Craftsman 70621200, 706210110 Owner’s Manual

OPERATOR'S MANUAL

®

STAINLESS STEEL CHEST & CABINET

PRODUCT PURCHASED MAY VARY FROM

PICTURE SHOWN.

CALL 1-800=366-7278 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listing of Service Parts.

LOCATING MODEL # INFORMATION
Model numbers and other information required for service parts is

located on a label on the interior right side of the top most drawer.

• The maximum weight for each drawer should be no more than
100 Ibs.

• The maximum product weight, including contents, should be no
more than 1200 pounds for rolling cabinet.

• For casters, use high quality bearing grease, (yearly).

• Lubricate the slides with grease or equivalent,(twice yearly.

• Lubricate lock with graphite, (yearly).

Ball-bearing Slides

• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit's luster finish. Apply the wax as to
a car. The wax will also help protect the unit against scratches.

• Grease and oil can be removed with most standard cleaning

fluids. For safety, use a nonflammable cleaning fluid.

• If drawer liners are supplied, it is recommended they are used

to protect the finish inside the drawers and to make the drawers

easier to clean. The drawer liners may be cleaned with soap and
water.

• This unit has a clearcoat finish. Do not use stainless steel polish
on this unit.

DANGER _ is used to indicate a hazardous situation which,
if not avoided, will result in serious injury or death.

WARNING z_ indicates a hazardous situation which, if not
avoided, could result in serious injury or death.

CAUTION is used to indicate a hazardous situation which, if not
avoided, m_m_a=y,result in minor injury, moderate injury, or property

damage.
CAUTION: Read and follow all Safety Rules and Operating

Instructions before first use of this product.

DANGER ,_,

• DO NOT stand on this product. You may fall or cause product to

tip.

• DO NOT open more than one drawer. The product may become
unstable and tip.

• DO NOT step in the drawers. You may fall or cause product to

tip.

• DO NOT mount this product on a truck bed or any other moving
object.

• DO NOT move the product prior to closing and locking all the
drawers. The drawers could come open and make the product

unstable and tip.

WARNING Z_
* WEAR SAFETY GLASSES when removing or repositioning the

slides.

oWhen moving this product, push it, do not pull it.
oUSE THE BRAKES when not moving this product. This will

prevent the product from rolling.

oDO NOT alter this product in any manner. For example, do not

weld external Iockbars or attach electrical equipment.

oKeep the product on level surfaces. The product may become

unstable and tip if stored or moved on an uneven surface.

oBE CAREFUL when closing the cover. Remove hands before

the cover closes completely.

CAUTION

This product is not designed to be directly lifted with a fork lift, or

to be towed with any mechanical devices.

• The maximum weight for each drawer should never be exceeded.

• Only transport this product empty. Properly secure when trans-
porting.

• DO NOT exceed maximum product weight, including contents.
See Operations Sections: Capacities for more information.

Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 F1940

Tools Required:

5/16 UNC wrench
Cross-tip Screwdriver

CASTER INSTALLATION
Items Needed:
5/16 - 18 UNC screws (16)

Hardware Included:

10-24 UNC Pan Head

Screw (Qty: 8)

5/16-18 UNC Hex Screw
(Qty: 16)

Mounting Bracket (Qty: 2)

. Place the unit on it's top. Use the packaging material to

protect the finish.

. Attach casters using (4) 5/16 - 18 UNC screws in each

caster. Mount both swivel casters on the same side of the
cart as the side handle.

. Wrench tighten all screws. Do not overtighten. Return the

unit to its upright position.

MOUNTING CHEST ON CART
Items Needed:
10-24 UNC Pan Head screws (8)

Mounting Brackets (2)

REMOVING AND INSTALLING DRAWERS
"Empty the drawer.

. Fully extend the drawer.

iNSTALLiNG DRAWERS

Ball bearing slide - Pull slides and slide carrier out to fully
extended position (see illustration.) Hold the slide on the

cabinet while aligning it with the slide on drawer. Slightly
insert one side and repeat for the other side. Slowly push
drawer to its fully closed position to engage slide. Open

drawer and reclose to ensure proper operation.

Lever Style =Lift or lower, depending on the slide, the
release lever on both sides, (this allows the slides to ride

over the stops.) Pull out to remove.

\\

Tab Style - Depress the release tabs on both sides,
(this allows the slides to ride over the stops.)

Pull out to remove.

slide carrier

slide

/

./