Craftsman 695657960 Owner’s Manual
Owner's Manual
Manual del Usuario
I1!'1I
CRRFTS.R. !
HEIGHT ADJUSTABLE CLAMPING TABLE
BANCO DE TRABAJO DE FIJACION R/_PIDA
Model No. 695.65796
Modelo N-°695.65796
CAUTION:
Before using thls
product, read this
manual and
follow all its Safety Rules
and Operating .
Instructions.
PRECAUCION:
Antes de usar este
producto, lea este manual
y slga todas las
instrucclones de
seguridad y de maneJo.
• Safety Instructions • Instrucciones de
• Assembly segurldad
• Operation • Montaje
• Repair Parts = Manejo
• Lista de plezas
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S,A,
WARRANTY ............................................................... 2:
SAFETY INSTRUCTION8 ......................................... 8
INTRODUCTION ........................................................ 4
ASSEMBLY ................................................................ 4
Full One Year Warranty
If this ORAFTSMAN _ Olamplng Table fails to give
complete satisfaction wlthtn one year from the date
of purchase, return It to (or contact) the nearest
8ears Service Center In the United States, and
Sears wilt repair It, free of charge.
OPERATION .............................................................. 5
_PE(31FI{3AT[O_J_..................................................... 8
UN-PACKING AND CHECKING ...........................,..... 9
ESPAI_IOL................................................................ 11
This warranty gives you specific legal rights and you
may also have other rights which vary from state to
state.
Sear=, Roebuck and Co.,
D/817WA_ Hoffman Estates, IL 60179
DO NOT attempt to assemble or operate your
CRAFTSMAN_ Height Adjustable Clamping Tdble until
you have read the safety instructions tnthis section.
Safety Items throughout this manual are labeled with
WARNING or CAUTION,
Means that faltura to fot!ow this
safety statement may result tn
extanelvsproduct damage, serious personal Injury or
death.
Means that failure to fellow thls
safety statement may result In mtnor or
moderate personal In]ury, property or equipment
damage.
DO NOT use this too[ for
scaffolding or as a ladder, Make sure to
fully tighten handles when in use. Maxlmum capacity
380 Ibs,
Read all Instructions.
@ DO NOT load clamplng table withmore than SSolbs.
@ DO NOT apply an unbalanced load which could
result tn the shop stand tippingover.
DO NOT attempt to use your portable
workbench unless the Jaw Is securely
looked in position.
When operating a stationary power tool
such as a Mitre Saw, on your Olamplng
Table, be sure the toolis securely bolted to a separate
piece of plywood and the plywoodIs securely clamped
to the work table. DO NOT clamp or mount stationary
power tool directly to tabletop, This could cause serious
bodily damage.
When operating a portabte power tool
such as a drill, router_ sander or planer:
Always be sure that the workplace Is securely ¢le_'nped
to your Clamping Table, This will avoid kickback which
couldcause serious bodily injury. '
1"o prevent persona[ Injury while
opening or closing your workbench,
always avoid positioning hands or fingers where they
couldget pinched,
® DO NOT stand or climb on the shop stand. It could
fall or_p over causing serious Injury,
® Be sure the shop stsnd's leg set frame assembly Is
in thefuliy opened position before using.
® Dress for safety. DO NOT wear loose clothing,
gloves, necktles or Jewelry (rings, watches); they
can get caught and draw you Into moving parts_
ALWAYS wear non-aIlp footwear; tie back hair.
DO NOT store a_hopstand outdoors or
{na damp location,
@
ALWAYS keep your work area clean, uncluttered
and well lit. DO NOT work o.n or place shop stand
legs on floor surfaces theft are slrppery from
sawdust,oil, water or wax
@
Keep visitors or ohlldren a sadiedistanceaway from
the work area, especially when you're operating a
power tool, Visitors should wear the same safety
equipment as the operator,
@ SAVE THESE INSTRUCTIONS.
2
PACKAGE CONTENTS
Your CRAFTSMAN ° Clamping Table is shipped
completeinonecarton,
Figure I
B
D
Separate ell parts'from packaging materials and check
each Item with Figure 1 and "Table of Loose Parts."
Make sure a!litems are accounted for before dlscardlng
any of the packing material.
!
|
1
1
1
A
iTEM
A
B
C
D
E
F
Q
H
l
J
K
L
M
N
G,--.,,. _ marked wlth ,1"
TABLE OF LOOSE PARTS
DESCRIPTION QTY.
Table Top Assembly................................ !
LooklngHandle, Short .............................2
Legs .........................................................1
SupportPostsAssembly.........................I
Nut,ShortLocklngHandle.......................2
NutHolder................................................2
Foot, Front ..................................................2
Bolt, Support Posts To Top .....................4
b-_IvelPegs .............................................A
PegSupports ........................................... 2
Solid Surface Center Board .....................1
Looldng Handle, Long..............................2
Foot, Back................................................ 2
Nuts_Support Posts To Top ....................4
TOOLS REQUIRED
#3 PhillipsScrewdriver
Adjustable-Head Wrench
Loading...