Craftsman 917271652 Owner’s Manual

Owner's Manual

ICRIIFTSMI W J

LAWN TRACTOR

17 HP, 42" Mower Electric Start

6 Speed Transaxle

Model No.

917.271652

differently from previously built engines. Before you start the en-

This product has a low emission engine which operates

gine, read and understand this Owner's Manual.

CAUTION: Read and follow all Safety

Rules and Instructions before operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, II 60179 U.S.A.

Visit our Craftsman website:www.sears.com/craftsman

For answers to your questions about this product, Call:

1-800-659-5917

Sears Craftsman Help Line 5 am- 5 pm, Mon- Sat

Warranty................................................2

Safety Rules .......................................... 3

Product Specifications ........................... 6

Assembly/P re-Operation ....................... 8

Operation ............................................. 11

Maintenance Schedule ....................... 17

LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT

For two (2) years from the date of purchase, if this Craftsman Riding Equipment is maintained, lubricated and tuned up according to the instructions in the owner's manual, Sears will repair or replace free of charge any parts that are found to be defective in material or workmanship according to the guidelines of coverage listed below. Sears will also provide free labor for these applicable warranted parts for the two full years. During the first 30 days of purchase, there will be no charges to service the product at your home for issues covered by this warranty. (See exclusions below).

For your convenience, IN HOME warranty service will still be available after the first 30 days of purchase, but a trip charge will apply. This charge will be waived if the Crafts- man product is dropped off at an authorized Sears location. For the nearest authorized

Sears location, please call 1-800-4-MY-HOME®. This warranty applies only while this product is within the United States.

This Warranty does not cover:

• Expendable items which become worn during normal use, including but not limited

to blades, spark plugs, air cleaners, belts, and oil filters.

• Standard Maintenance Servicing, oil changes, or tune-ups

• Tire replacement or repair caused by punctures from outside objects, such as nails,

thorns, stumps, or glass.

• Repairs necessary because of operator abuse, including but not limited to, damage

caused by towing objects beyond the capability of the riding equipment, impacting objects that bend the frame or crankshaft, or over-speeding the engine.

• Repairs necessary because of operator negligence, including but not limited to,

electrical and mechanical damage caused by improper storage, failure to use the

proper grade and amount of engine oil, failure to keep the deck clear of flammable

debris, or failure to maintain the equipment according to the instructions contained in the owner's manual.

• Engine (fuel system) cleaning or repairs caused by fuel determined to be contami- nated or oxidized (stale). In general, fuel should be used within 30 days of its

purchase date.

• Normal deterioration and wear of the exterior finishes, or product label replacement.

• Riding equipment used for commercial or rental purposes.

LIMITED WARRANTY ON BATIERY For ninety (90) days from date of purchase, if any battery included with this riding

equipment proves defective in material or workmanship and our testing determines the battery will not hold a charge, Sears will replace the battery at no charge. During the

first 30 days of purchase, there will be no charges to replace the battery at your HOME.

After the first 30 days, for your convenience, IN-HOME warranty service will still be available but a trip charge will apply. This charge will be waived if the Craftsman

product is dropped of at an authorized Sears location. For the nearest authorized Sears location, please call 1-800-4-MY-HOME®.

Maintenance ........................................ 17

Service and Adjustments ..................... 21

Storage ................................................ 27

Troubleshooting .................................. 28

Repair Parts ......................................... 32

Sears Service ....................... Back Cover

This battery warranty applies only while this product is within the United States. This warranty gives you specific legal rights, and you may also have other rights, which

vary, from state to state.

Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, iL 60179

IMPORTANT: This cutting machine is capable of amputating hands and feet and

throwing objects. Failure to observe the following safety instructions could result in

serious injury or death.

Look for this symbol to point out

important safety precautions. It means CAUTION!!! BECOMEALERT!H YOUR

SAFETY IS INVOLVED.

CAUTION: In order to prevent

accidental starting when setting up,

transporting, adjusting or making repairs, always disconnect spark plug wire and

place wire where it cannot contact spark plug.

& CAUTION: Do not coast down a hill

in neutral, you may lose control of the

tractor.

,_ CAUTION: Tow only the attachments that are recommended by and comply

with specifications of the manufacturer of your tractor. Use common sense when

towing. Operate only at the lowest possible speed when on a slope. Too

heavy of a load, while on a slope, is

dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

_IbWARNING: Engine exhaust, some of

its constituents, and certain vehicle components contain or emit chemicals

known to the State of California to cause cancer and birth defects or other repro-

ductive harm.

WARNING: Battery posts, terminals

and related accessories contain lead and lead compounds, chemicals known

to the State of California to cause cancer and birth defects or other reproductive

harm. Wash hands after handling.

I. GENERAL OPERATION

• Read, understand, and follow all

instructions in the manual and on the machine before starting.

• Only allow responsible adults, who are

familiar with the instructions, to operate the machine.

• Clear the area of objects such as rocks,

toys, wire, etc., which could be picked up and thrown by the blade.

• Be sure the area is clear of other people before mowing. Stop machine if anyone

enters the area.

• Never carry passengers.

• Do not mow in reverse unless absolutely necessary. Always look down and

behind before and while backing.

• Be aware of the mower discharge direction and do not point it at anyone.

Do not operate the mower without either

the entire grass catcher or the guard in

place.

• Slow down before tuming.

• Never leave a running machine unattended. Always turn off blades, set

parking brake, stop engine, and remove

keys before dismounting.

• Turn off blades when not mowing.

• Stop engine before removing grass

catcher or unclogging chute.

• Mow only in daylight or good artificial

light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Watch for traffic when operating near or crossing roadways.

• Use extra care when loading or unload- ing the machine into a trailer or truck.

• Data indicates that operators, age 60 years and above, are involved in a large

percentage of riding mower-related injuries. These operators should

evaluate their ability to operate the riding mower safely enough to protect them-

selves and others from serious injury.

• Keep machine free of grass, leaves or other debris build-up which can touch

hot exhaust / engine parts and burn. Do not allow the mower deck to plow leaves

or other debris which can cause build- up to occur. Clean any oil or fuel

spillage before operating or storing the machine. Allow machine to cool before

storage.

II. SLOPE OPERATION

Slopes are a major factor related to loss-of- control and tipover accidents, which can re- sult in severe injury or death. All slopes require extra caution. If you cannot back up

the slope or if you feel uneasy on it, do not mow it.

DO:

• Mow up and down slopes, not across.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall

grass can hide obstacles.

• Use slow speed. Choose a low gear so that you will not have to stop or shift

while on the slope.

• Follow the manufacturer's recommenda- tions for wheel weights or counter-

weights to improve stability.

• Use extra care with grass catchers or other attachments. These can change the stability of the machine.

• Keep all movement on the slopes slow and gradual Do not make sudden changes in speed or direction.

• Avoid starting or stopping on a slope. If tires lose traction, disengage the blades

and proceed slowly straight down the slope.

DO NOT:

• Do not turn on slopes unless necessary,

and then, turn slowly and gradually downhill, if possible.

• Do not mow near drep-offs, ditches, or embankments. The mower could

suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge

caves in.

• Do not mow on wet grass. Reduced traction could cause sliding.

• Do not try to stabilize the machine by putting your foot on the ground.

• Do not use grass catcher on steep slopes.

Ill. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children.

Children are often attracted to the machine and the mowing activity. Never

assume that children will remain where you last saw them.

• Keep children out of the mowing area and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and when backing, look behind

and down for small children.

• Never carry children. They may fall off and be seriously injured or interfere

with safe machine operation.

• Never allow children to operate the

machine.

• Use extra care when approaching blind

corners, shrubs, trees, or other objects that may obscure vision.

IV. SERVICE

• Use extra care and other fuels. They are flammable and vapors are explosive.

-Use only an approved container.

- Never remove gas cap or add fuel with the engine running. Allow

engine to cool before refueling. Do

not smoke.

-Never refuel the machine indoors.

- Never store the machine or fuel

container inside where there is an open flame, such as a water heater.

• Never run a machine inside a closed area.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep

equipment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel

spillage. Allow machine to cool before storing.

• Stop and inspect the equipment if you strike an object. Repair, if necessary,

before restarting.

• Never make adjustments or repairs with the engine running.

• Grass catcher components are subject

to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently

check components and replace with manufacturer's recommended parts,

when necessary.

• Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and

use extra caution when servicing them.

• Check brake operation frequently. Adjust and service as required.

in handling gasoline

• Be sure the area is clear of other people before mowing. Stop machine if

anyone enters the area.

• Never carry passengers or children even with the blades off.

• Do not mow in reverse unless abso- lutely necessary. Always look down

and behind before and while backing.

• Never carry children. They may fall off and be seriously injured or interfere

with safe machine operation.

• Keep children out of the mowing area and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and when backing, look behind and down for small children.

• Mow up and down slopes (15 ° Max), not across.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Uneven terrain could overturn the

machine. Tall grass can hide obstacles.

• Use slow speed. Choose a low gear so that you will not have to stop or shift

while on the slope.

• Avoid starting or stopping on a slope. If tires lose traction, disengage the

blades and proceed slowly straight down the slope.

• If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.

• Do not turn on slopes unless neces- sary, and then, turn slowly and gradu-

ally downhill, if possible.

_RODUCT SPECIFICATIONS

Gasoline 1.25 Capacity and Unleaded and

Type: Regular

Oil Type SAE 30 (above 32°F)

(API-SF-SJ): SAE 5W-30

(below 32°F)

Oil Capacity: 3.0 Pints Spark Plug: Champion RC12YC

(Gap: ,030")

Ground Speed (MPH):

Forward: 1st 1.1

2nd 1.4

3rd 2.2

4th 3.4

5th 4.3 6th 5.5

Reverse: 1.7

Tire Pressure: Front: 14 PSI

Rear: 12 PSI

Charging 3 Amps Battery System: 5 Amps Headlights

Battery: Amp/Hr: 28

Min. CCA: 230

Case Size: UIR

Blade Bolt Torque: 27-35 Ft. Lbs.

CONGRATULATIONS on your purchase of a new tractor. It has been designed,

engineered and manufactured to give you the best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact a

Sears or other qualified service center. We have competent, well-trained techni-

cians and the proper tools to service or

repair this tractor. Please read and retain this manual. The

instructions will enable you to assemble and maintain your tractor properly.

Always observe the "SAFETY RULES".

REPAIR AGREEMENT

A Repair Agreement is available on this

product. Contact your nearest Sears store for details.

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintain- ing, caring for and using your tractor.

• Follow the instructions under "Mainte- nance" and "Storage" sections of this

owner's manual.

_,WARNING: This tractor is equipped with an internal combustion engine and

should not be used on or near any unimproved forest-covered, brush-

covered or grass-covered land unless the engine's exhaust system is equipped with

a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective

working order by the operator.

In the state of California the above is

required by law (Section 4442 of the California Public Resources Code).

Other states may have similar laws.

Federal laws apply on federal lands. A

spark arrester for the muffler is available through your nearest Sears service

center (See REPAIR PARTS section of this manual).

Steering Wheel

Steering

Wheel Insert

(1) Locknut 1/2-20

_ Steering Wheel

(1) Hex Bolt 1/4-28 x 1-1/4

Adapter

Seat

(1) Hex Bolt

3/8-16 x 1

(1) Locknut 1/4-28

_S Steedng

teering Shaft

Extension

Boot

Keys

(2) Keys

__/(1) Washer

17/32 x 1-3/16 x 12 Gauge

_(1) Knob

For Future Use

Slope Sheet

Video Cassette

Your new tractor has been assembled at the factory with the exception of those parts

left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the

correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR ASSEMBLY 7. Snap steering wheel insert into center A socket wrench set will make assembly

easier. Standard wrench sizes you need are listed below.

(1) 3/4" wrench (1) Pliers (2) 7/16"wrench (1) Utilityknife

(1) Tire pressure gauge When right or left hand is mentioned in

this manual, it means when you are in the

operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM

CARTON UNPACK CARTON

1. Remove all accessible loose parts

and parts boxes from carton.

2. Cut, from top to bottom, along lines on all four corners of carton, and lay

panels flat.

3. Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

of steering wheel.

8. Remove protective materials from

tractor hood and grill.

IMPORTANT: Check for and remove any staples in skid that may puncture tires

where tractor is to roll off skid.

Insert

_/2 Hex Nut

_Large Flat

_sher

Steering __L_. ) /

Whee,f

Steering

Adz Extension

;haft

1/4 Locknut 1/4 Hex

ASSEMBLE EXTENSION SHAFT AND

BOOT

1. Slide extension shaft onto lower steering shaft. Align mounting holes

in extension and lower shafts and install 1/4 hex bolt and Iocknut.

Tighten securely.

IMPORTANT: Tighten bolt and nut securely to 10-12 ft. Ibs torque.

2. Place tabs of steering boot over tab

slots in dash and push down to secure.

INSTALL STEERING WHEEL

3. Position front wheels of the tractor so

they are pointing straight forward.

4. Remove steering wheel adapter from

steering wheel and slide adapter onto steering shaft extension.

5. Position steering wheel so cross bars are horizontal (left to right) and slide

inside boot and onto adapter.

6. Assemble large flat washer, 1/2 hex nut and tighten securely.

Steering

Shaft

CHECK BATTERY

1. Lift seat pan to raised position. NOTE: If this battery is put into service after month and year indicated on label

(label located between terminals) charge battery for minimum of one hour at 6-10

amps. (See "BATTERY" in Maintenance section of this manual for charging instructions),

.Label

Seat

Terminal

INSTALL SEAT

Adjust seat before tightening adjustment

knob.

1. Remove adjustment knob and flat washer securing seat to cardboard

packing and set aside for assembly of

seat to tractor.

2, Pivot seat upward and remove from

the cardboard packing. Remove the

cardboard packing and discard.

3, Place seat on seat pan so head of

shoulder bolt is positioned over large

slotted hole in pan.

4. Push down on seat to engage

shoulder bolt in slot and pull seat towards rear of tractor.

5. Pivot seat and pan forward and assemble adjustment knob and flat

washer loosely. Do not tighten.

6. Lower seat into operating position and

sit in seat.

7. Slide seat until a comfortable position

is reached which allows you to press clutch/brake pedal all the way down.

8. Get off seat without moving its adjusted position.

9. Raise seat and tighten adjustment knob securely.

Seat

Sh_oulder

Bolt

Flat Washer _

NOTE: You may now roll or drive your

tractor off the skid. Follow the appropriate

instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section for location and

function of controls)

1. Press lift lever plunger and raise

attachment lift lever to its highest position.

2. Release parking brake by depressing clutch/brake pedal.

3. Place gearshift lever in neutral (N)

position,

4. Roll tractor forward off skid.

5. Remove banding holding deflector

shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See

Operation section for location and

function of controls)

_.WARNING: Before starting, read,

understand and follow all instructions in the Operation section of this manual. Be

sure tractor is in a well-ventilated area.

Be sure the area in front of tractor is clear

of other people and objects.

1. Be sure all the above assembly steps have been completed.

2. Check engine oil level and fill fuel tank with gasoline.

3. Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

4. Place gear shift lever in neutral (N) position.

5. Press lift lever plunger and raise attachment lift lever to its highest

position.

6. Start the engine. After engine has

started, move throttle control to idle position.

7. Depress clutch/brake pedal into full

"BRAKE" position and hold. Move gearshift lever to 1st gear.

8. Slowly release clutch/brake pedal and

slowly drive tractor off skid.

9. Apply brake to stop tractor, set parking brake and place gearshift lever in

neutral position.

10.Turn ignition key to "STOP" position.

Continue with the instructions that follow.

INSTALL MULCHER PLATE (If previously removed)

1. Raise and hold deflector shield in upright position.

2. Place front of mulcher plate over front of mower deck opening and slide into

place, as shown.

3. Hook front latch into hole on front of

mower deck.

4. Hook rear latch into hole on back of

mower deck.

Mulcher

Deflector

_CAUTION: Do not remove deflector

shield from mower. Raise and hold

shield when attaching mulcher plate and allow it to rest on plate while in opera-

tion.

Plate

Latch Hooks

TO CONVERTTO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in a safe place. Your mower is now ready

for discharging or installation of optional grass catcher accessory.

NOTE: It is not necessary to change

blades. The mulcher blades are de- signed for discharging and bagging also.

CHECK TIRE PRESSURE

The tires on your tractor were overin- flated at the factory for shipping pur-

poses. Correct tire pressure is important for best cutting performance.

• Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS"

section of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See "TO

LEVEL MOWER HOUSING" in the Service and Adjustments section of this

manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for

replacing motion and mower blade drive belts in the Service and Adjustments

section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is

properly adjusted. See "TO ADJUST

BRAKE" in the Service and Adjustments

section of this manual.

/ CHECKLIST

Before you operate and enjoy your new

tractor, we wish to assure that you receive

the best performance and satisfaction from this Quality Product.

Please review the following checklist: ,/All assembly instructions have been

completed.

,/No remaining loose parts in carton. ,/Battery is properly prepared and

charged. (Minimum 1 hour at 6 amps).

,# Seat is adjusted comfortably and

tightened securely.

,/All tires are properly inflated. (For

shipping purposes, the tires were overinflated at the factory).

,/Be sure mower deck is properly leveled

side-to-side/frent-to-rear for best cutting results. (Tires must be properly inflated

for leveling).

,I Check mower and drive belts. Be sure

they are routed properly around pulleys and inside all belt keepers.

,/Check wiring. See that all connections

are still secure and wires are properly clamped.

While learning how to use your tractor, pay extra attention to the following important

items: ,/Engine oil is at proper level.

,/Fuel tank is filled with fresh, clean,

regular unleaded gasoline.

/ Become familiar with all controls - their

location and function. Operate them before you start the engine.

,I Be sure brake system is in safe operat-

ing condition.

These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.

I- ;I

BATrERY CAUTIONOR REVERSE FORWARD FAST SLOW

WARNING

ENGINE ON ENGINE OFF OIL PRESSURE LIGHTS ON OVER TEMP

FUEL CHOKE MOWER HEIGHT PARKING BRAKE UNLOCKED MOWER LIFT

LOCKED

LIGHT

N H L c®) I

ATTACHMENT REVERSE NEUTRAL HIGH LOW PARKING BRAKE

CLUTCH ENGAGED

ATTACHMENT

IGNITION CLUTCH DISENGAGED (SEE SAFETY RULES SECTION)

KEEP AREA CLEAR SLOPE HAZARDS

DANGER, KEEPHANDSANDFEETAWAY

FREE WHEEL

(Automatic Modelsonly)

KNOWYOURTRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING

YOUR TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.

Attachment

Clutch

Ammeter

Throttle/Choke Attachment

Control _ Lift Lever

Clutch/Brake Height Pedal Adjustment

IgnitionSwitch Position

Light Switch

Lift

Plunger

Indicator

Parking Brake Lever

Gearshift Lever

Our tractors conform to the safety standards of the

American National Standards Institute.

AMMETER - Indicates charging (+) or discharging (-) of battery.

ATTACHMENT CLUTCH LEVER - Used to engage the mower blades, or other

attachments mounted to your tractor. A'I-rACHMENT LIFT LEVER - Used to

raise, lower, and adjust the mower deck or other attachments mounted to your

tractor. CLUTCH/BRAKE PEDAL - Used for

declutching and braking the tractor and starting the engine. GEARSHIFT LEVER - Selects the speed

and direction of tractor.

IGNITION SWITCH - Used for starting and stopping the engine.

LIFT LEVER PLUNGER - Used to release attachment lift lever when changing its

position. LIGHT SWITCH POSITION - Turns the

headlights on and off. PARKING BRAKE LEVER - Locks clutch/

brake pedal into the brake position. THROTTLE/CHOKE CONTROL - Used

for starting and controlling engine speed.

The operation of any tractor can result in foreign objects thrown into

the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any

adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USEYOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator presence sensing switch. When engine

is running, any attempt by the operator to leave the seat without first setting the

parking brake will shut off the engine.

1. Depress clutch/brake pedal all the way down and hold.

2. Pull parking brake lever up and release pressure from clutch/brake pedal. Pedal should remain in brake

position. Make sure parking brake will

hold tractor secure.

Attachment Clutch Lever

"Engaged" Position

_gnition Key

.._._--_..__j/"Disengag ed"

ThrottleF'_ 7--_._/J Position

Choke

A 3ke.--....._\ _,_\\_D" ,,Parking Brake

L;onTrol

"_trol_.__ ,._..._\, \Vl/;'Engaged"

Clutch/ "_.-,." "_-_.---.f/ E, ...

"Disengaged Position Position

STOPPING

MOWER BLADES -

• To stop mower blades, move attach- ment clutch lever to "DISENGAGED"

position.

GROUND DRIVE -

• To stop ground drive, depress clutch/ brake pedal all the way down.

• Move gearshift lever to neutral (N)

position.

ENGINE -

• Move throttle control to slow position.

NOTE: Failure to move throttle control to

slow position and allowing engine to idle before stopping may cause engine to

"backfire".

• Turn ignition key to "STOP" position

and remove key. Always remove key when leaving tractor to prevent

unauthorized use.

• Never use choke to stop engine.

IMPORTANT: Leaving the ignition switch

in any position other than "STOP" will cause the battery to discharge and go dead.

NOTE: Under certain conditions when tractor is standing idle with the engine

running, hot engine exhaust gases may cause "browning" of grass. To eliminate

this possibility, always stop engine when

stopping tractor on grass areas. _,CAUTION: Always stop tractor

completely, as described above, before

leaving the operator's position.

TO USE THROTTLE CONTROL

Always operate engine at full throttle.

• Operating engine at less than full

throttle reduces the battery charging

rate.

• Full throttle offers the best bagging and mower performance.

TO MOVE FORWARD AND BACKWARD The direction and speed of movement is

controlled by the gearshift lever.

1, Start tractor with clutch/brake pedal

depressed and gearshift lever in neutral (N) position.

2. Move gearshift lever to desired position.

3. Slowly release clutch/brake pedal to start movement.

IMPORTANT: Bring tractor to a complete stop before shifting or changing gears.

Failure to do so will shorten the useful life

of your transaxle.

TO ADJUST MOWER cu'n'ING HEIGHT The position of the attachment lift lever

determines the cutting height.

• Grasp lift lever.

• Press plunger with thumb and move lever to desired position.

The cutting height range is approxi-

mately 1-1/2 to 4". The heights are

measured from the ground to the blade tip with the engine not running. These

heights are approximate and may vary depending upon soil conditions, height of

grass and types of grass being mowed.

• The average lawn should be cut to approximately 2-1/2 inches during the

cool season and to over 3 inches during hot months. For healthier and

better looking lawns, mow often and after moderate growth.

• For best cutting performance, grass over 6 inches in height should be

mowed twice. Make the first cut relatively high; the second to desired

height.

TO OPERATE MOWER Your tractor is equipped with an operator

presence sensing switch. Any attempt by

the operator to leave the seat with the

engine running and the attachment clutch engaged will shut off the engine.

1. Select desired height of cut.

2. Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

_,CAUTION: Do not operate the mower without either the entire grass catcher, on

mowers so equipped, or the deflector shield in place.

Attachment Clutch Lever Attachemnt

"Enl Position Position

Low

Position

Deflector Shield

TO OPERATE ON HILLS _)=CAUTION: Do not drive up or down

hills with slopes greater than 15° and do

not drive across any slope. Use the slope guide at the back of this manual.

• Choose the slowest speed before starting up or down hills.

• Avoid stopping or changing speed on

hills.

• If slowing is necessary, move throttle

control lever to slower position.

• If stopping is absolutely necessary,

push clutch/brake pedal quickly to brake position and engage parking

brake.

• Move gearshift lever to 1st gear. Be sure you have allowed room for tractor

to roll slightly as you restart movement.

• To restart movement, slowly release parking brake and clutch/brake pedal.

• Make all turns slowly.

TO TRANSPORT

• Raise attachment lift to highest position with attachment lift control.

• When pushing or towing your tractor, be sure gearshift lever is in neutral (N)

position.

• Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage

when transporting your tractor on a truck

or a trailer, be sure hood is closed and secured to tractor. Use an appropriate

means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH-

MENTS

Tow only the attachments that are

recommended by and comply with specifications of the manufacturer of your

tractor. Use common sense when towing. Too heavy of a load, while on a slope, is

dangerous. 13res can lose traction with the ground and cause you to lose control

of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL The engine in your tractor has been

shipped, from the factory, already filled with summer weight oil.

1. Check engine oil with tractor on level ground.

2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw

cap tight, wait for a few seconds,

remove and read oil level. If neces- sary, add oil until "FULL" mark on

dipstick is reached. Do not overfill.

• For cold weather operation you should

change oil for easier starting (See "OIL

VISCOSITY CHART" in the Mainte- nance section of this manual).

• To change engine oil, see the Mainte- nance section in this manual.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do

not overfill. Use fresh, clean, regular

unleaded gasoline with a minimum of

87 octane. (Use of leaded gasoline will increase carbon and lead oxide

deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in

quantities that can be used within 30 days to assure fuel freshness.

,_CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

near an open flame. IMPORTANT: When operating in

temperatures below32°F(0°C), use fresh,

clean winter grade gasoline to help

insure good cold weather starting. _IbCAUTION: Alcohol blended fuels

(called gasohol or using ethanol or methanol) can attract moisture which

leads to separation and formation of acids during storage. Acidic gas can

damage the fuel system of an engine while in storage. To avoid engine

problems, the fuel system should be emptied before storage of 30 days or

longer. Drain the gas tank, start the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next season. See Storage Instructions for

additional information. Never use engine or carburetor cleaner products in the fuel

tank or permanent damage may occur.

TO START ENGINE

When starting the engine for the first time or if the engine has run out of fuel, it will take extra

cranking time to move fuel from the tank to the engine.

1. Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

2. Place gear shift lever in neutral (N) position.

3. Move attachment clutch to disen- gaged position.

4. Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starUng procedures below.

5. Insert key into ignition and turn key

clockwise to start position and release key as soon as engine starts. Do not

run starter continuously for more than fifteen seconds per minute. If the

engine does not start after several attempts, move throttle control to fast

position, wait a few minutes and try again. If engine still does not start,

move the throttle control back to the

choke position and retry.

WARM WEATHER STARTING (50° F and above)

6. When engine starts, move the throttle

control to the fast position.

• The attachments and ground drive can now be used. If the engine does not

accept the load, restart the engine and allow it to warm up for one minute

using the choke as described above.

COLD WEATHER STARTING ( 50 ° F and below)

6. When engine starts, leave throttle control in choke position until engine

warms up and begins to run roughly.

Once rough running begins, immedi- ately move the throttle control to the

fast position. Engine warm-up may take from several seconds to several

minutes (the colder the temperature, the longer the warm-up).

• The attachments can also be used

during the engine warm-up period.

NOTE: Ifat a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the

carburetor fuel mixture may need to be adjusted for best engine performance (see

"1-OADJUST CARBURETOR" in the Service and Adjustments section of this manual).

MOWING TIPS

• Mower should be properly leveled for best mowing performance. See "TO

LEVEL MOWER HOUSING" in the Service and Adjustments section of this

manual.

• The left hand side of mower should be used for trimming.

• Drive so that clippings are discharged onto the area that has already been cut. Have the cut area to the right of the tractor. This will result in a more even

distribution of clippings and more

uniform cutting.

• When mowing large areas, start by

turning to the right so that clippings will

discharge away from shrubs, fences, driveways, etc. After one or two

rounds, mow in the opposite direction making left hand turns until finished.

• If grass is extremely tall, it should be mowed twice to reduce load and

possible fire hazard from dried clippings. Make first cut relatively high;

the second to the desired height.

• Do not mow grass when it is wet. Wet

grass will plug mower and leave undesirable clumps. Allow grass to

dry before mowing.

• Always operate engine at full throttle

when mowing to assure better mowing performance and proper discharge of

material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well

as the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain

and give best performance of the attachment being used.

MULCHING MOWING TIPS

IMPORTANT: For best performance, keep mower housing free of built-up

grass and trash. Clean after each use.

• The special mulching blade will recut

the grass clippings many times and

reduce them in size so that as they fall

onto the lawn they will disperse into the grass and not be noticed. Also, the

mulched grass will biodegrade quickly

to provide nutrients for the lawn. Always mulch with your highest engine

(blade) speed as this will provide the best recutting action of the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and

interferes with the mulching action. The best time to mow your lawn is the

early afternoon. At this time the grass has dried and the newly cut area will

not be exposed to the direct sun.

• For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass

blades. For extremely heavy grass, reduce your width of cut on each pass

and mow slowly.

MAX 1/3

• Certain types of grass and grass conditions may require that an area be

mulched a second time to completely hide the clippings. When doing a

second cut, mow across or perpendicu- lar to the first cut path.

• Change your cutting pattern from week to week. Mow north to south one week

then change to east to west the next week. This will help prevent matting

and graining of the lawn.

FILL IN DATES

1_ m

Check Tire Pressure I V' Chock Operator Presence and

T Interlock Systems I_ R CheckforLoose Fasteners if V's

A Sharpen/Replace Mower Blades _3

Lubdcafion Chart If

T Check Battery Level

R clean Battery and Terminals If If

Check Transaxte Cooling Check V-BaRs It_

Check Engine Oil Level _ _ If Change Engine Oil (wi_ oil filter) I_1_

Change Engine Oil (without oil filter) V'l.= ]._

N CteanAir F,ter _:

G Clean Air Screen

NI inspect Muffler/Spark Arrester

E Replace Oil Fifier (If equipped) (1_.2

Clean Engine Cooling Fins If 2 Replace Spark Plug if t# 1'

Replace Air Filter Paper Cartridge V'2 Replace Fuel Filter _1_

I * Change more often when operating under a heavy load or

in high ambient temperatures.

2 - Service mote olten when operating lo dirty or dusly conditions,

3 - Replace blades more omen when mowlng in sandy soil 4 * Not required if equipped with maintenance-free battery

5 - Tighten front axle pivot bolt to 35 ft,-Ibs, maximum.

DO not overtighten.

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover

items that have been subjected to operator abuse or negligence. To receive full value

from the warranty, operator must maintain tractor as instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your

tractor. All adjustments in the Service and

Adjustments section of this manual should be checked at least once each season.

• Once a year you should replace the spark plug, clean or replace air filter, and

check blades and belts for wear. A new spark plug and clean air filter assure

proper air-fuel mixture and help your engine run better and last longer.

BEFOREEACHUSE

1. Check engine oil level.

2. Check brake operation.

3. Check tire pressure.

4. Check operator presence and

interlock systems for proper operation.

5. Check for loose fasteners.

LUBRICATION CHART

_) Spindle - _) Spindle

Zerk Zerk

@)FrontWheel :Wheel

Bearing Bearing Zerk

Zerk

_)Engine .

I I

't '-- ,--' _ shift '_- J '-- _" Pivots

_SAE 30 or 10w30 MOTOR OIL (_GENERAL PURPOSE GREASE (_REFER TO Maintenance "ENGINE"

SECTION IMPORTANT: Do not oil or grease the

pivot points which have special nylon bearings. Viscous lubricants will attract

dust and dirt that will shorten the life of the self-lubricating bearings. If you feel

they must be lubricated, use only a dry, powdered graphite type lubricant

17sparingly.

"_Gear-

+ 39 hidden pages