Page 1
706.596680 6-Drawer Chest
Owners
706.596690 7-Drawer Roll-A-Way
Craftsman 7-Drawer Roll-Away Craftsman 6-Drawer AXS™ Chest
Manual
Section Description
1612
1613
1614
1615
1616
1617
1618 Locking System
1623 Lock Replacement
1624
1625
Chest Top and Facia
Drawer and Work Surface
Bottom Replacement
Top, Wiring Harness, Harness Grommet
Chest Top without Task Light
Task Light Replacement
Striker Replacement
Drawer Front Replacement
Page 2
CRRFTSMRN
CHEST TOP AND FACIA
PARTS REPLACEMENT
Information Center
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA
F1612
Page 3
CHEST TOP INSTALLATION AND REMOVAL
Tools Required:
3/8" Wrench
(With task light)
Chest Top Removal
• Disconnect power from unit.
• Remove enough drawers to reach the
top back inside of the unit. {See
Drawer installation and removal.)
• Push actuator rod to back of unit to
disconnect from back of lock. Move
actuator rod for access.
• Remove (4) screws holding top in
place.
• Lift top off of unit enough to reach the
wiring harness.
• Disconnect wiring harness from unit.
• Remove top from unit.
Chest Top installation
• Connect wiring harness to top.
• Position top on unit.
• Attach using (4) screws.
• Make sure the back of the actuator
rod is inserted into the actuator rod
holder in the back of the unit.
• Push actuator rod toward back of unit
and line up with lock. Insert the
actuator rod into the back of the lock.
• Test lock operation.
• Reinstall drawers.
• Reconnect power to the unit.
Page 4
INFORMATION CENTER INSTALLATION
Tools Required:
Screwdriver, Crosstip
Tape
AND REMOVAL
Removal
• Disconnect power from the unit.
• Remove enough drawers to reach the
retaining screw under the information
center. (See removing and installing
drawers.)
• Loosen (do not remove) the retaining
screw under the information center.
• Pull the information center straight out
to remove.
Note: Tape wire to unit before
unplugging the information center. This
wiil prevent the wire from retracting into
the unit.
• Unplug the information center.
Tape wire in
Installation
• Plug in information center.
• Position information center in unit.
• Tighten retaining screw enough to
hold information center in place. Do
not overtighten.
• Reinstall drawers. (See Removing
and installing drawers.)
• Reconnect power to unit.
• Set information center as desired.
(See information center operation.)
Press to
Page 5
FACIA INSTALLATION AND REMOVAL
Tools Required:
3/8" Wrench
drill
5/32" drill bit
Rivet gun
Pliers
To remove facia
• Remove enough drawers to reach the
top back inside of the chest.
• Remove lock. (See lock installation
and removal.)
• Remove chest top. See chest top
installation and removal.
• Carefully drill out (2) rivets holding
facia to chest.
• Remove facia.
To reinstall facia
• Position facia on unit. Make sure
connector is on top of chest.
• Attach using (2) rivets supplied.
• Reinstall lock, chest top, and drawers.
LOCK INSTALLATION AND REMOVAL
Rivet
LOCK INSTALLATION AND
REMOVAL
To remove lock
• Remove enough drawers to reach the
lock retaining clip behind the lock.
• Remove lock retaining clip. Pull lock
out to remove.
To reinstall lock
• Position lock in unit. Install retaining
clip to hold lock in place.
• Make sure the back of the actuator
rod is inserted into the actuator rod
holder in the back of the unit.
• Push actuator rod toward back of unit
and line up with lock. Insert the
actuator rod into the back of the lock.
• Test lock operation.
• Reinstall drawers.
Lock
Page 6
CONNECTING POWER
• Ensure that the unit and power cord
are clean and dry.
• Insert the round end of the power cord
connector into the jack in the back of
the unit.
• Plug the cord into an appropriate
electrical outlet.
Fuse block
To reinstall, carefully align the slides and
push the drawer into the unit until the
drawer stops.
INFORMATION CENTER
OPERATION
The information center is equipped with a
battery backup to maintain memory only.
The display will not function while power
is disconnected from the unit.
REMOVING AND INSTALLING
DRAWERS:
• Empty the drawer.
• Fully extend the drawer.
Release
Lever Style - Lift or
ower (depending on the
slide) the release lever
on both sides, (this
allows the slides to ride
over the stops.) Pull out
to remove.
Tab Style - Depress the
release tabs on both
sides, (this allows the
slides to ride over the
stops.) Pull out to
remove.
Outside temperature display requires
optional outside temperature sensor.
Display backlight
• Pressing ( tight ) turns the display
backlight on for 15 seconds.
Setting the current time
• Press and hold { Clock Set) for at least
two seconds. (Second resets to zero
and hour begins to flash.)
• Press ( Clock) to set am/pm or 24 hour
mode as desired. Note: The am/pm
indicator is not shown in 24 hour
mode.
• Adjust hour using (T) and Q.
• Pressing ( Clock') toggles to next field.
Note: To toggle to minute without
changing hour, press (T) then Q then
C Clock y
• Adjust minute using (¿) and Q.
• Press ( Clock ) to toggle to next field.
• Repeat to adjust Month, Day, and
Year.
• Toggling past year exits set mode.
• Day of week is displayed according to
Month, Day, and Year.
Page 7
Temperature Display
Pressing ( °f;°c ) toggles inside and
outside temperature displays between
Celsius and Fahrenheit.
• Pressing ( Temp ) toggles inside and
outside temperature displays between
• ACT (Actual temperature)
• MIN (Minimum recorded
temperature since last reset)
MAX (Maximum recorded
temperature since last reset)
• Press and hold ( Temp ') for at least two
seconds to clear inside and outside
minimum and maximum recorded
temperatures.
• An audible beep will sound when
temperature is reset.
Setting the alarm
• Press and hold ( Alarm Set ) for at least
two seconds. (Second resets to zero
and hour begins to flash.)
• Adjust hour using (J) and Q-
• Pressing ( Alarm ') toggles to next field.
• Repeat to adjust minute.
• Toggling past minute exits set mode.
Turning alarm on or off
When the alarm is activated, the display
will show the indicator
• Press ( Alarm ) to activate or deactivate
the alarm.
• Press () Alarm ) to Silence alarm when
ringing.
Timer function
• Press ( Timer) to enter timer mode.
• Press ((start/stop ) to Start timer.
• Each time ( start/stop ) is pressed starts
or stops timer.
• Press and hold Q start/stop ^ for at least
two seconds to reset timer to zero.
Count down timer function
• Press and hold ( Timer') for at least two
seconds.
• Display shows 00:00:00 and hour
begins to flash.
• Adjust hour using (+) and Q .
• Pressing ( Timer ~) toggles to next field.
• Repeat to adjust minute and second.
• Toggling past second exits set mode.
Note: To set timer to 24 hours, toggle
display to 00:00:00.
• Press ( start/stop ) to Start count down.
• Each time ( start/stop } is pressed starts
or stops timer.
• Alarm sounds when timer reaches
00:00:00.
• Press any button to silence the alarm.
Clock
When in Timer or Count down timer
mode, press ( Clock) to display current
time. Press ( Timer) to return to timer or
count down timer.
Alarm
Page 8
CRRFTSMRN
DRAWER AND WORK SURFACE
PARTS REPLACEMENT
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA
F1613
Page 9
Tools Required:
Drill
5/32" Drill bit
Rivet gun
SLIDE REPLACEMENT
Removal
• Remove drawer or work surface from
unit. (See drawer and work surface
installation and removal.)
• Carefully drill out rivet holding slide
drawer member to drawer or work
surface.
• Rotate front of slide drawer member
down and out.
• Pull slide forward to remove.
• Carefully drill out rivet holding slide
unit member in place.
• Pull slide unit member forward to
remove.
Installation
• Separate slide drawer member from
unit member. (See drawer and work
surface installation and removal.)
• Install new slide unit member. (Install
back hanger first.)
• Rivet unit member in place as shown.
• Install drawer member. (Install back
hanger first.)
• Install rivet to hold slide drawer
member in place.
• Reinstall drawer or work surface into
unit. (See drawer and work surface
installation and removal.)
Page 10
DRAWER AND WORK SURFACE REPLACEMENT
Tools Required:
Drill
5/32" Drill bit
Rivet gun
Crosstip screwdriver
Removal
• Remove drawer or work surface from
unit. (See Drawer and Work surface
installation and removal.)
• Carefully drill out rivets holding slides
to drawer.
• Rotate front of slide down and out.
• Pull slide forward to remove.
Drawers only
• Remove striker. (See striker
replacement.)
• Remove drawer front. (See drawer
front replacement.)
Right side
Installation
• Install slides on new drawer or work
surface. (Install back hangers first.)
• Install rivets to hold slides in place.
Drawers only
• Install striker. (See striker
replacement.)
• Install drawer front. (See drawer front
replacement.)
Drawers and work surface
• Install drawer or work surface in unit.
See drawer and work surface
installation and removal.
Slide
Page 11
DRAWER FRONT INSTALLATION AND REMOVAL
Tools Required:
Crosstip screwdriver
Removal
• Remove retaining screw(s).
• Slide drawer front assembly as
indicated to unhook mounting tabs.
• Pull out to remove.
Installation
• Position drawer front on drawer
assembly.
• Insert mounting tabs into notches on
drawer.
• Slide drawer front over to attach.
• Install retaining screw(s) to hold
drawer front in place.
Page 12
DRAWER AND WORK SURFACE
INSTALLATION AND REMOVAL
Note: For pull out work surface without
task light, follow drawer removal
instructions.
DRAWER
• Empty the drawer.
• Fully extend the drawer.
Release
Lever Style - Lift or
ower (depending on the
slide) the release lever
on both sides, (this
allows the slides to ride
over the stops.) Pull out
to remove.
Tab Style - Depress the
release tabs on both
sides, (this allows the
slides to ride over the
stops.) Pull out to
remove.
To reinstall, carefully align the slides
and push the drawer into the unit until
the drawer stops.
PULL OUT WORK SURFACE WITH
TASK LIGHT
Removal
• Disconnect the power from the unit.
• Remove enough drawers to gain
access to connections in the back of
the roll-away behind the work
surface.(Follow drawer removal
instructions.)
Page 13
Unplug work surface cord from back of
roll-away.
Remove and save back retaining clip.
Disconnect chain inside back of rollaway. (Move chain toward large round
part of slot. Pull out to remove.)
Remove the work surface. (See
drawer removal instructions.)
Retaining
Installation
• To reinstall, carefully align the slides
and push the work surface into the unit
until the work surface stops.
• Depress release tabs in back corners
of the extendable work surface.
• Push the work surface into the unit to
the fully retracted position.
• Extend work surface far enough to
gain access to connections in back.
• Connect chain inside back of roil
away. (Insert chain into the large
round part of the slot. Slide chain to
small end of slot.)
• Insert retaining clip to hold chain in
place.
• Plug work surface cord into back of
roll-away.
• Reconnect power to the unit. (See:
Connecting power.)
• Check work surface and task lighting
for proper operation.
• Reinstall drawers.
Page 14
Tools Required:
Socket Wrench
5/16" Socket
CRRFTSMRN
BOTTOM REPLACEMENT
Removal
• Disconnect power from the unit.
• Remove contents from drawers.
• Carefully lay the chest on its back.
Take care to prevent scratches or
damage to the unit.
• Remove (5) screws holding bottom on
unit.
• Remove bottom from unit.
• Remove counterweight from plastic
bottom.
Installation
• Install counterweight in new plastic
bottom.
• Position new chest bottom on chest.
• Attach using (5) new mounting
screws.
• Return the chest to its upright
position.
• Reconnect power to the unit.
F1614
Page 15
Page 16
CRRFTSMRN
TOP, WIRING HARNESS, HARNESS GROMMET
Parts Replacement
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA
Harness grommet
F1615
Page 17
Tools Required:
3/8" Wrench
WIRING HARNESS REPLACEMENT
HARNESS GROMMET REPLACEMENT
WIRING HARNESS AND HARNESS
GROMMET REMOVAL
• Disconnect power from unit.
• Remove pull out work surface and
enough drawers to reach the top back
inside of the unit. (See drawer and
work surface installation and
removal.)
• Remove lock and top from roll-away.
(See roll-away top removal and
installation.)
• Remove harness grommet from rollaway.
WIRING HARNESS REMOVAL
• For units with accent lighting under
roll-away, remove bottom drawer and
disconnect accent lighting.
• Remove wiring harness through hole
in roll-away top.
WIRING HARNESS AND HARNESS
GROMMET INSTALLATION
• Insert new wiring harness assembly
into mounting track through hole in top
of roll-away (connector should be on
top.) Slide wiring harness assembly to
bottom of roll-away.
• Install harness grommet over
connector. Insert into hole in top of
roll-away.
• Reinstall top and lock
• If unit has accent lighting, reconnect
accent lighting.
• Test lock operation.
• Reinstall drawers.
• Reconnect power to the unit.
Harness
Grommet
Page 18
TOP INSTALLATION AND REMOVAL
Tools Required:
Screwdriver, Crosstip
Roll-away top removal
• Disconnect power from unit.
• Remove pull out work surface. (See
drawer and work surface installation
and removal.)
• Remove enough drawers to reach the
top back inside of the unit. (See
Drawer and Work surface installation
and removal.)
• Remove lock retaining clip. Pull lock
out to remove.
• Remove (4) screws holding top in
place.
• Lift top off of unit enough to reach the
wiring harness.
• Disconnect wiring harness from unit.
• Remove top from unit.
Roll-away top installation
• Connect wiring harness to top.
Position top on unit. Attach using (4)
screws.
• Position lock in unit. Install retaining
clip to hold lock in place.
• Make sure the back of the lock rod is
inserted into the lock rod holder in the
back of the unit.
• Push the lock rod toward the back of
unit the and line up with lock. Insert
the lock rod into the back of the lock.
• Test lock operation.
• Reinstall drawers.
• Reinstall work surface.
• Reconnect power to the unit.
Page 19
DRAWER AND WORK SURFACE
INSTALLATION AND REMOVAL
Note: For pull out work surface without
task light, follow drawer removal
instructions.
DRAWER
• Empty the drawer.
• Fuliy extend the drawer.
Release
Lever Style - Lift or
ower (depending on the
slide) the release lever
on both sides, (this
allows the slides to ride
over the stops.) Pull out
to remove.
Tab Style - Depress the
release tabs on both
sides, (this allows the
slides to ride over the
stops.) Pull out to
remove.
To reinstall, carefully align the slides
and push the drawer into the unit until
the drawer stops.
PULL OUT WORK SURFACE WITH
TASK LIGHT
Removal
• Disconnect the power from the unit.
• Remove enough drawers to gain
access to connections in the back of
the roll-away behind the work surface.
Unplug work surface cord from back of
roll-away.
Remove and save back retaining clip.
Disconnect chain inside back of rollaway. (Move chain toward large round
part of slot. Pull out to remove.)
Remove the work surface. (See
drawer removal instructions.)
Retaining
To reinstall, carefully align the slides
and push the work surface into the unit
until the work surface stops.
Depress release tabs in back corners
of the extendable work surface.
Push the work surface into the unit to
the fully retracted position.
Extend work surface far enough to
gain access to connections in back.
Connect chain inside back of roil
away. (Insert chain into the large
round part of the slot. Slide chain to
small end of slot.)
Insert retaining clip to hold chain in
place.
Plug work surface cord into back of
roll-away.
Reconnect power to the unit. (See:
Connecting power.)
Check work surface and task lighting
for proper operation.
Reinstall drawers.
Page 20
CHEST TOP WITHOUT TASK LIGHT
Tools Required:
Screwdriver, Crosstip
CRRFTSMRN
Chest top removal
• Disconnect power from unit.
• Remove pull out work surface. (See
drawer installation and removal.)
• Remove enough drawers to reach the
top back inside of the unit. (See
Drawer installation and removal.)
• Remove lock retaining clip. Pull lock
out to remove.
• Remove (4) screws holding top in
place.
• Remove top from unit.
Chest top installation
• Position top on unit. Attach using (4)
screws.
• Position lock in unit. Install retaining
clip to hold lock in place.
• Make sure the back of the lock rod is
inserted into the lock rod holder in the
back of the unit.
• Push the lock rod toward the back of
unit the and line up with lock. Insert
the lock rod into the back of the lock.
• Test lock operation.
• Reinstall drawers.
• Reconnect power to the unit.
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA
F1616
Page 21
DRAWER INSTALLATION AND
REMOVAL
Empty the drawer.
Fully extend the drawer.
Release
Lever Style - Lift or
ower (depending on the
slide) the release lever
on both sides, (this
allows the slides to ride
over the stops.) Pull out
to remove.
Tab Style - Depress the
release tabs on both
sides, (this allows the
slides to ride over the
stops.) Pull out to
remove.
To reinstall, carefully align the slides
and push the drawer into the unit until
the drawer stops.
Page 22
Tools Required:
Screwdriver, Crosstip
CRRFTSMRN
TASK LIGHT REPLACEMENT
Removal
• Disconnect power from the unit.
• Fully extend task light assembly.
• Make note of light orientation.
• Remove (6) mounting screws to
remove light.
• Unplug light.
Press to
Installation
• Plug in new light.
• Position new light in unit in same
orientation as original light.
• Fasten new light in place with (6) new
mounting screws.
• Reconnect power to unit.
F1617
Page 23
Page 24
CRRFTSMRN
LOCKING SYSTEM
Parts Replacement
Actuator rod
Lockbar
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA
F1618
Page 25
ACTUATOR ROD AND ACTUATOR CHANNEL REPLACEMENT
ACTUATOR ROD AND ACTUATOR
CHANNEL REMOVAL
• Disconnect power from the unit.
• Remove work surface (Roll-away
only).
• Remove pull out work surface (Rollaway only.) See drawer and work
surface installation and removal.)
• Remove enough drawers to reach the
top back inside of the unit. (See
drawer and work surface installation
and removal.)
• Push actuator rod to back of unit to
disconnect from back of lock.
• Rotate actuator rod straight down.
• Pull out to remove.
ACTUATOR CHANNEL REMOVAL
• Move actuator channel fully to the
right to remove from mounting
flanges.
ACTUATOR CHANNEL
INSTALLATION.
• Install slot in actuator channel over pin
on lock bar. Move actuator channel
fully to the right.
• Insert top flanges on actuator channel
into mounting flanges on inside top of
unit.
ACTUATOR ROD INSTALLATION
• Insert actuator rod into hole in
actuator channel as shown.
• Insert back of actuator rod into
actuator rod holder in top back of unit.
• Push actuator rod toward back of unit
and line up with lock. Insert actuator
rod into back of lock.
• Test lock operation.
• Reinstall drawers.
• Reconnect power to the unit.
Actuator rod to
actuator channel
Page 26
ACTUATOR ROD BRACKET
INSTALLATION AND REMOVAL
Removal
• Disconnect power from unit.
• For roll-aways, remove work surface.
(See drawer and work surface
installation and removal.
• Remove enough drawers to reach the
top back inside of the unit. (See
Drawer and Work surface installation
and removal.)
• Remove top from unit. (See top
installation and removal for your unit.)
• Pull actuator rod bracket forward. Lift
out to remove.
Installation
• Insert actuator rod bracket into hole in
back corner of unit. Ensure actuator
rod bracket snaps into place. Note:
The flexible tab should be in front.
• Reinstall top in unit.
• Insert back of actuator rod into
actuator rod holder in top back of unit.
• Push actuator rod toward back of unit
and line up with lock. Insert actuator
rod into back of lock.
• Test lock operation.
• Reinstall drawers.
• Reconnect power to the unit.
LOCK BAR INSTALLATION AND
REMOVAL
Removal
• Disconnect power from the unit.
• For roll-aways, remove work surface.
(See drawer and work surface
installation and removal.
• Remove all drawers.
• Remove actuator rod and actuator
channel. (See actuator rod and
actuator channel installation and
removal.)
• Remove top from unit.
• See top removal for your unit.
• Lift lock bar out through hole in top of
unit.
Removal
• Insert lock bar through hole in top of
unit.
• Slide lock bar down through lock bar
guide.
• Reinstall top on unit.
• Reinstall actuator channel and
actuator rod.
• Test lock operation.
• Reinstall drawers.
• Reconnect power to the unit.
Page 27
Tools Required:
Screwdriver, Crosstip
TOP INSTALLATION AND REMOVAL
ROLL-AWAYS, CHESTS WITHOUT TASK LIGHT
Removal
• Disconnect power from unit.
• For roll-aways, remove work surface,
(See drawer and work surface
installation and removal.
• Remove enough drawers to reach the
top back inside of the unit. (See
Drawer and Work surface installation
and removal.)
• Remove lock retaining clip. Pull lock
out to remove.
• Remove (4) screws holding top in
place.
• For roll-aways, lift top off of unit
enough to access the wiring harness.
Disconnect wiring harness from unit.
• Remove top from unit.
Installation
• For roll-aways, connect the wiring
harness to unit.
• Position top on unit. Attach using (4)
screws.
• Position lock in unit. Install retaining
clip to hold lock in place.
• Make sure the back of the actuator
rod is inserted into the actuator rod
holder in the back of the unit.
• Push the actuator rod toward the back
of unit the and line up with lock. Insert
the actuator rod into the back of the
lock.
• Test lock operation.
• Reinstall drawers.
• Reinstall work surface.
• Reconnect power to the unit.
Page 28
CHEST TOP INSTALLATION AND REMOVAL
Tools Required:
3/8" Wrench
(With task light)
Chest Top Removal
• Disconnect power from unit.
• Remove enough drawers to reach the
top back inside of the unit. {See
Drawer installation and removal.)
• Push actuator rod to back of unit to
disconnect from back of lock. Move
actuator rod for access.
• Remove (4) screws holding top in
place.
• Lift top off of unit enough to reach the
wiring harness.
• Disconnect wiring harness from unit.
• Remove top from unit.
Chest Top installation
• Connect wiring harness to top.
• Position top on unit.
• Attach using (4) screws.
• Make sure the back of the actuator
rod is inserted into the actuator rod
holder in the back of the unit.
• Push actuator rod toward back of unit
and line up with lock. Insert the
actuator rod into the back of the lock.
• Test lock operation.
• Reinstall drawers.
• Reconnect power to the unit.
Page 29
DRAWER AND WORK SURFACE
INSTALLATION AND REMOVAL
Note: For pull out work surface without
task light, follow drawer removal
instructions.
DRAWER
• Empty the drawer.
• Fuliy extend the drawer.
Release
Lever Style - Lift or
ower (depending on the
slide) the release lever
on both sides, (this
allows the slides to ride
over the stops.) Pull out
to remove.
Tab Style - Depress the
release tabs on both
sides, (this allows the
slides to ride over the
stops.) Pull out to
remove.
To reinstall, carefully align the slides
and push the drawer into the unit until
the drawer stops.
PULL OUT WORK SURFACE WITH
TASK LIGHT
Removal
• Disconnect the power from the unit.
• Remove enough drawers to gain
access to connections in the back of
the roll-away behind the work surface.
Unplug work surface cord from back of
roll-away.
Remove and save back retaining clip.
Disconnect chain inside back of rollaway. (Move chain toward large round
part of slot. Pull out to remove.)
Remove the work surface. (See
drawer removal instructions.)
Retaining
To reinstall, carefully align the slides
and push the work surface into the unit
until the work surface stops.
Depress release tabs in back corners
of the extendable work surface.
Push the work surface into the unit to
the fully retracted position.
Extend work surface far enough to
gain access to connections in back.
Connect chain inside back of roil
away. (Insert chain into the large
round part of the slot. Slide chain to
small end of slot.)
Insert retaining clip to hold chain in
place.
Plug work surface cord into back of
roll-away.
Reconnect power to the unit. (See:
Connecting power.)
Check work surface and task lighting
for proper operation.
Reinstall drawers.
Page 30
CRRFTSMRN
LOCK REPLACEMENT
Removal
• Disconnect power from unit.
• For roll-aways, remove work surface.
(See drawer and work surface
installation and removal
• Remove enough drawers to reach the
lock retaining clip behind the lock.
• Remove lock retaining clip. Pull lock
out to remove.
Installation
• Position lock in unit. Install retaining
clip to hold lock in place.
• Make sure the back of the actuator
rod is inserted into the actuator rod
holder in the back of the unit.
• Push actuator rod toward back of unit
and line up with lock. Insert the
actuator rod into the back of the lock.
• Test lock operation.
• Reinstall drawers.
Lock
Rekeying MASTERLOCK ONEKEY™ lock
The MASTERLOCK® ONE-KEY™
learning lock system allows the
chest and cabinet to be keyed alike.
The lock can also be keyed to most
house keys.
• Insert current key and turn lock to
the right until access notch
appears at top of lock,
• Depress and hold catch through
access notch using re-keying tool
provided.
• Remove key.
• Insert new key.
• Release catch
• Turn lock to center position,
• Remove key
Note: Catch must be depressed to
insert or remove key in right hand
position. Catch may be released
between keys.
Access
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA
FI 623
Page 31
DRAWER AND WORK SURFACE
INSTALLATION AND REMOVAL
Note: For pull out work surface without
task light, follow drawer removal
instructions.
DRAWER
• Empty the drawer.
• Fuliy extend the drawer.
Release
Lever Style - Lift or
ower (depending on the
slide) the release lever
on both sides, (this
allows the slides to ride
over the stops.) Pull out
to remove.
Tab Style - Depress the
release tabs on both
sides, (this allows the
slides to ride over the
stops.) Pull out to
remove.
To reinstall, carefully align the slides
and push the drawer into the unit until
the drawer stops.
PULL OUT WORK SURFACE WITH
TASK LIGHT
Removal
• Disconnect the power from the unit.
• Remove enough drawers to gain
access to connections in the back of
the roll-away behind the work surface.
Unplug work surface cord from back of
roll-away.
Remove and save back retaining clip.
Disconnect chain inside back of rollaway. (Move chain toward large round
part of slot. Pull out to remove.)
Remove the work surface. (See
drawer removal instructions.)
Retaining
To reinstall, carefully align the slides
and push the work surface into the unit
until the work surface stops.
Depress release tabs in back corners
of the extendable work surface.
Push the work surface into the unit to
the fully retracted position.
Extend work surface far enough to
gain access to connections in back.
Connect chain inside back of roil
away. (Insert chain into the large
round part of the slot. Slide chain to
small end of slot.)
Insert retaining clip to hold chain in
place.
Plug work surface cord into back of
roll-away.
Reconnect power to the unit. (See:
Connecting power.)
Check work surface and task lighting
for proper operation.
Reinstall drawers.
Page 32
Tools Required:
Screwdriver
CRRFTSMRN
STRIKER REPLACEMENT
Removal
• Remove drawer from unit.
• Turn drawer upside down.
• Depress (2) detents. Push striker in to
remove.
Depress
detents
Installation
• Turn drawer right side up.
• Position striker in drawer.
• Push striker toward back of drawer
until striker snaps into place.
• Reinstall drawer.
Drawer installation and removal
• Empty the drawer.
• Fully extend the drawer.
Release
Lever Style - Lift or
lower (depending on the
slide) the release lever
on both sides, {this
allows the slides to ride
over the stops.) Pull out
to remove.
Tab Style - Depress the
release tabs on both
sides, {this allows the
slides to ride over the
stops.) Pull out to
remove.
To reinstall, carefully align the slides
and push the drawer into the unit until
the drawer stops.
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA
FI 624
Page 33
Page 34
DRAWER FRONT REPLACEMENT
Tools Required:
Crosstip screwdriver
CRRFTSMRN
Removal
• Remove retaining screw(s).
• Slide drawer front assembly as
indicated to unhook mounting tabs.
• Pull out to remove.
Installation
• Position drawer front on drawer
assembly.
• Insert mounting tabs into notches on
drawer.
• Slide drawer front over to attach.
• Install retaining screw(s) to hold
drawer front in place.
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA
FI 625
Page 35
Loading...