Craftsman 706127320 Owner’s Manual

SEARS

Operator's Manual

[RRFTSMRN ®

PREMIUM SERIES

THIS OPERATING INSTRUCTION MANUAL
COVER ALL PREMIUM SERIES TOOL CENTERS,
INTERMIDIATE CHESTS, AND RISER ASSEMBLYS.

Please indicate the following
information from the service

part drawing provided.

Model Number:

Model Description:

*Product you purchased may vary from picture shown*

SAFETY WARNINGS AND CAUTIONS:

• DO NOT stand on this product You may fail which may cause personal injury

• WEAR SAFETY GLASSES when removing or repositioning the slides The tool

could slip which may cause personal injury

• When moving this product, do not pull it Push the product to prevent personal injury

• Stacked products should be bolted together The products could become unstable
and tip, which may cause personal injury or product damage

• Handle and swivel casters must be attached on the same side of the product

• USE THE BRAKES when not moving this product This will prevent the product from
rolling, which may cause personal injury or product damage

• BE CAREFUL when opening more than one drawer The product may become
unstable and tip, which may cause personal injury or product damage

• DO NOT mount this product on a truck bed or any other moving object This may
cause personal injury or product damage

• DO NOT step in the drawers You may fall which may cause personal injury

• Appropriately secure this product before moving it with a forklift

• DO NOT tow with power equipment The product could tip, which may cause
personal injury or product damage

• DO NOT alter this product in any manner For example, do not weld external Iockbars
or attach electrical equipment This may cause product damage or personal injury

• Keep the product on level surfaces The product may become unstable and tip if
stored or moved on an un-IeveI surface, which may cause personal injury or product

damage

• When rearranging the drawers, be careful not to put too many heavy items in the top
drawers The product could become top heavy and tip, which may cause personal

injury or product damage

• BE CAREFUL when closing the cover Remove hands before the cover closes
completely to prevent personal injury

• Close the cover and lock the drawers and doors before moving this product The
drawers or doors could come open and make the product unstable and tip, which

may cause personal injury or product damage

• When locking this product, close the drawers before closing the cover for lock bars to
work properly

• The maximum weight for each drawer should be no more than 25 pounds

• The maximum product weight, including contents, should be no more than 400
pounds for tool centers

CAUTION:

Read and follow all Safety Rules and Operating
Instructions before first use of this product. Retain this document

for future reference.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Made in the U.S.A.

F890A5

4/97

A

Call 1-800-366-7278 for Service Parts E; JlII] II

Refer to Service Parts Drawing for full listing of Service Parts

11

U

HARDWARE:

_ 1/4-20 Hex Nut

<(_ _:_1_# 1/4-20 x 7/16 Hex Screw

_ [_ 8-32 x 1/4 Pan Head Screw

_ 8-32 Hex Nut

<_ _/,_,_> 10-16 x 1/2 Sheet Metal Screw

Rivet

REMOVE CHEST FROM ROLL-
AWAY :

• The unit comes with the chest secured to
the inside of the roll-away by either two or

four 1/4-20 bolts.

• Lay the roll-away down on its back. Use
packaging material to protect the paint

finish.

• Remove the securing bolts from the
underside of the roll-away. Save the

screws for mounting the chest to the roll-
away.

• Remove the chest.

CASTER INSTALLATION:
NOTE: Use adequate manpower for this

operation.

• Lay the roll-away down on its back. Use
packaging material to protect the paint

finish.

• Mount both swivel casters on the same
side of the roll-away. The swivel caster
with the brake goes to the front of the

unit.

• Attach casters using 1/4-20 x 7/16 hex
screws and 1/4-20 hex nuts. Wrench

tighten.

• Return the roll-away to its upright
position.

MOUNTING INTERMEDIATE CHEST:

• Remove all drawers necessary in order to
attach units. Follow the drawer removal

and installation instructions in the
operation section.

• Position the intermediate chest on the
cabinet. Using the intermediate chest

bottom as a template, mark the mounting
hole locations onto the roll-away top. At

each mark drill a 5/16" diameter hole.

• Bolt the units together using two 1/4-20 x
7/16 hex screws and two 1/4-20 hex

nuts.

• Attach to the top chest with two 1/4-20 x
7/16 hex screws and two 1/4-20 hex

nuts.

• Reinstall all drawers. Follow the drawer
removal and installation instructions in the

operation section.

MOUNTING CHEST:

• Remove the drawer from the roll-away
(refer to the drawer removal instructions).

• Lift the chest onto the roll-away. Line up
the holes in the bottom of the chest with

the holes in the top of the roll-away.

• Attach the chest using two 1/4-20 screws
that were used to secure the chest to the

bottom of the roll-away.

• Wrench tighten all screws.

• Replace the drawer (refer to the drawer
installation instructions).

• To remove the chest, reverse the
procedure.

RISER ASSEMBLY:
NOTE: When assembled, the riser

should be the same size, left to right, as
the chest. Use adequate manpower for

this operation.

• Assemble the sides and the back (flange
side up) together using four 8-32 x 1/4

pan head screws and four 8-32 hex nuts.
Finger tighten.

• Position the riser assembly on the roll-
away. Secure using four 10-16 x 1/2

sheet metal screws. Wrench tighten.

• Position the chest on the riser. Secure
using four 10-16 x 1/2 sheet metal

screws. Wrench tighten.

• Wrench tighten the risers four 8-32 x 1/4
pan head screws and 8-32 hex nuts.

st

Back Side

i

%

Cart

SHELF INSTALLATION:

• Place the shelf in the roll-away and line
up the holes.

• Insert four plastic rivets through the sides
of the roll-away.

Shelf--.

Rivets.

\.\

Side_

• Press the rivet pin firmly into the rivet
body to secure the shelf.

• The shelf may be removed by prying the
rivet pins out using a screwdriver.

REMOVING AND INSTALLING
DRAWERS:

• Fully extend the drawer. Then push it
back a quarter of an inch.

• Insert a screwdriver into the slot in the
slide and depress the stop until it clears

the lance. Repeat this procedure for the
other slide. Remove the drawer.

f-- Stop

Lance

3 4