race, Thrust, Hardened

121748X

6 8 12000029

175121 Draglink

10 11 STD551137 Washer, Lock 12

73940800

13 136518

145212

15 17 180641

126847X Bushing, Link, Drag

26 28 19131416

17060612 Screw 3/8-16x3/4

29 30 STD561210 32

130465 36 155099 37 152927 Screw 38 159946X428 Insert, Steering Wheei

19182411 Washer 9/16 ID x 1-1/2 OD 11 Ga.

STD541537 Nut Lock Center 3/8-24 Unf

40 41

159945 42

145054X428

121749X Washer 25/32 x 1-1/4 x 16 Ga.

43 44

180640 46 184946X428 Cap, Spindle 51 73540400 54

71130420

160367

65 67

72140618

169827

68 71

175146 82

169835 Bracket Susp- Chassis Front 87

173966 88 175118 Bolt Shoulder 7/16-20 Unc 91 175553

DESCRIPTION

Steering Wheei

Washer 25/32 x 1-5/8 x 16 Ga. Ring, Klip

Nut Hex Jam Topiock 1/2-20 Unf Spacer Bearing Axle Front Nut, Hex Flange Lock Shaft Assembly Steering

Washer 13/32 X 7/8 X 16 Ga. Pin Cotter

Rod, Tie Bushing, Steering

Adaptor, Steering Wheel Boot, Steering Shaft

Extension Shaft Steering NutCrowniock 1/4-28

Bolt Hex 1/4-28 UNF X 1-1/4 Gr. 8 Spacer Brace Axle Bolt RDHD Sqnk 3/8-16 x 2-1/4 Axle, Brace Steering Asm-

Washer Flat .781 x 1-1/2 x .14 Clip Steering

NOTE: All component dimensions given in U.S. inches

1 inch = 25-4 mm

Page 40

ENGINE

TRACTOR - MODEL NUMBER 917.272850

OPTIONAL EQUIPMENT

Spark Arrester

1 1 1 r^i

c;-I I iCh

Page 41

ENGINE

TRACTOR - MODEL NUMBER 917.272850

KEY PART NO. NO.

170546X505 Control, Throttle Paddle

17720408 3 4

149723 5 159955 Exhaust Asm. Left 6 160589 Exhaust Asm. Right

171877 Bolt 5/16-18unc X 3/4 W/Sems

162797

10 13 165391 14

148456 Tube Drain Oil Easy

STD551237 Washer Lock Ext Tooth 3/8

16 17 17060624 Screw 3/8-16 X 1-1/2

169837

23 25 145996X505 Control Choke 26 73920600 29 137180 31 157103 32

161696 Cap Fuel Guage

123487X

33 34 106082X Spacer Pad 37

8543R Line, Fuel

181654

109227X

17000612

45 72

183906 81 73510400

DESCRIPTION

Screw, HexThd Cut 1/4-20x 1/2 Engine, B&S, (See Breakdown) No. 407777-0174-El Muffler Exhaust

Heat Shield Lt Gasket, Muffler

Shield, Brn/Dbr Guard

Nut Keps 3/8-24 Unf Arrestor, Spark Tank, Fuel

Clamp, Hose

Plug, Oil Drain Easy

Pad idler

Screw Hex Wsh3/8-16 x 3/4

Screw Socket Head 5/16-18x1

Nut Keps Hex 1/4-20 Starter Nut

NOTE

; Al! component dimensions given in U. S.

inches 1 inch = 25.4 mm

Page 42

SEAT ASSEMBLY

TRACTOR - MODEL NUMBER 917.272850

KEY

PART

NO.

1 180597

180166 Bracket Pnt Pivot Seat (b!k) 13 3 71110616 4

19131610 Washer 13/32 X 3/4 X 10 Ga 15 134300 Spacer Split 28 X 96 Zinc 5 145006 Clip Push in Hinged 16

STD541437

6 7 124181X 8 17000616

19131614 Washer 13/32 X 1 X 14 Ga

1011180186

166369

DESCRIPTION

Seat 12 121246X Bolt Fin Hex 3/8-16uno X 1

Nut Hex Lock w/lns 3/8-16 Unc 17 123976X Spring Seat Cprsn 2 250 BIk Zi Screw 3/8-16 X 1

Pan Pnt Seat (bik) Knob Seat Adj Wingnut

KEY

PART

NO.

121248X

14 72050412

121250X Spring Cprsn 1 27 Bik Pnt

21 171852 22

STD541431

24 19171912 Washer 17/32 X 1-3/16 X12Ga.

DESCRIPTION

Bracket Pnt Mounting Switch Bushing Snap Bik Nyl 50 id Bolt Rdhd Sht Nk 1/4-20x1-1/2

Nut Lock 1/4 Lge Fig Gr 5 Zinc

Bolt Shoulder 5/16-18 Unc-2A

Nut Hex Lock w/ins 5/16-18

NOTE: Ail component dimensions given in U.S.

inches 1 inch = 25.4 mm

Page 43

DECALS

TRACTOR - MODEL NUMBER 917.272850

2 7

KEY

PART

NO.

156368

2 186437

3 186280 Decal, Hood, R.H. 15 160396 4

186281 Decal, Hood, L.H. 138047

133644

6 7

186869 Decal, Chassis

8 172331

186282 Decal, Fender, Craftsman 165800X428

9 10 156439 11

186283 Decal, Hood Side

172258 Decal, HP Engine

DESCRIPTION

Decal, Oper. Instr. Decal, Replacement

Decal, Battery Decal, Customer Maintenance

Decal, Mower Srs Decal, Fender Danger

WHEELS AND TIRES

PART

NO.

13 146046 Decal, V-Be!t Drive Schematic 14

179128 184842

16 17

184843 Decal, Grille LH 18 164065 19 149516

138311 Decal, Lift Handle

- -

165799X428

- -

184950 Owner's Manual, English

184951

- -

KEY PART NO. NO.

59192

65139

106222X

3 4

59904 106732X624

278H

9040H

106108X624

122082X

7152J

104757X428 144334

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

DESCRIPTION

Decal, Deck B 42” Decal, V-Bell Schematic Decal, Grille RH

Decal, Strg.Whl Decal, Battery Dngr/Psn Eng

Pad Footrest LH STLT Pad Footrest RH STLT

Owner's Manual, Spanish

DESCRIPTION

Cap Value Tire

Stem Value Tire FTs 15 X 6 0 - 6 Service Tube inner Front #35060

Rim Asm 6"front White Service

Fitting Grease

Bearing Flange

Rim Asm 8“rear White Service Tire RTs 20 X 10-8 Service Tube Rear 9 5X8 Service Cap Axle BIk 1 50 X 1 00

Seaiant, Tire (10 oz. tube)

Page 44

LIFT ASSEMBLY

TRACTOR - MODEL NUMBER 917.272850

Page 45

LIFT ASSEMBLY

TRACTOR - MODEL NUMBER 917.272850

KEY

PART

NO.

159460

2 159471

105767X

3 4 12000002 E Ring #5133-62

19211621 Washer 21/32 x 1 x 21 Ga.

120183X Bearing Nylong

6 7 125631X

122365X Button Plunger Read

139865

139866 13 STD624008 15 173288 16 73350800 17

175689 18 73800800 19 139868

163552 Retainer Spring

20 31 169865 32

73540600

DESCRIPTION

Washer Asm Inner Spring W/Plunger

Shaft Asm. Lift Pin Groove

Grip Handle Fluted Link Asm Lift L.H.

Link Asm Lift R.H. Retainer Spring Link Front Nut Jam Hex 1/2-13 Unc

Trunnion BIk Zinc

Nut Lock w/Wsh 1/2-13 Unc

Arm Suspension Mower

Bearing, Pvt. Lift Nut Crownlock 3/8-24

NOTE: Ail component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 46

MOWER DECK

TRACTOR - MODEL NUMBER 917.272850

Page 47

TRACTOR - MODEL NUMBER 917.272850

MOWER DECK

KEY PART KEY PART NO. NO.

1 165892 Mower Deck Assembly, 42” 59 141043

2 STD533107

138017

3 4

165460

5 STD624008

178024 Bar Sway Deck 103 19061216

850857

STD551137 Washer, Lock 105 160793

10 140296

134149 Blade, 42” MulchingStd (For

139775

- -

138971 Blade, 42” Hi-Lift (For bagging or 118 73930600

13 137645 Shaft Assembly, Mandrel, Vented 14 128774

110485X

15 16 174493 18 72140505 Bolt, Carriage 5/16-18 x 5/8

132827

19 20 159770 21

STD541431 23 177563 Bracket, Deflector 24 105304X

123713X Spring, Torsion, Deflector

110452X

26 27

130968X428 28 19111016 Washer 11/32 x 5/8 x 16 Ga. 29 131491 Rod, Hinge

173984 Screw Thdrol Washer Head 154

30 31 129963 32

153535 Pulley, Mandrel

178342 Nut, Toplock, Flanged

33 34 STD533717

131494 Pulley, Idler, Flat 159

36 37 STD551037 Washer 13/32 x 13/16 x 16Ga.

STD541437

40 44

140088 Guard, Mandrel, L.H. 45 STD624003 46 137729 Screw, Thd. Roll 1/4-20x5/8

133944

139888

184907 Arm Assembly, Pad, Brake

53 54

178515 Washer, Hardened

55 155046 56 165723

DESCRIPTION

Bolt Bracket Assembly,Sway Bar, Front Bracket Sway Bar 38/42” Deck Retainer Spring

Bolt, Hex 3/8-24 X 1.25 Gr.8 Washer, Hardened

(The following blades are available)

mulching mowers only) Blade, 42" Mulching Premium (For better wear when mulching) 117

discharing) 119 Housing, Mandrel, Vented

Bearing, Bali, Mandrel Stripper, Vented Mower Deck

Bolt, Shoulder Baffle, Vortex Nut Crownlock 5/16-18 UNC

Cap, Sleeve Nut, Push

Shield, Deflector

Washer, Spacer 155

Bolt

Nut Crownlock 3/8-16 UNC Retainer Washer, Hardened

Bolt, Shoulder 5/16-18 UNC

NO. NO.

67 68 144959 92 STD541437

101 136420 102

104 106 2029J Nut, Weld

111 179292 112 113 17060510 114 116

129 130 STD523710 Bolt, Fin Hex 3/8-16 Unc x 1 Gr. 5 131 STD533710 Bolt, Rdhd Sqnk 3/8-16UNC x1 142 143 157109 144 158634 Keeper Belt 42” Clutch Cable 145 165888 Pulley Idler Flat 146 147 148 149 165898 150 19091216 Washer 9/32 x 3/4 x 16 Ga. 151 169670 Bracket Clutch 152 153

156 157 158 17720408

184

- -

NOTE: All component dimensions given in U.S. inches

Arm, Idler Spacer, Retainer

184939

71081010 STD551110

179293 73510500

4898H Bolt Shoulder 165746 Wheel Gauge Std

19121414 19131312 Washer 13/32 x 13/16 x 12Ga.

165890

171977 131335

169022 Spring Return Idler

169676 169674

169675 169671 Spring Retention Lever 169672 Spacer 169669

72140614 19131410 Washer 13/32 x 7/8 x 10 Ga.

130794

169583

DESCRIPTION

Guard, TUV idler Knob Custom Oval V-Belt Nut Mulcher Cover

Screw Washer #10 Washer, Lock

Latch Assembly, Bagger

Bracket Gauge Wheel Lh

Bracket Gauge Wheel Rh

Screw 5/16-18 Unc

Nut Keps 5/16-18 Unc

Nut Centerlock 3/8-16 Unc Washer 3/8 x 7/8 x 4 Ga.

Arm Spring Brake Mower

Bracket Arm Idler 42”

Bolt Carriage Idler

Spring Extension

Retainer Spring Yellow Zinc

Cable Clutch 42 In Washer Flat 3/8” Type B

Spring Retainer

Rod Clutch

Screw Hex Thd Cut 1/4-20 x 1/2

Bolt Rdhd Sqn 3/8-16 Unc x 3/4

Mandrel Assembly (Includes Hou

sing, Shaft and Shaft Hardware

Only - Pulley Not included)

Replacement Mower, Complete

1 inch = 25.4 mm

Page 48

TRACTOR - MODEL NUMBER 917.272850

PEERLESS TRANSAXLE-MODEL NUMBER 206-545C

0—27

<0)^29

20-t “I

® 7U SA IJ ^

1BT -VO JJ «.

150

1S0-^

Page 49

TRACTOR - MODEL NUMBER 917.272850

PEERLESS TRANSAXLE-MODEL NUMBER 206-545C

KEY PART NO. NO.

1 772147 2 780086A 3 770128 Transaxle Case 4

776395 Countershaft

5 776409 Output Shaft

778364 Spur Gear {38 teeth)

6 6A

778369

778330 8 792180 8A 792047

784352

10 784378 Shift Rod & Fork 11 778334 Bevel Gear (30 teeth) 12

778309

13 778368 14

778368

15 778370 17

786188

786102

792077A

20 21

792078 22

792079

792073A Screw 1/4 - 20 X 1-1/4”

25 25A 792177 26 792125 27

792035 28 788040

780072

29 29A

780160 Thrust Washer 29B

780051 29C 780199

30 780108 31 780001 31A

780195 32

788083 Oil Seal 5/8” 34 780194 35 780193 35A 780197 Flanged Bushing .751 36 790075 Brake Disk 37 790007

799021

DESCRIPTION

Transaxie Cover Needle Bearing 5/8”

Spur Gear {15 teeth) Spur Gear {11 teeth) Shift Key Woodruff Key #9 Shift Collar

Input Bevel Pinion (13 teeth) Bevel Gear (13 teeth) (Include. 14) Bevel Pinion (13 teeth) (Include. 13) Ring Gear (43 teeth) Drive Pin Spacer 1.130 X .695 Ball 5/16” dia Set Screw 3/8 -16 x 3/8” Spring .310 OD X .625 L

Screw 1/4-20 X 1-3/8” Retaining Ring (pkg of 2) Retaining Ring Retaining Ring Thrust Washer .627 IDX.031W

.762 IDX.031W Thrust Washer .762 IDX.031W Anti-Rotation Washer .632 Cup Washer

1.127 IDx .032W Flat Washer .750 ID x .056W (Use As Needed) Flat Washer .750 ID X .062W

Bushing .563 Flanged Bushing 5 / 8” ID

Brake Pad Plate Brake Pad (pkg of 2)

KEY PART

NO. NO.

39 786026

792076A

40 41A

790079 Brake Lever

42 792073A Screw 1/4 - 20 X 1-1 /4”

42A 792085A Screw 1/4 - 20 X 2 1/4" 43 792075 44

790025 45 786066 Spacer .2625 x 1.0 46 786086 Brake Lever Bracket

774690 Axle (11-15/16” Long)

48 774691 49 778356 50 778338

778354 Spur Gear (23 teeth)

51 52 778352 Spur Gear (19 teeth)

53 778350 54

778346 56 778355

57 778337 Spur Gear (13 teeth) 58 778353 59 778351 60 778349

61 778345

65 780189

776422

66 67

776396

69 792170

786187 Spacer .890

788069

71B 788092

76 780090 77 788078A Inverted Retaining Ring

792144 Spring .430 OD x .5000 L

778333

83 778338

792154

85 87 788089A

788093A

150 157 788088A

730229A

180

794712

900

DESCRIPTION

Dowel Pin Flat Washer .312 ID x .059W

Locknut 5/16-24 Brake Pad Holder

Axle (16 -1 / 2” long)

Spur Gear (29 teeth) Spur Gear (27 teeth)

Spur Gear (16 teeth) Spur Gear (15 teeth) Spur Gear (11 teeth)

Spur Gear (17 teeth) Spur Gear (21 teeth) Spur Gear (24 teeth) Spur Gear (25 teeth) Flat Washer .563 ID X .062W Input Shaft Shifter & Brake Shaft Retaining Ring

Square Cut Ring “0” Ring Flat Washer

1.128 IDX.058W

Bevel & Spur Gear (30 & 13

teeth)

Spur Gear (27 teeth) Oil Fill Plug Oil Seal 9/16” Liquid Gasket RTV Silicone Oil Seal 3 /4” Gear Oil 80W90 Replacement MST

206-545C Transaxle

NOTE: All component dimensions given in U.S

inches 1 inch = 25.4 mm

Page 50

TRACTOR - MODEL NUMBER 917.272850

BRIGGS & STRATTON ENGINE-MODEL NUMBER 407777, TYPE NUMBER 0174-El

Page 51

TRACTOR - MODEL NUMBER 917.272850

BRIGGS & STRATTON ENGINE-MODEL NUMBER 407777, TYPE NUMBER 0174-El

1023A|

209

227 1

505 ®

914 <

LfiJ 562

1022

121 CARBURETOR OVERHAUL KIT

150 i p"

104 “ 105 I

117 _ 137

977 CARBURETOR GASKET SET

=’COD]

276 m

633 ® 987 ®

1123 1124 99

633 ® 987 ®

137 0

ISO 1 276 ^

1123 o 1124 99

1128 1

125 I

616

552 0

552A ©

742

404 O

552A e

691 ®

1169 1

«^C73>

Ql^=^===e

co^o:

105 i

135 I

1124

1126 '

1123 ©

160 @

117

118 ^

131 1 130 . 95 V

142 1 P

1128 1 Ji

150 [

987 ^ 'O O

Page 52

TRACTOR - MODEL NUMBER 917.272850

BRIGGS & STRATTON ENGINE-MODEL NUMBER 407777, TYPE NUMBER 0174-El

789

1070

573

405

363

Page 53

TRACTOR - MODEL NUMBER 917.272850

BRIGGS & STRATTON ENGINE-MODEL NUMBER 407777, TYPE NUMBER 0174-El

KEY PART NO. NO.

690231

499585 Kit-Bushing/Seal (Magneto Side) 3 391086 • Seai-Oi! (Magneto Side) 4

690069 Sump-Engine

5 693998 5A

693999 7 690962

8 499601

690937 • Gasket-Breather

10 690960 11 690942 Tube-Breather 12 697227 13 690360 15 690946 Piug-Oi! Drain 16 691046 Crankshaft

690947

20 22

694966

691054

23 24

222698 Key-Flywheel 25 499588 Piston Assembly (Standard) 25 499589

25 499590 25 499591

499604

26 26 499605 26 499606 Ring Set-Piston (.020” Oversize)

499607

26 27

690975 28 690229 29 499583 32

690976 33 499596 Valve-Exhaust 34 499597 35 690963 Spring-Valve (Intake) 36 690963 Spring-Valve (Exhaust)

690964

40 42

499586 Keeper-Valve

690977

45 46 690978 Camshaft

692714 Short Block (446777-0027-E2

695241

50 51 690950 Gasket-Intake 53 690951 54

695240 73 691055 74 691057 Screw (Rotating Screen) 75 691056 Washer (Flywheel) 89 690283 Plug-Oil 95 690718

499802

104 690984 105 690985 108 690986 Valve-Choke 117 690232

DESCRIPTiON

Cylinder Assembly

Head-Cylinder (Cylinder 1) Head-Cylinder (Cylinder 2)

•+ Gasket-Cylinder Head Breather Assembly

Screw (Breather Assembly)

• Gasket-Crankcase Screw (Cylinder Head)

• Seal-Oil (PTO Side) Screw (Engine Sump) Flywheel

Piston Assembly (.010” Over size) Piston Assembly (.020” Over size) Piston Assembly (.030” Over size) Ring Set-Piston (Standard) Ring Set-Piston (.010” Oversize)

Ring Set-Piston (.030” Oversize) Lock-Piston Pin Pin-Piston Rod-Connecting Screw (Connecting Rod)

Valve-Intake

Retainer-Valve

Tappet-Valve

Replacement Engine) Manifold-intake

Stud (Carburetor) Screw (intake Manifold) Screen-Rotating

Screw (Throttle Valve) Kit-ldle Speed

Pin-Float Hinge

Vaive-Fioat Needle

Jet-Main (Standard)

KEY PART NO. NO.

118 690989 121

499811 499804 Carburetor

125 130 690993 Valve-Throttle 131 499805 Kit-Throttle Shaft 133 499806 135 499803 137 690994 141 499807 142

499808 146 690979 150 690995 160 690996 Retainer-Solenoid 163 691001 165 693148 187

691050 Line-Fuel (Cut to Required 187A

691049 Line-Fuel (Molded) 188 690960 192

690083

697674 Spring-Governor

209 211

691019

212

695238 Link-Throttle

691021

213

691022

216 219 696376

690412 Washer (Governor Lever)

220 222

691023 Bracket-Control

227

691048

231 690718 Screw (Choke Valve) 240 691035 Filter-Fuel

690957 Retainer-Breather

250 252

690956

691024 Clamp-Casing

265 267 695134 Screw (Casing Ciamp)

690997

276 287

690960

304 695277 Housing-Blower 305 691005

691262 Motor-Starter

309 310 691263 311 497608

332

691059

333 691060 Armature-Magneto 334

691061 Screw (Magneto Armature)

337

691043

694012

358

691062

363 383 690966 385 690960

RPM Settings:Low Speed: 1900-2100

•

Inciuded in Engine Gasket Set, Key. No. 351

Inciuded in Carburetor Overhaul Kit, Key. Ni

121

Included in Carburetor Gasket Set, Key. No.

977

Included in Valve Gasket Set, Key. No. 1095

DESCRIPTION

Jet-Main (High Altitude)

Kit-Carburetor Overhaul

Float-Carburetor

Tube-Fuel Transfer

Gasket-Float Bowl

Kit-Choke Shaft

Nozzie-Carburetor

Key-Timing

Gasket-Nozzle

•+ Gasket-Air Cieaner Nut (Ring Gear)

Length) Screw (Control Bracket)

Adjuster-Rocker Arm

Spring-Governed Idle Bracket-Choke Control

Link-Choke Gear-Governor

Lever-Governor Control

Collector-Oil

•0+

Washer-Sealing

Screw (Dipstick Tube) Screw (Blower Housing) Bolt-Starter Motor

Brush Set Nut (Flywheel)

Spark Plug Set-Engine Gasket Flywheel Puller

Wrench-Spark Plug

Screw (Fuel Pump) High Speed: 3000-3200

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 54

TRACTOR - MODEL NUMBER 917.272850

BRIGGS & STRATTON ENGINE-MODEL NUMBER 407777, TYPE NUMBER 0174-El

KEY PART NO. NO.

387

808656 Pump-Fue! 404 690442 Washer (Governor Crank) 405 690960 418 690999 445 499486 447

691003 447A

690960 467

691008 474

696459 505 691029 510 497606

692024

513 523 691036 524 691032

691037 Tube-Dipstick

525 544 Armature-Starter (Service with 1005 499603 Fan-F!ywheel

552 690552 Bushing-Governor Crank 552A

690553 562

690311 573 691009 601 691038 Clamp-Hose

690317 Retainer-Governor Shaft

615 616 691045 617 691917 628 690960 Screw (Fuel Pump Bracket) 633 690998 635 66538 Boot-Sparkplug 654

690958 668 691215 672 690234

690657 • Seal-Governor Shaft

691 695 693149

697 690372 703 691010 Clip 718 690959

499612 Gear-Ring

726 741

690980 742

690328 750 696999 783 693058 788 691039 Bracket-Fuel Pump 1169 693140 789 695050 797

691029 797A 693167 Nut (Brush Retainer)

690967 Screw (Rocker Arm)

798 801 691283 Cap-Drive 0 802

691286 Cap-End 803

842

691031 • Seal-Dipstick/Tube 847 499602 851 493880 Term inal-Sparkpiu g 855 691011

691012

865

DESCRIPTION NO. NO.

Screw (Back Plate)

Plate-Carburetor

Filter-Air Cleaner Cartridge 918 694000 Screw (Air Guide Cover) Screw (Air Guide Cover) Knob-Air Cleaner 943 690589 Alternator 947

Nut (Governor Control Lever) 965 499613

Drive-Starter 967 Clutch-Drive

Dipstick 975 499810 Bowl-Float

• Seal-Dipstick Tube

691262 Starter Motor) 1013 Bushing-Governor Crank

Bolt (Governor Control Lever)

Plate-Back 1023 499599

Crank-Governor Seal-0 Ring (Intake Manifold)

Seal-Choke/Throttle Shaft 1029

Nut (Carburetor) Spacer 1051 691265

Gasket-Carburetor Plate

Screw (Ring Gear) 1090 691293 Screw (Drive Cap)

Pin-Locating 1119 691183 Gear-Timing

Retainer-E Ring 1126 690991 Screw (Oil Pump Cover) Gear-Pinion 1128 690990

Harness-Wiring

Nut (Brush Retainer)

Housing-Starter (Service with 691262 Starter Motor) 977

Dipstick/Tube Assembly Adapter-Air

Cover-Air Guide

KEY PART

DESCRIPTION

865A 691014 Cover-Air Guide 865B

691015 868 690968 *-h Seal-Valve 914 691127 Screw (Rocker Cover)

929 695239 Screw (Choke Control Bracket) 929A

691003 Screw (Choke Control Bracket)

499809 Solenoid-Fuel

272638 Filter-Pre Cleaner

968 499788 977 499812 Gasket Set-Carburetor

987

691000

690954

1017

690770 Screen-Oil Pump

1019 690103 Klf-Label 1022 690971 •-I- Gasket-Rocker Cover

1023A499600

1024 499054

1026 690981

1026A690982 Rod-Push (Aluminum)

1027 492932

690972 Arm-Rocker

691042 Shaft-Pump

1035

695704 Label-Emission

1036

274794

1058

691674

1070 1095 694013 Kit-Valve Overhaul

1100 690973

690987

1123 1124

690988 0t Seal-0 Ring (Fuel Transfer Tube)

1127 690992

RPM Settings:Low Speed: 1900-2100

•

included in Engine Gasket Set, Key. No. 358

included in Carburetor Overhaul Kit, Key. No.

121

included in Carburetor Gasket Set, Key No.

Ч-

included in Valve Gasket Set, Key No. 1095

NOTE:

: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Cover-Air Guide

Hose-Vacuum

• Seal-0 Ring (Oil Pump Cover) Cover-Oil Pump Cover-Air Cleaner

Seal-Throttle Shaft

Nipple-Oil Filter

Cover-Rocker (Cylinder 1) Cover-Rocker (Cylinder 2) Pump-Oil Rod-Push (Steel)

Fiifer-Oil

Ring-Retaining Owner’s Manual Screw (Flywheel Fan) Retainer-Brush

Pivot-Rocker Arm Screw (Alternator)

0t Seal-0 Ring (Solenoid Retainer)

Screw (Fuel Transfer Tube) Screw (Float Bow!)

0 Screw (Carburetor Nozzle)

Screw (Carburetor Cover Plate) High Speed: 3000-3200

Page 55

Cn cn

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

. ' ■ . . . ■ ■ . - i I . I . . ■ ■ . ■ ' . - L . .... .... ..... .. .

... .... .. ...... I . , . , ^ . , - 1 . I . r

vrvnv^^

WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes.

1. Fold this page along dotted line indicated above.

2. Hold page before you so that its left edge is vertically parallel to a tree

trunk or other upright structure.

3. Sight across the fold in the direction of hill slope you want to measure.

4. Compare the angle of the fold with the slope of the hill.

Page 56

Get it fixed, at your home or ours!

Your Home

For repair - in your home - of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner’s manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME® Anytime, day or night

(1-800-469-4663) (U.S.A. and Canada)

www.sears.comwww.sears.ca

Our Home

For repair of carry-in products like vacuums, lawn equipment,

and electronics, call or go on-line for the nearest

Sears Parts and Repair Center.

1 -800-488-1222 Anytime, day or night (U.S.A. only)

www.sears.com

To purchase a protection agreement (U.S.A.)

or maintenance agreement (Canada) on a product serviced by Sears:

1 -800-827-6655 (U.S.A) 1 -800-361-6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

1-888-SU-HOGARS^

(1-888-784-6427)

® Registered Trademark / ™ Trademark / Service Mark of Sears, Roebuck and Co. ® Marca Registrada / Marca de Fábrica / Marca de Servicio de Sears, Roebuck and Co.

Marque de commerce / “ Marque déposée de Sears, Roebuck and Co.

Au Canada pour service en français:

1-800-LE-FOYER'^^

(1-800-533-6937)

www.sears.ca

184950 Rev. 4 05.23.03 TR/MH/TR

Printed in U.S.A.

Craftsman 917.272850 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

DO NOT:

ATTACH STEERING WHEEL

INSTALL SEAT

L |\|

STOPPING

TO USE THROTTLE CONTROL

TO MOVE FORWARD AND BACKWARD

TO ADJUST MOWER CUTTING HEIGHT

TO ADJUST GAUGE WHEELS

TO OPERATE MOWER

TO TRANSPORT

ADD GASOLINE

OPERATOR PRESENCE SYSTEM

BLADE CARE

BLADE REMOVAL

BATTERY

TRANSAXLE COOLING

LUBRICATION

ENGINE OIL FILTER

AIR FILTER

MUFFLER

SPARK PLUG(S)

IN-LiNE FUEL FILTER

CLEAN AIR INTAKE/COOLING AREAS

TO REMOVE MOWER

TO INSTALL MOWER

TO LEVEL MOWER HOUSING

TO REPLACE MOWER BLADE DRIVE

BELT

TO CHECK AND ADJUST BRAKE

TRAL ADJUSTMENT

TO REMOVE WHEEL FOR REPAIRS

TO REPLACE HEADLIGHT BULB

TO ADJUST THROTTLE CONTROL CABLE

TO ADJUST CARBURETOR

ENGINE OIL

SCHEMATIC

GROUND DRIVE

STEERING

ENGINE

DECALS

WHEELS AND TIRES

MOWER DECK

Get it fixed, at your home or ours!

Your Home

Our Home