Craftsman 70612550 Owner’s Manual

PART# FI711

m

Operator's Manual

Please indicate the following information from the service part drawing provided.

Model Number:

SAFETY WARNINGS AND CAUTIONS:

• DO NOT stand on this product. You may fall which may cause personal injury.

• WEAR SAFETY GLASSES when removing or repositioning the slides. The tool
could slip which may cause personal injury.

• When moving this product, do not pull it. Push the product to prevent personal
injury.

• Stacked products should be bolted together. The products could become unstable
and tip, which may cause personal injury or product damage.

• Handle and swivel casters must be attached on the same side of the product.

• USE THE BRAKES when not moving this product. This will prevent the product
from rolling, which may cause personal injury or product damage.

• BE CAREFUL when opening more than one drawer. The product may become
unstable and tip, which may cause personal injury or product damage.

• DO NOT mount this product on a truck bed or any other moving object. This may
cause personal injury or product damage.

• DO NOT step in the drawers. You may fall which may cause personal injury.

• Appropriately secure this product before moving it with a forklift.

• DO NOT tow with power equipment. The product could tip, which may cause
personal injury or product damage.

• DO NOT alter this product in any manner. For example, do not weld external
Iockbars or attach electrical equipment. This may cause product damage or

personal injury.

• Keep the product on level surfaces. The product may become unstable and tip if
stored or moved on an un-level surface, which may cause personal injury or
product damage.

• When rearranging the drawers, be careful not to put too many heavy items in the
top drawers. The product could become top heavy and tip, which may cause
personal injury or product damage.

• BE CAREFUL when closing the cover. Remove hands before the cover closes
completely to prevent personal injury.

• Close the cover and lock the drawers and doors before moving this product. The
drawers or doors could come open and make the product unstable and tip, which
may cause personal injury or product damage.

• When locking this product, close the drawers before closing the cover for lock bars
to work properly.

• The maximum weight for each drawer should be no more than 25 pounds.

• The maximum product weight, including contents, should be no more than 300
pounds for tool centers.

Model Description:

*Your model may vary from the one shown.

CAUTION: Read and follow all Safety Rules and Operating Instructions before
first use of this product. Retain this document for future reference.

Distributed by Sears Brands Management Corporation., Hoffman Estates, IL 60179

Call 1-800-4MY-HOME (1-800-469-4663) for Service Parts.
Refer to Service Parts Drawing for full listing of Service Parts.

F1711

HARDWARE:

_ 1/4 2o HEX NUT

,. ....

= k,IET s L SORE¢i

NOTE: Not all instructions apply to

your specific unit.

REMOVE CHEST FROM ROLL-

AW AY:

• The unit comes with the chest secured
to the inside of the roll-away by either

two or four 1/4-20 bolts.

• Lay the roll-away down on its back.

Use packaging material to protect the
paint finish.

• Remove the securing bolts from the

underside of the roll-away. Save the

screws for mounting the chest to the

roll-away.

• Remove the chest.

CASTER INSTALLATION:
NOTE: Use adequate manpower for this

operation.

• Lay the roll-away down on its back.
Use packaging material to protect the

paint finish.

• Mount both swivel casters on the
same side of the roll-away. The

swivel caster with the brake goes to
the front of the unit.

• Attach casters using 1/4-20 x 7/16
hex screws and 1/4-20 hex nuts.

Wrench tighten.

• Return the roll-away to its upright
position.

\\\

\

MOUNTING CHEST:

• Remove the drawer from the roll-away
(refer to the drawer removal
instructions).

• Lift the chest onto the roll-away. Line
up the holes in the bottom of the chest

with the holes in the top of the roll-
away.

• Attach the chest using two 1/4-20

screws that were used to secure the
chest to the bottom of the roll-away.

• Wrench tighten all screws.

• Replace the drawer (refer to the

drawer installation instructions).

• To remove the chest, reverse the
procedure.

RISER ASSEMBLY:

NOTE: When assembled, the riser
should be the same size, left to right, as
the chest. Use adequate manpower for
this operation.

• Assemble the sides and the back
(flange side up) together using four 8-

32 x 1/4 pan head screws and four 8-
32 hex nuts. Finger tighten.

• Position the riser assembly on the
roll-away. Secure using four 10-16 x

1/2 sheet metal screws. Wrench

tighten.

• Position the chest on the riser.
Secure using four 10-16 x 1/2 sheet

metal screws. Wrench tighten.

• Wrench tighten the risers four 8-32 x

1/4 pan head screws and 8-32 hex

nuts.

Back

Side

3 4