Craftsman 33731 User Manual
Operator’s Manual
®
Grass Bag Kit
for the 33-inch Wide Cut Mower
Model No. 33731
CAUTION: Before using this product, read this manual and
follow all safety rules and operating instructions.
Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A.
Visit our web site: www.craftsman.com
FORM NO. 769-03115A
5/22/2007
TABLE OF CONTENTS
Assembly and Operation ..................................................3
Español .............................................................................7
Service Numbers ............................................. Back Cover
© Sears Brands, LLC
2
ASSEMBLY AND OPERATION
WARNING
Before installing this accessory, shut the engine off and allow it to cool. Disconnect the spark plug wire from the spark plug. Refer to the
mower’s Operator’s Manual for complete safety instructions. Do not operate the mower without the entire grass bag in place. Turn the mower
off and disconnect the spark plug before emptying the grass bag.
CARTON CONTENTS
Before installing this accessory, remove all parts from the carton.
Carton contents, including items included within the hardware pack,
are shown in Figures 1 and 2. Part numbers are shown in parentheses
and each item has been identified with a letter code, [X], for use when
following the assembly instructions. Reference to right or left side of
the mower is observed from the operating position.
TOOLS REQUIRED
Two 7/16” wrenches or two adjustable wrenches, and one set of pliers.
[A] - Grass bag (764-04052)
[B] - Chute
Assembly
(931-04239)
[D] - Rod Hanger (747-04671)
[E] - Rod Bracket
(787-01569-0637)
[C] - Rod Assembly (647-04110-0637)
INSTALLING THE RIGHT SIDE BRACKET
Shut off engine and disconnect the spark plug wire.
1.
Loosen the four star knobs by turning the knobs counterclockwise
2.
five full rotations, Figure 3.
Figure 3
Removing the Right Side Hardware
Remove the following from the right side of the upper handle,
3.
Figure 4. The hardware removed can be discarded.
Two 1/4-20 screws
•
Two flat washers
•
Two 1/4-20 cap lock nuts
•
Figure 1
[G] - Lock Cap Nut,
1/4-20 (Qty. 4)
(712-0442)
[F] - HH Cap Screw,
1/4-20 x 1.75” (Qty. 4)
(710-0136)
[I] - Cable Tie (Qty. 1)
(726-0209)
Figure 2 - Contents of the hardware pack.
[H] - Washer (Qty. 8)
(736-0463)
Figure 4
3
ASSEMBLY AND OPERATION
Installing the Right Bracket
Align holes in rod assembly [C] with holes in panel and secure
4.
with the following items from the hardware pack, Figure 5:
Two 1/4-20 x 1.75” screws [F]
•
Four flat washers [H]
•
Two 1/4-20 cap lock nuts [G]
•
INSTALLING THE LEFT SIDE BRACKET
Remove the Left Side Hardware
Remove the following from the left side of the upper handle,
5.
Figure 6. The hardware removed can be discarded.
Two 1/4-20 screws
•
Two flat washers
•
Two 1/4-20 cap lock nuts
•
C
F
H
H
G
Figure 5
Installing the Left Bracket
Align holes in rod bracket [E] with holes in panel while placing end
6.
of rod assembly [C] through the bracket. Secure with the following
items from the hardware pack, Figure 7:
Two 1/4-20 x 1.75” screws [F]
•
Four flat washers [H]
•
Two 1/4-20 cap lock nuts [G]
•
TIGHTENING THE HANDLE KNOBS
Tighten the four star knobs loosened in step 2.
7.
Figure 6
E
G
H
C
Figure 7
H
F
4
Loading...