How it Works
Craftsman
Loading...
706.59668
Owner's Manual
18 pgs1.06 Mb0

Craftsman 706.59668, 706.59669 Owner's Manual

706.596680
6-Drawer Chest
Owners
706.596690
Craftsman 7-Drawer AXS TM Roll-Away
7-Drawer Roll-A-Way
Manual
Craftsman 6-Drawer AXS TM Chest
Section
Description
Chest Top and Facia Drawer and Work Surface
Bottom Replacement Top, Wiring Harness, Harness Grommet Chest Top without Task Light
Task Light Replacement Locking System Lock Replacement
Striker Replacement
Drawer Front Replacement
i CRAFTSMAN°i
CHEST TOP AND FACIA
PARTS REPLACEMENT
S
Facia
Chest Top with light
Information Center
CHEST TOP INSTALLATION AND REMOVAL
(With task light)
Tools Required:
3/8" Wrench
Chest Top Removal
• Disconnect power from unit.
• Remove enough drawers to reach the top back inside of the unit. (See Drawer installation and removal.)
• Push actuator rod to back of unit to disconnect from back of lock. Move actuator rod for access.
• Remove (4) screws holding top in place.
• Lift top off of unit enough to reach the wiring harness.
• Disconnect wiring harness from unit.
• Remove top from unit.
Chest Top Installation
• Connect wiring harness to top.
• Position top on unit.
• Attach using (4) screws.
• Make sure the back of the actuator rod is inserted into the actuator rod holder in the back of the unit.
• Push actuator rod toward back of unit and line up with lock. Insert the
actuator rod into the back of the lock.
• Test lock operation.
• Reinstall drawers.
• Reconnect power to the unit.
Press to
release
Disconnect
actuator rod
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA
F1612 2
INFORMATION CENTER INSTALLATION
AND REMOVAL
Tools Required:
Screwdriver, Crosstip Tape
Removal
• Disconnect power from the unit.
• Remove enough drawers to reach the retaining screw under the information center. (See removing and installing drawers.)
• Loosen (do not remove) the retaining screw under the information center.
• Pull the information center straight out to remove.
Note: Tape wire to unit before unplugging the information center. This will prevent the wire from retracting into the unit.
• Unplug the information center.
Installation
• Plug in information center.
• Position information center in unit.
• Tighten retaining screw enough to hold information center in place. Do not overtighten.
• Reinstall drawers. (See Removing and installing drawers.)
• Reconnect power to unit.
• Set information center as desired. (See information center operation.)
Tape wire in
place before
disconnectin(
Press to release
Loosen
retaining screw
FAClA INSTALLATION AND REMOVAL
Tools Required:
3/8" Wrench drill 5/32" drill bit
Rivet gun Pliers
To remove facia
• Remove enough drawers to reach the top back inside of the chest.
• Remove lock. (See lock installation and removal.)
• Remove chest top. See chest top installation and removal.
• Carefully drill out (2) rivets holding facia to chest.
• Remove facia.
Rivet
To reinstall facia
• Position facia on unit. Make sure connector is on top of chest.
• Attach using (2) rivets supplied.
• Reinstall lock, chest top, and drawers.
LOCK INSTALLATION AND REMOVAL
LOCK INSTALLATION AND REMOVAL
To remove lock
• Remove enough drawers to reach the lock retaining clip behind the lock.
• Remove lock retaining clip. Pull lock out to remove.
Actuator
rod
holder
To reinstall lock
• Position lock in unit. Install retaining clip to hold lock in place.
• Make sure the back of the actuator rod is inserted into the actuator rod holder in the back of the unit.
• Push actuator rod toward back of unit and line up with lock. insert the
actuator rod into the back of the lock.
• Test lock operation.
• Reinstall drawers.
Connector
Front
Lock
'Lock
retaining clip
3 4
CONNECTING POWER
• Ensure that the unit and power cord are clean and dry.
• insert the round end of the power cord connector into the jack in the back of the unit.
• Plug the cord into an appropriate electrical outlet.
Fuse block
Jack
Cord
REMOVING AND INSTALLING DRAWERS:
• Empty the drawer.
• Fully extend the drawer.
Release
Lever Style - Lift or lower (depending on the slide) the release lever on both sides, (this
allows the slides to ride over the stops.) Pull out
to remove.
Tab Style - Depress the release tabs on both sides, (this allows the slides to ride over the stops.) Pull out to remove.
To reinstall, carefully align the slides and push the drawer into the unit until the drawer stops.
INFORMATION CENTER OPERATION The information center is equipped with a battery backup to maintain memory only.
The display will not function while power is disconnected from the unit.
Outside temperature display requires optional outside temperature sensor.
Display backlight
• Pressing _ turns the display backlight on for 15 seconds.
Setting the current time
• Press and hold _ for at least two seconds. (Second resets to zero and hour begins to flash.)
• Press _ to set am/pm or 24 hour mode as desired. Note: The am/pm indicator is not shown in 24 hour mode.
• Adjust hour using (_ and (_.
• Pressing _ toggles to next field. Note: To toggle to minute without changing hour, press _) then (_ then
• Adjust minute using (_ and (_.
• Press _ to toggle to next field.
• Repeat to adjust Month, Day, and Year.
• Toggling past year exits set mode.
• Day of week is displayed according to Month, Day, and Year.
Temperature Display Pressing _ toggles inside and outside temperature displays between Celsius and Fahrenheit.
• Pressing _ toggles inside and outside temperature displays between
ACT (Actual temperature)
MIN (Minimum recorded
temperature since last reset)
MAX (Maximum recorded
temperature since last reset)
• Press and hold _ for at least two seconds to clear inside and outside minimum and maximum recorded
temperatures.
• An audible beep will sound when temperature is reset.
Setting the alarm
• Press and hold _ for at least two seconds. (Second resets to zero and hour begins to flash.)
• Adjust hour using (_ and (_).
• Pressing _ toggles to next field.
• Repeat to adjust minute.
• Toggling past minute exits set mode.
Turning alarm on or off When the alarm is activated, the display will show the indicator _,.
• Press _ to activate or deactivate the alarm.
• Press _ to silence alarm when ringing.
Timer function
• Press _ to enter timer mode.
• Press _ to start timer.
• Each time _ is pressed starts or stops timer.
• Press and hold _ for at least two seconds to reset timer to zero.
Count down timer function
• Press and hold _ for at least two seconds.
• Display shows O0:O0:O0 and hour begins to flash.
• Adjust hour using @ and @.
• Pressing @ toggles to next field.
• Repeat to adjust minute and second.
• Toggling past second exits set mode. Note: To set timer to 24 hours, toggle display to 00:00:0O.
• Press _ to start count down.
• Each time _ is pressed starts or stops timer.
• Alarm sounds when timer reaches 0O:00:OO.
• Press any button to silence the alarm.
Clock When in Timer or Count down timer mode, press _ to display current time. Press _ to return to timer
or
count down timer.
oF_eoCP_
Clock Set
Alarm Set-_
(+)
(-)
Time
\
• \\
D
Temp Inside
AM/PM
\ \
\ \
Date
Alarm Activated
jTimer
Start/Stop
Clock
Alarm
Light Temp outside (Accessoryrequired)
5 6
I CRAFTSMAN°I
DRAWER AND WORK SURFACE
PARTS REPLACEMENT
SLIDE REPLACEMENT
Tools Required:
Drill 5/32" Drill bit
Rivet gun
Removal
• Remove drawer or work surface from
unit. (See drawer and work surface installation and removal.)
• Carefully drill out rivet holding slide drawer member to drawer or work
surface.
• Rotate front of slide drawer member down and out.
• Pull slide forward to remove.
• Carefully drill out rivet holding slide unit member in place.
• Pull slide unit member forward to remove.
Installation
• Separate slide drawer member from unit member. (See drawer and work surface installation and removal.)
• install new slide unit member. (Install back hanger first.)
• Rivet unit member in place as shown.
• install drawer member. (Install back hanger first.)
• install rivet to hold slide drawer member in place.
• Reinstall drawer or work surface into unit. (See drawer and work surface installation and removal.)
Work Surface
%,
Slide
Drawer
Left side
Slide
Back hanger
place
Rivet
Hanger pointed up
Drawer
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA
F1613 2
DRAWER AND WORK SURFACE REPLACEMENT DRAWER FRONT INSTALLATION AND REMOVAL
Tools Required:
Drill 5/32" Drill bit
Rivet gun Crosstip screwdriver
Removal
• Remove drawer or work surface from unit. (See Drawer and Work surface installation and removal.)
• Carefully drill out rivets holding slides to drawer.
• Rotate front of slide down and out.
• Pull slide forward to remove.
Drawers only
• Remove striker. (See striker replacement.)
• Remove drawer front. (See drawer front replacement.)
Installation
• Install slides on new drawer or work surface. (install back hangers first.)
• Install rivets to hold slides in place.
Drawers only
• Install striker. (See striker replacement.)
• Install drawer front. (See drawer front replacement.)
Drawers and work surface
• Install drawer or work surface in unit. See drawer and work surface installation and removal.
Tools Required: Crosstip screwdriver
Removal
• Remove retaining screw(s).
• Slide drawer front assembly as indicated to unhook mounting tabs.
• Pull out to remove.
Installation
• Position drawer front on drawer assembly.
• insert mounting tabs into notches on drawer.
• Slide drawer front over to attach.
• install retaining screw(s) to hold drawer front in place.
Mounting tab
Notch
Retaining
screws
Left side
Slide
Striker
\
Rivet
Drawer
Right side
Siide
Hanger
pointed up
Drawer front
o
d-
J ,
Bottom
drawer only
Drawers (4)inches
deep or more only
3 4
Loading...
+ 12 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use